The influence of water–organic solvent composition on the morphology and luminescent properties of CdS nanoparticles obtained by chemical precipitation

Cadmium sulfide (CdS) nanoparticles have been obtained by chemical precipitation onto the surface of single-crystalline silicon from an aqueous solution of ammonia, cadmium chloride (CdCl₂), and thiourea, as well as from water–DMSO and water–DMF mixtures with the same concentrations of the reagents. According to data of atomic force microscopy, the samples obtained from the aqueous solution consist of individual nanoparticles and agglomerates thereof with sizes of no larger than 1 µm. Materials obtained from the water–organic mixtures are distinguished by the aggregation of CdS nanoparticles into threadlike chains. The length of the formed curved chains and the size of CdS nanoparticles composing them depend on the nature and amount of an organic component of a mixture. Atomic force microscopy, transmission electron microscopy, and photoluminescence spectroscopy data have shown that the average size of CdS nanoparticles is 2–2.5 nm depending on solvent composition.     

Synthesis and characterization of CdS nanoparticles prepared by precipitation in the presence of span 20 as surfactant

Cadmium sulfide nanoparticles with average size of ≈16 nm have been synthesized using chemical precipitation reaction of CdCl₂ and Na₂S in the presence of nonionic surfactant stabilized reverse emulsions. Sorbian monolaurate (Span 20) is used for the stabilization of emulsions. The influence of Span 20 on controlling the size and properties of CdS nanoparticles were studied. The obtained CdS nanoparticles were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Energy-dispersive x-ray (EDX), and X-ray diffraction (XRD). The optical properties of CdS nanoparticles are investigated systematically by UV-visible absorption spectroscopy. The blue shift in the absorption region and increase in the bandgap to the larger value (2.77 eV) are attributed to the nanosize of the obtained particles.     

Formation of monodispersed PVP-capped ZnS and CdS nanocrystals under microwave irradiation

Poly (N-vinyl-2-pyrrolidone) (PVP)-capped ZnS, CdS nanoparticles were prepared by a microwave method from Zn(Ac)₂ or Cd(Ac)₂ and thiourea in N,N-dimethylformamide (DMF) solution. The reaction process was monitored by the temporal evolution of the absorption spectrum. With PVP as stabilizer, monodispersed semiconductor nanoparticles, which showed high quantum size effect, have been obtained. Further study showed that the microwave irradiation could influence selectively the nucleation and growing rates of different semiconductor nanoparticles.     

巯萘剂表面修饰的CdS纳米微粒的合成及发光特性

用疏萘剂(TN)作为表面修饰剂,在甲醇溶液中合成了CdS/TN纳米微粒,用TEM测得纳米微粒呈球形,其粒径约10nm,吸收光谱和荧光光谱研究表明,[S^2-]/[TN]浓度比、TN和镉离子的浓度对CdS/TN纳米微粒的粒径及发光特性具有显著影响,且随着条件的改变,CdS/TN纳米微粒的发射波长红移100nm,表现出明显的量子尺寸特性.XPS显示所制得表面修饰纳米微粒的核为CdS.     

微波固相反应制备CdS纳米粒子

硫化镉是一种重要的半导体材料,在太阳能转化、非线形光学、光电子化学电池和光催化方面具有广泛的应用[1,2]。近十年以来,人们已经使用了许多的方法来制备纳米硫化镉[3~7]。由于微波能同时促进吸热反应和放热反应,对化学反应具有催化作用,可降低反应的温度,从而为化学反应创造     

Stability and optical properties of dispersions of CdS,ZnS, and Ag<Subscript>2</Subscript>S nanoparticles synthesized in microemulsion

CdS, ZnS, and Ag₂S nanoparticles have been synthesized in microemulsion. The synthesis of nanoparticles depend on the composition of the reaction medium and on the proportions of the precursors. The phase diagram for sedimentation stable dispersion of the nanoparticles synthesized in microemulsion has been determined. The region of the stable nanoparticle dispersion is much smaller than the region of the inverse microemulsion in the n-heptane-AOT-H₂O system. The UV-vis absorption and photoluminescence spectra of the CdS, ZnS, and Ag₂S nanoparticles have been investigated. The size of the nanoparticles increases with an increase in droplet size in the microemulsion, and this shifts the exciton peaks.     

