超声辅助离子液体液相微萃取-高效液相色谱法分析水样中加替沙星或氟罗沙星

建立了一种采用离子液体1-己基-3-甲基咪唑六氟磷酸([C6mim][PF6])为萃取剂,超声辅助离子液体液相微萃取-高效液相色谱法分析水样中加替沙星和氟罗沙星的方法。 实验考察了溶液酸度、离子液体用量等因素对萃取的影响。在pH值分别为3.3、2.1的加替沙星和氟罗沙星水样中,加入0.4 mL [C6mim][PF6],超声,离心,离子液体相直接用于HPLC进行分析。 该方法的线性范围为0.5~50 mg/L,测定加替沙星和氟罗沙星的相对标准偏差(n=5)为2.80%和5.93%,二者的检出限分别为0.46、0.97 μg/L,该方法萃取水样中加替沙星的加标回收率为80.5%~89.5%,氟罗沙星的加标回收率可达93.3%~99.0%。     

超声辅助离子液体分散液相微萃取-高效液相色谱法测定废水中雌激素的研究

将离子液体、分散液相微萃取与超声萃取技术结合,采用疏水性离子液体1-丁基-3-甲基咪唑六氟磷酸盐([C4 MIM][PF6])为萃取剂,建立了超声辅助离子液体分散液相微萃取-高效液相色谱法分析废水中3种雌激素物质(己烯雌酚、双烯雌酚、己烷雌酚)方法.试验采用50μL的离子液体,考察了溶液体积、溶液pH值、超声时间、静置时间、离心时间等因素对富集效果的影响.最佳的萃取条件为:溶液体积为6 mL,甲醇体积0.3 mL,溶液pH值为2.0,超声时间6min,静置时间30min,离心时间10 min.在优化的萃取条件下,3种雌激素的富集倍数可达到96.8～112.4倍;方法的线性范围为0.5-100.0μg/L;检出限为0.25～0.50μ/L.对浓度为5.0μg/L的3种物质测定6次的相对标准偏差为9.2%～10.8%.     

基于离子液体的液相微萃取-高效液相色谱法测定水中有机磷农药

建立了基于1-丁基-3-甲基咪唑六氟磷酸盐离子液体的液相微萃取-高效液相色谱分析水样中甲拌磷、对硫磷和辛硫磷的方法。考察了萃取溶剂、萃取溶剂与样品溶液体积比、萃取时间、萃取温度和搅拌速度对液相微萃取的影响。在优化的萃取条件下,甲拌磷、对硫磷、辛硫磷3种农药的富集倍数分别为665、630和553倍;方法有好的线性范围(0.01-1μL/L)和低的检出限(0.001-0.01μL/L,S/N=3)。对0.1μL/L的甲拌磷,对硫磷和辛硫磷测定3次的相对标准偏差分别为3.44%、10.50%和2.41%。     

离子液体液-液萃取-高效液相色谱测定水中酚类化合物

建立了离子液体1-丁基-3-甲基咪唑六氟磷酸盐([C4mim][PF6])液-液萃取-高效液相色谱测定水中酚类化合物的方法.研究了水相pH值、萃取时间、水相体积及盐的浓度对萃取的影响.最佳萃取条件分别为:水相pH值为5,萃取时间为40 min,水相体积为60 mL.对比了离子液体对1-辛醇对苯酚、4-硝基苯酚、2-硝基苯酚、2,4-二甲基苯酚和双酚A的富集效率.在最佳条件下,离子液体对5种酚的富集倍率在9～151之间,方法对苯酚、4-硝基苯酚、2-硝基苯酚、2,4-二甲基苯酚和双酚A的检出限分别为:2.0、0.9、0.3、1.8和1.1 μg/L.将该方法应用于自来水、河水、湖水和污水的检测,回收率为87.9%～109.9%.     

离子液体双水相萃取-高效液相色谱-串联质谱法测定尿液中溴鼠灵

提出了离子液体双水相萃取-高效液相色谱-串联质谱法测定尿液中溴鼠灵。采用亲水性离子液体1-丁基-3-甲基咪唑四氟硼酸盐和磷酸二氢钠组成的双水相体系对样品进行萃取。萃取液在XDB C18色谱柱上分离,以甲醇-0.2%(φ)乙酸(85+15)混合溶液为流动相进行洗脱。采用电喷雾电离-多反应监测模式测定。溴鼠灵的线性范围为0.02~2.0μg·L-1,测定下限(10S/N)为0.015μg·L-1。空白尿样的加标回收率在86.8%~92.5%之间,测定值的日内、日间相对标准偏差(n=6)分别为3.3%~8.1%,6.2%~9.7%。方法可应用于尿液中溴鼠灵的测定。     

