Preparation of “pore-fill” type Pd–YSZ–γ-Al2O3 composite membrane supported on α-Al2O3 tube for hydrogen separation

Mesoporous YSZ–γ-Al₂O₃ membranes were coated on α-Al₂O₃ (Ø2 mm) tube by dipping the α-Al₂O₃ support tube into mixed sol consists of nano-size YSZ and bohemite particles followed by drying and calcination at 600 °C. Addition of bohemite in YSZ sol helped a good adhesion and uniform coating of the membrane film onto α-Al₂O₃ support. The quality of the mesoporous YSZ–γ-Al₂O₃ membranes was evaluated by the gas permeability experiments. The number of defects was minimized when the γ-Al₂O₃ content became more than 40%. Addition of γ-Al₂O₃ inhibited the crystal growth of YSZ, sintering shrinkage and distortion stress. Increase of calcination temperature and time results in the increase of pore size and N₂ permeance. A hydrogen perm-selective membrane was prepared by filling palladium into the nano-pores of YSZ–γ-Al₂O₃ layer by vacuum-assisted electroless plating. Crystal growth of palladium was observed by thermal annealing of the membrane at 600 °C for 40 h. The Pd–YSZ–γ-Al₂O₃ composite membrane revealed improved thermal stability allowing long-term operation at elevated temperature (>500 °C). This has been attributed to the improved fracture toughness of YSZ–γ-Al₂O₃ layer and matching of thermal expansion coefficient between palladium and YSZ. Although fracture of the membrane did not occur, decline of H₂ flux was observed when the membrane was exposed in 600 °C. This has been attributed to the agglomeration of palladium particles by crystal growth and dense packing into the pore networks of YSZ–γ-Al₂O₃ by elevation of temperature.     

Macroscopic and spectroscopic characterization of selenate, selenite, and chromate adsorption at the solid–water interface of γ-Al2O3

The interaction of selenate, selenite, and chromate with the hydrated surface of γ-Al₂O₃ was studied using a combination of macroscopic pH edge data, electrophoretic mobility measurements, and X-ray absorption spectroscopic analyses. The pH edge data show generally increased oxyanion adsorption with decreasing pH, and indicate ionic strength-(in)dependent adsorption of chromate and selenate across the pH range 4–9, and ionic strength-(in)dependent adsorption of selenite in this pH range. The adsorption of chromate peaks at pH 5.0, whereas for selenate and selenite no pH adsorption maxima are observed. Electrophoretic mobility measurements show that all three oxyanions decrease the zeta potential of γ-Al₂O₃ upon adsorption; however, only selenite decreased the pH_PZC of the γ-Al₂O₃ sorbent. EXAFS data indicate that selenite ions are coordinated in a bridging bidentate fashion to surface AlO₆ octahedra, whereas no second-neighbor Al scattering was observed for adsorbed selenate ions. Combined, the results presented here show that pH is a major factor in determining the extent of adsorption of selenate, selenite, and chromate on hydrated γ-Al₂O₃. The results point to substantial differences between these anions as to the mode of adsorption at the hydrated γ-Al₂O₃ surface, with selenate adsorbing as nonprotonated outer-sphere complexes, chromate forming a mixture of monoprotonated and nonprotonated outer-sphere adsorption complexes, and selenite coordinating as inner-sphere surface complexes in bridging configuration.     