Characterization of CdS nanoparticles in solutions of P(TFE-co-PVDF-co-Prop)/N,N-dimethylformamide

We report in here the preparation of CdS nanoparticles (Q-CdS) in N,N-dimethylformamide (DMF) and poly(tetrafluoroethylene-co-vinylidenefluoride-co-propylene) (PTFE-co-PVDF-co-Prop) by reaction of cadmium acetate and thiourea at room temperature. The formation and size evolution of Q-CdS particles were followed by optical absorption spectroscopy as a function of the aging process of the solutions. The obtained results indicated that not only the Q-CdS particles were more stable in DMF than in aqueous solutions, probably due to the interaction with the CHNO group, but also they were formed in smaller sizes. The particle size obtained in DMF was estimated in 4-6 nm against 10-20 nm in aqueous solution. The results also showed that the velocity of Q-CdS formation is lower when the reaction was carried out in PTFE-co-PVDF-co-Prop dissolved in DMF. The Q-CdS particles formed in this system were also less stable than in pure DMF, probably due to the interaction of the CHNO fragment and CF₂ of polymer chain or phase segregation.     

Analysis of the local atomic structure of quantum dots of the CdS family

The microwave synthesis of quantum dots based on CdS has been performed, the temperature (T 180°C and 150°C) and synthesis duration (10 min and 5 min) have been varied. The analysis of the peak broadening in X-ray diffraction has shown that the average particle size in the synthesized samples is 10.02 nm for the CdS _{T = 180°C} sample and 5.22 nm for the CdS _{T = 150°C} sample. For both synthesis temperatures particles of sphalerite phase are formed but the sample CdS _{T = 180°C} contained some impurity of wurtzite phase too. CdK-XANES spectra in the standard samples and quantum dots have been recorded using a Rigaku R-XAS X-ray absorption laboratory spectrometer. The theoretical analysis of the CdK-XANES spectra of bulk samples of CdS and CdS nanoparticles has been performed. It has been shown that the theoretical difference spectra between bulk CdS and CdS with decreased lattice parameters demonstrate the same tendency as the experimental difference spectra between bulk CdS and the quantum dot samples under study. It has been shown that the theoretical CdK-edge HERFD-XANES spectrum in CdS demonstrates considerably more detailed structure pointed to the need of the analysis of experimental CdK-edge HERFDXANES spectra to pick out more precise information on local atomic structure parameters of small semiconducting quantum dots.     

Simple and low temperature preparation and characterization of CdS nanoparticles as a highly efficient photocatalyst in presence of a low-cost ionic liquid

A simple and low temperature method is proposed for preparation of CdS nanoparticles in presence of 1-ethyl-3-methylimidazolium ethyl sulfate, [EMIM] [EtSO₄], a room-temperature ionic liquid (RTIL). The powder X-ray diffraction (XRD) studies display that the products are excellently crystallized in the form of cubic structure and size of the nanparticles prepared in presence of the RTIL is smaller than that prepared in water. Energy dispersive X-ray spectroscopy (EDX) investigations reveal that the products are very pure and nearly stoichiometric. The results obtained by scanning electron microscopy (SEM) demonstrate that the CdS nanoparticles prepared in presence of the RTIL have lower tendency for aggregation relative to the prepared sample in water. Diffuse reflectance spectra (DRS) of the product prepared in the neat RTIL, shows 1.52 eV blue shift relative to bulk CdS, which can be attributed to quantum confinement effect of the CdS nanoparticles. A possible formation mechanism for CdS nanoparticles in presence of the RTIL is presented. Photocatalytic activity of the CdS nanoparticles towards photodegradation of methylene blue (MB) using UV and visible lights was performed. The results demonstrate that observed firstorder rate constant for photodegradation of MB on CdS nanoparticles prepared in the neat RTIL are about 20 and 6 times greater than the prepared sample in water using visible and UV lights, respectively.     

