铬和硫共掺杂二氧化钛催化剂的制备及其可见光催化性能

以钛酸四丁酯为前驱体,硝酸铬和硫脲为掺杂离子给体,通过溶胶-凝胶法成功制备了纯TiO2、不同浓度的铬掺杂和铬/硫共掺杂TiO2光催化剂.以靛红为目标污染物,进行了可见光催化降解活性测试实验.结果表明,共掺杂催化剂的活性高于未掺杂和单掺杂催化剂.当共掺杂催化剂含0.60%(原子比)的铬,1.2%(原子比)的硫,焙烧温度为500℃时具有最高的光催化降解活性.X射线衍射、N2吸附、X射线光电子能谱和紫外-可见漫反射吸收光谱表征结果显示,共掺杂催化剂为锐钛矿型,具有较高的比表面积,对可见光有较强的吸收能力.共掺杂TiO2具备较高可见光催化活性的原因可能是铬掺杂降低了TiO2的禁带宽度,拓展了可见光吸收区域,而硫掺杂能够维持体系的电荷平衡,增强催化剂对可见光的吸收.     

N掺杂TiO_2纳米粒子表面光生电荷特性与光催化活性

以尿素为氮源,采用水热法制备了不同N掺杂量的TiO2(N-TiO2)光催化剂.利用X射线衍射(XRD),紫外-可见漫反射光谱(UV-Vis DRS),X射线光电子能谱(XPS)及荧光(PL)光谱等技术对其进行了系统的表征.以罗丹明B(RhB)和甲基橙(MO)溶液的脱色降解为模型反应,分别考察了N-TiO2光催化剂在紫外和可见光区的光催化活性.利用表面光伏(SPV)和瞬态光伏(TPV)技术研究了N-TiO2纳米粒子表面光生电荷的产生和传输机制,并探讨了光生电荷与光催化活性之间的关系.结果显示,随着N含量的增大,TiO2表面光伏响应阈值红移,可见光部分光电压响应强度逐渐增强,瞬态光伏响应达到最大值的时间亦有着不同程度的延迟.这表明适量的N掺杂能够提高TiO2纳米粒子中光生载流子的分离效率,相应地延长载流子的传输时间,增加光生电荷的寿命,从而促进其光催化活性;而过量的N掺杂则增加了TiO2纳米粒子中光生载流子的复合中心,抑制其光催化活性.     

氮-硫共掺杂二氧化钛光催化剂的制备及其可见光催化活性

采用研磨煅烧法,以硫脲(TU)作为氮源和硫源,H2TiO3(HT)为TiO2的前驱体,制备了不同TU/HT比例的N,S共掺杂TiO2光催化剂(NS/TiO2);利用X射线衍射仪、透射电镜、X射线光电子能谱仪、拉曼光谱仪、紫外-可见吸收光谱仪等分析了NS/TiO2的晶体结构、显微形貌、典型元素的化学状态以及光谱性质;利用BET法测定了NS/TiO2的比表面积,同时测定了其在可见光照下催化降解罗丹明B的活性.结果表明,当TU/HT质量比为0.5时,NS/TiO2的光催化活性最佳,光照70min时的罗丹明B降解率为44.4%.氮元素以NH3形式吸附在TiO2表面,硫元素以S6+形式存在,部分S6+取代Ti 4+的位置.与此同时N,S共掺杂使得TiO2的禁带宽度减小,可见光催化活性提高.     

可见光响应的硫掺杂TiO2的制备、表征及其光催化活性

采用溶胶-凝胶法制备了硫掺杂TiO2光催化剂粉末.光催化降解罗丹明B实验结果表明,钛酸四丁酯与硫脲的摩尔比Ti/S=2.7∶ 1,经600℃热处理后光催化活性最佳.通过紫外可见漫反射吸收光谱(DRS)、X-射线衍射(XRD)、X-射线光电子能谱(XPS)、傅立叶变换红外光谱(FT-IR)以及表面光电压谱(SPS)等研究结果表明,适量的硫掺杂导致TiO2有效地抑制晶相转变.在热处理过程中由S2-被氧化为S4+并进入TiO2晶格中取代部分Ti4+,发生晶格畸变,带隙变窄,使催化剂吸收光谱红移至550 nm,诱发可见光活性.     

Sm掺杂对TiO2薄膜光催化性能的影响

 采用溶胶-凝胶法、浸渍-提拉法制备了不同形式和不同含量Sm掺杂的锐钛矿晶型TiO2的光催化剂薄膜. 采用X射线衍射、UV-Vis光谱及电化学实验对所制得的TiO2光催化剂薄膜进行了表征,并通过甲基橙溶液的光催化降解实验评价了其光催化活性. 结果表明,与未掺杂的TiO2薄膜相比,Sm掺杂的TiO2薄膜的UV-Vis吸收光波长向长波方向移动,并且光照开路电压也相应提高; 适量Sm掺杂可以明显提高TiO2薄膜的光催化活性,最佳Sm掺杂量为x(Sm3+)=0.5%; 在各种掺杂形式中以表层Sm掺杂的Sm-TiO2(S)薄膜的光催化活性最好. 讨论了Sm掺杂提高TiO2薄膜光催化活性的机理.     

