Crystallization behavior, thermal property and biodegradation of poly(3-hydroxybutyrate)/poly(ethylene glycol) grafting copolymer

The poly(3-hydroxybutyrate)(PHB)/poly(ethylene glycol)(PEG) grafting copolymer was successfully prepared by PHB and acrylate groups ended PEGM using AIBN as initiator. The crystallization behavior, thermal stability and environmental biodegradability of PHB/PEG grafting copolymers were investigated with differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA), wide angle X-ray diffraction (WAXD), scanning electron microscopy (SEM), and Biodegradation test in vitro. In the results, all the grafting copolymers were found to show the X-ray diffraction arising from the PHB crystal lattice, while none of the PEG crystallized peaks could be found even though the graft percent reached 20%. This result indicated that PEG molecules were randomly grafted onto PHB chain. The thermal properties measured by DSC showed that the melting temperature(T_m) and glass transition temperature (T_g) were both shifted to lower temperature with the graft percent increasing, and this broadened the narrow processability window of PHB. According to TGA results, the thermal stability of the grafting copolymers is not changed compared to pure PHB. From the biodegradation test, it could be concluded that degradation occurred gradually from the surface to the inside and that the degradation rate could be adjusted by the PEG grafting ratio. In another words, the biodegradation profiles of PHB/PEG grafting copolymer can be controlled. These properties make PHB/PEG grafting copolymer have promising potential applications especially in agriculture fields.     

聚丙交酯/聚乙二醇多嵌段共聚物的合成及其性能

聚丙交酯 (ＰＬＬＡ)由于具有良好的生物降解性和生物相容性 ,在医学领域已经得到了广泛的临床应用 ,近来又被制备成细胞支架大量应用于组织工程中[1,2 ] ,但由于其疏水性而造成细胞亲和性不好 .聚乙二醇 (ＰＥＧ)具有良好的亲水性 ,良好的生物相容性 ,但是ＰＥＧ是非降解性的 ,只有低分子量的ＰＥＧ可以被吞噬细胞所吞噬或透过肾滤膜而排出体外 ,因此 ,低分子量的ＰＥＧ常被用来与丙交酯 (Ｌ ＬＡ)共聚以改善ＰＬＬＡ支架的亲水性 .聚丙交酯 聚乙二醇共聚物 (ＰＬＥ)的三嵌段及两嵌段共聚物的合成及其性能的研究已被广泛报道[3～ 5] .研究…     

Preparation and characterization of biodegradable nanoparticles based on amphiphilic poly(3-hydroxybutyrate)-poly(ethylene glycol)-poly(3-hydroxybutyrate) triblock copolymer

Amphiphilic triblock copolymers of poly(3-hydroxybutyrate)-poly(ethylene glycol)-poly(3-hydroxybutyrate) (PHB-PEG-PHB) were directly synthesized by the ring-opening copolymerization of β-butyrolactone monomer using PEG as macroinitiator. Their structure, thermal properties and crystallization were investigated by ¹H NMR, differential scanning calorimetry (DSC) and X-ray diffraction. It was found that both PHB and PEG blocks were miscible. With the increase in the PHB block length, the triblock copolymers became amorphous because amorphous PHB block remarkably depressed the crystallization of the PEG block. Biodegradable nanoparticles with core-shell structure were prepared in aqueous solution from the amphiphilic triblock copolymers, and characterized by ¹H NMR, SEM and fluorescence. The hydrophobic PHB segments formed the central solid-like core, and stabilized by the hydrophilic PEG block. The nanoparticle size was close related to the initial concentrations of the nanoparticle dispersions and the compositions of the triblock copolymers. Moreover, the PHB-PEG-PHB nanoparticles also showed good drug loading properties, which suggested that they were very suitable as delivery vehicles for hydrophobic drugs.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide),PEG-b-(PNIPAM)_2,were successfully synthesized through atom transfer radical polymerization(ATRP).A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether(PEG).The copolymers were obtained via the ATRP of N-isopropylacrylamide(NIPAM) at 30℃with CuCl/Me_6TREN as a catalyst system and DMF/H_2O(v/v = 3:1) mixture as solvent.The resulting copo...     