Studies on optical absorption and structural properties of Fe doped CdS quantum dots

Fe doped CdS quantum dots have been prepared using simple precursors by chemical precipitation technique. Fe doped CdS quantum dots have been synthesized by mixing cadmium nitrate, sodium sulfide and adding Fe under suitable conditions. X-ray diffraction analysis reveals that undoped and Fe doped CdS crystallizes in hexagonal structure. The lattice constants of Fe doped CdS nanoparticles decreased slightly with incorporation of Fe and no secondary phase was observed. The average grain size of the nanoparticles is found to lie in the range of 2.8–4.2 nm. HRTEM results show that undoped and 3.75% Fe doped CdS nanoparticles exhibit a uniform size distribution and average size of the nanoparticles is about 2–3 nm. Raman spectra show that 1LO and 2LO peaks of the Fe doped CdS samples are slightly red shifted compared with those of undoped CdS. Optical absorption spectra of Fe doped CdS nanoparticles exhibited red shift.     

Mechanism of the formation of photosensitive nanostructured TiO<Subscript>2</Subscript> with low content of CdS nanoparticles

A method for synthesizing a CdS/TiO₂ composite material, active in the visible region, was described. The CdS/TiO₂ composite was obtained by the sol–gel synthesis of nanostructured TiO₂ in a medium of a stable colloidal solution of CdS nanoparticles. The TiO₂ matrix produced by the sol–gel process is amorphous and contains a nanocrystalline anatase phase, the content of which depends on the Ti(OBu)₄ hydrolysis rate. The content of CdS nanoparticles forming in the colloidal solution and participating in the TiO₂ matrix sensitization is determined by the initial CdS: Ti(OBu)₄ ratio. Although the content of CdS nanoparticles in the composite is low (no more than 3 wt %), the composite demonstrates catalytic activity in the visible region, thus proving the possibility of reducing the content of toxic CdS nanoparticles in the TiO₂ matrix without decreasing the photosensitivity of the CdS/TiO₂ composite.     

Synthesis, structural and photocatalytic studies of Mn-doped CdS nanoparticles

Mn-doped CdS nanoparticles (Cd_1?x Mn _x S; where x = 0.00–0.10) were synthesized by a chemical precipitation method. The synthesized products were characterized by X-ray diffraction (XRD), scanning electron microscope, transmission electron microscope (TEM), and UV–Vis spectrometer. The XRD and TEM measurements show that the size of crystallites is in the range of 10–40 nm. Optical measurements indicated a red shift in the absorption band edge upon Mn doping. The direct allowed band gaps of undoped and Mn-doped CdS nanoparticles measured by UV–Vis spectrometer were 2.3 and 2.4 eV at 400 °C, respectively. Photocatalytic activities of CdS and Mn-doped CdS were evaluated by irradiating the solution to ultraviolet light and taking methyl orange (MO) as organic dye. It was found that 5 mol% Mn-doped CdS bleaches MO much faster than undoped CdS upon its exposure to the ultraviolet light. The experiment demonstrated that the photo-degradation efficiency of 5 mol% Mn-doped CdS was significantly higher than that of undoped CdS.     

Studies of nanoparticulate cadmium sulfide in amphiphilic polymaleic acid octadecanol ester Langmuir-Blodgett films

The reversed micelles of CdS nanoparticles capped with oligomer–polymaleic acid octadecanol ester (PMAO) were synthesized by a colloid chemical method in an aqueous system. The chemical ratio of PMAO between the carboxylic group and the hydrocarbon chain was controlled to 1.5 : 1. The PMAO-capped CdS nanoparticles were transferred on to CaF₂ and Si substrates by the Langmuir–Blodgett (LB) technique. Surface pressure–area isotherms indicated that PMAO-capped CdS nanoparticles could form a stable monolayer on the water subphase. The measurement of FTIR and small angle X-ray diffraction showed that the reversed micelles of PMAO-capped CdS nanoparticles were formed with a uniform size and order in LB films. The photoluminescence properties of PMAO-capped CdS both in the solution and in the LB film indicated that the photoluminescence peaks of reversed micelles obviously changed as a result of the energy transfer from PMAO to CdS and the interaction between clusters.     

