水热法快速合成绿色到近红外发光CdTe量子点

以3-巯基丙酸(MPA)和柠檬酸钠为稳定剂,Na2TeO3为碲源,利用水热法成功制备了从绿色到近红外发射的CdTe量子点,并详细探讨了影响CdTe量子点体系的荧光发射波长和量子产率的因素,如反应前驱液的pH值,反应物的浓度比和反应时间等实验条件.分别用X射线粉末衍射、透射电镜、紫外-可见光谱和荧光光谱对CdTe量子点进行了表征.     

生物相容的高荧光CdTe量子点的合成和表征

用硫普罗宁(tiopronin,TP)作为稳定剂,在水相中合成了荧光发射波长可调的高荧光CdTe量子点。本文详细地研究了稳定剂与Cd之比和pH值等实验条件对CdTe纳米粒子体系的荧光量子产率的影响。在pH=11.3回流2 h,纳米粒子体系在537 nm波长处的荧光量子产率达到了66%。通过控制实验条件,合成了各种尺寸的CdTe量子点,荧光发射光谱在504~602 nm范围连续可调。分别用X射线光电子能谱(XPS)、透射电子显微镜(TEM)、X射线衍射(XRD)、红外吸收光谱(FTIR)表征了CdTe粒子的分散性、形貌和晶型。溶血实验显示,这些由硫普罗宁稳定的CdTe量子点几乎不发生溶血作用(溶血率低于5%),具有良好的生物相容性。     

硫脲修饰法制备高发光性能CdTe量子点

通过巯基水解制备了具有优异荧光特性的碲化镉量子点. 详细研究前驱体镉离子与巯基丙酸(MPA)摩尔比、镉离子浓度等制备条件对大尺寸、高量子产率的亲水性碲化镉量子点光学性能的影响. 在不同的水热生长时间下, 可制备出荧光发射峰位于485-660 nm范围内的不同尺寸的碲化镉水溶性量子点, 荧光发射峰半高宽控制在40-75 nm之间, 量子点的最高量子产率(QY)达到了45%. 并利用硫脲缓慢水解和光解释放自由硫离子, 修饰碲化镉表面, 检测修饰后的量子点在12天内光学性能的变化情况. 通过考察硫脲用量对量子点修饰效果, 发现当n(CdTe)/n(thiourea)=1:4(量子点浓度以镉离子浓度计)时, 硫脲对发射峰为505 nm的碲化镉量子点修饰效果最为理想, 量子点荧光强度加强了5倍, 量子产率达到68.3%.     

水溶性CdTe量子点的合成及影响因素研究

本文以巯基乙酸(TGA)为稳定剂,在水相中合成了高荧光CdTe量子点.其荧光发射波长在507 ～ 628nm范围内可调,最窄半峰宽37 nm,粒径约3.4nm,量子产率达42.1％.本实验在固定前躯体配比不变的情况下,考察了前躯体中镉离子的浓度、pH及回流时间对CdTe生长的影响.并用透射电子显微镜(TEM),荧光分光光度计(FS),X射线衍射仪(XRD)等手段对制备的量子点进行了表征.结果表明:CdTe量子点的尺寸随回流时间而增长;反应的pH对量子点的荧光强度有显著影响;镉离子的浓度越大,量子点的生长速度越快,荧光强度却随之降低.     

颜色可调的高荧光CdTe量子点的水相合成

以亚碲酸钠为碲源,硼氢化钠为还原剂,一步合成了巯基丁二酸(MSA)稳定的CdTe量子点.研究了反应液pH值、镉与碲的摩尔比及镉与巯基丁二酸的摩尔比等实验条件对CdTe量子点体系荧光量子产率的影响,并用荧光光谱、X射线粉末衍射及透射电子显微镜等对其进行了表征.结果表明,CdTe量子点具有闪锌矿结构,形貌呈球状;在pH=1...     

