不同氮掺杂石墨烯氧还原反应活性的密度泛函理论研究

N掺杂石墨烯作为一种具有较高活性和稳定性的氧还原反应(ORR)催化剂,受到人们的广泛关注。然而不同的N掺杂类型对氧还原活性的影响一直存在争议。本文通过密度泛函理论分别对石墨型和吡啶型两种N掺杂石墨烯的ORR活性进行比较研究。能带结构分析表明,石墨氮掺杂石墨烯(GNG)的导电性随掺N量的增加而降低;吡啶氮掺杂石墨烯(PNG)的导电性则随掺N量的增加先提高后降低。当N掺杂浓度达到4.2%(原子分数)时,PNG具有最优导电性。且当N掺杂浓度大于1.4%时,PNG的导电率总是高于GNG。氧还原自由能阶梯曲线发现O₂的质子化是整个氧还原过程的潜在控制步骤。在同等氮掺杂浓度下,O₂的质子化自由能能变在GNG上低于在PNG上,意味着若在同等电子传输能力的情况下,GNG具有比PNG更优异的催化活性。进一步分析发现：当N掺杂浓度在低于2.8%时,GNG和PNG导电性差异小,其催化ORR活性由O₂质子化反应难易程度决定,GNG的催化活性优于PNG;当N掺杂浓度高于2.8%时,氮掺杂石墨烯的电子传输性能(导电性)成为决定催化剂ORR活性的主要因素,因此PNG表现出较GNG更高的活性。     

Electrochemical oxygen reduction on nitrogen doped graphene sheets in acid media

Nitrogen doped graphene were prepared via exfoliated graphite oxide. This graphene exhibited significantly high oxygen reduction activity. High electric conductivity, high surface area, large amount of edge sites and pyridinic N site in rGS (reduced graphene sheets) contribute to the high ORR (oxygen reduction reaction) activity. The rGS showed a potential to replace expensive Pt for oxygen reduction reaction in PEMFC.     

Fabrication of graphene-supported tetraferrocenylporphyrin electrocatalyst for oxygen reduction and its unique electrochemical response in both alkaline and acid media

A novel high-performance non-noble metal electrocatalyst for the oxygen reduction reaction (ORR) was fabricated by anchoring cobalt tetraferrocenylporphyrin (CoFcP) onto poly(sodium-p-styrenesulfonate) modified graphene (PSS-Gr) through solvothermally assisted π–π assembling method. The morphology of the assembled composite was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The interactions between CoFcP moieties and graphene sheets were confirmed by UV–Vis absorption spectroscopy and X-ray photoelectron spectroscopy. The electrocatalytic properties of the CoFcP/PSS-Gr catalyst towards the oxygen reduction reaction were assessed using rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) measurements in both alkaline and acidic media. In addition, cyclic voltammetry and chronoamperometric measurements were utilized to evaluate the catalytic activity and stability of the CoFcP/PSS-Gr composite in alkaline solution. The results showed that CoFcP supported on graphene exhibited an outstanding electrocatalytic performance towards the ORR comparable with commercial Pt/C catalyst in alkaline media, such as high onset potential (0.889 V vs. reversible hydrogen electrode, RHE), half wave potential (0.789 V vs. RHE), better tolerance to methanol, excellent stability (84.1 %, retention after 10000 s), and efficient four-electron pathway. Moreover, the proposed hybrid presented excellent catalytic activity in terms of onset potential (0.72 V vs. RHE) and high-electron transfer number compared with Pt/C in acidic media.     

FeNi Nanoparticles Coated on N-doped Ultrathin Graphene-like Nanosheets as Stable Bifunctional Catalyst for Zn-Air Batteries

High-performance and low-cost bifunctional catalysts are crucial to energy conversion and storage devices. Herein, a novel oxygen electrode catalyst with high oxygen evolution reaction and oxygen reduction reaction (OER/ORR) performance is reported based on bimetal FeNi nanoparticles anchored on N-doped graphene-like carbon (FeNi/N−C). The complete 2D ultrathin carbon nanosheet is induced by etching and stripping of molten sodium chloride and its ions in the carbonization process at suitable temperature. The obtained FeNi/N−C catalyst exhibits rapid reaction kinetics for OER, efficient four electron transfer for ORR, and outstanding bifunctional performance with reversible oxygen electrode index of 0.87 V for OER/ORR. Zn-air batteries with a high open-circuit voltage of 1.46 V and a stable discharge voltage of 1.23 V are assembled using liquid electrolytes, zinc sheet as Zn-electrode and FeNi/N−C coating on carbon cloth as air-electrode. The specific capacity is as high as 816 mAh g⁻¹ and there is extremely little decay after charge-discharge cycle time of 275 h for the FeNi/N−C as oxygen electrode catalyst in Zn-air battery, which are much better than that assembled with Pt/C−RuO₂ catalyst.     

