LiNi0.8Co0.15Al0.05O2制备过程中聚乙烯吡咯烷酮的加入对其电化学性能的影响

为提高LiNi_(0.8)Co_(0.15)Al_(0.05)O_2(NCA)材料的电化学性能,在NCA材料的制备过程中加入聚乙烯吡咯烷酮(PVP),通过调控所得NCA材料的形貌来提高其电化学性能。所得材料采用X射线衍射仪和扫描电子显微镜进行形貌结构表征,电化学性能经组装成纽扣电池,用电池程控测试仪和电化学工作站进行测试。研究结果表明:由于PVP的空间效应和静电作用,PVP改性的NCA材料拥有更完整的棒状结构、发育出更好的层状结构,电化学储能性能得到较大的提升。在0.1C下,材料的首次放电比容量和充放电效率分别从143.36 mAh·g~(-1)、78.25%提高到了170.24 mAh·g~(-1)、89.20%;在0.2C的实验室条件下循环50次后,容量保持率为94.28%。     

Zr掺杂对正极材料Li(Ni0.9Co0.05Al0.05)O2的电化学性能影响

通过控制结晶法制备类球形Ni_(0.9)Co_(0.05)Al_(0.03)Zr_(0.02)(OH))2前驱体,与LiOH·H_2O均匀混合后,在750℃下于氧气中进行高温焙烧,最终合成正极材料Li(Ni_(0.9)Co_(0.05)Al_(0.05))O_2。扫描电子显微镜(SEM)结果显示前驱体及正极材料具有良好的形貌;X射线衍射(XRD)表明材料具有规整的六方单相层状α-Na FeO_2结构;能谱仪(EDXS)分析表明Zr元素在材料颗粒内部呈均匀分布。合成的Ni_(0.9)Co_(0.05)Al_(0.03)Zr_(0.02)O_2正极材料具有良好的电化学性能,在25℃,2.8~4.3 V充放电条件下,0.2C首次放电比容量为221.5 m Ah·g-1,充放电效率90.3%,2C倍率充放电条件下容量仍达到192.7 m Ah·g-1,100周循环后的容量保持率为92.2%。在55℃,2.8~4.3 V的高温充放电条件下,该材料的0.2C首次放电比容量可达236.2 m Ah·g-1,2C充放电倍率下循环100周容量保持率为85.1%。     

石墨烯修饰改性制备锂离子电池LiFePO4/LiNi0.8Co0.15Al0.05O2复合正极材料及其性能

采用两步干混-球磨方法制备了石墨烯掺杂改性的锂离子电池LiFePO_4/LiNi_(0.8)Co_(0.15)Al_(0.05)O_2复合正极材料,实现LiNi_(0.8)Co_(0.15)Al_(0.05)O_2材料的高容量和高安全性。借助X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、X射线光电子能谱(XPS)以及电化学测试等表征手段对材料的晶体结构、微观形貌和电化学性能进行了较系统的研究。结果表明,石墨烯的存在实现了Li Fe PO4材料在LiNi_(0.8)Co_(0.15)Al_(0.05)O_2材料表面的完全包覆,形成致密的包覆层,进一步抑制LiNi_(0.8)Co_(0.15)Al_(0.05)O_2与电解液之间的副反应,提高活性材料利用率和循环性能。三者之间构成导电网络,加快电子渗透和传输,提高倍率性能。Li Fe PO4质量分数为20%的Li Fe PO4-Graphene/LiNi_(0.8)Co_(0.15)Al_(0.05)O_2样品具有最佳的容量性能和长循环性能,0.1C时放电容量达到202.5 m Ah·g~(-1),3C时放电容量仍然可保持在160.5 m Ah·g~(-1)。50℃在2.8~4.3 V,0.5C下循环100次后,容量保持率为91.9%,优于LiNi_(0.8)Co_(0.15)Al_(0.05)O_2和LiFePO_4/LiNi_(0.8)Co_(0.15)Al_(0.05)O_2样品的72.9%和82.0%。     

