Toughening of poly(propylene carbonate) by carbon dioxide copolymer poly(urethane-amine) via hydrogen bonding interaction

A carbon dioxide copolymer poly(urethane-amine)(PUA) was blended with poly(propylene carbonate)(PPC) in order to improve the toughness and flexibility of PPC without sacrificing other mechanical properties. Compared with pure PPC, the PPC/PUA blend with 5 wt% PUA loading showed a 400% increase in elongation at break, whilst the corresponding yielding strength remained as high as 33.5 MPa and Young's modulus showed slightly decrease. The intermolecular hydrogen bonding interaction in PPC/PUA blends was comfirmed by FTIR, 2D IR and XPS spectra analysis, and finely dispersed particulate structure of PUA in PPC was observed in the SEM images, which provided good evidence for the toughening mechanism of PPC.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Thermal,Mechanical and Rheological Properties of Eco-friendly Poly（propylene carbonate）/Poly（1,2-propylene succinate） Blends

In order to improve the flexibility of poly（propylene carbonate） （PPC）, poly（1,2-propylene succinate） （PPSu） was used to plasticize PPC in a batch mixer. The effects of PPSu on the miscibility, thermal stability, mechanical and theological properties of the blends were investigated. PPC was partially miscible with PPSu. It was demonstrated that PPSu decreased the glass transition temperature and melt viscosity of PPC, as shown in the DSC and rheological curves. With the increase in PPSu content, the PPC/PPSu blends showed decreased tensile strength, however, the elongation at break was increased to 1100% for the 70/30 PPC/PPSu blend. The introduction of PPSu provided an efficient and novel plasticization method to extend the application area of PPC.     

Fully biodegradable blends of poly(butylene succinate) and poly(butylene carbonate): Miscibility, thermal properties, crystallization behavior and mechanical properties

Fully biodegradable poly(butylene succinate) (PBS) and poly(butylene carbonate) (PBC) blends were prepared by melt blending. Miscibility, thermal properties, crystallization behavior and mechanical properties of PBS/PBC blends were investigated by scanning electron microscopy (SEM), phase contrast optical microscopy (PCOM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and mechanical properties tests. The SEM and PCOM results indicated that PBS was immiscible with PBC. The WAXD results showed that the crystal structures of both PBS and PBC were not changed by blending and the two components crystallized separately in the blends. The isothermal crystallization data showed that the crystallization rate of PBS increased with the increase of PBC content in the blends. The impact strength of PBS was improved significantly by blending with PBC. When the PBC content was 40%, the impact strength of PBS was increased by nearly 9 times.     

Synthesis and Properties of Poly(butylene carbonate-co-spirocyclic carbonate)

Poly(butylene carbonateXPBC) has significantly promising applications as a degradable material in the field of polymers, while its poor thermal performance and low crystallization rate are its main defects. To overcome these shortcomings, a series of poly(butylene carbonate-co-spirocyclic carbonateXPBSC) copolymers were synthesized from diphenyl carbonate, 1,4-butanediol and spiroglycol via two-step polycondensation reactions, using magnesium oxide as a catalyst. Differential scanning calorimetry(DSC) results indicated that the glass transition temperature(Tg) values of PBSC copolymers were enhanced from -19℃ to 56℃ with rising the spiroacetal moiety content. Thermogravimetric analysis(TGA) results showed that the resulting PBSCs have a higher thermal stability than that of poly(butylene carbonate). Wide angle X-ray diflraction(WXRD) patterns were characterized to investigate the crystallization behaviour of PBSCs. Tensile testing demonstrated that copolymerization of spiroacetal moieties into PBC chains imparted PBSC with favourable mechanical performance. Typically, PBSC 30 had a tensile modulus of (1735±430) MPa, a tensile strength of (42±5) MPa and an elongation of 504%±36%.     

Biodegradable Foaming Material of Poly(butylene adipate-co-terephthalate) (PBAT)/Poly(propylene carbonate) (PPC)

A biodegradable blend foaming material of poly(butylene adipate-co-terephthalate)(PBAT)/poly(propylene carbonate)(PPC)was successfully prepared by chemical foaming agent and screw extrusion method.First,PBAT was modified by bis(tert-butyl dioxy isopropyl)benzene(BIBP)for chain extension,and then the extended PBAT(E-PBAT)was foamed with PPC using a twin(single)screw extruder.By analyzing the properties of the blends,we found that Young’s modulus increased from 58.8 MPa of E-PBAT to 244.7 MPa of E-PBAT/PPC 50/50.The viscosity of the polymer has a critical influence on the formation of cells.Compared with neat PBAT(N-PBAT),the viscosity of E-PBAT increased by 3396 Pa·s and E-PBAT/PPC 50/50 increased by 8836 Pa·s.Meanwhile,the dynamic mechanical analysis(DMA)results showed that the storage modulus(E’)at room temperature increased from 538 MPa to 1650 MPa.The various phase morphologies(“sea-island”,“quasi-co-continuous”and“cocontinuous”)and crystallinity of the blends affected the spread velocity of gas and further affected the foaming morphology in E-PBAT/PPC foam.Therefore,through the analysis of phase morphology and foaming mechanism,we concluded that the E-PBAT/PPC 70/30 component has both excellent strength and the best foaming performance.     