Structure and properties of new polyester elastomers composed of poly(trimethylene terephthalate) and poly(ethylene oxide)

Series of PTT-b-PEO copolymers with different composition of rigid PTT and PEO flexible segments were synthesized from dimethyl terephthalate (DMT), 1,3-propanediol (PDO), poly(ethylene glycol) (PEG, M_n = 1000 g/mol) in a two stage process involving transesterification and polycondensation in the melt. The weight fraction of flexible segments was varied between 20 and 70 wt%. The molecular structure of synthesized copolymers was confirmed by ¹H NMR and ¹³C NMR spectroscopy. The superstructure of these polymers was characterized by DSC, DMTA, WAXS and SAXS measurements. It was observed that domains of three types can exist in PTT-b-PEOT copolymers: semi-crystalline PTT, amorphous PEO rich phase (amorphous PEO/PTT blended phase) and semi-crystalline PEO phase. Semi-crystalline PEO phase was observed only at temperature below 0 °C for sample containing the highest concentration of PEO segment. The phase structure, thermal and mechanical properties are effected by copolymer composition. The copolymers containing 30÷70 wt% of PEO segment posses good thermoplastic elastomers properties with high thermal stability. Hardness and tensile strength rise with increase of PTT content in copolymers.     

Photocurable biodegradable poly(ɛ-caprolactone)/poly(ethylene glycol) multiblock copolymers showing shape-memory properties

Biodegradable multiblock copolymers were synthesized by a polycondensation of poly(ɛ-caprolactone) (PCL) diols of molecular weight (MW)=3,000 and poly(ethylene glycol)s (PEG) of MW=3,000 with 4,4′-(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender in diphenyl ether at 180 °C for 2 h, and were characterized by GPC, ¹H-NMR, FTIR, UV, DSC, and WAXS. These photosensitive copolymers were irradiated by a 400-W high-pressure mercury lamp (λ>280 nm) from 5–60 min to form a network structure. The gel contents increased with irradiation time, and attained ca. 90% after 60 min for all copolymers. The degree of swelling in a distilled water at ambient temperature, and the rate of degradation in a phosphate buffer solution (pH 7.2) at 37 °C increased with increasing PEG components. The shape-memory tests were performed by a cyclic thermomechanical experiments for the photocured CAC/PCL/PEG (75/25) films. The film with a gel content of 57% showed the best shape-memory property with strain fixity rate of 100% and strain recovery rate of 88%.     

Influence of poly (ethylene glycol) on the thermal, mechanical, morphological, physical-chemical and biodegradation properties of poly (3-hydroxybutyrate)

Blends of poly (3-hydroxybutyrate) (PHB) with poly (ethylene glycol) (PEG), (PHB/PEG), in different proportions of 100/0, 98/2, 95/5, 90/10, 80/20 and 60/40 wt%, respectively, were investigated for their thermal properties (using differential scanning calorimetry and thermogravimetric analysis), tensile properties, water vapor transmission rate, enzymatic biodegradation (using light microscopy) and mass retention. The addition of plasticizer did not alter the thermal stability of the blends, although an increase in the PEG content reduced the tensile strength and increased the elongation at break of pure PHB.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

聚癸二酸酐-聚乙二醇共聚物的制备与性能研究

研究了高真空熔融缩聚法制备聚癸二酸酐-聚乙二醇(PSA-PEG)共聚物,采用红外光谱(FTIR)、凝胶渗透色谱(GPC)对制备出来的PSA-PEG共聚物进行了结构表征,并进行了共聚物性能的测定.将癸二酸预聚物与不同分子量的PEG共聚,研究了聚合物结构组成与性能之间的关系,并通过改进实验方法,得到分子量分布较窄的共聚物(PDI:1.10),使制备出的PSA-PEG6000共聚物数均分子量Mn由原来的7291增加到12281.     