镧系离子掺杂TiO2的制备及其对咪唑降解反应的光催化活性

 以TiCl4和镧系元素的氯化盐溶液为前驱体,采用溶胶-凝胶法制备了不同含量镧系离子掺杂的TiO2光催化剂,用X射线衍射(XRD)、 光致发光光谱(PLS)、 表面光电压谱(SPS)和X射线光电子能谱(XPS)对催化剂进行了表征. XRD结果表明,样品为锐钛矿和金红石的混晶相,镧系离子未进入到TiO2晶格中. PLS和SPS测定结果表明,随着掺杂离子的不同和掺杂含量的不同,样品的谱强度呈现有规律的变化. 在紫外光照射下,以咪唑为目标降解物比较了催化剂的光催化活性. 结果表明,适当含量的镧系离子掺杂可有效促进TiO2表面光生载流子的分离,从而显著提高其光催化活性.     

硼硫共掺杂TiO2的光催化性能及掺杂机理

采用水热法制备了硼硫共掺杂的TiO2光催化剂(TiO2-B-S),并用其光催化降解甲基橙.结果表明,在240℃下水热反应12h时制得的TiO2-B-S具有较高的催化活性,紫外光照射50min和太阳光照射230min时对甲基橙的降解率分别达99.8%和81%.X射线粉末衍射、紫外-可见漫反射光谱和X射线光电子能谱等研究表明,TiO2-B-S为锐钛矿晶型,硫硼掺杂能抑制TiO2粒径的生长;TiO2-B-S同时具有较高的紫外光和可见光活性的原因可能是掺杂的硼以B3 进入晶格中,导致TiO2晶格畸变,带隙变窄.掺杂的硼和硫还提高了TiO2的表面酸度和对可见光的吸收.     

浓度梯度分布的镍和氮共掺杂TiO2光催化剂的制备和表征

以TiCl4为钛前驱体, 氨水和氯化镍为掺杂离子给体, 采用沉淀和层层浸渍相结合的方法制备了氮、镍共掺杂TiO2光催化剂. 采用X射线衍射(XRD)、氮气吸附-脱附、X射线光电子能谱(XPS)、紫外-可见漫反射吸收光谱(UV-Vis)等现代表征方法对催化剂的晶体结构、微结构、掺杂基团和光谱性质进行了表征. XRD和氮吸附-脱附分析结果表明, 氮、镍共掺杂TiO2为单一锐钛矿相, 具有介孔结构. XPS谱证实掺杂的氮和镍分别以NOx和Ni2O3及NiO的形式存在, 且镍在共掺杂表面的浓度高于体相中的浓度, 在扩散方向上存在浓度梯度分布. 4-氯酚的降解实验结果表明, 浓度梯度分布镍和氮共掺杂TiO2的紫外光-可见光催化活性均高于均相共掺杂TiO2、单掺杂和未掺杂TiO2的催化活性. 其原因是掺杂的氮以NOx形式存在, 使催化剂的感光范围拓展至可见光区; 而掺杂的镍维持了半导体体系的电荷平衡, 有效抑制了Ti3+的产生. 同时掺杂的镍在催化剂中存在浓度梯度分布, 减少了光生电子和空穴的复合几率, 提高了催化剂的光催化活性.     

S掺杂S-TiO_2/SiO_2可见光响应光催化剂的制备及性能

以四氯化钛为钛源,硫脲为硫源,采用液相水解-沉淀法制备了S掺杂的TiO2/SiO2(S-TiO2/SiO2)催化剂,并以苯酚为模型物,考察了催化剂在可见光区、紫外光区和太阳光下的光催化活性,以及催化剂的使用寿命和分离性能.采用X射线光电子能谱、傅里叶变换红外光谱、紫外-可见漫反射光谱、X射线衍射、透射电镜及N2吸附-脱附等技术对催化剂进行了表征.结果表明,S以+6价形式进入TiO2体相并置换晶格中的Ti4+,适量S掺杂的S-TiO2/SiO2在紫外光区、可见光区和太阳光下均表现出较高的光催化活性.SiO2与TiO2界面间有Ti-O-Si键形成,结合牢固.S掺杂在TiO2表面生成Ti-O-S键,形成新的能级结构,使光催化剂在450～550nm产生吸收,诱发TiO2可见光催化活性;同时提高了TiO2表面羟基数量.SiO2的加入可减小TiO2颗粒的平均尺寸,增大催化剂的比表面积,改善催化剂的分离性能,提高催化剂的使用寿命.     

钕掺杂提高TiO2光催化活性的机制

采用X射线衍射(XRD), BET吸附, X射线光电子能谱(XPS)表征了溶胶凝胶法制备的Nd掺杂TiO2光催化剂的晶体结构、表面电子结构与化学组成. 以甲基橙为有机底物, 测试Nd掺杂对光催化剂吸附性能和光催化活性的影响. 结果表明, Nd掺杂可阻碍TiO2的晶相转变, 减小光催化剂的晶粒尺寸, 比表面积增大. Nd掺杂提高光催化剂表面三价钛(TiⅢ)的含量及其对甲基橙的吸附能力是其提高TiO2光催化降解甲基橙活性的主要原因. Nd掺杂量为1.2%时, 光催化剂活性最高.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.