高性能纤维表面改性及其双马树脂基复合材料界面

采用电感耦合射频等离子体(ICP)和介质阻挡放电(DBD)低温等离子体对高性能连续纤维表面进行改性,分别采用X光电子能谱(XPS)、原子力显微镜(AFM)和动态接触角测定仪(DCA)等分析测试手段系统地研究了等离子体处理时间、放电功率、放电气压等对连续碳纤维、聚苯并二噁唑(PBO)纤维改性处理前后,纤维表面状态、表面组成、表面形貌、浸润性能的变化规律以及经等离子体处理前后纤维增强双马树脂基复合材料界面结构与性能的影响关系及变化规律、复合材料界面粘结和破坏机理.研究结果表明,经过等离子体处理后,纤维表面接枝上了大量的含羧基、羟基等极性官能团,表面粗糙度增加,表面自由能增加,纤维浸润性能得到明显改善,导致纤维与双马树脂基体界面层间剪切强度(ILSS)明显提高,复合材料的破坏模式由未处理的界面脱粘破坏转变为等离子体处理后的树脂基体破坏.最后,对纤维表面时效性及其对纤维增强双马树脂基复合材料界面性能的影响关系也进行了论述.     

表面改性对VGCF分散性质的影响

针对气相生长碳纤维极易团聚及与树脂基体界面结合能力较差的难题,采用双氧水-浓硝酸二步法对VGCF进行表面改性处理。利用X射线衍射仪、热重分析仪、傅立叶红外光谱仪、紫外可见分光光度计等测试分析了改性前后VGCF的表面结构和在溶剂中的分散性,并以形状记忆聚氨酯为基体,采用溶液混合法制备了气相生长碳纤维/形状记忆聚氨酯的复合材料,测试了复合材料的力学性能。经过改性后,VGCF的石墨晶型结构几乎没有改变,VGCF表面的含氧官能团浓度得到较大提高,且其在有机溶剂中的分散性及分散稳定性也得到很大提高;在气相生长碳纤维/形状记忆聚氨酯的复合材料截面中,扫描电镜观察表明表面改性使得VGCF在基体中的分散性及与基体的界面结合能力都得到一定程度的提高;经二步法改性处理后的气相生长碳纤维比未处理气相生长碳纤维对复合材料的力学性能的增强效果更为明显。     

石墨烯改性树脂基复合材料力学性能研究进展

树脂基复合材料具有比强度高、比模量大、耐高温、耐腐蚀、质轻等诸多优点,在航天军工、生物医疗、电子封装、体育器材等众多领域得到广泛应用。石墨烯作为一种典型的二维纳米材料,凭借其独特结构以及优异的物理化学性能而备受关注。近年来的研究表明石墨烯可以通过对增强纤维改性和对基体树脂改性的方法来提高树脂基复合材料的力学性能。本文介绍了石墨烯改性树脂基复合材料的增强增韧机理,对石墨烯改性纤维(碳纤维、玻璃纤维、芳纶纤维)增强复合材料以及树脂的改性方法进行了综述;着重阐述了石墨烯改性树脂基复合材料力学性能的研究进展,分析了石墨烯改性树脂基复合材料研究中依旧存在的两大问题,即石墨烯的分散性和界面结合问题,并对石墨烯改性树脂基复合材料的未来发展前景进行了展望。     

水润滑下稀土处理碳纤维填充聚四氟乙烯复合材料摩擦学性能

分别用氧化法、稀土处理法、氧化后稀土处理法对碳纤维进行表面处理，然后开展拉伸试验来对不同方法处理的碳纤维填充聚四氟乙烯复合材料进行界面粘着研究，并在UMT-2MT型摩擦磨损试验机上对水润滑条件下聚四氟乙烯复合材料摩擦学性能进行研究，使用扫描电镜对磨损表面进行观察，研究结果表明稀土处理方法在提高复合材料摩擦学性能上优于氧化方法，稀土处理碳纤维填充的聚四氟乙烯复合材料优良的摩擦学性能来自于碳纤雏增强体与聚四氟乙烯基体间强的界面粘着力。     

超高分子量聚乙烯纤维表面改性的研究进展

超高分子量聚乙烯(UHMWPE)纤维具有诸多优异性能,因此被广泛应用于纤维增强复合材料(FRP)。但是由于UHMWPE纤维表面光滑且无极性基团,与树脂基体粘接性差,可通过纤维表面改性有效提高FRP的界面强度,进而提升材料性能。本文总结了近几年基于化学处理、等离子体处理、电晕放电和辐射引发表面接枝等方法对UHMWPE纤维表面改性的研究进展,并对改性方法的发展进行了展望。     

