具有低表面自由能有机介电薄膜的制备及表征

通过自主开发的有机镀膜技术在Mg-Mn-Ce镁合金表面制备了具有低表面自由能和较高介电常数的有机纳米薄膜. 利用X射线光电子能谱(XPS)分析了表面有机镀膜过程的反应机理, 借助傅里叶变换红外(FT-IR)光谱进一步确认表面有机膜层的存在, 采用接触角测量仪测定了有机薄膜的蒸馏水接触角和表面自由能变化, 使用椭圆偏振光谱仪研究了薄膜的厚度, 并借助精密阻抗分析仪评价了薄膜的介电性能. 有机镀膜后镁合金表面形成了一层纳米级厚度的有机薄膜, 接触角从基体的70.8°上升至150.5°, 表面自由能从基体的37.96 mJ·m^-2降低到1.57 mJ·m^-2, 镁合金表面从亲水性转变为疏水性; 薄膜的厚度和质量随有机镀膜时间延长先增加后有所减小, 在镀膜20 min时薄膜性能最佳, 此时膜重达到23.5 μg·cm^-2, 膜厚最大为147.48 nm, 其相对介电常数也达到最大, 在1 kHz下可达24.922.     

氟硅烷自组装单分子膜的制备及其摩擦学性能

利用分子自组装技术制备了全氟辛酰胺丙基硅烷单分子膜,用X射线光电子能谱(XPS)对组装膜的表面元素进行了表征;接触角测试表明,该组装膜具有很好的疏水疏油性,其对水的接触角高达105°,对正十六烷的接触角为50°.摩擦磨损实验结果表明,全氟辛酰胺丙基硅烷自组装单分子膜可以大大降低基片的摩擦系数,使载玻片的摩擦系数从0.85左右降低到0.14左右,而且低负荷下具有很好的耐磨性.     

疏水介孔二氧化硅膜的制备与表征

用甲基三乙氧基硅烷(MTES)代替部分正硅酸乙酯(TEOS)作为前驱体，以聚乙烯醚-聚丙烯醚-聚乙烯醚三嵌段共聚物(P123)作有机模板剂，通过共水解缩聚反应制备了甲基修饰的介孔SiO₂膜。利用N₂吸附、FTIR、²⁹Si MAS NMR以及接触角测量仪对膜的孔结构和疏水性进行了表征。结果表明，修饰后的膜材料具有良好的介孔结构，最可几孔径为4.65 nm，孔体积为0.69 cm³·g^-1，比表面积为938.4 m²·g^-1；同时疏水性明显提高，当n_MTES/n_TEOS达到1.0时，其对水的接触角达到109°± 1.1°。气体渗透实验表明气体通过膜孔的扩散由努森机制所控制。     

不同链长二元混合自组装薄膜的制备及其微观摩擦性能研究

采用分步组装的方法,将正己酰氯、正癸酰氯、正十四碳酰氯和硬脂酰氯按不同比例混合,接枝到3-(三甲氧基硅烷基)丙基乙烯基二胺(DA)氨基自组装膜表面,制备出一系列不同链长二元混合自组装薄膜;通过调节溶液中二元组分的相对比例,得到一系列不同厚度和不同表面润湿性的纳米有机薄膜;对薄膜进行了接触角测量、椭圆偏光测厚以及原子力形貌分析,并用摩擦力显微镜考察了其摩擦学性能.没有发现相分离现象,而且研究发现,随着长碳链分子所占比例的增大,薄膜的致密度增加,表面疏水性能增强,微观摩擦系数也随之减小.     