Ternary [Al2O3–electrolyte–Cu] species: EPR spectroscopy and surface complexation modeling

Cu²⁺ binding on γ-Al₂O₃ is modulated by common electrolyte ions such as Mg²⁺, , and in a complex manner: (a) At high concentrations of electrolyte ions, Cu²⁺ uptake by γ-Al₂O₃ is inhibited. This is partially due to bulk ionic strength effects and, mostly, due to direct competition between Mg²⁺ and Cu²⁺ ions for the SO⁻ surface sites of γ-Al₂O₃. (b) At low concentrations of electrolyte ions, Cu²⁺ uptake by γ-Al₂O₃ can be enhanced. This is due to synergistic coadsorption of Cu²⁺ and electrolyte anions, and _. This results in the formation of ternary surface species (SOH₂SO₄Cu)⁺, (SOH₂PO₄Cu), and (SOH₂HPO₄Cu)⁺ which enhance Cu²⁺ uptake at pH < 6. The effect of phosphate ions may be particularly strong resulting in a 100% Cu uptake by the oxide surface. (c) EPR spectroscopy shows that at pH  pH_PZC, Cu²⁺ coordinates to one SO⁻ group. Phosphate anions form stronger, binary or ternary, surface species than sulfate anions. At pH  pH_PZC Cu²⁺ may coordinate to two SO⁻ groups. At pH  pH_PZC electrolyte ions and are bridging one O-atom from the γ-Al₂O₃ surface and one Cu²⁺ ion forming ternary [γ-Al₂O₃/elecrolyte/Cu²⁺] species.     

Chromium doped γ-Al2O3 powders. Features of the electrical double layer and state of the surface species

γ-Al₂O₃ samples, both pure and Cr doped, were prepared by heating at 470°C sol–gel precursors obtained by using aluminum tri-sec-butoxide [Al(OC₄H₉)₃] as the starting compound. The samples were characterised for phase composition (X-ray diffraction) and surface area (BET). Electrochemical determinations of the double layer reactivity of the pure and doped oxides were performed both by surface charge and by electrokinetic sonic amplitude (ESA) determinations. The interfacial electrostatic response is discussed and analysed also with reference to the sample surface state obtained by X-ray photoelectron spectroscopy (XPS).     

Energetics of copper diphosphates – Cu2P2O7 and Cu3(P2O6OH)2

Differential scanning calorimetry and high temperature oxide melt solution calorimetry are used to study enthalpy of phase transition and enthalpies of formation of Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂. α-Cu₂P₂O₇ is reversibly transformed to β-Cu₂P₂O₇ at 338–363 K with an enthalpy of phase transition of 0.15 ± 0.03 kJ mol⁻¹. Enthalpies of formation from oxides of α-Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂ are −279.0 ± 1.4 kJ mol⁻¹ and −538.8 ± 2.7 kJ mol⁻¹, and their standard enthalpies of formation (enthalpy of formation from elements) are −2096.1 ± 4.3 kJ mol⁻¹ and −4302.7 ± 6.7 kJ mol⁻¹, respectively. The presence of hydrogen in diphosphate groups changes the geometry of Cu(II) and decreases acid–base interaction between oxide components in Cu₃(P₂O₆OH)₂, thus decreasing its thermodynamic stability.     

The Phase Relations in the System In2O3–TiO2–MgO at 1100 and 1350°C

The phase relations in the system In₂O₃–TiO₂–MgO at 1100 and 1350°C are determined by a classical quenching method. In this system, there are four pseudobinary compounds, In₂TiO₅, MgTi₂O₅ (pseudobrookite type), MgTiO₃ (ilmenite type), and Mg₂TiO₄ (spinel type) at 1100°C. At 1350°C, in addition to these compounds there exist a spinel-type solid solution Mg_2−xIn_2xTi_1−xO₄ (0≤x≤1) and a compound In₆Ti₆MgO₂₂ with lattice constants a=5.9236(7) Å, b=3.3862(4) Å, c=6.3609(7) Å, β=108.15(1)°, and q=0.369, which is isostructural with the monoclinic In₃Ti₂FeO₁₀ in the system In₂O₃–TiO₂–MgO. The relation between the lattice constants of the spinel phase and the composition nearly satisfies Vegard's law. In₆Ti₆MgO₂₂ extends a solid solution range to In₂₀Ti₁₇Mg₃O₆₇ with lattice constants of a=5.9230(5) Å, b=3.3823(3) Å, c=6.3698(6) Å, β=108.10(5)°, and q=0.360. The distributions of constituent cations in the solid solutions are discussed in terms of their ionic radius and site preference effect.     