苯并噁嗪改性液体成型环氧树脂的研究

采用具有低固化收缩特性的苯并噁嗪树脂(benzoxazine,BOZ)对液体成型环氧树脂进行改性,以期在不改变液体成型树脂耐热性、工艺性及力学性能的前提下,大幅度降低树脂的固化收缩率.对比研究了不同BOZ含量改性树脂的固化收缩特性、固化反应特性、液体成型工艺性及力学性能.并采用真空辅助树脂浸渗(vacuum assisted resin infusion,VARI)工艺制备了单向碳纤维织物增强复合材料,研究了复合材料的力学性能.结果表明,加入BOZ对液体成型树脂的反应性、工艺性及耐热性影响不大,改性树脂的固化收缩随BOZ含量的提高逐渐减小,其中BOZ质量分数为15 wt%的改性树脂,较未改性树脂的固化收缩减小约80%,拉伸强度提高约19%,冲击强度提高约148%.以此改性树脂作为基体的复合材料相对于未改性树脂复合材料的拉伸强度提高约23%,层间剪切强度提高约9%,具有良好的力学性能和界面结合性能.     

原位聚合法制备聚合物/纳米SiO_2复合材料的研究进展

纳米SiO_2改性聚合物制备的关键在于提高纳米粒子与聚合物基体的相容性及分散性;对纳米SiO_2进行不同的表面改性及选择合适的复合材料制备方法可以改变纳米粒子与聚合物基体的界面结合方式以及相容性和分散性,进而在不同程度上影响材料的性能.本文介绍了改性前后纳米SiO_2与聚合物基体的多种界面结合方式,对近年来利用原位聚合法制备聚合物/纳米SiO_2复合材料的研究现状和进展进行了综述.     

基于电泳沉积法碳纤维表面改性的研究进展及应用

近些年来,碳纤维(CF)由于具有优异的力学性能,被用作复合材料的增强体。但CF表面缺少极性基团,呈现化学惰性,使CF与树脂(EP)之间的界面粘结性能较差。为了改善该问题,需要对CF表面进行改性。氧化石墨烯(GO)和碳纳米管(CNT)具有大的比表面积,且表面含有大量的极性基团,将二者引入CF表面,可以有效改善CF与EP之间的界面问题。利用电泳沉积技术成功地制备了GO和CNT/EP复合材料,并显示出各种优异的界面性能。本文对国内外通过电泳沉积方法在CF表面沉积CNT和GO的改性以及电泳沉积GO和CNT的应用现状进行了综述和分析,并在此基础上,对电泳沉积碳纳米材料改性CF的研究趋势及前景进行展望。     

高亲水性环氧树脂的制备及对碳纤维的表面处理

在三乙胺催化下,以己二酸和环氧树脂制备了己二酸改性环氧树脂(AAEP),通过考察反应温度等因素对己二酸转化率和AAEP环氧值的影响,得到了AAEP合成的最佳条件.用傅里叶变换红外光谱和核磁共振对AAEP进行了表征.用KOH中和AAEP得到己二酸改性环氧树脂钾盐(AAEPK),测试了AAEPK乳液的性质和AAEPK处理后碳纤维的分散性,并通过场发射扫描电子显微镜和X射线光电子能谱对碳纤维的表面形貌和基团进行了研究.结果表明,AAEPK具有高亲水性,适用于碳纤维处理剂,当AAEPK的浓度和吸附量分别为1.0%(质量分数)和3.0 mg/g时,处理剂可在纤维表面均匀分布,使得碳纤维在树脂基体中的分散性得到改善.研究了处理剂对碳纤维/环氧树脂复合材料弯曲和剪切性能的影响,发现处理后碳纤维短丝/环氧树脂复合材料的弯曲强度和碳纤维布/环氧树脂复合材料的层间剪切强度较未处理的试样分别增加了168%和113%,说明AAEPK处理后碳纤维在基体中分散性和黏结性的提高是碳纤维/环氧树脂复合材料力学性能提高的主要原因.     

kevlar纤维增强尼龙6复合材料的力学性能

对Kevlar纤维进行了改性,使其成为己内酰胺阴离子开环聚合的活性中心,采用阴离子接枝法在Kevlar纤维(KF)表面接枝尼龙6低聚物,并与基体尼龙6混合,用挤出和注塑方式制备了尼龙6/改性Kevlar纤维(PA6/KF1)复合材料。ESEM和XPS分析表明,Kevlar纤维表面接枝上了尼龙6低聚物。比较了尼龙6/未改性Kevlar纤维(PA6/KF0)和PA6/KF1复合材料的力学性能及破坏形态,同时探讨了其破坏机理。结果表明,接枝尼龙6的KF1增强了KF与尼龙6复合材料界面的相互作用,拉伸强度、弯曲强度和弯曲模量分别提高了20.69%、12.26%和14.23%,但冲击强度降低了8.2%;当复合材料被破坏时,未改性纤维表面只粘附有少量的树脂尼龙6,而改性纤维的表面有较多的树脂包覆层,呈部分非界面脱粘破坏,具有良好的界面结合能力。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。