离子液体超声辅助萃取/LC-MS法测定环境水中痕量五氯酚

建立了离子液体超声辅助萃取/液相色谱-质谱联用测定环境水中痕量五氯酚(PCP)的方法。采用离子液体1-丁基-3-甲基咪唑六氟磷酸盐[C4mim][PF6]为萃取剂,考察了试样体积、p H值、温度、超声萃取时间和无机盐含量等因素对PCP萃取效率的影响,试样在XDB C18(150 mm×2.1 mm,5μm)色谱柱上,以甲醇-2 mmol/L醋酸铵溶液(70∶30)为流动相,电喷雾(ESI)电离负离子选择离子监测模式(SIM)进行测定。在优化的萃取条件下,PCP在0.005~1.0μg·L-1范围内具有良好线性,相关系数(r)为0.999 2,回收率为91.0%~97.0%,日内相对标准偏差(RSD)为1.1%~5.4%,日间RSD为3.8%~8.3%,定量下限为0.005μg·L-1。建立的方法简便、干扰少、特异性强,可用于环境水样中痕量PCP的测定。     

漩涡辅助离子液体-分散液液萃取环境水样中的紫外线吸收剂

建立了漩涡辅助离子液体-分散液液萃取(VA-IL-DLLME)的样品前处理技术,并与高效液相色谱联用检测环境水样中的紫外线吸收剂。以1-己基-3-甲基咪唑六氟磷酸为萃取剂,考察了离子液体用量、分散剂种类和用量、漩涡时间、离心时间、稀释剂种类和用量、p H等因素对萃取效率的影响。在最佳萃取条件下,2,4-二羟基二苯甲酮在4~1000 ng/m L、2-羟基-4-甲氧基二苯甲酮在3.5~1000 ng/m L、二苯甲酮,水杨酸-2-乙基己酯和3,3,5-三甲基环己烷水杨酸酯在10~1000 ng/m L浓度范围内具有良好的线性关系(R20.993),检出限为0.8~2.8 ng/m L,相对标准偏差(RSD)为2.6%~7.8%,加标回收率为55.8%~118.9%。方法可用于环境水样中痕量紫外线吸收剂的测定。     

吡啶离子液体双水相-高效液相色谱法同时测定牛奶中3种喹诺酮药物残留

建立了吡啶离子液体双水相-高效液相色谱同时测定牛奶中噁喹酸、萘啶酸及氟甲喹3种喹诺酮药物残留的方法. 牛奶样品经氯化钠和磷酸混合溶液提取后, 采用吡啶离子液体N-乙基-2-甲基吡啶溴化盐([EMPy]Br)和K2HPO4形成的双水相体系萃取富集, 以0.1%磷酸水溶液-乙腈为流动相, 梯度洗脱, 紫外检测. 该方法对噁喹酸、萘啶酸和氟甲喹测定的线性范围分别为0.3~15, 0.5~20和0.5~25 μg/mL, 相关系数(r)均大于0.9997, 3种药物的检出限在8~10 μg/kg之间. 对不同加标浓度的牛奶样品测定, 绝对回收率均在86.4%~94.8%范围内, 相对标准偏差为3.6%~8.3%. 该方法对牛奶中喹诺酮药物残留的检测具有简单、快速、环保和灵敏度高等优点.     

超高效液相色谱-串联质谱法同时测定食品中4种常用香精

建立了超高效液相色谱-串联质谱法同时测定食品中香兰素、乙基香兰素、麦芽酚和乙基麦芽酚4种香精的方法。样品用水提取,固相萃取小柱净化,目标化合物采用UPLC^TMBEH C18色谱柱(50 mm×2.1 mm, 1.7 μm)分离,以甲醇和含0.002 mol/L乙酸铵及0.1%(v/v)甲酸的水溶液为流动相进行梯度洗脱,采用电喷雾离子源电离、正离子多反应监测模式质谱检测。4种香精在5~500 μg/L或10~1000 μg/L质量浓度范围内线性良好,相关系数均在0.9995~0.9998之间;回收率为75.8%~116%,相对标准偏差(RSD, n=6)为1.58%~4.01%。该方法灵敏、准确,检测范围广,分析速度快,适合食品中香兰素、乙基香兰素、麦芽酚和乙基麦芽酚4种香精的检测。     