Synthesis and ac susceptibility of YCa2Cu3O7−δ

The bulk superconducting YCa₂Cu₃O_7−δ compounds are prepared at an ordinary pressure of oxygen by conventional solid-state reaction method. The formation of sample is tested by means of XRD and is studied for their ac susceptibility below room temperature up to 77.5 K. The samples are found single-phase orthorhombic structure and found superconducting at 83.5 K. It is shown that the analysis is consistent with published data on YBa₂Cu₃O_7−δ oxide superconductor.     

Environment-friendly synthesis of N-phenylpiperidine from aniline and 1,5-pentanediol over γ-Al2O3 catalyst

An efficient environment-friendly synthesis of N-phenylpiperidine was developed from aniline and 1,5-pentanediol over γ-Al2O3 catalyst under atmospheric pressure. The conversion of 1,5-pentanediol reached 97% and the selectivity for N-phenylpiperidine attained 94%. The structure of the catalyst was characterized by NH3-TPD and BET. The influences of calcination temperature of the catalyst and reaction temperature on activity and selectivity of the catalyst were investigated.     

ZrO4/SiO2-Al2O3催化肉桂醛MPV转移加氢性能

以九水合硝酸铝（Al（NO₃）₃·9H₂O）与正硅酸乙酯（TEOS）为前驱盐,采用溶胶-凝胶法制备一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,并通过浸渍硝酸氧锆引入ZrO₂,制备ZrO₂/SiO₂-Al₂O₃复合氧化物催化剂,考察催化剂在肉桂醛（CAL）MPV转移加氢中的催化性能,并结合N₂物理吸附、X射线粉末衍射（XRD）、傅里叶变换红外光谱（FTIR）、NH₃-程度升温脱附（NH₃-TPD）、Py-原位红外（Py-IR）等技术,研究催化剂结构、织构以及表面性质与其催化性能间的构效关系.研究表明,所制备的催化剂均以L酸为主,并含有少量B酸中心,这使得加氢产物以肉桂醇（COL）为主,并含有少量1-苯丙烯-2-丙基醚（CPE）.Al₂O₃含量不仅影响催化剂表面的酸中心数量,而且对催化剂的织构参数有较大影响.随Al₂O₃含量的增加,催化剂表面L酸与B酸中心均有所增加,而孔径则持续变小,这使得催化反应呈现CAL转化率先增加后减少、目标产物COL选择性先稍有减小后有所增加的趋势.在Si/Al比为2时,催化剂具有最优的催化性能,优化反应条件下,CAL转化率达96%,目标产物COL选择性达90%.     

不同磷含量对NiMoP/Al2O3加氢处理催化剂的影响

采用NiMoP浸渍液浸渍载体γ Al₂O₃制备了不同磷含量的NiMoP/Al₂O₃加氢处理催化剂。为了研究磷对该系列催化剂活性相结构的影响,用二苯并噻吩（DBT）和喹啉为模型化合物,考察了催化剂的加氢脱硫（HDS）和加氢脱氮（HDN）性能。结果表明,添加适当的磷能够提高催化剂的HDS和HDN活性,但是高含量的磷能显著的降低催化剂的催化性能。通过对催化剂进行XRD和HRTEM表征发现,添加磷能够增加MoS2的堆积层数以及Ⅱ型“Ni-Mo-S”相的相对含量,这是因为在制备过程中添加磷降低了活性组分与载体之间的相互作用。     

Formation of α-Fe2O3/FeOOH nanostructures with various morphologies by a hydrothermal route and their photocatalytic properties

A series of α-Fe₂O₃/FeOOH nanostructures with different morphologies have successfully been synthesized based on K₄[Fe(CN)₆] at 140 °C by a novel hydrothermal method. The morphology and phase of α-Fe₂O₃/FeOOH can be controlled by adjusting the reaction time. UV–vis absorption spectrum, X-ray powder diffraction, and transmission electron microscopy analyses were used to characterize the resulting products. A detailed, rational mechanism is proposed for the formation of α-Fe₂O₃/FeOOH nanostructures. The potential applications of the as-synthesized α-Fe₂O₃/FeOOH nanoparticles with different morphologies on photocatalytic decomposition of salicylic acid were also investigated.     