水洗和回烧工艺对高镍三元材料LiNi0.88Co0.07Al0.05O2微观结构及电化学性能的影响

以镍钴氢氧化物、异丙醇铝为原料,采用水解法合成三元前驱体Ni_(0.88)Co_(0.07)Al_(0.05)O_2,再与锂盐混合烧结得到正极材料(TEM)、X射线光电子能谱(XPS)、能量色散X射线谱(EDS)和恒电流充放电测试等对样品的晶体结构、微观形貌、元素价态以及电化学性能进行表征。研究表明,料液比1∶25、水洗3次、600℃回烧2 h合成的LiNi_(0.88)Co_(0.07)Al_(0.05)O_2具有较优的综合电化学性能,其在0.2C的放电比容量达207.6 mAh·g~(-1),首次充放电效率为84.8%,1C放电比容量为192.0 mAh·g~(-1),循环100周后,材料的放电比容量仍有148.0 mAh·g~(-1),容量保持率达到77.1%。     

LiNi0.8Co0.15Al0.05O2正极材料的FePO4包覆改性

使用液相包覆工艺对LiNi_(0.8)Co_(0.15)Al_(0.05)O_2(NCA)材料进行FePO_4包覆改性,利用FePO_4优异的结构稳定性与热稳定性,对NCA的长期可靠性与安全性能进行改良。重点研究FePO_4包覆对NCA材料的改性效果,以及不同包覆量造成的NCA材料电化学性能差异。表面包覆的FePO_4保护层,能够防止NCA材料与电解液直接接触发生副反应,抑制长期循环过程中过渡金属离子的溶出,保持结构的长期稳定性。当包覆量为1.0%(w/w)时,NCA材料表现出最优的综合性能,充放电循环800次后,容量保持率依然高达95%,25℃下存储100 d后,容量保持率也高于95%,达到了兼顾能量密度、使用寿命及安全性能的理想效果。     

合成温度对全梯度正极材料LiNi_(0.7)Co_(0.15)Mn_(0.15)O_2的结构和电化学性能影响（英文）

通过控制结晶法和浓度梯度进料的方式制备了Ni、Co和Mn三元素组分含量呈全梯度分布的类球形Ni_(0.7)Co_(0.15)Mn_(0.15)(OH)_2前驱体,与LiOH·H_2O均匀混合并焙烧后获得LiNi_(0.7)Co_(0.15)Mn_(0.15)O_2正极材料,系统研究了不同焙烧温度对材料Ni、Co和Mn三元素扩散情况、晶体结构及电化学性能的影响规律。通过能谱仪(EDXS)分析不同焙烧温度下材料颗粒中Ni、Co、Mn三元素的扩散程度。研究结果表明,在800℃下焙烧得到的正极材料梯度分布特征明显且电化学性能最佳,首次放电比容量为186.1 m Ah·g~(-1)(2.8~4.3 V,0.2C),2C大倍率充放电条件下循环200次后容量保持率为90.1%。这种材料兼具高比容量及良好的循环稳定性,可以用作下一代高能量密度锂离子电池正极材料。     

高压实富镍正极材料LiNi_(0.85)Co_(0.06)Mn_(0.06)Al_(0.03)O_2的制备

通过控制结晶法制备高密度类球形Ni_(0.85)Co_(0.06)Mn_(0.06)Al_(0.03)(OH)_2前驱体,与LiOH·H_2O均匀混合后,在820℃于氧气气氛下进行高温煅烧,最终合成高压实富镍正极材料Li Ni_(0.85)Co_(0.06)Mn_(0.06)Al_(0.03)O_2。通过扫描电子显微镜(SEM)表征前驱体、正极材料及正极片的形貌;X射线衍射(XRD)表明材料具有良好的六方单相层状α-NaFeO_2结构,能谱仪(EDS)分析表明材料颗粒中各组分含量呈均匀分布。制备的LiNi_(0.85)Co_(0.06)Mn_(0.06)Al_(0.03)O_2正极材料具有良好的加工性能和很高的压实密度,极片压实密度达到了3.82 g·cm~(-3)。以该极片组装的模拟电池具有良好的电化学性能,尤其具有优异的倍率性能,在电压区间2.8~4.3 V和0.2C电流密度充放电条件下,首次放电比容量为211.7 mAh·g~(-1),首次充放电效率88.9%,5C大倍率充放电条件下容量仍达到180.2 mAh·g~(-1),循环200周容量保持率为80.4%。     