Systematic Comparison of Graphene Materials for Supercapacitor Electrodes

A comparison of the performance of graphene-based supercapacitors is difficult, owing to the variety of production methods used to prepare the materials. To the best of our knowledge, there has been no systematic investigation into the effect of the graphene production method on the supercapacitor performance. In this work, we compare graphene produced through several routes. This includes anodic and cathodic electrochemically exfoliated graphene, liquid phase exfoliated graphene, graphene oxide, reduced graphene oxide, and graphene nanoribbons. Graphene oxide exhibited the highest capacitance of approximately 154 F g⁻¹ in 6 M KOH at 0.5 A g⁻¹ attributed to oxygen functional groups giving an additional pseudocapacitance and preventing significant restacking; however, the capacitance retention was poor, owing to the low conductivity. In comparison, the anodic electrochemically exfoliated graphene exhibited a capacitance of approximately 44 F g⁻¹, the highest of the ‘pure’ graphene materials, which all exhibited superior capacitance retention, owing to their higher conductivity. The cyclability of all of the materials, with the exception of reduced graphene oxide (70 %), was found to be greater than 95 % after 10 000 cycles. These results highlight the importance of matching the graphene production method with a specific application; for example, graphene oxide and anodic electrochemically exfoliated graphene would be best suited for high energy and power applications, respectively.     

Electrochemical and oxygen reduction properties of pristine and nitrogen-doped few layered graphene nanoflakes (FLGs)

Vertically aligned few layered graphene (FLGs) nanoflakes were synthesized by microwave plasma deposition for various time durations ranging from 30 to 600 s to yield graphene films of varying morphology, microstructure and areal/edge density. Their intrinsic electrochemical properties were explored using Fe(CN)₆ ^3?/4? and Ru(NH₃)₆ ^3+/2+ redox species. All the FLG electrodes demonstrate fast electron transfer kinetics with near ideal ΔEp values of 60–65 mV. Using a relationship between electron transfer rate and edge plane density, an estimation of the edge plane density was carried out which revealed a moderation of edge plane density with increase in growth time. The pristine FLGs also possess excellent electrocatalytic activity towards oxygen reduction reaction (ORR) in alkaline solutions. This ORR activity can be further enhanced by exposing the pristine FLGs to nitrogen electron cyclotron resonance plasma. The metal free N-doped FLGs exhibit much higher electrocatalytic activity towards ORR than pristine FLGs with higher durability and selectivity than Pt-based catalysts. The excellent electrochemical performance of N-doped FLGs is explained in terms of enhanced edge plane exposure, high content of pyridinic nitrogen and an increase in the electronic density of states.     

Nitrogen-doped ordered porous carbon catalyst for oxygen reduction reaction in proton exchange membrane fuel cells

Three different N-doped ordered porous carbons (CNx) were produced by a nanocasting process using polyaniline as the carbon and nitrogen precursor. A pyrolysis treatment of iron chloride-impregnated CNx under nitrogen is used in the preparation of the carbon composite catalysts, and this is followed by posttreatments and optimization of the iron loading and the pore size. Exploration of the catalytic activity of the CNx products for catalyzing the oxygen reduction reaction (ORR) using rotating disk electrode measurements and single-cell tests shows that the onset potential for ORR of the most effective catalyst in 0.5 M H₂SO₄ is as high as 0.9 V vs. the normal hydrogen electrode. A proton exchange membrane fuel cell constructed with the catalyst exhibits a current density as high as 0.52 A cm^?2 at 0.6 V with 2 atm back pressure using a cathode catalyst loading of 6 mg cm^?2. The average pore diameters of synthesized CNx-12, CNx-15, and CNx-16 are 0.7, 4.3, and 14 nm, respectively. It is observed that the pore size and specific surface area are an important factor for increased catalyst activity. The pore size of the most effective catalysts is found to be 4.3 nm.     

