具有三维贯通多级孔道结构大孔氧化铝的制备与表征

采用铝溶胶晶种引入、结合相分离的方法制备了具有三维贯通多级孔道结构的大孔氧化铝材料。采用扫描电镜（SEM）、X射线衍射（XRD）、N₂吸附-脱附、压汞、核磁共振波谱（NMR）等测试方法对所得材料进行了表征。结果表明,该氧化铝材料具有200-600 nm的均匀分布且贯通的连续大孔孔道,经550℃焙烧即可得到结晶态γ-氧化铝。大孔氧化铝比表面积达到366 m²/g,具有以5 nm及400 nm为中心的较为集中的介孔-大孔多级孔道分布。焙烧后的样品中,铝具有四、六两种配位状态。制备过程中,聚环氧乙烷（PEO）作为诱导剂引发固-液两相分离,形成具有三维贯通多级孔道结构大孔氧化铝,而凝胶中引入铝溶胶时,AlOOH晶粒与铝交联水合物均相伴生,在凝胶过程诱导铝交联水合物转变为AlOOH,最终使大孔氧化铝在较低的焙烧温度即可转化为γ-氧化铝。     

活性氧化铝孔结构的控制

研究了pH值交替变动、水热处理以及表面活性剂对活性氧化铝孔结构的影响。实验结果表明：pH值交替变动可以制备出结晶度高，晶粒大且均匀的拟薄水铝石；水热处理有利于氧化铝结构内铝原子迁移，促进晶粒进一步增长；而表面活性剂能够插入拟薄水铝石层间，减少焙烧过程中层间坍塌和毛细孔收缩，从而有效调控氧化铝孔结构。其中pH值交替变动和水热处理使氧化铝微孔分布向大孔方向迁移，比表面降低；加入表面活性剂使氧化铝微孔分布向小孔方向迁移，比表面增加，制备出了低比表面(≤150 m²·g^-1)和高比表面(≥250 m²·g^-1)的大孔容氧化铝载体。同时对铝原子的配位情况进行考察，发现铝原子主要以四配位和六配位状态存在，加入表面活性剂和水热处理能显著改变四配位铝和六配位铝的比值。     

溶胶凝胶法制备中孔分布集中的氧化铝催化材料

报道一种新的中孔氧化铝催化材料的制备方法.通过该方法可以以无机盐和SB粉为原料经过沉淀、解胶的过程首先制得稳定的铝溶胶,然后经过干燥、焙烧得到中孔氧化铝催化材料.用BET,TEM,DTA和XRD等方法对该中孔氧化铝催化材料的基本物理化学性质进行了表征.实验结果表明在不使用模板剂的前提下,通过本文报道的方法能够制得比表面积较大、中孔分布集中的氧化铝材料,并且其孔径分布主要集中在4nm左右.实验结果表明以SB粉为原料制备得到的氧化铝材料具有较好的热稳定性.     

汽车尾气净化器用活性氧化铝的研制

应用一种新的氧化铝制备方法-水合含碳氧化铝热解法, 通过引入模板导向剂和热稳定助剂, 制得了Al2O3纯度≥99.9%, 一次晶粒0.1 μm, 平均粒径0.2～3 μm, BET比表面积148.4 m2*g-1(900 ℃, 1 h焙烧)的活性氧化铝. 该方法所得产品性能稳定, 孔容大, 孔径分布合理, 纯度高. 样品经用户小批量试用认定 其新鲜态、老化后的比表面积和小杂质含量(P, S, Cl, Pb)指标均优于国内同类产品, Al2O3涂层粘结强度、涂层负载量等性能达到国际先进水平.     

碳纳米管负载氧化铝材料的制备及其吸附水中氟离子的研究

采用碳纳米管和硝酸铝制备了碳纳米管负载氧化铝新型除氟材料.X射线衍射检测发现,当焙烧温度低于850℃时,氧化铝为无定形态,当焙烧温度为1050℃时,氧化铝为α形态,扫描电子显微镜观察到碳纳米管与氧化铝均匀掺杂.同时用碳纳米管负载氧化铝复合材料进行水中氟离子的吸附研究,结果表明,该复合材料具有优良的除氟效能.氧化铝负载量为30%、焙烧温度为450℃条件下制备的碳纳米管负载氧化铝复合材料的吸附除氟能力是γ-氧化铝的2.0～3.5倍,与IRA-410聚合树脂的吸附除氟能力相当,适宜pH范围为5.0～9.0,吸附等温线符合Freundlich方程.     

