催化动力学光度法测定痕量钒(Ⅴ)的研究

在乙酸介质中,痕量钒(Ⅴ)对过硫酸钾氧化1 (2 吡啶偶氮)\|2 萘酚(PAN)褪色的指示反应有灵敏的催化作用。研究了该催化反应的最佳实验条件和动力学参数,建立了一种测定痕量钒(Ⅴ)的新方法,其线性范围为0.0～40.0μg/L钒(Ⅴ),方法检出限为2.62×10-9g/mL。     

KBrO3-5-Br-PADAP体系催化动力学光度法测定痕量亚硫酸根

在H3PO4介质和室温条件下,痕量SO32-能灵敏地催化KBrO3氧化5-溴-(2-吡啶偶氮)-二乙氨基酚(5-Br-PADAP)的褪色反应。研究了该催化反应的最佳实验条件,建立了催化动力学光度法测定痕量SO32-的新方法。方法的线性范围为0.3~2.7μg/mL,检出限为1.82×10-7g/mL。该法用于白葡萄酒中SO32-含量的测定,结果令人满意。     

β-环糊精交联聚合物树脂相分光光度法测定水中痕量汞

以β-环糊精和环氧氯丙烷为原料合成了环糊精聚合树脂,将其作为显色剂2-[5-溴-(2-吡啶偶氮)]-5-二乙氨基苯酚的载体,采用β-环糊精-2-[5-溴-(2-吡啶偶氮)]-5-二乙氨基苯酚树脂相分光光度法测定微量汞.配合物的最大吸收波长为585nm,表观摩尔吸光系数为8.17×105L/mol·cm,汞含量在0～10μg/25mL范围内服从比尔定律,线性回归方程:y=0.0013 0.0163x,相关系数r=0.9994,加标回收率为98.5%～101.0%,与双硫腙法相比无显著性差异.该方法已用于工业废水中痕量汞的测定,结果令人满意.     

新试剂2-(5-硝基-2-吡啶偶氮)-5-二甲氨基苯甲酸分光光度法测定微量钴

本文报道用新试剂2-(5-硝基-2-吡啶偶氮)-5-二甲氨基苯甲酸分光光度法测定微量钴。配合物的表观摩尔吸光系数为1.31×10~5L·mol~(-1)·cm~(-1),Co∶5-NO_2-PAMB=1∶2,Co浓度在0～14μg/25mL范围内服从比耳定律。用于金属有机化合物中微量钴的测定,结果与理论值相符。     

矿石中微量钒分析方法的研究

胶束增溶光度法测定微量钒已有报导,用2-(5-溴-吡啶偶氮)-5-二乙氨基苯酚(5-Br-PADAP)-H_2O_2测定钒的方法也有报导。本文在此基础上研究了在表面活性剂8176存在下,用5-Br-PADAP光度法测定钒(V)的适宜条件及络合物的组成,提出了一个重现性好,灵敏度高,操作简便的测定矿石中微量钒的新方法。络合物(1:1)的最大吸收波长和表观摩尔吸光系数分别为590nm和9.06×10~4l·mol~(-1)·cm~(-1),最低检测限为0.008μg/ml,在0.2～16μgV(V)/25ml范围内遵守比尔定律,并满意地应用于硅酸盐和铁矿石中钒的测定。 1.主要试剂与仪器:     

2-(5-羧基-1,3,4-三氮唑偶氮)-5-二乙氨基苯甲酸-过氧化氢催化动力学光度法测定痕量铁的研究

研究了铁(Ⅲ)催化H2O2氧化2-(5-羧基-1,3,4-三氮唑偶氮)-5-二乙氨基苯甲酸(CTZDBA)的褪色反应及其动力学条件,褪色反应程度与铁(Ⅲ)量在一定范围内呈线性关系,建立了测定痕量铁(Ⅲ)的催化动力学光度法。在pH4.0的HAc-NaAc缓冲溶液介质中,褪色体系的最大吸收波长581nm,Fe(Ⅲ)的质量浓度在0.0008～0.04μg/mL范围内符合线性关系,回归方程为ΔA=25.325ρ-8.02×10-3(ρ:μg/mL),相关系数为0.9977,检出限3.78×10-10g/mL,方法用于头发和面粉中痕量铁的测定,结果与AAS测定结果相符。     

核固红-溴酸钾催化动力学光度法测定痕量钒

在pH2.5～2.9的硫酸溶液中,微量钒(Ⅴ)能显著催化溴酸钾氧化核固红(1氨基2,4二羟基蒽醌3磺酸钠)(C.I.No.60760)褪色。研究了反应的动力学行为,建立了测定痕量钒的催化动力学分析方法。该方法的检出限为1.9×10-6g·L-1,线性范围为0.03～1.5μg/25mL,用于测定中草药及食品中痕量钒,结果满意。     

流动注射催化光度法测定微量Sb(Ⅲ)

基于在B-R缓冲溶液介质中,Sb(Ⅲ)对H2O2氧化孔雀石绿褪色反应具有催化作用,建立了流动注射催化动力学光度法测定微量元素Sb(Ⅲ)的新分析方法,该方法的线性范围为0.010～2.0μg/mL,检出限为7.8×10-3μg/mL,r=0.9996。对0.1μg/mL Sb(Ⅲ)测定的RSD=0.97%n=11,进样频率为22.8次/h。用于环境水样中微量Sb(Ⅲ)的测定,回收率为97.3%～97.7%。     

1-(2-吡啶偶氮)-2-萘酚-过氧化氢光度法测定土壤中痕量钒

对钒(V)与1-(2-吡啶偶氮)-2-萘酚-过氧化氢-十六烷基三甲基溴化铵显色反应进行了试验,结果表明:在1 mol·L-1盐酸介质中,在十六烷基三甲基溴化铵存在下,钒(V)与1-(2-吡啶偶氮)-2-萘酚和过氧化氢反应生成红色多元络合物,络合物的最大吸收波长为577 nm,表观摩尔吸光率为3.04×104L·mol-1·cm-1,钒(V)的质量浓度在1.0 mg·L-1以内符合比耳定律.络合物的组成比为n钒(V):nPAN:n过氧化氢=1:1:1.方法用于土壤试样中痕量钒的测定,测定值的相对标准偏差(n=6)均小于9%,回收率在97.8%～101.5%之间,测得标准样品(GSS-5)中钒的含量为170.45μg·g-1,与标准值(166±9)μg·g-1之间的相对误差为2.7%.     

催化动力学光度法测定青霉素G及其机理研究

研究了在青霉素G存在下双氧水氧化苋菜红的褪色反应,建立了催化动力学光度法测定微量青霉素G的方法.方法线性范围为0.20～4.00μg/mL,回归方程y=-0.015p(μg/mL)+0.311,r=0.9998;方法线性范围为4.00～50.0μg/mL,回归方程y=0.001p(μg/mL)+0.280,r=0.99...     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.