高比容量锂离子电池正极材料LiNi_(0.6)Co_(0.2)Mn_(0.2)O_(2)的制备及性能北大核心CSCD

以LiNi_(0.6)Co_(0.2)Mn_(0.2)O_(2)为研究对象,通过共沉淀法制备了不同F物质的量分数(0%、1%、3%、5%)的LiNi_(0.6)Co_(0.2)Mn_(0.2)O_(2)三元正极材料(NCM),通过对NCM材料的晶格结构、微观形貌、电化学性能进行分析,结果表明:F掺杂后提高了NCM材料的结晶度,降低了阳离子混乱程度,适量的F掺杂有助于减小NCM三元正极材料的尺寸和提高均匀性,F的掺杂还能够降低NCM三元正极材料的极化现象,初始放电比容量随着F的掺杂含量升高呈现出先升高后降低的趋势,循环性能随着F的掺杂得到了提高,F掺杂物质的量分数为3%的NCM三元正极材料初始放电比容量167.2 mA·h/g,容量保持率达到98.5%,阻抗较小,电化学性能最优。     

掺F影响LiNi0.8Co0.1Mn0.1O2结构和性能的微观机制

以氟化锂为氟源,通过高温固相法合成了F掺杂的LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2。采用X射线衍射仪(XRD)、扫描电镜(SEM)、X射线光电子能谱(XPS)和电化学测试等手段研究F影响LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2结构和性能的微观机制。结果表明:适量F掺杂可以提高正极材料的放电比容量,改善其倍率性、循环性和热稳定性。当F掺杂量(物质的量分数)为1.5%时,材料的综合电化学性能最优,初始放电比容量(0.2C)和50周循环容量保持率(1C)分别由原始的174.0 mAh·g~(-1)(78.7%)提高到178.6 mAh·g~(-1)(85.7%)。LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2材料性能的改善可归因于F能够增强过渡金属层、锂层与氧层之间的结合力,提高材料的结构稳定性。此外,F掺杂还有利于降低电化学反应中的界面电阻和电荷转移阻抗。     

丙酸乙酯对LiFePO4锂离子电池低温性能的影响

以丙酸乙酯(EP)作为碳酸乙烯酯(EC)、碳酸甲乙酯(EMC)和碳酸二甲酯(DMC)的共溶剂,研究其对LiFePO4锂离子电池低温电化学性能的影响.利用循环伏安曲线、交流阻抗图谱和恒电流充放电曲线等方法测试电池电化学性能.结果表明,添加一定量EP,可提高碳酸酯电解液的离子电导率,改善电解液与正极LiFePO4材料和负极石墨材料的相容性,从而提高LiFePO4锂离子电池的低温性能.使用1 mol·L-1LiPF6/(EC:EMC:DMC:EP=1:1:1:3,by mass)电解液的石墨/LiFePO4锂离子电池在10oC(1C)、-10oC(0.2C)、-20oC(0.2C)、-30oC(0.2C)和-40oC(0.2C)下的相对放电容量(以25oC时的放电容量为基准)分别为82.9%、75.6%、59.0%、46.4%和37.6%.     

Crystal and molecular structures of the Rh[(C2H5O)2PS2]3 and Co[(C6H5O)2PS2]3 chelate compounds

The crystal structures of the Rh[(EtO)₂PS₂]₃ (I) and Co[(PhO)₂PS₂]₃ (II) chelate compounds were determined from X-ray diffraction (XRD) data (CAD-4 diffractometer, MoK _β radiation, 1193 F _hkl , R = 0.0516 for I and 513 F _hkl , R = 0.0305 for II). Crystals I are monoclinic: a = 14.233(3) Å, b = 13.570(3) Å, c = 14.272(3) Å; β = 90.66(3)°, V = 2756.3(10) ų, Z = 4, ρ_calc = 1.587 g/cm³, space group C2/c. Crystals II are trigonal: a = 15.149(2) Å, c = 30.306(6) Å; V = 6023.2(16) ų, Z = 6, ρ_calc = 1.493 g/cm³, space group R3ˉ. Structures I and II consist of discrete mononuclear molecules. The coordination polyhedra of the M atoms (M = Rh, Co) are distorted octahedra formed by six sulfur atoms of three cyclic bidentate (RO)₂ PS₂⁻ ligands. Original Russian Text Copyright ? 2008 by R. F. Klevtsova, L. A. Glinskaya, and S. V. Larionov __________ Translated from Zhurnal Strukturnoi Khimii, Vol. 49, No. 2, pp. 330–334, March–April, 2008.     