Electrochemically regenerative visible light-induced reactivity of α-Fe2O3 films with Ag(core)–AgCl(shell) microcrystal composites

Ag(core)–AgCl(shell) microcrystal composites (Ag@AgCl) have been formed on an α-Fe₂O₃ film-coated SnO₂ electrode by a 2 step method consisting of the electrochemical reduction of Ag⁺ ions and the subsequent electrochemical oxidation. The synergy of α-Fe₂O₃ and Ag@AgCl gave rise to a high visible light-induced reactivity (λ_ex > 420 nm) for the oxidation of 2-naphthol (2-NAP) used as a model water pollutant in the presence and absence of oxygen. These findings were attributable to the function of Ag@AgCl composites as an excellent charge-separation promoter and built-in acceptor.     

Self-powdering and nonlinear optical domain structures in ferroelastic β′-Gd2(MoO4)3 crystals formed in glass

Ferroelastic β′-Gd₂(MoO₄)₃, (GMO), crystals are formed through the crystallization of 21.25Gd₂O₃–63.75MoO₃–15B₂O₃ glass (mol%), and two scientific curious phenomena are observed. (1) GMO crystals formed in the crystallization break into small pieces with a triangular prism or pyramid shape having a length of 50–500 μm spontaneously during the crystallizations in the inside of an electric furnace, not during the cooling in air after the crystallization. This phenomenon is called “self-powdering phenomenon during crystallization” in this paper. (2) Each self-powdered GMO crystal grain shows a periodic domain structure with different refractive indices, and a spatially periodic second harmonic generation (SHG) depending on the domain structure is observed. It is proposed from polarized micro-Raman scattering spectra and the azimuthal dependence of second harmonic intensities that GMO crystals are oriented in each crystal grain and the orientation of (MoO₄)²⁻ tetrahedra in GMO crystals changes periodically due to spontaneous strains in ferroelastic GMO crystals.     

Photodegradation of 2,4-D over PdO/Al2O3-Nd2O3 photocatalysts prepared by the sol-gel method

The photocatalytic activity of 1.0 wt% PdO supported on Al₂O₃-Nd₂O₃ binary oxides prepared by the sol-gel method was studied in the photodegradation of 2,4-dichlorophenoxyacetic acid (2,4-D). The photocatalysts were characterized by N₂ physisorption, XRD and UV-vis spectroscopy. PdO supported on γ-Al₂O₃ photo-degrades the 2,4-D, however the addition of Nd₂O₃ to γ-Al₂O₃ notably improves the photocatalytic activity. As the concentration of Nd₂O₃ in the binary oxide increases from 2 to 10 wt%, the photodegradation of 2,4-D is highly enhanced. The catalytic test for PdO supported on pure Nd₂O₃ showed scarce photocatalytic activity. Total organic carbon (TOC) analysis showed that the 2,4-D has been completely destroyed on the PdO/Al₂O₃-Nd₂O₃ photocatalysts after 6 h under irradiation.     

