负载型金催化剂催化乙醇选择氧化反应

选择不同氧化物(Al2O3,SiO2,TiO2,MgO)和H-ZSM-5分子筛作为载体,以尿素为沉淀剂,采用沉积-沉淀法制备了一系列负载型金催化剂.采用X射线衍射、电感耦合等离子体发射光谱、程序升温还原、NH3程序升温脱附和透射电镜等技术对催化剂样品进行了表征,并测定了催化剂对乙醇选择氧化反应的催化性能.选择Au/Al2O3催化剂,考察了金负载量、反应条件(温度、压力、时间)和添加剂对乙醇选择氧化反应的影响.结果表明,所制备的Au/Al2O3催化剂的金负载率较高,金粒子较小(3～4 nm)且分布均匀.载体对金催化剂催化乙醇氧化反应有显著影响,主要产物为乙醛、乙酸乙酯和缩醛.以TiO2为载体时,乙醇转化率较高.以Al2O3为载体时,乙酸乙酯选择性较高;少量碱性添加剂可抑制缩醛的生成,并可提高乙醇转化率和乙酸乙酯选择性.在优化的条件下,乙醇转化率可达4.7%,乙酸乙酯选择性可达93.5%.     

担载纳米金催化乙醇选择氧化制乙酸乙酯

采用溶胶-凝胶法制备了一系列担载纳米金催化剂，用以催化乙醇选择氧化反应，模板剂的引入改变了催化剂载体的结构，从而提高了其催化活性和对乙酸乙酯的选择性，同时考察了反应温度、时间、以及催化剂制备方法对乙醇选择氧化反应的影响，实验结果表明使用以焙烧处理除去模板剂十八胺的Au／SiO2-O(C)为催化剂时，乙醇选择氧化一步制取乙酸乙酯的效果最佳，其选择性最高可达88．1％。     

焙烧方法和焙烧条件对纳米Au/HZSM-5催化剂金粒径和催化性能的影响

采用负压沉积沉淀法制备了纳米Au/HZSM-5催化剂前体,研究了深床焙烧和等离子体焙烧两种方法,以及焙烧温度和焙烧气氛对催化剂中纳米金粒径和催化性能的影响,并采用ICP、TEM、XRD、UV-vis、XPS等表征方法对催化剂金粒子进行了物化性能表征,采用合成气羰基化制乙酸甲酯反应表征催化性能。结果表明,不同焙烧方法和不同焙烧温度及气氛对负载型纳米Au/HZSM-5催化剂中金粒径、形貌、物化性质和催化性能有明显影响。其中,以等离子体焙烧方法在500℃氮气气氛下制备的纳米1.86%Au/HZSM-5催化剂中的金粒径最小,为2-5 nm。用于催化合成气羰基化制乙酸甲酯反应,原料中CO的转化率为67%,乙酸甲酯选择性可达78%。     

环己酮肟在B2O3/Al2O3-TiO2催化剂上的气相Beckmann重排反应

制备了B2O3/Al2O3-TiO2复合载体催化剂,并考察了其对环己酮肟气相Beckmann重排制己内酰胺反应的催化性能. 结果表明,载体中TiO2的含量、B2O3的负载量、载体的预处理温度及催化剂的焙烧温度等均对催化剂的性能产生明显的影响. 当载体中TiO2含量为60%,B2O3负载量为20%,催化剂经350 ℃焙烧时,环己酮肟的气相Beckmann重排反应的转化率和选择性很高. 用BET,NH3-TPD,XRD和IR等方法对催化剂的织构、表面酸性和晶相等进行了表征,并与催化剂的活性进行了关联,表明催化剂表面中等强度的酸中心浓度与催化剂的选择性具有对应关系.     

环已酮肟在B2O3／Al2O3—TiO2催化剂上的气相Beckemann重排反应

制备了B2O3/Al2O3-TiO2复合载体催化剂,并考察了其对环已酮肟气相Beckemann重排制已内酰胺反应的催化性能。结果表明,载体中TiO2的含量、B2O3的负载量、载体的预处理温度及催化剂的焙烧温度等均对催化剂的性能产生明显的影响。当载体中TiO2含量为60%,B2O3负载量为20%,催化剂经350℃焙烧时,环已酮肟的气相Beckemann重排反应的转化率和选择性很高。用BET,NH3-TPD,XRD和IR等方法对催化剂的织构、表面酸性和晶相等进行了表征,并与催化剂和活性进行了关联,表明催化剂表面中等强度的酸中心浓度与催化剂的选择性具有对应关系。     

Au/Fe2O3催化剂的制备及其对富氢气体中一氧化碳选择性氧化的催化性能

 采用共沉淀法制备了1.5%Au/Fe2O3催化剂,考察了加料方式对Au/Fe2O3催化剂化学组成及其催化富氢气体中CO选择性氧化性能的影响. 结果表明,正加法制备的Au/Fe2O3催化剂的性能明显好于反加法制备的催化剂,80 ℃时前者对富氢气体中CO选择性氧化反应的转化率为94%,CO2选择性为65%,连续反应10 h,催化剂活性没有变化. XRD,XPS和TEM等的测试结果表明,正加法制备的Au/Fe2O3催化剂中金粒子的平均粒径为2～4 nm,金粒子高度分散在载体上,并与载体之间发生了较强的相互作用,从而表现出较高的催化性能.     