氟硅改性聚氨酯自组装膜的合成及性能

以甲苯二异氰酸酯、聚酯二元醇、2,2-二羟甲基丙酸和十三氟-1-辛醇等为原料合成了氟醇封端的聚氨酯预聚体(FPU)。 通过FPU侧链含有的羧基官能团与异氰酸酯基硅烷偶联剂(Si-NCO)反应制备了含硅氧烷官能团功能性树脂(FPUSi)。 采用红外光谱(FT-IR) 对产物结构进行了表征,用TGA和水接触角等测试了自组装薄膜的表面性能。 结果表明,在N2气氛围下,FPU和FPUSi的热失重温度（T5％）均为178 ℃;硅基表面经FPUSi自组装膜修饰后,其表面水接触角达到81°。 微摩擦测试结果表明,当载荷为400 mN时,FPUSi自组装薄膜的稳定摩擦系数达到0.09。     

纳米多孔结构镍基复合膜电极的电化学法制备及其电容特性

通过对电沉积法得到的Ni-Cu合金镀层进行电化学去合金化处理, 制备了纳米多孔结构金属镍膜. 采用循环伏安法对多孔金属镍膜在1 mol·L^-1 KOH溶液中进行阳极氧化处理, 获得了纳米多孔结构的镍基复合膜电极. 应用扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和电化学技术对所制备的膜电极的物理性质及赝电容特性进行了表征. SEM、XRD和XPS的测试结果表明, 所制备的纳米多孔结构镍基复合膜由Ni、Ni(OH)₂和NiOOH组成. 电化学实验结果显示, 该复合膜在20 A·g^-1的充放电电流密度下, 给出了578 F·g^-1的初始比电容; 在1000次充放电循环后, 它的比电容值为544 F·g^-1, 电容保持率为94%. 纳米多孔结构有利于KOH电解液的渗透, 从而促进反应物种在电极内部的传输; 纳米多孔的金属镍基体可以提高Ni(OH)₂膜的电子导电性; 纳米大小的Ni(OH)₂颗粒能够缩短质子的固相扩散路径. 上述因素是所制备的纳米多孔结构镍基复合膜电极具有优异赝电容特性的主要原因.     

硅表面复合自组装膜的制备及其摩擦性能

采用自组装技术在单晶硅表面制备了3-氨基丙基三乙氧基硅烷(APTES)-SiO2-APTES复合膜,并对其表面的组成、结构及摩擦性能进行了表征.结果表明:复合膜表面对水的接触角约为63°,且表面平整、致密,其平均粗糙度(Ra)约为0.963nm.通过原子力显微镜(AFM)和透射电子显微镜(TEM)观察到夹层中SiO2颗粒的粒径约为20-50nm,较均匀地分布在第一层APTES膜的表面.与APTES自组装单层膜(SAMs)相比,APTES-SiO2-APTES复合膜由于纳米SiO2颗粒的引入而表现出更低的摩擦系数和更长的耐磨寿命.     

氟硅烷自组装单分子膜的制备及其摩擦学性能

利用分子自组装技术制备了全氟辛酰胺丙基硅烷单分子膜,用X射线光电子能谱(XPS)对组装膜的表面元素进行了表征;接触角测试表明,该组装膜具有很好的疏水-疏油性,其对水的接触角高达105°,对正十六烷的接触角为50°.摩擦磨损实验结果表明,全氟辛酰胺丙基硅烷自组装单分子膜可以大大降低基片的摩擦系数,使载玻片的摩擦系数从0.85左右降低到0.14左右,而且低负荷下具有很好的耐磨性.     

2，9，16，23-四羧基酞菁钴(Ⅱ)与硫醇、硫酚配位反应的热力学研究

我们研究了2,9,16,23-四羧基酞菁钴(Ⅱ)与硫醇(2-巯基乙醇)、硫酚(苯硫酚)轴向配位反应的热力学性质,发现了配位过程中中心离子钴由二价变为一价的现象。用紫外-可见分光光度法和Miller-Dorough数据处理方法,确定了体系的配位数和平衡常数;利用温度系数法求得了体系的Δ_rH^?_m, Δ_rS^?_m。探讨了温度对反     