Mesoporous carbon nitride loaded with Pt nanoparticles as a bifunctional air electrode for rechargeable lithium-air battery

A composite comprised of oxygen reduction reaction (ORR) catalyst and oxygen evolution reaction (OER) catalyst was designed and applied as a bifunctional electrocatalyst for the air electrode of the lithium-air battery. The ordered mesoporous carbon nitride (MCN) prepared by a nano hard-templating approach displayed a surface area as high as 648 m² g^?1 and a large pore volume of 0.7 cm³ g^?1 and acted as both the ORR catalyst and the support for the in situ-formed OER catalyst of Pt particles with a diameter of 3–4 nm. The electrochemical performances of the electrode were examined in a solid-state lithium-air cell structured as Li/LATP-based electrolyte/cathode, which demonstrated a higher round-trip efficiency and lower overpotential compared with the Pt@AB and MCN electrodes. The combination of the OER and ORR catalysts is proved as an effective way to improve the performance of lithium-air batteries.     

3D nitrogen-doped graphene aerogel-supported Fe3O4 nanoparticles as efficient electrocatalysts for the oxygen reduction reaction

Three-dimensional (3D) N-doped graphene aerogel (N-GA)-supported Fe(3)O(4) nanoparticles (Fe(3)O(4)/N-GAs) as efficient cathode catalysts for the oxygen reduction reaction (ORR) are reported. The graphene hybrids exhibit an interconnected macroporous framework of graphene sheets with uniform dispersion of Fe(3)O(4) nanoparticles (NPs). In studying the effects of the carbon support on the Fe(3)O(4) NPs for the ORR, we found that Fe(3)O(4)/N-GAs show a more positive onset potential, higher cathodic density, lower H(2)O(2) yield, and higher electron transfer number for the ORR in alkaline media than Fe(3)O(4) NPs supported on N-doped carbon black or N-doped graphene sheets, highlighting the importance of the 3D macropores and high specific surface area of the GA support for improving the ORR performance. Furthermore, Fe(3)O(4)/N-GAs show better durability than the commercial Pt/C catalyst.     

Doping effect of boron and phosphorus on nitrogen-based mesoporous carbons as electrocatalysts for oxygen reduction reaction in acid media

Doped mesoporous carbons comprising nitrogen, boron, and phosphorus (N, B, and P, respectively) were prepared as non-Pt catalysts for oxygen reduction reaction (ORR) in an acidic solution. The N-doped carbons were varied to increase their catalytic activity through by additionally doping of B and P. All the mesoporous carbons were synthesized by carbonizing polyaniline at 900 °C for the N species, while the B and P species were inserted into the carbon structure at the carbon growth step. The linear sweep voltammogram recorded in the acidic solution showed that the ORR activity of the N-doped carbon catalysts increased significantly after the addition of B. An approximately 19 % increase in the pyridinic N content at the carbon surface was observed, along with B-N-C moieties with a binding energy of 399.5 eV. The non-precious metal ORR catalysts were prepared via pyrolysis, with the insertion of an additional transition metal (iron, Fe). The deconvoluted X-ray photoelectron spectroscopy (XPS) results showed that the Fe-N peak was generated after the pyrolysis. The peak intensity of the quaternary N also increased compared with the pyridic and pyrrolic N, which indicates that Fe serves to catalyze the modification of N species. The numerical examinations showed that N- and B-doped mesoporous carbon (NBC) 1.5 % Fe had the highest limited current (4.94 mA/cm²), with the B-doped carbon still the most active mesoporous carbon catalyst for ORR. As a result, it can be said that Fe positively contributes to the formation of graphitic N, which is known to be an active site for ORR. The cyclic voltammetry results showed that the peak area of the NBC 1.5 % Fe catalyst was larger than that of the N-doped mesoporous carbon (NC) 1.5 % Fe catalyst. It was concluded that B doping enhances the ORR activity and the stability of carbon materials even after 1000 cycles under acidic conditions.     

The reduction of graphene oxide by elemental copper and its application in the fabrication of graphene supercapacitor

In this work, graphene oxide (GO) was directly reduced by copper to reduced graphene oxide (RGO) and formed a highly uniform RGO film on copper foil or copper-modified titanium (Ti) substrate. The characterization of as-prepared RGO film by FTIR and XRD indicated that GO was partially reduced by copper while some oxygen-containing groups still remained. The conductivity of the RGO film was improved from 3.76?×?10³ to 2.98?×?10⁴ S/m after it was further electrochemically reduced due to the removal of additional oxygen groups. The graphene supercapacitor prepared with this method exhibited better performances in a neutral aqueous electrolyte compared with that reported for graphene electrodes prepared by other fabrication methods.     