3-巯基异丁酸衍生物对碲化镉量子点水相合成的影响

为探索适宜制备粒径分布窄、荧光量子产率高、发光区域在红光至近红外光区段的量子点的巯基酸的条件, 我们研究了三类3-巯基异丁酸(MIBA)衍生物在以亚碲酸钠为碲源的水相法水热制备CdTe量子点中的影响. 这三类衍生物包括设计合成的主链亲水性衍生物3-巯基异丁酰甘氨酸(MIBGly)、3-巯基异丁酰-3-氨基丙酸(MIBAPA)和3-巯基异丁酰天冬氨酸(MIBAsp), 支链亲水性衍生物N-乙酰基半胱氨酸(ACys)和支链疏水性衍生物3-巯基-2-甲基丁酸(MMBA)和3-巯基-2,2-二甲基丙酸(MDMPA). 以这三类MIBA 衍生物为修饰剂时,CdTe量子点均能够保持MIBA体系较窄的荧光半峰宽. 采用亲水性的MIBA衍生物(MIBGly、MIBAPA、MIBAsp和ACys)比采用疏水性的MIBA衍生物(MMBA和MDMPA)更有利于制备发射波长较长的量子点. 采用支链亲水性的MIBA衍生物((ACys)比采用主链亲水性的MIBA衍生物(MIBGly、MIBAPA和MIBAsp)更容易获得高荧光量子产率的量子点.     

电化学法合成强荧光CdTe量子点

采用电化学方法产生的H2Te为碲源(Te2-),快速合成了水溶性强荧光的CdTe量子点.该方法具有操作简单、安全、快速廉价和可大量制备等优点.合成过程中考察了合成温度,pH值和配体比例对制备CdTe量子点的影响.在最优化的实验条件下,电化学方法合成的巯基丙酸配位的CdTe荧光量子产率可达到55％;通过紫外可见光谱(UV...     

基于CdTe量子点内滤效应同步荧光猝灭法测定四环素

以巯基丙酸作为稳定剂制备CdTe量子点,发现CdTe量子点的激发光谱与四环素的吸收光谱有较好重叠,满足发生内滤效应的条件。据此以四环素为吸光体、CdTe量子点为荧光体构建内滤效应荧光传感体系,从而建立一种测定四环素含量的同步荧光猝灭法。实验结果表明,当固定波长差为220 nm时,CdTe量子点的同步荧光最大发射波长为297 nm。在最佳实验条件下,四环素浓度在1.0×10-6~1.0×10-5mol·L-1范围内与体系同步荧光强度呈良好的线性关系,相关系数和检出限分别为0.999和2.5×10-8mol·L-1。该方法灵敏度高、选择性好,应用于牛奶样品中四环素的检测,加标回收率为97.0%~104.3%。     

CdTe量子点对胰凝乳蛋白酶的荧光标记

用巯基丙酸作为表面修饰剂在水相中制备了稳定的CdTe纳米量子点.利用量子点外层包被的巯基丙酸上的羧基,实现了量子点与胰凝乳蛋白酶的直接偶联.偶联后溶液的吸光度值略有增大而吸收峰位不变,同时荧光强度明显增强,荧光发射峰位稍有蓝移.通过荧光发射光谱确定了CdTe量子点与胰凝乳蛋白酶偶联的最佳反应条件为:pH 9.0,反应温度37℃,反应时间1.5 h.重点考察了NaCl浓度和胰凝乳蛋白酶浓度对量子点与胰凝乳蛋白酶偶联产物荧光强度的影响.     

不同环境因素对水热法合成碲化镉量子点的影响

对比了不同巯基稳定剂和前体浓度对水热环境CdTe量子点的生长过程和光物理性质的影响。结果表明,巯基丙酸与镉前体的结合能力较强,一定程度上减小了前体溶液中镉的浓度,故CdTe量子点生长速率较慢;空间位阻较大的硫普罗宁与镉前体的结合相对较弱,因此导致CdTe量子点生长较快。巯基丙酸有利于制备发光波长较短的高荧光强度CdTe 量子点,而硫普罗宁有利于制备发光波长较长的高荧光强度CdTe量子点。前体浓度对CdTe量子点的生长速率和光物理性质的影响不明显。在上述实验结果基础上,考察了水溶性乙酸钠和聚丙烯酸钠电解质对水热环境中CdTe量子点的生长过程和光物理性质的影响。结果表明,添加乙酸钠后可提高CdTe量子点的生长速率,进而导致CdTe量子点的表面重构和钝化能力下降,使荧光强度降低;聚丙烯酸钠对镉单体独特的固定作用导致CdTe量子点生长缓慢,尺寸集中化受限,钝化能力降低,使荧光强度下降更加明显。     