磁固相萃取-液相色谱法测定环境水样中有机紫外防晒剂

采用自制的聚离子液体功能化磁性材料有效富集有机紫外防晒剂，并与高效液相色谱-二极管阵列检测器（HPLC-DAD）联用，建立了环境水样中痕量有机紫外防晒剂的检测方法。研究系统考察了解吸溶剂、吸附和解吸时间、样品pH值、离子强度等因素对萃取性能的影响。在最佳萃取条件下，水杨酸辛酯的线性范围为0.5~200.0 μg/L，其他有机紫外防晒剂的线性范围为0.2~200.0 μg/L；6种目标物的检出限（LOD，S/N=3）和定量限（LOQ，S/N=10）分别为0.009~0.13 μg/L和0.031~0.43 μg/L。所建方法成功用于实际环境水样中有机紫外防晒剂的测定，不同加标水平下目标物的加标回收率为71.4%~120%，相对标准偏差均低于10%。研究表明，所建方法具有操作简便、萃取速度快、灵敏度高和环境友好等特点，可用于环境水样中有机紫外防晒剂的检测。     

红外伏吸法研究抗坏血酸在水溶液和离子液体1-乙基-3-甲基咪唑四氟硼酸盐中的电化学行为

采用电化学及红外伏吸法研究了抗坏血酸(AA)在水溶液和离子液体1-乙基-3-甲基咪唑(EMIMBF4)中的电化学行为.AA在EMIMBF4中与在水溶液中一样,不可逆氧化成脱氢抗坏血酸(DHAA).现场红外光谱结果表明,DHAA在水中迅速发生水解反应,而在EMIMBF4中则较稳定.在EMIMBF4中,AA的羰基峰出现在1739 cm-1处,DHAA的羰基峰出现在1785 cm-1处,它们相比于游离态的羰基发生了红移.原因可能是AA和DHAA与EMIMBF4间易形成氢键,或者是AA自身形成了氢键,DHAA以二聚体的形态存在.     

离子热合成磷铝分子筛

AlPO-11 molecular sieve with AEL structure was ionothermally synthesized using ionic liquid solvent as medium. The effects of ionic liquid amount, synthesis time and temperature were investigated. The structure and characteristics of molecular sieve samples were characterized by X-ray diffraction(XRD)，scanning electron microscopy (SEM), thermo gravimetric analysis(TGA). The results indicate that AlPO-11 molecular sieve could be synthesized by 1-ethyl-3-methylimidazolium bromide ([Emim]Br) ionic liquid as both the solvent and template.     

Liquid-liquid interfacial tension of equilibrated mixtures of ionic liquids and hydrocarbons

Ionic liquids are possible alternative solvents for the separation of aromatic and aliphatic hydrocarbons by liquid-liquid extrac- tion. Interfacial tension is an important property to consider in the design of liquid-liquid extraction processes. In this work, the liquid-liquid interfacial tension and the mutual solubility at 25 °C have been measured for a series of biphasic, equilibrated mixtures of an ionic liquid and a hydrocarbon. In particular, the ionic liquids 1-alkyl-3-methylimidazolium bis(trifluorome- thanesulfonyl)imide (with the alkyl substituent being ethyl, hexyl or decyl), 1-ethyl-3-methylimidazolium ethylsulfate, and 1-ethyl-3-methylimidazolium methanesulfonate have been selected, as well as the hydrocarbons benzene, hexane, ethylben- zene, and octane. The selected sets of ionic liquids and hydrocarbons allow the analysis of the influence of a series of effects on the interfacial tension. For example, the interfacial tension decreases with an increase in the length of the alkyl substituent chain of the cation or with an increase of the degree of charge delocalisation in the anion of the ionic liquid. Also, the interfa- cial tension with the aromatic hydrocarbons is markedly lower than that with the aliphatic hydrocarbons. A smaller effect is caused by variation of the size of the hydrocarbon. Some of the observed trends can be explained from the mutual solubility of the hydrocarbon and the ionic liquid.     

A mild ring opening fluorination of epoxide with ionic liquid 1-ethyl-3-methylimidazorium oligo hydrogenfluoride (EMIMF(HF)2.3)

Ring opening fluorination of epoxides with hydrogen fluoride in ionic liquid 1-ethyl-3-methylimidazorium oligo hydrogenfluoride EMIMF(HF)_2.3 was demonstrated. This ionic liquid released hydrogen fluoride graduately to make mild conditions without oligomerization of epoxides.     

An efficient one-pot synthesis of 3-glyoxylic acids of electron-deficient substituted azaindoles by ionic liquid imidazolium chloroaluminate-promoted Friedel-Crafts acylation

An efficient, one-pot Friedel-Crafts acylation/hydrolysis reaction promoted by the acidic ionic liquid 1-ethyl-3-methylimidazolium chloroaluminate (generated from 1-ethyl-3-methylimidazolium chloride (EmimCl) and aluminum chloride (X(AlCl₃), mole fraction X = 0.75) for the formation of 3-glyoxylic acid derivatives of electron-deficient, substituted 4- and 6-azaindoles is described.     