Synthesis of CdS, ZnS and Ag2S nanoparticles stabilized by sodium bis(2-ethylhexyl)sulfosuccinate and polyoxyethylenesorbitan monooleate in aqueous medium

The effect of synthesis conditions (molar ratio between precursors, concentration of surfactants, synthesis temperature) on the size of CdS, ZnS and Ag₂S nanoparticles (NPs) stabilized by sodium bis(2-ethylhexyl)succinate and polyoxyethylenesorbitan monooleate was studied. It was established that stabilization by polyoxyethylenesorbitan results in formation of smaller NPs (～8 nm) as compared to that in the presence of sodium bis(2-ethylhexyl)sulfosuccinate (14–60 nm), which is due to the difference between the adsorption rates of these surfactants onto the surface of synthesized NPs. The resulting aqueous dispersions of CdS, ZnS and Ag₂S NPs exhibit long-term stability to sedimentation. The nanoparticle size increases insignificantly with temperature increasing to 65–70°C and rises abruptly at higher temperatures. The increase in the ratio between concentrations of precursors (sulfide and metal ions) also results in an increase in NP size, allowing one to synthesize nanoparticles of prescribed sizes. The optical properties of the resulting nanoparticles were studied. The positions of the exciton peaks and the luminescence intensity peaks of the dispersions of synthesized CdS and ZnS NPs were determined.     

Construction of inorganic nanoparticles by micro-nano-porous structure of cellulose matrix

In our previous work, the CdS nanoparticles/cellulose films exhibited significantly high photocatalytic H₂ production efficiency under visible light irradiation than the ordinary CdS photocatalyst. In present paper, the CdS nanoparticles were synthesized in situ in pores of the regenerated cellulose substrate and the porous structure of cellulose, formation of the CdS nanoparticles and interactions between CdS and cellulose matrix in the composite films were investigated deeply. The experimental results indicated that the micro-nano-porous structure of the cellulose matrix could be used easily to create inorganic nanoparticles, which supplied not only cavities for the formation of nanoparticles, but also a shell (semi-stiff cellulose molecules support the pore wall) to protect their nano-structure. When the cellulose films with porous structure at wet state were immersed into inorganic ions solution, the ions interacted immediately with the –OH groups of cellulose, and then transformed into inorganic composite via another treatment, finally inorganic nanoparticles formed during the dry. The pore size of the cellulose matrix decreased from 180 nm (at wet state) to about 18 nm (at dry state), leading to the formation of nanoparticles. The results revealed that the CdS nanoparticles with a mean particle diameter about 6 nm were dispersed well, and were immobilized tightly in the cellulose matrix, resulting in a portable photocatalyst with high efficiency for photocatalytic for H₂ evolution. This is simple and “green” pathway to prepare the organic–inorganic hybrid materials.     

Controllable incorporation of CdS nanoparticles into TiO<Subscript>2</Subscript> nanotubes for highly enhancing the photocatalytic response to visible light

A constant current electrochemical deposition was employed to incorporate CdS nanoparticles into the TiO₂ nanotube arrays (TiO₂NTs). The size and amount of CdS nanoparticles in TiO₂NTs (CdS@TiO₂NTs) were controllable via modulating current, deposition time and electrolyte concentration. It was revealed, from the scanning electron microscopy (SEM) images and X-ray photoelectron spectroscopy (XPS) in depth profile, that CdS nanoparticles were filled into TiO₂ nanotubes. A shift of the absorption edge toward the visible region under the optimal electrodeposition condition was observed with the diffuse reflectance spectroscopy (DRS). A 5-fold enhancement in the photocurrent spectrum for TiO₂NTs was observed and the photocurrent response range was significantly extended into the visible region because of the CdS incorporation. Compared with pure TiO₂NTs, under a visible light irradiation, CdS@TiO₂NTs exhibited a 3.5-fold improvement of photocatalytic activity, which was demonstrated by the photocatalytic decomposition of Rhodamine B (RhB).     