Luminescent properties of water-soluble denatured bovine serum albumin-coated CdTe quantum dots

Chemically reduced bovine serum albumin (BSA) has been used to modify the surface of water-soluble CdTe quantum dots (QDs). It is demonstrated that the denatured BSA (dBSA) can be conjugated to the surface of CdTe QDs and thereby efficiently improve the chemical stability and the photoluminescence quantum yield (PL QY) of the QDs. It is inferred that a shell-like complex structure CdTe(x)(dBSA)(1-x) will form on the surface of the CdTe "core", resulting in the enhancement of PL intensity and the blue shift of the PL peak. This study of the effects of pH and dBSA concentration on optical properties of dBSA-coated QDs suggests that, at pH 6-9, the solution of dBSA-coated CdTe QDs can keep substantial stability and fluorescent brightness, whereas further increase of pH value leads to a dramatic decrease in PL QY and chemical stability. On the other hand, too high or too low initial dBSA concentration in the QD solution results in a decrease of PL QY for dBSA-coated CdTe QDs. This study provides a new approach of preparing stable water-soluble QDs with high PL QY and controllable luminescent colors for biological labeling applications.     

Effect of CdS Interlayer on Properties of CdTe Based Quantum Dots

Highly luminescent thioglycolic acid-capped CdTe-based core/shell quantum dots (QDs) were synthesized through encapsulating CdTe QDs in various inorganic shells including CdS, ZnS and CdZnS. CdTe/CdS core/shell QDs exhibited a significant redshift of emission peaks (a maximum emission peak of 652 nm for the core/shell QDs and 575 nm for CdTe cores) with increasing shell thickness. In contrast, the redshift of photoluminescence (PL) peak wavelength of CdTe/ZnS QDs was less than 15 nm. The PL peak wavelengths of the core/shell QDs depended strongly on core size and shell thickness. The PL quantum yields (QYs) of the CdTe/CdS core/shell QDs are up to 67 % while that of CdTe/ZnS core/shell QDs is 45 %. A composite CdZnS shell made CdTe cores a high PL QY up to 51 % and broadly adjusted PL spectra (a maximum PL peak wavelength of 664 nm). The epitaxial growth of the shell was confirmed by X-ray powder diffraction analysis and luminescence decay experiments. Because of high PL QYs, tunable PL spectra, and low toxicity from a ZnS surface layer, CdTe/CdZnS core/shell QDs will be great potential for bioapplications.     

表面修饰CdTe量子点的合成及其光学特性

在水相中合成高发光性能的CdTe量子点,研究以巯基乙酸(TGA)为稳定剂对CdTe表面进行修饰,制备在水中分散性良好的纳米晶,通过对CdTe量子点合成反应条件的摸索,掌握了其合成的反应规律.同时用紫外分光光度计、荧光分光光度计和透射电子显微镜对其进行了表征.结果表明,回流时间、n(Cd²⁺):n(HTe^-)、反应物浓度、TGA用量、反应体系pH值,对纳米晶的光学性质具有显著影响.回流2 h制得的CdTe纳米粒子直径约为5 nm,其发射峰窄且对称,表现出良好稳定的光学性质.     

Modification of CdTe quantum dots as temperature-insensitive bioprobes

CdTe quantum dots (QDs) were synthesized in aqueous solution with 3-mercaptopropionic acid (MPA) as the stabilizer. The photoluminescence (PL) of CdTe QDs (3.5nm) is found to be temperature-dependent: as the temperature arising from 278K to 323K, the PL intensity declines to 50.2% of its original and PL emission peak shows obvious red-shift ( approximately 7nm). After modification of the QDs surface with denatured ovalbumin, the PL is more temperature-insensitive than before. The PL intensity retains more than 70% of its original and the emission peak shows less red-shift ( approximately 2nm). Moreover, it is found that the PL intensity and wavelength of denatured ovalbumin coated CdTe QDs are reversible during heating (323K)-cooling (278K) cycles. All the studies provide an important theoretical basis for searching temperature-insensitive bioprobes.     