Determination of multiple thermal degradation mechanisms of poly(3-hydroxybutyrate)

The thermal degradation of poly(3-hydroxybutyrate) (PHB) was investigated by kinetic analyses in detail to clarify its complex degradation behavior, resulting in a finding of mixed mechanisms comprising at least a thermal random degradation with subsequent auto-accelerated transesterification, and a kinetically favored chain reaction from crotonate chain ends. The thermal degradation behavior of PHB varied with changes in time and/or temperature. From the kinetic analysis of changes in molecular weight, it was found that a non-auto-catalytic random degradation proceeding in the initial period was followed by an auto-accelerated reaction in the middle period. From the kinetic analysis of weight loss behavior, it is proposed that there are some kinetically favored scissions occurring at the chain ends, where the degradation proceeded by a 0th-order weight loss process in the middle stage. The observed 0th-order weight loss process was assumed to be an unzipping reaction occurring at ester groups neighboring the crotonate end groups.     

Thermosensitive behavior of poly(ethylene glycol)/poly(2‐(N,N‐dimethylamino)ethyl methacrylate) double hydrophilic block copolymers

The poly(ethylene glycol)/poly(2‐(N,N‐dimethylamino)ethyl methacrylate) (PEG/PDMAEMA) double hydrophilic block copolymers were synthesized by atom transfer radical polymerization using mPEG‐Br or Br‐PEG‐Br as macroinitiators. The narrow molecular weight distribution of PEG/PDMAEMA block copolymers was identified by gel permeation chromatography results. The thermosensitivity of PEG/PDMAEMA block copolymers in aqueous solution was revealed to depend significantly on pH, ionic strength, chain structure, and concentration of the block copolymers. By optimizing these factors, the cloud point temperature of PEG/PDMAEMA block copolymers can be limited within body temperature range (30–37 °C), which suggests that PEG/PDMAEMA block copolymers could be a good candidate for drug delivery systems. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 503–508, 2010     

The Synthesis of Poly(ethylene oxide)-Block-Polybutylacrylate

ＴｈｅＳｙｎｔｈｅｓｉｓｏｆＰｏｌｙ（ｅｔｈｙｌｅｎｅｏｘｉｄｅ）┐Ｂｌｏｃｋ┐Ｐｏｌｙｂｕｔｙｌａｃｒｙｌａｔｅ＊＊ＳｕｐｐｏｒｔｅｄｂｙｔｈｅＮａｔｉｏｎａｌＮａｔｕｒａｌＳｃｉｅｎｃｅＦｏｕｎｄａｔｉｏｎｏｆＣｈｉｎａａｎｄＤｏｃｔｏｒａｌｆｏ...     

Investigation of swelling and network parameters of poly(ethylene glycol)-crosslinked poly(methyl vinyl ether-co-maleic acid) hydrogels

The influence of poly(ethylene glycol) (PEG) plasticiser content and molecular weight on the physicochemical properties of films cast from aqueous blends of poly(methyl vinyl ether-co-maleic acid) was investigated using thermal analysis, swelling studies, scanning electron microscopy (SEM) and attenuated total reflectance (ATR)-Fourier transform infrared (FTIR) spectroscopy. FTIR spectroscopy revealed a shift of the CO peak from 1708 to 1731 cm⁻¹, indicating that an esterification reaction had occurred upon heating, thus producing crosslinked films. Higher molecular weight PEGs (10,000 and 1000 Da, respectively), having greater chain length, producing hydrogel networks with lower crosslink densities and higher average molecular weight between two consecutive crosslinks. Accordingly, such materials exhibited higher swelling rates. Hydrogels crosslinked with a low molecular weight PEG (PEG 200) showed rigid networks with high crosslink densities and, therefore, lower swelling rates. Polymer:plasticizer ratio alteration did not yield any discernable patterns, regardless of the method of analysis. The polymer-water interaction parameter (χ) increased with increases in the crosslink density. SEM studies showed that porosity of the crosslinked films increased with increasing PEG MW, confirming what had been observed with swelling studies and thermal analysis, that the crosslink density must be decreased as the M_w of the crosslinker is increased. Hydrogels containing PMVE/MA/PEG 10,000 could be used for rapid delivery of drug, due to their low crosslink density. Moderately crosslinked PMVE/MA/PEG 1000 hydrogels or highly crosslinked PMVE/MA/PEG 200 systems could then be used in controlling the drug delivery rates. We are currently evaluating these systems, both alone and in combination, for use in sustained release drug delivery devices.     