侧链型磺化聚芳醚酮/磺化聚乙烯醇复合型直接甲醇燃料电池用质子交换膜

通过溶液共混法制备了不同磺化聚乙烯醇(SPVA)含量的侧链型磺化聚芳醚酮/磺化聚乙烯醇(S-SPAEK/SPVA)复合膜. 应用红外光谱(FTIR)对复合膜进行了表征, 扫描电镜(SEM)显示SPVA均匀分布在复合膜中. 通过对复合膜的性能测试发现该系列复合膜具有良好的热性能、较高的吸水率和保水能力. SPVA中的羟基能有效地阻碍甲醇的透过, 甲醇渗透系数从S-SPAEK/SPVA5 复合膜的7.9×10^-7 cm²·s^-1降低到S-SPAEK/SPVA30的1.3×10^-7 cm²·s^-1, 比S-SPAEK膜的11.5×10^-7 cm²·s^-1降低了一个数量级. SPVA的引入增加了亲水基团数量, 增加了复合膜的吸水和保水能力, 有利于质子按照“Vehicle”机理和“Grotthuss”机理进行传递, 柔软的SPVA链段与S-SPAEK侧链聚集成亲水相区, 形成连续的质子传输通道, 提高了复合膜的质子传导率. 在25 和80℃ 时, S-SPAEK/SPVA30 复合膜的质子传导率分别达到了0.071 和0.095 S·cm^-1. 可见,S-SPAEK/SPVA复合膜有望在直接甲醇燃料电池中得到应用.     

Study on triazine thiols. VI. Selective graft copolymerization of MMA on modified copper plates

Graft copolymerization of MMA on copper surface which is initiated by Na₂S₂O₈ in an aqueous solution proceeded selectively when copper plates are modified by 6-unsaturated group-1,3,5-triazine-2,4-dithiol monosodium salts (UTD) and 6-dimethylamino-1,3,5-triazine-2,4-dithiol monosodium salt (DMTD). Grafting weight was influenced by the molar ratio of UTD to DMTD in the aqueous solution that copper plates are treated. The former on copper surface is a coupling component of MMA radicals and initiator radicals. The latter is a catalyst which accelerates the formation of radicals acting with Na₂S₂O₈. Selective graft copolymerization is due to the reason that radicals generate selectively in the neighborhood of copper surface and in this place there are monomers such as MMA and UTD.     

Study on functionalization of metal surfaces. III. Photopolymerization of monomer films on metal surfaces

The three kinds of monomer films on metal surfaces were deposited by adsorption from a solution of 6-polymerizable substituents-1,3,5-triazine-2,4-dithiol monosodium salts (RTDN); the polymerizable substituents such as cis-9-octadecenylamino, di(cis-9-octadecenyl)amino, and p-vinylbenzyl(cis-9-octadecenyl)amino groups were selected in view of the polymerization activity of unsaturated groups in the substituents and the packing degree of monomer molecules. The monomer films were estimated to consist of mainly 6-substituents-1,3,5,-triazine-2,4-dithione (3H, 5H) and to be multimolecular layers that are considerably cross-packed and ordered. The monomer films on metal surfaces were polymerizable under a UV light irradiation in air atmosphere to give polymer films. In the photopolymerization, azobis(isobutyronitrile) (AIBN) was very effective for increasing the monomer conversion and the polymerization rate. The optimum concentration of AIBN in monomer films was very small, about 0.025 mol %. The monomer conversion was influenced by the kind of monomers, namely, the polymerization activity and the packing degree. The effect of the packing degree was especially remarkable. The monomer conversion decreased with an increase in the thickness of monomer films. This is because the polymerization was initiated by oxygen and AIBN, which were diffused into the inner of monomer films. The possibility of polymerization of the unsaturated groups and the thione groups in monomer molecules under UV light irradiation is discussed.     