Pt(PPh3)2-η2C60络合物的分子轨道研究

近年来,自Kratschmer 等人采用并不复杂的方法就能制备出宏观量的C_(60),人们对它的兴趣也从结构的研究逐渐转向化学性质的研究.C_(60)是目前自然界已知对称性最高的球状分子,每个C 原子都以接近sp~2杂化轨道和相邻的三个C 原子相联.C_(60)的NMR 化学位移以及闭壳层的电子结构和较宽的HOMO-LUMO 间隙,都说明它具有典型的芳香化合物——苯的某些特性.另外,掺杂(碱金属元素)后,它具有的导电性又表现出石墨具有的某些特点.     

高性能Ce0.35Zr0.55Y0.1O1.95稀土储氧材料的研究

The oxygen storage material (OSM) Ce_0.35Zr_0.55Y_0.1O_1.95 was prepared by co-precipitation routine and studied by means of TEM, XRD, XPS, BET, H₂-TPR and oxygen storage capacity (OSC) measurements. The results indicated that this material possessed plenty of Ce³⁺ and lattice oxygen vacancy (percentage of Ce³⁺ was 59.6%) and high cerium atom utilization ratio (80.04%). The porous material was with an average BET surface area of 97 m²·g^-1 and pore volume of 0.26 mL·g^-1. After aged at 1 000 ℃ in air for 5 h, the sample still possessed plenty of Ce³⁺ and lattice oxygen vacancy (percentage of Ce³⁺ was 57.1%), and showed high cerium atom utilization ratio (78.25%), and high thermal stability.     

Diagram of phase equilibria in the Fe2V4O13-WO3 system

A diagram for the phase equilibria established in the two-component Fe₂V₄O₁₃-WO₃ system (one of the intersections of the Fe₂O₃-V₂O₅-WO₃ three-component system) has been constructed based on the measurements made by DTA and X-ray phase analysis. The diagram shows that the system investigated does not appear to be a true two-component system, even below the solidus line.     

Jahn-Teller-distorted dimeric anions in (cat)[Mn2F8(H2O)2]·2H2O (cat = pipzH2, dabcoH2) and (dabcoH2)2[Mn2F8(H2PO4)2]

Using biprotonated dabco (1,4-diazabicyclo[2.2.2]octane) or pipz (piperazine) as counter cations, mixed-ligand fluoromanganates(III) with dimeric anions could be prepared from hydrofluoric acid solutions. The crystal structures were determined by X-ray diffraction on single crystals: dabcoH₂[Mn₂F₈(H₂O)₂]·2H₂O (1), space group P2₁, Z = 2, a = 6.944(1), b = 14.689(3), c = 7.307(1) Å, β = 93.75(3)°, R₁ = 0.0240; pipzH₂[Mn₂F₈(H₂O)₂]·2H₂O (2), space group , Z = 2, a = 6.977(1), b = 8.760(2), c = 12.584(3) Å, α = 83.79(3), β = 74.25(3), γ = 71.20(3)°, R₁ = 0.0451; (dabcoH₂)₂[Mn₂F₈(H₂PO₄)₂] (3), space group P2₁/n, Z = 4, a = 9.3447(4), b = 12.5208(4), c = 9.7591(6) Å, β = 94.392(8)°, R₁ = 0.0280. All three compounds show dimeric anions formed by [MnF₅O] octahedra (O from oxo ligands) sharing a common edge, with strongly asymmetric double fluorine bridges. In contrast to analogous dimeric anions of Al or Fe(III), the oxo ligands (H₂O (1,2) or phosphate (3)) are in equatorial trans-positions within the bridging plane. The strong pseudo-Jahn-Teller effect of octahedral Mn(III) complexes is documented in a huge elongation of an octahedral axis, namely that including the long bridging Mn-F bond and the Mn-O bond. In spite of different charge of the anion in the fluoride phosphate, the octahedral geometry is almost the same as in the aqua-fluoro compounds. The strong distortion is reflected also in the ligand field spectra.     

Electronic structure and reactivity of PO 43? , P2O 74? phosphate and SO 42? , S2O 72? sulfate anions

Group-theoretical analysis and molecular orbital methods were used to obtain (in analytical form) the electronic structure and reactivity of the PO ₄ ³⁻ , SO ₄ ²⁻ and P₂O ₇ ⁴⁻ , S₂O ₇ ²⁻ anions. The reactivity of the anions is dictated by the availability of lone electron pairs on the top quasidegenerate MOs in the form of linear combinations of group orbitals from atomic orbitals (AOs) of peripheral oxygen atoms for PO ₄ ³⁻ , SO ₄ ²⁻ and the central (bridging) atom for P₂O ₇ ⁴⁻ , S₂O ₇ ²⁻ . These electron pairs are responsible for the donor-acceptor interactions during complexation, clustering, and other (addition, substitution, etc.) reactions. Original Russian Text Copyright ? 2005 V. A. Zasukha, A. P. Shpak, V. V. Trachevskii, and E. V. Urubkova __________ Translated from Zhurnal Strukturnoi Khimii, Vol. 46, No. 3, pp. 405–415, May–June, 2005.     