Mechanical,thermal and rheological properties and morphology of poly (lactic acid)/poly (propylene carbonate) blends prepared by vane extruder

In this study, the poly (lactic acid) (PLA) and poly (propylene carbonate) (PPC) blends with different compositions were prepared by a novel vane extruder based on elongation rheology. The mechanical properties, morphologies, crystallization behavior, thermal stability, and rheological properties of the blends were investigated. Mechanical test showed that PLA could be toughened by PPC to some extent, and the impact strength of the PLA was maximized when PPC content was about 30%. Differential scanning calorimetry analysis revealed that PPC had little effect on the melting process, the crystallization behavior of PLA component in the blend was improved, and the cold crystallizability of PLA decreased with the increase of PPC content when the PPC content was less than 50%. Thermogravimetry analysis showed that the thermal stability of the blends was improved by compounding with PLA. Scanning electron microscope showed that the dispersion of PLA droplets in PPC matrix was better than that of PPC droplets in PLA matrix. Rheological test showed that the melt viscosity of the pure PLA and the blend with 10% PPC was insensitive to shear rate, and the blends melt appeared shear thinning phenomenon with the increase of PPC content. It also showed that the blends microstructure changed with the addition of PPC and the blends with PPC content in a certain range had similar stress relaxation mechanism. Copyright © 2016 John Wiley & Sons, Ltd.     

Thermal,Rheological and Mechanical Properties of Biodegradable Poly(propylene carbonate)/Epoxidized Soybean Oil Blends

Biodegradable poly(propylene carbonate) (PPC)/epoxidized soybean oil (ESO) blends with different component ratios were prepared by melt blending to improve the performance of PPC.The phase morphology,thermal properties,rheological properties and mechanical properties of the blends were investigated in detail.SEM examination revealed good interfacial adhesion between PPC matrix and ESO.According to DSC and DMA,as the content of ESO increased,the glass transition temperature of the PPC component increased,indicating that there was a strong interfacial interaction between the PPC matrix and ESO.The interracial interaction may be caused by ring-opening reaction between the hydroxyl end groups of PPC and the epoxy groups of ESO,which restricted the chain movement of PPC matrix.The disappearance of the epoxy groups in FTIR indicated that the interfacial interaction between the two phases was due to the ring-opening reaction between PPC and ESO.With the addition of ESO,the thermal stabilities were enhanced.With the increasing ESO content,the modulus gradually decreased.However,the strength at yield,the strength at break and the elongation at break were increased for the PPC/ESO blends,suggesting that the enhancement of the strength and toughness of PPC was achieved by the incorporation of ESO.The rheological measurement revealed that the complex viscosity,storage modulus and loss modulus of PPC were increased with the increasing ESO content at low frequency,which indicated that the addition of ESO enhanced the melt strength of PPC instead of plasticizing PPC.     

水辅助加工法制备聚丙撑碳酸酯/淀粉共混物

分别采用普通熔融共混法和水辅助加工法,制备了具有不同共混形态的聚丙撑碳酸酯(PPC)/淀粉共混物,并研究了淀粉分散形态对共混物的玻璃化转变温度(Tg)、流变以及力学性能的影响。研究结果表明,采用普通熔融共混法时,淀粉未发生糊化,并以原颗粒状分散于基体中;而采用水辅助加工法时,淀粉发生糊化,并在挤出过程中原位形成纤维结构。当淀粉以纤维形式分散于PPC基体中时,其与PPC间的界面接触面积显著增加,二者的相互作用增强,PPC/淀粉共混物的Tg、储能模量以及复合黏度显著提高。力学性能测试结果表明,当淀粉质量分数为30%,采用水辅助加工法制备的PPC/淀粉共混物的拉伸模量相比于纯PPC提高了67.7%。     

线性聚酯酰胺对聚碳酸亚丙酯的改性

通过己内酯和氨基己酸开环、缩合反应制备了酯段含量为81%的线性聚酯酰胺（PEA）,并用熔融共混的方法制备了PEA/聚碳酸亚丙酯（PPC）共混物,考察了PEA的引入对共混体系相容性、热力学稳定性和机械性能的影响。 结果表明,PEA与PPC之间有较好的相容性,共混物的热力学稳定性比PPC有显著提高,当PEA质量分数为3%时,共混体系的起始分解温度（T-5%）和最大分解速率时的温度（Tmax）比PPC分别提高了52.7%和46.4%。 通过调节PEA的含量可以使共混体系同时达到增强和增韧的效果。     