Synthesis of <Emphasis Type="Italic">N</Emphasis>-hydroxy-imidamide-functionalized graphene: an efficient metal-free electrocatalyst for oxygen reduction

Metal-free electrocatalysts for oxygen reduction reaction (ORR) are key to the development of efficient, durable, and low-cost alternatives to noble-metal-based electrocatalysts in fuel cell cathodes. In recent years, many efforts are directed to the metal-free catalyst based on heteroatom-doped graphene. In this work, we demonstrate that the graphene surface can be converted into the catalyst for the oxygen reduction by chemical functionalization. In this context, we first synthesized malononitrile-functionalized graphene oxide. Amidoximation of nitrile group and reduction in graphene oxide were then carried out by hydroxylamine in one step. The electrochemical behavior of functionalized graphene-modified electrode for the reduction in oxygen was studied. The results showed that the electrocatalyst fabricated by this method exhibited striking catalytic activities in alkaline solution. In alkaline solution, this catalyst showed a competitive activity to the commercial Pt catalyst via four-electron transfer pathway with better ORR selectivity and stability. In addition, this metal-free electrocatalyst exhibited tolerance to methanol crossover effect. Based on its outstanding performance, this functionalized graphene electrocatalyst showed the promising prospect of a metal-free catalyst for fuel cell with much lower cost than currently used Pt/C catalyst.     

A facile nitrogen-doped carbon encapsulation of CoFe2O4 nanocrystalline for enhanced performance of lithium ion battery anodes

Nitrogen-doped (N-doped) carbon encapsulation of CoFe₂O₄ nanocrystalline is achieved by a simple pressure-assisted pyrrole pyrolysis method. The CoFe₂O₄/N-doped carbon nanocomposite (CFO/NC) delivers a capacity of 646.2 mAh g^–1 after 80 cycles at 0.1 C, exhibits stable cycling performance at various rates from 0.2 to 1.6 C and retains a capacity of 662.8 mAh g^–1 as the rate returns back to 0.1 C, showing significantly improved lithium storage reversibility compared to the bare CFO. A different lithiation mechanism of CFO/NC above and below the plateau relative to CFO in the first discharge is analyzed in detail based on the potential profiles and cyclic voltammogram curves. Morphology characterization of the cycled electrodes confirms much better integrity of CFO/NC electrode due to the buffer effect of N-doped carbon coating. Electronic conductivity and electrochemical impedance spectroscopy measurements indicate enhanced electrode reaction kinetics of CFO/NC. All the results contribute to its improved electrochemical performance.     

Characterization of Fe/N-doped graphene as air-cathode catalyst in microbial fuel cells

This work proposed a simple and efficient approach for synthesis of durable and efficient non-precious metal oxygen reduction reaction(ORR) electro-catalysts in MFCs. The rod-like carbon nanotubes(CNTs)were formed on the Fe–N/SLG sheets after a carbonization process. The maximum power density of1210 ± 23 m W·m~(-2) obtained with Fe–N/SLG catalyst in an MFC was 10.7% higher than that of Pt/C catalyst(1080 ± 20 mW ·m~(-2)) under the same condition. The results of RDE test show that the ORR electron transfer number of Fe–N/SLG was 3.91 ± 0.02, which suggested that ORR catalysis proceeds through a four-electron pathway. The whole time of the synthesis of electro-catalysts is about 10 h, making the research take a solid step in the MFC expansion due to its low-cost, high efficiency and favorable electrochemical performance. Besides, we compared the electrochemical properties of catalysts using SLG, high conductivity graphene(HCG, a kind of multilayer graphene) and high activity graphene(HAG, a kind of GO) under the same conditions, providing a solution for optimal selection of cathode catalyst in MFCs.The morphology, crystalline structure, elemental composition and ORR activity of these three kinds of Fe–N/C catalysts were characterized. Their ORR activities were compared with commercial Pt/C catalyst.It demonstrates that this kind of Fe–N/SLG can be a type of promising highly efficient catalyst and could enhance ORR performance of MFCs.     