Melting and thermal history of poly(hydroxybutyrate-co-hydroxyvalerate) using step-scan DSC

Melting behaviour and crystal morphology of poly(3-hydroxybutyrate) (PHB) and its copolymer of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with various hydroxyvalerate (HV) contents [5 wt.% (PHB5HV), 8 wt.% (PHB8HV) and 12 wt.% (PHB12HV)] have been investigated by conventional DSC, step-scan differential scanning calorimetry (SDSC) and hot-stage polarised optical microscopy (HSPOM). Crystallisation behaviour of PHB and its copolymers were investigated by SDSC. Thermal properties were investigated after different crystallisation treatments, fast, medium and slow cooling. Multiple melting peak behaviour was observed for all polymers. SDSC data revealed that PHB and its copolymers undergo melting–recrystallisation–remelting during heating, as evidenced by exothermic peaks in the IsoK baseline (non-reversing signal). An increase in degree of crystallinity due to significant melt–recrystallisation was observed for slow-cooled copolymers. PHB5HV showed different crystal morphologies for various crystallisation conditions. SDSC proved a convenient and precise method for measurement of the apparent thermodynamic specific heat (reversing signal) HSPOM results showed that the crystallisation rates and sizes of spherulites were significantly reduced as crystallisation rate increased.     

Thermal,mechanical and rheological properties of biodegradable poly(propylene carbonate) and poly(butylene carbonate) blends

Poly(propylene carbonate)(PPC) was melt blended in a batch mixer with poly(butylene carbonate)(PBC) in an effort to improve the toughness of the PPC without compromising its biodegradability and biocompatibility. DMA results showed that the PPC/PBC blends were an immiscible two-phase system. With the increase in PBC content, the PPC/PBC blends showed decreased tensile strength, however, the elongation at break was increased to 230% for the 50/50 PPC/PBC blend. From the tensile strength experiments, the Pukanszky model gave credit to the modest interfacial adhesion between PPC and PBC, although PPC/PBC was immscible. The impact strength increased significantly which indicated the toughening effects of the PBC on PPC. SEM examination showed that cavitation and shear yielding were the major toughening mechanisms in the blends subjected the impact tests. TGA measurements showed that the thermal stability of PPC decreased with the incorporation of PBC. Rheological investigation demonstrated that the addition of PBC reduced the value of storage modulus, loss modulus and complex viscosity of the PPC/PBC blends to some extent. Moreover, the addition of PBC was found to increase the processability of PPC in extrusion. The introduction of PBC provided an efficient and novel toughened method to extend the application area of PPC.     

Synthesis and properties of biodegradable copolymers based on 4,4′‐(adipoyldioxy)dicinnamic acid, 1,6‐hexanediol,and poly(ethylene glycol)s

4,4′‐(Adipoyldioxy)dicinnamic acid (CAC) was synthesized by a condensation of adipoyl chloride and 4‐hydroxycinnamic acid. The CAC6 copolymers were prepared by a high‐temperature solution polycondensation of a diacyl chloride of CAC, 1,6‐hexanediol (6), and poly(ethylene glycol) (PEG) in which the molecular weights of PEG are 1000, 2000, and 8300. Differential scanning calorimetric curves of the copolymers exhibited a glass‐transition temperature because of PEG moiety and two melting endotherms (T_m's); the one at the higher T_m was due to CAC6 moiety, and the other at the lower T_m was due to PEG moiety, suggesting that these copolymers are the block type. The incorporation of the PEG component decreased the tensile strength and initial modulus, but increased the elongation extremely. The enzymatic degradation was performed in phosphate buffer solution (pH 7.2) with Ps. cepacia lipase at 37 °C. The degradation rate of the copolymers increased significantly with an increasing content of PEG, which was correlated to the water absorption of the copolymers. All copolymers could undergo photocuring by ultraviolet (UV) light irradiation (λ > 280 nm) at ambient temperature, as examined by UV spectroscopy and solubility. The CAC6/E2000(50/50) film photocured for 3 min exhibited a good elastic property with a maximum tensile strength of 3.7 MPa and maximum elongation of 640%. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2930–2938, 2003     

Assessing the mechanical,phase inversion,and rheological properties of poly-[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyvalerate] (PHBV) blended with poly-(l-lactic acid) (PLA)