Rheological,thermal and mechanical properties of biodegradable poly(propylene carbonate)/polylactide/Poly(1,2-propylene glycol adipate) blown films

Poly(propylene carbonate)(PPC) was blended with polylactide(PLA) and poly(1,2-propylene glycol adipate)(PPA) using a twin screw extruder. Then the PPC/PLA/PPA films were prepared using the blown film technique. DMA results showed that PPA could act as a plasticizer and improve the miscibility between PPC and PLA. Crystal morphology displayed that blending PLA with the amorphous PPC led to a decrease of the spherulite size of PLA. The results of mechanical tests indicated that PPC-rich films showed high elongation at break and PLA-rich films showed high tear strength and good optical properties. The content of PPC and PLA significantly affected the physical properties of the films. With increasing PPC content, the melt strengths of the PPC/PLA/PPA films were enhanced. These findings contributed to the biodegradable materials application for designing and manufacturing polymer packaging.     

Electron-beam irradiation on poly(propylene carbonate) in the presence of polyfunctional monomers

Poly(propylene carbonate) (PPC) showed predominantly degradation under electron-beam irradiation, accompanied by deterioration of its mechanical performance due to sharp decrease of the molecular weight. Crosslinked PPC was prepared by addition of polyfunctional monomer (PFM) to enhance the mechanical performance of PPC. When 8 wt% of PFM like triallyl isocyanurate (TAIC) was added, crosslinked PPC with a gel fraction of 60.7% was prepared at 50 kGy irradiation dose, which showed a tensile strength at 20 °C of 45.5 MPa, whereas it was only 38.5 MPa for pure PPC. The onset degradation temperature (T_i) and glass transition temperature (T_g) of this crosslinked PPC was 246 °C and 45 °C, respectively, a significant increase related to pure PPC of 211 °C and 36 °C. Therefore, thermal and mechanical performances of PPC could be improved via electron-beam irradiation in the presence of suitable PFM.     

Biodegradable poly(propylene carbonate)/layered double hydroxide composite films with enhanced gas barrier and mechanical properties

Relatively well crystallized and high aspect ratio Mg-Al layered double hydroxides(LDHs) were prepared by coprecipitation process in aqueous solution and further rehydrated to an organic modified LDH(OLDH) in the presence of surfactant. The intercalated structure and high aspect ratio of OLDH were verified by X-ray diffraction(XRD) and scanning electron microscopy(SEM). A series of poly(propylene carbonate)(PPC)/OLDH composite films with different contents of OLDH were prepared via a melt-blending method. Their cross section morphologies, gas barrier properties and tensile strength were investigated as a function of OLDH contents. SEM results show that OLDH platelets are well dispersed within the composites and oriented parallel to the composite sheet plane. The gas barrier properties and tensile strength are obviously enhanced upon the incorporation of OLDH. Particularly, PPC/2%OLDH film exhibits the best barrier properties among all the composite films. Compared with pure PPC, the oxygen permeability coefficient(OP) and water vapor permeability coefficient(WVP) is reduced by 54% and 17% respectively with 2% OLDH addition. Furthermore, the tensile strength of PPC/2%OLDH is 83% higher than that of pure PPC with only small lose of elongation at break. Therefore, PPC/OLDH composite films show great potential application in packaging materials due to its biodegradable properties, superior oxygen and moisture barrier characteristics.     

Preparation and characterization of formaldehyde-modified black liquor lignin/poly (propylene carbonate) composites

In this paper, the black liquor lignin (BL) from pulp and paper industry was chemically modified using formaldehyde to adjust its aggregation structure and dispersion behavior. The properties of the formaldehyde-modified black liquor lignin (BLF) were measured by Fourier transform infrared spectroscopy, transmission electron microscopy, and differential scanning calorimetry. Results indicated that the BLF had better dispersion ability than BL. Therefore, the BLF as reinforcing fillers was incorporated into poly(propylene carbonate) (PPC) by melt compounding to prepare biodegradable BLF/PPC composites. The tensile properties, microstructure, thermal decomposition properties, and rheological properties of the BLF/PPC composites were investigated. Results showed that the performance of composites was depend on the dispersion of BLF. After adding a small amount of BLF into PPC, the tensile strength, tensile modulus, thermal stability, and processing stability of the composite were significantly improved.     