High-pressure preparation, crystal structure, and properties of the new rare-earth oxoborate β-Dy2B4O9

In this work we report about a new rare-earth oxoborate β-Dy₂B₄O₉ synthesized under high-pressure/high-temperature conditions from Dy₂O₃ and boron oxide B₂O₃ in a B₂O₃/Na₂O₂ flux with a walker-type multianvil apparatus at 8 GPa and 1000°C. Single crystal X-ray structure determination of β-Dy₂B₄O₉ revealed: , a=616.2(1) pm, b=642.8(1) pm, c=748.5(1) pm, α=102.54(1)°, β=97.08(1)°, γ=102.45(1)°, Z=2, R1=0.0151, wR₂=0.0475 (all data). The compound exhibits a new structure type which is built up from bands of linked BO₃- (Δ) and tetrahedral BO₄-groups (□). The Dy³⁺-cations are positioned in the voids between the bands. According to the conception of fundamental building blocks β-Dy₂B₄O₉ can be classified with the notation 2Δ6□:Δ3□=4□=3□Δ. Furthermore we report about temperature-resolved in situ powder diffraction measurements and IR-spectroscopic investigations on β-Dy₂B₄O₉.     

Chemoselective synthesis of δ-lactones via benzyl radical cyclization utilizing K2S2O8–CuCl2

Direct chemoselective oxidation of δ-lactones via highly stable benzyl radical cyclization is reported. The one-pot conversion of premade substituted 5-aryl pentanoic acid and 8-benzyl-1-naphthoic acid in the presence of K2S2Os--CuCl2 results to the δ-lactones in moderate to good yields. The advantages of this methodology is using water as a solvent and utilizing available starting materials.     

High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte based PCMFCs with stable Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 μm in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm⁻², and a low polarization resistance of the electrodes of 0.08 Ω cm² was achieved at 700 °C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells.     

Synthesis and characterization of Fe2O3/SiO2 nanocomposites

Fe₂O₃/SiO₂ nanocomposites based on fumed silica A-300 (S_BET = 337 m²/g) with iron oxide deposits at different content were synthesized using Fe(III) acetylacetonate (Fe(acac)₃) dissolved in isopropyl alcohol or carbon tetrachloride for impregnation of the nanosilica powder at different amounts of Fe(acac)₃ then oxidized in air at 400–900 °C. Samples with Fe(acac)₃ adsorbed onto nanosilica and samples with Fe₂O₃/SiO₂ including 6–17 wt% of Fe₂O₃ were investigated using XRD, XPS, TG/DTA, TPD MS, FTIR, AFM, nitrogen adsorption, Mössbauer spectroscopy, and quantum chemistry methods. The structural characteristics and phase composition of Fe₂O₃ deposits depend on reaction conditions, solvent type, content of grafted iron oxide, and post-reaction treatments. The iron oxide deposits on A-300 (impregnated by the Fe(acac)₃ solution in isopropanol) treated at 500–600 °C include several phases characterized by different nanoparticle size distributions; however, in the case of impregnation of A-300 by the Fe(acac)₃ solution in carbon tetrachloride only α-Fe₂O₃ phase is formed in addition to amorphous Fe₂O₃. The Fe₂O₃/SiO₂ materials remain loose (similar to the A-300 matrix) at the bulk density of 0.12–0.15 g/cm³ and S_BET = 265–310 m²/g.     

Mo_2C/γ-Al_2O_3催化剂上苯加氢反应的原位红外光谱研究

采用程序升温反应法制备了钝化态、还原钝化态和新鲜态Mo2C/γ-Al2O3催化剂,结合原位红外光谱表征技术和反应性能评价,考察、比较了三种催化剂苯加氢反应活性.原位红外光谱结果表明,新鲜态Mo2C/γ-Al2O3催化剂在室温就显示了较好的苯加氢反应活性,表现了类贵金属的催化活性.CO吸附在反应前后新鲜态Mo2C/γ-Al2O3催化剂上的对比结果表明,低价态的Mo位(Moδ+(0δ2))是苯加氢反应活性中心.三种催化剂的反应活性结果表明,新鲜态Mo2C/γ-Al2O3催化剂反应活性最好,催化剂寿命最长,失活之后在500°C下H2处理即可恢复原有活性.