Poly-(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and poly-(l-lactic acid) (PLA) have attracted much interest in recent years since they are biodegradable, thus can replace synthetic non-degradable materials. In this study, improvements of PHBV, mechanical, phase inversions, and rheological properties were investigated after blending with PLA in varying ratio’s. Three different blends of commercially available PLAs with 92–98% l-lactide units and one grade of PHB with 5% valerate content were blended using a micro-compounder at 175 °C. The composition of PHBV in blends ranged from 50% to 80%. With the addition of PLA, increases in the flexural strength and elastic modulus were observed for several blends, while minor to no changes were detected in the elongation at break and tensile strength as compared to pure PHBV material. Like many conventional plastics, the complex viscosity decreased with increasing rotational frequency due to decreasing entanglements and molecular weight. The complex viscosity with respect to time was very stable for the blends, but no improvements in the PHBV viscosity were observed with the addition of PLA at 170 °C. Three phase inversion models were used to predict the continuity of the blends, and the results showed both dual- and PLA-continuity phase for the blends. In summary, the mechanical results showed improvements in the tensile and flexural properties, while the rheological observation showed minor improvements in the complex viscosity for numerous concentrations.     

The influence of biotic and abiotic factors on the rate of degradation of poly(lactic) acid (PLA) coupons buried in compost and soil

Poly(lactic) acid (PLA) is a compostable biopolymer and has been commercialised for the for the manufacture of short-shelf life products. As a result, increasing amounts of PLA are entering waste management systems and the environment; however, the degradation mechanism is unclear. While hydrolysis of the polymer occurs abiotically at elevated temperature in the presence of water, potential catalytic role for microbes in this process is yet to be established. In this study, we examined the degradation of PLA coupons from commercial packaging at a range of temperatures (25°, 37°, 45°, 50° and 55 °C) in soil and compost and compared with the degradation rates in sterile aqueous conditions by measuring loss of tensile strength and molecular weight (Mw). In addition, in order to assess the possible influence of abiotic soluble factors in compost and soil on degradation of PLA, degradation rates in microorganism-rich compost and soil were compared with sterile compost and soil extract at 50 °C. Temperature was determined to be the key parameter in PLA degradation and degradation rates in microorganism-rich compost and soil were faster than in sterile water at temperatures 45° and 50 °C determined by tensile strength and Mw loss. Furthermore, all tensile strength was lost faster after 30 and 36 days in microorganism-rich compost and soil, respectively, than in sterile compost and soil extract, 57 and 54 days, respectively at 50 °C. Significantly more Mw, 68% and 64%, was lost in compost and soil, respectively than in compost extract, Mw, 53%; and in soil extract, 57%. Therefore, degradation rates were faster in microorganism-rich compost and soil than in sterile compost and soil extract, which contained the abiotic soluble factors of compost and soil at 50 °C. These comparative studies support a direct role for microorganisms in PLA degradation at elevated temperatures in humid environments. No change in tensile strength or Mw was observed either 25° or 37 °C after 1 year suggesting that accumulation of PLA in the environment may cause future pollution issues.     

L-丙交酯-β-苹果酸共聚物的体外降解及细胞亲和性研究

研究了具有功能侧基的新型生物降解高分子——— [聚 (L 丙交酯 co β 苹果酸 ) ](PLMA)在pH 7 4的磷酸缓冲溶液中的降解和鼠的 3T3成纤维细胞在共聚物膜表面的贴附及生长 .研究了不同组成的共聚物在降解过程中的失重、表面形貌、组成及分子量变化 ,发现PLMA为本体降解 ,共聚物中苹果酸含量的提高可以加速降解 ,降解过程中聚苹果酸 (PMA)链段附近的酯键先水解断裂 .鼠的 3T3成纤维细胞在聚L 丙交酯 (PLLA)均聚物和苹果酸含量为 4mol% ,8mol%和 13mol%的共聚物膜上培养 5h ,细胞贴附率分别为 4 3%、71%、80 %和 4 3% .3T3成纤维细胞在苹果酸含量为 4mol%和 8mol%的共聚物膜上的生长情况好于在PLLA均聚物和苹果酸含量为 13mol%含量的共聚物膜上的生长 .