无碱条件下Au/ZnO选择性催化氧化1,3-丙二醇合成3-羟基丙酸甲酯

采用溶胶-沉积法合成了高选择性的Au/ZnO催化剂,用于1,3-丙二醇选择性氧化酯化为3-羟基丙酸甲酯的反应.研究了保护剂PVA用量、金溶胶合成温度、金负载量及催化剂循环利用对反应的影响,且优化了反应温度和反应压力,并对催化剂进行了XRD和TEM表征.结果表明,PVA∶Au(m/m)=1∶4、金溶胶合成温度25℃、金负载量1%的Au/ZnO对目标反应的催化活性最好,在100℃和Po2=2MPa的条件下1,3-丙二醇的转化率达82.8%,产物3-羟基丙酸甲酯的选择性达95.4%.Au纳米粒子的粒径影响催化性能,在Au平均粒径为2.8~6.1nm的范围内,产物选择性随Au纳米粒子的粒径的减小而增大,平均粒径在2.8~4.8nm的范围内时,催化剂具有较好的产物选择性(大于90%);Au/ZnO催化剂循环利用4次后催化性能(转化率和选择性)无明显下降;并推测了无碱条件下Au/ZnO选择性催化氧化1,3-丙二醇合成3-羟基丙酸甲酯的反应机制.     

金属载体强相互作用增强Au/TiO2催化剂在3-硝基苯乙烯选择性加氢反应的活性

自Haruta与Hutchings于上世纪八十年代末发现金纳米催化剂优异的反应活性以来,科研人员对金催化的应用领域进行了广泛而深入地研究.对金催化科学和应用领域的研究一直在进行.大量的研究表明,金催化剂在各种选择性氧化反应中具有优异的催化性能(高活性和高选择性).然而,在催化加氢反应中,尽管金催化剂相比于铂族金属显示出优越的选择性,但是由于金催化剂选择性加氢反应的活性较差,使其在选择性催化加氢反应中的应用受到了极大的限制.研究表明,金催化剂较弱的活化氢气能力是其催化加氢反应活性低的主要原因.研究发现,氢气活化的活性中心可能是界面、负价金、低配位的金原子等.金催化剂具有明显的载体效应,金属-载体之间的相互作用能够显著地改变金催化剂的催化性能.Tauster等研究发现,铂族金属与还原性载体之间存在强相互作用,能够引发载体包覆金属表面,并且使得电子从载体向金属迁移,导致金属带负电.受金属-载体强相互作用(SMSI)效应的启发,本文探究了Au/TiO2催化剂中SMSI对金催化剂加氢性能的影响.在H2或O2气氛下高温焙烧Au/TiO2,获得一系列金催化剂(Au/TiO2-TA,T为焙烧温度(oC):300、400、500和600;A为气氛:H2或O2).对比在3-硝基苯乙烯(3-NS)选择性加氢反应中的活性发现,Au/TiO2-500H的TOF值是Au/TiO2-500O的3.3倍;动力学测试表明,Au/TiO2-500H和Au/TiO2-500O的反应表观活化能分别为79.5和105.1 kJ/mol.这表明两类催化剂催化活性中心的结构存在差异.X射线光电子能谱测试结果表明,Au/TiO2-H样品中Au带部分负电,而Au/TiO2-O中Au显示为金属态.HAADF-STEM和EELS显示,Au/TiO2-H中Au NPs的表面有TiOx物种,增加了Au-TiO2的界面.EPR结果表明,Au/TiO2-H中存在表面Ti3+物种,而Au/TiO2-O样品中则没有.为确认加氢反应的活性中心到底是界面还是负价金物种,本文探究了不同温度下氢气处理的Au/TiO2的结构与性能的关系,发现Au/TiO2-300H/400H/500H催化剂都显示出较好的催化3-NS加氢活性,而Au/TiO2-600H虽然具有更多的负价金物种,但是3-NS选择性加氢反应的活性反而降低,因此,负价金不是活性中心.这是因为不同温度处理的Au/TiO2-H样品中,SMSI的强弱不同,在300、400、500 oC下,SMSI能够增加Au-TiO2的界面长度,从而增强了3-NS加氢反应的活性;而温度达到600 oC,SMSI效应太强,Au NPs被包覆更密实,导致Au/TiO2-600H的3-NS选择性加氢反应的活性下降.密度泛函理论计算表明,Au/TiO2-H样品具有更低的H2解离活化能以及氢转移活化能.氢氘交换反应也进一步验证了SMSI有利于H2的活化.     

丙烯气相直接环氧化Au/TiO2催化剂的研究

在H2和O2共存条件下，金催化剂催化丙烯气相直接环氧化反应是近年来发展起来的一种新型环氧丙烷(PO)合成技术．本文采用沉积沉淀法制备了一系列Au／TiO2催化剂，考察了反应溶液的pH值、Au负载量、沉淀剂以及焙烧温度等因素对催化剂丙烯环氧化催化性能的影响．结果表明制备条件对催化性能有明显影响：反应溶液的pH值为7．5及Au负载量为2．4％时所得催化剂活性最好；当以Na2CO3、NaOH等含Na^ 物质作为沉淀剂时，催化性能明显优于Li^ 、K^ 等其它碱金属离子；400℃焙烧制得的催化剂活性较好，在50℃低温反应条件下，环氧丙烷得率可达1．3％．HRTEM结果表明，催化剂中Au组分高度分散于载体表面，且随着焙烧温度的增加Au粒因发生聚集而变大，从而影响了催化剂的活性．表面XPS分析证实，活性较好的Au／TiO2催化剂中活性组分Au除部分呈氧化态外，主要是以金属态的形式存在．     

金催化剂催化环己烷液相选择氧化研究

采用溶胶-凝胶法制备了一系列担载纳米金催化剂,用于催化环己烷液相选择氧化反应.在反应体系中没有加入任何溶剂或助催化剂,考察了反应温度、时间、压力和不同焙烧温度对催化剂活性的影响.实验结果表明,催化剂在250℃焙烧和金含量为0.032%时,环己烷选择氧化可以达到10.8%的转化率和90.8%的目的产物(环己醇和环己酮)选择性,相应转化频率高达5.2×104.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.