离子液体/凝胶聚合物电解质的制备及其与LiFePO_4的相容性

以1-甲基-3-乙基咪唑六氟磷酸盐(EMIPF6)、聚偏氟乙烯-六氟丙烯(P(VDF-HFP))和六氟磷酸锂(LiPF6)为原料,采用溶液浇铸法制备了离子液体/凝胶聚合物电解质(ILGPE).通过循环伏安(CV)、计时电流法、恒流充放电、电化学阻抗法(EIS)研究了该电解质的离子传输特性以及与锂离子电池正极材料LiFePO4的相容性.结果表明,离子液体/凝胶聚合物电解质的室温电导率为1.650×10-3S·cm-1,电化学稳定窗口达到5.0V.在充放电循环过程中,电极表面形成的钝化膜改善了锂离子脱、嵌可逆性和电极/电解质的界面性质.     

Liquid–liquid equilibrium and interfacial tension of the ternary system heptane + thiophene + 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide

The liquid–liquid equilibrium (LLE) of the ternary system comprising heptane, thiophene and the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C₂mim][NTf₂]) was determined at 25 °C and atmospheric pressure, for preliminary evaluation of the potential of this ionic liquid as solvent for the desulfurisation of transportation fuels. Classical parameters such as solute distribution ratio and selectivity were calculated from the LLE data and subsequently analysed. The LLE data were also correlated by means of the ‘Non-Random Two-Liquid’ (NRTL) equation. Besides the LLE, another critical property for the design of extraction processes, namely the interfacial tension, was determined in parallel, throughout the immiscibility domain of the ternary system. For the first time, the LLE and the interfacial tension of a ternary system involving an ionic liquid are jointly reported.     

Development of an ionic liquid-based dispersive liquid-liquid micro-extraction method for the determination of phthalate esters in water samples

Ionic liquid-based dispersive liquid-liquid micro-extraction (IL-DLLME) was coupled with high-performance liquid chromatography-ultraviolet (HPLC-UV) for the determination of four phthalate esters, including butyl benzyl phthalate, di-n-butyl phthalate, dicyclohexyl phthalate and bis(2-ethylhexyl) phthalate in water samples. The mixture of ionic liquid (IL) and dispersive solvent was rapidly injected into 10 mL aqueous sample. Then, IL phase was separated by centrifugation and was determined by high-performance liquid chromatography-ultraviolet. The factors influencing the extraction efficiency, such as type and volume of IL, disperse solvent, extraction time, centrifuging time and ionic strength, were investigated and optimized. Under the optimized conditions, the extraction recoveries by the proposed ionic liquid-based dispersive liquid-liquid micro-extraction for the four phthalates ranged from 83.0 to 91.7%. The relative standard deviations were between 7.8 and 15%. The limits of quantification for four phthalates were between 10.6 and 28.5 μg/L. The proposed method was successfully applied for the analysis of PAEs in tap, lake and treated wastewater samples.     

镁合金于离子液体中电镀铝之研究

本研究利用AlCl3-EMIC离子液体在AZ91D镁合金表面电镀铝金属,探讨离子液体组成及电流密度对电镀层性质的影响.研究结果显示铝金属可以成功地电镀于AZ91D镁合金表面上.在-0.2 V的电位下,在60 m/o AlCl3离子液体中可以获得较佳的电镀铝层.另外,在低定电流密度下进行电镀,电流效率较佳,镀层较厚.于3.5%NaCl(by mass)溶液中,铝金属镀层可以大幅提升镁合金之开路电位,并使其表面活性下降.电化学交流阻抗频谱分析显示,镁合金裸材于3.5%NaCl(by mass)水溶液中之极化阻抗值约为470~510Ω.cm2,镀铝之镁合金极化阻抗值则可提升至5200Ω.cm2.极化曲线则显示,镀铝之镁合金可以被钝化,其钝化电流密度低至5×10-5A/cm2.     

一种室温离子液体与水相互作用的密度泛函理论研究

采用量子化学计算中的密度泛函理论(DFT),在B3LYP/6-31+G(d,p)计算水平上研究了离子液体1-乙基-3-甲基咪唑四氟硼酸盐([Emim]BF4)及其与水分子形成的复合物的稳定构型和相互作用能;经振动频率分析得到了[Emim]BF4及其与水的复合物的红外光谱.计算结果表明,相对于水分子与阳离子的作用而言,水分子与阴离子的作用对离子液体结构的影响更大.与此同时,实验测得的[Emim]BF4的红外光谱与计算结果吻合.