Synthesis and characterization of NixMg1−xAl2O4 nano ceramic pigments via a combustion route

MgAl₂O₄ was successfully used as a crystalline host network for the synthesis of nickel-based nano cyan refractory ceramic pigments. Different compositions of Ni_xMg_1−xAl₂O₄ (0.1 ? x ? 0.8) powders have been prepared by using a low temperature combustion reaction (LTCR) of the corresponding metal nitrates with urea (U) as a fuel at 300 °C in an open air furnace. The as-synthesized samples were characterized by thermal analysis (TG-DTG/DTA), X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). UV-Vis and diffuse reflectance spectroscopy (DRS) using CIE- L^∗a^∗b^∗ parameters methods have been used for color measurements. The results show that the Ni_xMg_1−xAl₂O₄ samples are the crystalline phase with a particle size of 8.85-43.66 nm in the temperature range 500-1200 °C. The density, particle size, shape and color are determined for all the prepared samples with different calcination times and temperatures.     

The support and characterization of C60 and MoO3 on Al2O3

A new type of catalyst from supporting C₆₀ on MoO₃ and Al₂O₃ has been prepared. The effect of different order of impregnation and calcination atmosphere on catalyst are investigated by the solution test in toluene, UV-VIS spectroscopy and temperature programmed reduction (TPR). The results show that when the catalyst was prepared by supporting MoO₃ on C₆₀/Al₂O₃ and calcined in N₂, there is a stronger interaction between C₆₀, MoO₃ and Al₂O₃, but when supporting C₆₀ on MoO₃/Al₂O₃, the interaction is relatively weak. We consider that in the former method a new complex, Mo–C₆₀–O–Al, is formed.     

一个新颖的三维异核锑(III)-镨(III)配合物[Sb2-μ4-(EDTA)2Pr(H2O)5]NO3•4H2O的合成、晶体结构及热分解研究

合成了锑-镨与乙二胺四乙酸形成的新颖三维配合物[Sb₂-μ₄-(EDTA)₂Pr(H₂O)₅]NO₃•4H₂O, 用元素分析、红外光谱、热分析及X射线单晶衍射法等进行了组成和结构表征. 结果表明该配合物属正交晶系, 空间群Pnn2; 晶胞参数: a＝1.07031(2) nm, b＝2.30805(4) nm, c＝0.72343(2) nm, V＝1.78711(7) nm³, Z＝2, D_c＝2.202 g/cm³, F(000)＝1164, μ＝2.955 mm^－1, GOF＝1.000, 最终偏离因子R₁＝0.0203, wR₂＝0.0545 [I＞2σ(I)]. 在标题化合物中, 每个镨(III)离子的配位数为9, 与五个水分子中的五个氧原子和四个羧基氧原子配位, 形成三帽三角棱柱空间配位多面体. 锑(III)与EDTA离子中的四个氧原子和两个氮原子配位, 在赤道平面上有一孤对电子. 同时讨论了配合物的热分解过程.     

中温固体氧化物燃料电池复合阴极La1.6Sr0.4NiO4-Ce0.9Gd0.1O1.9的制备及性能研究

Composite cathodes consisting of -La_1.6Sr_0.4NiO₄(LSN) and -Ce_0.9Gd_0.1O_1.9(CGO) has been prepared for intermediate temperature solid oxide fuel cell (IT-SOFC). The chemical stability, microstructures and electrochemical performance of the cathode have been investigated using XRD, SEM and AC impedance spectroscopy. Results showed that strong bonding was formed between the composite electrodes and CGO electrolytes after the electrodes were fired at 1 050 ℃ for 4 hours. The polarization resistance changed with oxygen partial pressure, suggesting that charge transfer process was the rate limiting step for electrochemical oxygen reduction at the composite cathodes. Area specific resistance (ASR) for a LSN-40CGO composite cathode was 0.76 Ω·cm² at 700 ℃, which was four times lower than that of a pure LSN cathode. 1.7％ decrease of the cathode current density was observed in the stability test of the composite cathode.