Kinetic effect in the size-control of CdS nanoparticles

A new method of size control for CdS nanoparticles, called common cation coprecipitation, is reported. In the course of coprecipitation, both CdS and CdSt_2(cadmium stearate) formations are diffusion-controlled and their rates are quite different. The size of CdS nanoparticles depends on the ratio of initial concentrations of S~(2-) to St~- (stearate ion). Characterized by UV-Vis absorption, XRD, TEM, fluorescence and XPS, the results obtained show that the coprecipitate is a composite, i. e. CdS particle inserts in the CdSt_2 molecular layers to form a sandwich-like structure. The method reported for size control of CdS nanoparticles might be called kinetic self-assembling.     

Preparation of colloidal CdSe and CdS/CdSe nanoparticles from sodium selenosulfate in aqueous polymers solutions

Cadmium selenide nanoparticles formation at the interaction between CdCl2 and Na2SeSO3 in aqueous solutions of sodium polyphosphate and gelatin has been studied. Structural and optical properties of CdSe nanoparticles have been characterized. It has been shown that the temperature and the ratio of reagents concentrations are the basic parameters, controlling the size of CdSe nanoparticles. Photocatalytic activity of CdS nanoparticles in Na2SeSO3 reduction has been found and investigated; structural and optical properties of binary CdS/CdSe nanoparticles have been characterized. This photoreaction, when carried out in the presence of CdCl2, results in the formation of composite CdS/CdSe nanoparticles. It has been shown that slow interaction of adsorbed selenosulfate with surface-trapped CdS conduction band electrons is the limiting stage of the photocatalytic reaction.     

Improving the contact properties of CdS-decorated TiO<Subscript>2</Subscript> nanotube arrays using an electrochemical/thermal/chemical approach

Decoration of TiO₂ nanotube films (TiO₂ nanotube arrays (TNAs)) with CdS nanoparticles has been pursued for a broad range of applications that goes from solar cells to biological sensors. In most synthesis methods, the scale-up of devices has been challenging due to the poor contact at the chalcogenide/oxide interface. In this work, we validate the electrochemical/thermal/chemical route as a superior strategy to sensitize TNAs with CdS nanoparticles when compared with conventional methods. The process consisted of (i) electrodeposition of cadmium on TNAs to ensure strong bonding between TiO₂ and Cd precursor particles, (ii) air annealing of Cd-decorated TNAs to thermally oxidize cadmium to cadmium oxide, and (iii) total sulfurization of cadmium oxide to obtain CdS in an hexagonal phase matching that of TNAs. X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) analyses indicated the complete transformation of cadmium precursor particles into CdS and a good surface coverage of the internal/external walls of TNAs. When compared to samples prepared by successive ionic layer adsorption and reaction (SILAR), electrochemical impedance spectroscopy data revealed the improvement of the electrical properties of the TNA matrix due to the sulfurization process and a lower contact resistance at the CdS/TNA interface. These improvements explain the superior photoelectrochemical response of CdS/TNA photoelectrodes obtained by the electrochemical/thermal/chemical route.     

The influence of DMSO on the formation and photoelectrochemical properties of CdS thin films by electrodeposition method

The homodispersed CdS nanoparticles were prepared on Sn-doped indium oxide substrates (ITO) to form smooth and uniform CdS thin films by electrodeposition method from a dimethyl sulfoxide (DMSO) solution containing cadmium chloride and sulfur. The structure and morphologies of samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and atomic force microscopy. The results indicate that DMSO played an important role in formation of CdS nanofilms by affecting the nucleation and growth of the CdS nanoparticles. So, a DMSO-assisted growth process was proposed as a plausible mechanism for the formation of smooth and uniform CdS nanofilms. According to the photoelectrochemical test, the CdS thin film prepared in 30 % DMSO + 70 % H₂O system exhibited maximum photocurrent and open circuit potentials. This is because the deposited CdS nanoparticles had better dispersity on ITO, which facilitated the propagation and kinetic separation of photogenerated charges.