Synthesis of CdTe Quantum Dots with Tunable Photoluminescence Using Tellurium Dioxide as Tellurium Source

A simple and convenient method has been developed for synthesis of water‐soluble CdTe quantum dots (QDs) under ambient atmospheric conditions. In contrast to the traditional aqueous synthesis, green to red emitting CdTe QDs were prepared by using TeO₂ to replace Te or Al₂Te₃ as tellurium source in this method. The influences of experimental variables, including pH value, 3‐mercaptopropionic acid (MPA)/Cd and Te/Cd molar ratios, on the emission peak and photoluminescence (PL) quantum yield (QY) of the obtained CdTe QDs have been systematically investigated. Experimental results indicate that green to red emitting CdTe QDs with a maximum photoluminescence quantum yield of 35.4% can be prepared at pH 11.3 and n_(Cd):n_(Te):n_(MPA)=1:0.1:1.7.     

Synthesis of CdTe colloidal quantum dots (QDs) in water

The comparison of growth processes and fluorescent properties of CdTe semiconductor quantum dots (QDs) that are synthesized in water with different modifiers are discussed in this paper. The samples are characterized through ultraviolet-visible spectra (UV-Vis), photoluminescence spectra (PL) and zeta potential. The results show that when the reaction time is prolonged for the same modifier, the ultraviolet absorption peak and fluorescent emission peak present obvious red shifts and the diameters of the QDs continuously increase. With the same reaction time but different modifiers, QDs with different diameters can be gained. The average full width at half maximum of the photoluminescence spectra is about 50 nm which shows that the monodispersity is quite good. Under the best reaction conditions, the highest quantum yield (QY) can be attained by using thioglycollic acid (TGA) as modifier when the reaction time is 240 min. The zeta potential is influenced by the modifier and pH. __________ Translated from Journal of Shanghai Jiao Tong University, 2007, 41(10): 1690–1694 [译自: 上海交通大学学报]     

不同环境因子作用下水溶性CdTe量子点的生长动力学研究

以硫普罗宁为稳定剂,水热法制备了水溶性CdTe量子点,系统研究了回流时间、反应物配比、pH值、反应温度和电解质种类等环境因子对量子点生长动力学及光物理性质的影响。结果表明,溶液的pH值及反应物配比对CdTe量子点的光物理性质均有重要影响。优化条件后,回流5 h可得到发射峰位于550 nm的CdTe量子点,其荧光量子效率高达52%;在氯化钠作用下,量子点生长加快,即高浓度氯化钠会减弱溶液中粒子间静电排斥,促进离子扩散,有利于量子点的生长;添加苯磺酸钠会抑制量子点的生长,有利于制备高荧光量子效率的小尺寸CdTe量子点。     

超声电化学快速制备近红外CdTe量子点与细胞成像

针对当前水溶性量子点合成路线复杂、量子产率低的现状, 在无需N₂保护的条件下, 采用简便的超声电化学方法快速合成了CdTe量子点前驱体;并对不同条件下制得的前驱体加热回流, 得到水溶性、高质量的近红外CdTe量子点。产物的形貌、结构和组成通过高分辨透射电子显微镜(HRTEM)、X-射线粉末衍射(XRD)等手段进行了表征。考察了超声电化学参数和回流条件对量子点荧光性质的影响。通过控制电流脉冲宽度、反应时间、反应温度等参数, 实现了CdTe量子点前驱体的可控制备;通过调节加热回流条件得到不同荧光发射波长的量子点;选用602 nm近红外发射波长的CdTe量子点标记了子宫颈癌细胞(Hela), 并采用共聚焦技术实现了肿瘤细胞的显微成像观察。和传统的量子点合成方法相比, 超声电化学方法具有合成路线简单、参数易调可控的特点;为高品质量子点的快速制备提供了新的思路, 拓展了超声电化学在纳米材料制备领域的应用。