TiO2纳米粒子制备方法对其光催化活性的影响

分别用胶溶法、金属醇盐水解法和低温水解法制备了TiO2纳米粒子;采用XRD和BET技术,测试了TiO2粒子的粒径、晶型及表面积。以庚烷的气相光催化氧化为探针反应,考察了不同方法、不同温度处理的TiO2粒子的光催化活性。结果表明,以胶溶法和金属醇盐水解法制备的TiO2粒子,随焙烧温度的增加TiO2粒子长大,晶型由锐钛矿向金红石型转变,光催化活性降低。用低温水解法,可在低温下制得金红石型TiO2粒子,但其催化活性很低。说明由原料和制备方法所决定的TiO2粒子的物理化学性质,影响其光催化行为。锐钛矿型TiO2粒子催化活性较金红石型TiO2好。这是由于前者的表面羟基含量较高且带隙能较大的缘故。     

三维贯穿大孔氧化铝的孔道改性、表征及转化机制

利用相分离技术制备了非晶三维贯穿大孔氧化铝初始材料,然后通过氨水水热改性处理,使其大孔形态发生了显著改变,孔壁边缘生长有尺寸为50-300 nm的片状聚集体,大孔尺寸由430 nm下降到250 nm,但仍然保持蠕虫状三维贯穿且空间分布均匀的特性。改性后的氧化铝材料经550℃焙烧转化为高结晶度γ氧化铝,比表面积达到331 m²/g,具有8.9 nm及250 nm两种集中的孔径分布,L酸度及抗压强度均有所提高。研究表明,无定形水合羟基铝离子聚合物与氨水发生再水合反应生成薄水铝石中间物,因此,可在较低的焙烧温度下转晶为γ态;大孔孔壁边缘的AlOOH晶粒受NH₄⁺模板诱导作用从里向外重排形成片状聚集体,从而改变了大孔的形态。     

低温苯甲醇醇解法制备高活性锐钛矿型纳米晶TiO2光催化剂

 以TiCl4 为钛源,采用低温苯甲醇醇解法制备了不同粒径及晶相组成的大表面TiO2纳米晶,利用X射线衍射、热重-差热分析、透射电子显微镜、拉曼光谱、紫外-可见漫反射光谱和N2物理吸附等方法考察了焙烧温度和焙烧时间对其晶相组成、晶粒尺寸、比表面积及孔体积等微结构性质的影响,并以苯酚的光催化降解为模型反应评价了样品的光催化活性. 结果表明,未经任何热处理的TiO2样品即为锐钛矿晶相,控制焙烧温度及焙烧时间可进一步调控样品的粒径、比表面积、晶相结构及表面氧缺位浓度. 经400 ℃焙烧3 h制备的纳米晶TiO2具有最佳的光催化活性,其活性比商用Degussa P-25 TiO2更高.     

高比表面积有序介孔氧化铝的制备与表征

采用溶胶-凝胶法以非离子表面活性剂PEO-PPO-PEO三嵌段共聚物F127为模板剂, 以异丙醇铝为铝源, 以异丙醇为溶剂, 成功地制备出比表面积为485 m2/g、孔径分布窄(2~20 nm)、孔容在1.2 cm3/g以上和孔道呈蠕虫状且具有一定有序性的介孔氧化铝. 采用BET, TEM, XRD和TG多种测试技术对产物性能进行了表征. 探讨了水铝比、醇水混合溶液的滴加速度、反应时间、水浴温度、陈化温度及陈化时间等条件对合成的有序介孔氧化铝结构的影响.     

掺钇锆醇盐水解Sol-Gel的物化过程及其机理

醇盐水解法广泛用于金属氧化物溶胶-凝胶的制备．一般，醇盐水解有二种方式，一是通过金属醇盐的完全水解、生成沉淀、继而胶溶形成溶胶；另一种是通过控制水解直接制得溶胶或凝胶．其中，由于醇盐控制水解法成胶容易，胶凝时间可以通过控制参数进行调节，所得胶粒细小均匀，因     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).