Syntheses,characterizations and crystal structures of triorganotin(IV) complexes with amine derivatives of 6-amino-1,3,5-triazine-2,4-dithiol

Four new triorganotin(IV) complexes: Me₃SnL¹SnMe₃ (1), Ph₃SnL¹SnPh₃ (2), [Me₃SnL²] _n (3), Ph₃SnL²SnPh₃ (4) have been synthesized from 6-anilino-1,3,5-triazine-2,4-dithiol (L¹H₂) and 6-(dibutylamino)-1,3,5-triazine-2,4-dithiol (L²H₂). All were characterized by elemental analyses, IR and NMR spectra and X-ray diffraction analyses. Crystal structures show that 1, 2 and 4 are monomers with one ligand coordinated to two triorganotin moieties; complex 3 is a helical chain. Significant C–H ··· π, N–H ··· π interactions and intermolecular hydrogen bonds stabilize these structures.     

Surface plasmon resonance and electrochemistry characterization of layer-by-layer self-assembled DNA and Zr4+ thin films, and their interaction with cytochrome c

Through electrostatic layer-by-layer (LbL) assembly, negatively charged calf thymus double stranded DNA (CTds-DNA), and positively charged Zr⁴⁺ ions were alternately deposited on gold substrate modified with chemisorbed cysteamine. Thus-prepared three-dimensional DNA networks were characterized by surface plasmon resonance (SPR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS). SPR spectroscopy indicates that the effective thickness of DNA monolayer in the (DNA/Zr⁴⁺)₁ bilayer was 1.5 ± 0.1 nm, which corresponds to the surface coverage of 79% of its full packed monolayer. At the same time, a linear increase of film thickness with increasing number of layers was also confirmed by SPR characterizations. The data of XPS and IR-RAS show that Zr⁴⁺ ions interact with both the phosphate groups and nitrogenous bases of DNA and load into the framework of DNA. Furthermore, the interactions between this composite film and heme protein cytochrome c (Cyt c) were investigated by SPR spectroscopy and electrochemistry. Compared with the adsorption of Cyt c on DNA monolayer, this composite multilayer film can obviously enhance the amount of immobilized Cyt c confirmed by SPR reflectivity-incident angle (R-θ) curves. Cyclic voltammetry (CV) indicates the Cyt c adsorbed on the composite film is electroactive, and the enhancement of peak current in CV indirectly verifies the increase of the amount of immobilized Cyt c.     

Synthesis, crystal structures, electrochemical and spectroscopic properties of ruthenium(II) complexes containing diamino-1,3,5-triazine derivatives

Three Ru(II) complexes [Ru(bpy)₂(1-IQTNH)](ClO₄)₂ (1), [Ru(bpy)₂(2-QTNH)](ClO₄)₂ (2) and [Ru(bpy)₂(3-IQTNH)](ClO₄)₂ (3) (bpy = 2,2′-bipyridine, 1-IQTNH = 6-(isoquinolin-1-yl)-1,3,5-triazine- 2,4-diamine, 2-QTNH = 6-(quinolin-2-yl)-1,3,5-triazine- 2,4-diamine, 3-IQTNH = 6-(isoquinolin-3-yl)-1,3,5-triazine-2,4-diamine) have been synthesized and characterized by elemental analysis, ¹H NMR spectroscopy, electrospray ionization mass spectrometry and X-ray crystallography. The electrochemical and spectroscopic properties of the complexes differ from those of [Ru(bpy)₃]²⁺ owing to the structural differences between the ligands and their complexes.     

含氟硅丙烯酸酯乳液超疏水膜中疏水基团的梯度分布与表面微观结构研究

利用含氟疏水基团的梯度分布,结合草莓形纳米SiO2粒子提供的双重粗糙表面,制备了具有类"荷叶效应"的超疏水涂膜,水接触角达(174.2±2)°,滞后角几乎接近0°.通过原子力显微镜、扫描电镜和水接触角的测试对膜表面形貌及疏水性能进行了表征;探讨了其表面微观结构与表面疏水性能的关系.草莓形复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度,使水滴与涂膜表面接触时能够形成高的空气捕捉率,这种微观结构与疏水基团的梯度分布相结合,赋予了含氟硅丙烯酸酯乳液涂膜表面超疏水性能.     