Preparation and characterization of modified graphite oxide/poly(propylene carbonate) composites by solution intercalation

Modified graphite oxide (MGO)/Poly (propylene carbonate) (PPC) composites with excellent thermal and mechanical properties have been prepared via a facile solution intercalation method. An intercalated structure of MGO/PPC composites was confirmed by X-ray diffraction and scanning electron microscope. The thermal and mechanical properties of MGO/PPC composites were investigated by thermal gravimetric analysis, differential scanning calorimetric, dynamic mechanical analysis, and electronic tensile tester. Due to the nanometer-sized dispersion of layered graphite in PPC matrix and the strong interfacial interaction between MGO and PPC, the prepared MGO/PPC composites exhibit improved thermal and mechanical properties in comparison with pure PPC. Compared with pure PPC, the MGO/PPC composites show the highest thermal stability and the T_g is 13.8 °C higher than that of pure PPC, while the tensile strength (29.51 MPa) shows about 2 times higher than that of pure PPC when only 3.0 wt.% MGO is incorporated. These results indicate that this approach is an efficient method to improve the properties of PPC.     

Improved mechanical property and biocompatibility of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) for blood vessel tissue engineering by blending with poly(propylene carbonate)

Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and poly(propylene carbonate) (PPC) were blended by solvent casting method into films at various weight ratios in order to obtain materials with properties more suitable for blood vessel tissue engineering than pure PHBHHx alone. FTIR and XRD analysis indicated the crystal structure of PHBHHx was not altered but the crystallinity was reduced by the interfusion of PPC. Mechanical properties of the films were improved significantly by blending with PPC. A lower elastic modulus and a higher elongation at break were obtained with the increase of PPC content. Wettability, fibronectin adsorption and adhesion of rabbit aorta smooth muscle cells (RaSMCs) on blend films were similar to or better than that on PHBHHx film. All these results showed promises of PHBHHx/PPC blended materials as scaffold material for blood vessel tissue engineering.     

氯化聚丙撑碳酸酯增容聚丙撑碳酸酯/秸秆粉复合材料的制备及性能

聚丙撑碳酸酯(PPC)是一种新型热塑性生物降解材料,但其热性能及力学性能较差,应用受到限制。以秸秆粉这种农作物副产品作为增强体改性PPC,既可以提高PPC的力学性能同时又可开发利用秸秆资源。氯化聚丙撑碳酸酯(CPPC)是聚丙撑碳酸酯(PPC)经过氯化得到的,对天然纤维表面具有良好的浸润性和粘结性。本文以CPPC为增容剂,通过熔融共混法制备了PPC/秸秆粉复合材料。采用扫描电子显微镜(SEM)、拉伸实验、动态力学性能测试(DMA)及转矩流变仪对复合材料的结构及性能进行了表征,重点考察了CPPC的添加量对复合材料力学和流变性能的影响。结果表明,当CPPC质量分数为1.8%时,可使添加质量分数为30%秸秆粉的PPC复合材料拉伸强度提高38%,模量提高30%。同时,CPPC的引入使复合材料的粘度下降,改善了PPC/秸秆粉复合材料的加工性能。因此,作为增容剂的CPPC为制备高性能PPC/天然纤维复合材料提供了新的解决办法。     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

氨酯化合物对聚碳酸1,2-丙二酯的同时增韧和增强研究

采用非异氰酸酯路线合成了1,6-六亚甲基二氨基甲酸羟异丙酯(BPU),分子量为320.利用熔融共混方法制备了聚碳酸1,2-丙二酯(PPC)/BPU共混物.研究发现BPU与PPC间有较好的相容性,随着BPU含量的增加,共混体系的起始热分解温度(Td.5％)可分别增加24～33℃,共混物韧性也显著提高,断裂伸长率最大可增至...     

Poly(lactic acid)/poly(butylene succinate)/calcium sulfate whiskers biodegradable blends prepared by vane extruder: Analysis of mechanical properties,morphology, and crystallization behavior

Ternary blends of PLA/PBS/CSW with different weight fractions were prepared using a vane extruder. The mechanical properties, morphology, crystallization behavior and thermal stability of the blends were investigated. For the PLA/CSW blend, the tensile strength decreased, the flexural strength and modulus increased compared with pure PLA. For PBS, the addition of CSW had little influence on the mechanical properties. For the ternary blends PLA/PBS/CSW, the tensile strength, flexural strength and modulus decreased compared with pure PLA, while the elongation at break and the impact strength increased significantly. The brittle-ductile transition of the blends took place when the PBS weight fraction reaching 30 wt%. As a soft component in the blends, PBS was beneficial to improve the tensile ductility and the toughness of PLA. SEM measurements reveal that PLA/PBS/CSW blends were immiscible. When the weight fraction of PBS was 50 wt%, significant phase separation was observed, and CSW had preferential location in the PBS phase of the blend. DSC measurement and POM observation reveal that CSW had a heterogeneous nucleation effect on PLA and PBS matrix. The addition of PBS improved the crystallization of PLA and the thermal resistance of the PLA/PBS/CSW blends significantly.