Fabrication and mechanical durability of a superhydrophobic copper surface with morphological development from hydrothermal reaction

The superhydrophobic surface on copper is fabricated by using a simple hydrothermal reaction and subsequent perfluorosilane treatment. The micro‐structured and nano‐structured surface was directly obtained through the hydrothermal reaction of copper sheets with sulfur at 180 °C for 12 h, resulting in the formation of copper sulfide film on the copper substrate. The chemical composition of this film was confirmed using X‐ray photoelectron spectroscopy. After copper sulfide film is treated by perfluorosilane, the superhydrophobic surface with static water contact angle of 153 °C and a low contact angle hysteresis is achieved. The superhydrophobic surface shows strong mechanical stability and can effectively protect the copper substrate. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and Characterization of Ag2 O/Organicsilicone Self-assemblied Composite Film

The composite film of nanometer AgO2/silane coupling reagent aminopropyltriethoxy-silane (CH3O)3Si(CH2)3NH2was prepared on single-crystal silicon by the self-assembly of silane on the hydroxylated substrate followed with the deposition of nanometer AgO2 on the silane SAMs from an aqueous Ag2O gel. The resultant composite film was characterized by means of X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The contact angles of distilled water on the silane SAMs and the composite film were measured to compare the surface states. The experiment shows that the nanometer Ag2O can be easily incorporated in the silane SAMs and lead to changed surface state of the composite film. Nanometer Ag2O crystallites in a size of about 20 nm distribute quite uniformly in the composite film. It was anticipated that the composite film might find application to the protection of single-crystal Si substrate in MEMS devices and also propose a novel single electron device structure based on nanoscale Ag2O colloidal particles.     

Oxidation of 2-Chloro-1-phenylethane-1,1-dithiol

Oxidation of 2-chloro-1-phenylethane-1,1-dithiol with bromine, iodine, and elemental sulfur, as well as under UV irradiation, leads to formation of 1,4-bis(chloromethyl)-1,4-diphenyl-2,3,5,6-tetrathiane in 50–95% yield. Oxidation of the same substrate with selenium dioxide gives 1,5-bis(chloromethyl)-1,5-diphenyl-2,4-dithia-3-selenapentane-1,5-dithiol. On heating to 60°C, the latter loses selenium to afford 1,4-bis-(chloromethyl)-1,4-diphenyl-2,3-dithiabutane-1,4-dithiol.     

Porous and electrically conductive polypyrrole-poly(vinyl alcohol) composite and its applications as a biomaterial

Bulk modification of polypyrrole (PPY) with poly(vinyl alcohol) (PVA) was carried out by the electropolymerization of pyrrole in the presence of PVA in the reaction solution, with tetraethylammonium perchlorate (TEAP) as the electrolyte. The surface morphology of the as-synthesized PPY-TEAP-PVA film was investigated using scanning electron microscopy, and the film was further characterized using X-ray photoelectron spectroscopy, electrical conductivity, the water contact angle, and BET surface area measurements. The PPY-TEAP-PVA composite is electrically conductive, hydrophilic, and microporous with a high surface area. Its potential as a biomaterial was investigated with respect to its blood compatibility and function as a substrate for biosensor fabrication and cell culture. The presence of PVA in the film attenuates blood protein adsorption, and the porous nature of the PPY-TEAP-PVA film results in a 10-fold increase in the amount of glucose oxidase covalently immobilized on the film over that on a nonporous PPY film. PC12 cell attachment and growth on the PPY-TEAP-PVA film was also shown to be enhanced compared with that on tissue culture polystyrene. The attached cells proliferated and formed a monolayer on the film surface after 48 h of seeding.