Alkaline oxygen evolution: exploring synergy between fcc and hcp cobalt nanoparticles entrapped in N-doped graphene

Herein, we report a Mott-Schottky catalyst by entrapping cobalt nanoparticles inside the N-doped graphene shell (Co@NC). The Co@NC delivered excellent oxygen evolution activity with an overpotential of merely 248 mV at a current density of 10 mA cm^–2 with promising long-term stability. The importance of Co encapsulated in NC has further been demonstrated by synthesizing Co nanoparticles without NC shell. The synergy between the hexagonal close-packed (hcp) and face-centered cubic (fcc) Co plays a major role to improve the OER activity, whereas the NC shell optimizes the electronic structure, improves the electron conductivity, and offers a large number of active sites in Co@NC. The density functional theory calculations have revealed that the hcp Co has a dominant role in the surface reaction of electrocatalytic oxygen evolution, whereas the fcc phase induces the built-in electric field at the interfaces with N-doped graphene to accelerate the H⁺ ion transport.     

Determination of Sudan I Using Electrochemically Reduced Graphene Oxide

Electrochemically reduced graphene oxide (ER-GO) was prepared by reducing exfoliated graphene oxide sheets on a glassy carbon electrode (GCE). The voltammetric responses of Sudan I-IV were studied at the ER-GO modified GCE (ER-GO/GCE). Compared with chemically reduced graphene oxide (CR-GO) modified electrode (CR-GO/GCE), ER-GO/GCE showed higher voltammetric responses to Sudan I. The electrode had a linear response to Sudan I in the range of 0.04–8.0 µmol L^?1 and a detection limit of 0.01 µmol L^?1. The real sample determination indicated that the proposed method was reliable, effective, and sufficient.     

3D Nitrogen-Doped Graphene Encapsulated Metallic Nickel–Iron Alloy Nanoparticles for Efficient Bifunctional Oxygen Electrocatalysis

It is extremely desirable to explore high-efficient, affordable and robust oxygen electrocatalysts toward rechargeable Zn–air batteries (ZABs). A 3D porous nitrogen-doped graphene encapsulated metallic Ni₃Fe alloy nanoparticles aerogel (Ni₃Fe-GA₁) was constructed through a facile hydrothermal assembly and calcination process. Benefiting from 3D porous configuration with great accessibility, high electrical conductivity, abundant active sites, optimal nitrogen content and strong electronic interactions at the Ni₃Fe/N-doped graphene heterointerface, the obtained aerogel showed outstanding catalytic performance toward the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). Specifically, it exhibited an overpotential of 239 mV to attain 10 mA cm⁻² for OER, simultaneously providing a positive onset potential of 0.93 V within a half-wave potential of 0.8 V for ORR. Accordingly, when employed in the aqueous ZABs, Ni₃Fe-GA₁ achieved higher power density and superior reversibility than Pt/C−IrO₂ catalyst, making it a potential candidate for rechargeable ZABs.     

The MOF/GO-based derivatives with Co@CoO core-shell structure supported on the N-doped graphene as electrocatalyst for oxygen reduction reaction

The development of nonprecious catalyst for oxygen reduction reaction (ORR) is important for the commercialization of the alkaline fuel cells (AFCs). Herein, we prepared a kind of Co-based nanoparticles (NPs) with a core-shell (Co@CoO) structure supported on the N-doped graphene (Co@CoO/NG) as an efficient ORR catalyst via simply pyrolyzing the ZIF-67 anchored on the synthesized graphene oxide (GO). The catalytic activity for ORR of the obtained Co@CoO/NG is comparable with the state-of-art Pt/C catalyst in terms of the onset and half-wave potential in the alkaline solution. In addition, the Co@CoO/NG exhibited an excellent ORR durability and antimethanol activity compared to the commercial Pt/C. This research would provide a simple strategy to prepare the high-performance nonprecious metal-based catalysts for AFCs.     

Multifunctional Co3S4/Graphene Composites for Lithium Ion Batteries and Oxygen Reduction Reaction

Cobalt sulfide is a good candidate for both lithium ion batteries (LIBs) and cathodic oxygen reduction reaction (ORR), but low conductivity, poor cyclability, capacity fading, and structural changes hinder its applications. The incorporation of graphene into Co₃S₄ makes it a promising electrode by providing better electrochemical coupling, enhanced conductivity, fast mobility of ions and electrons, and a stabilized structure due to its elastic nature. With the objective of achieving high‐performance composites, herein we report a facile hydrothermal process for growing Co₃S₄ nanotubes (NTs) on graphene (G) sheets. Electrochemical impedance spectroscopy (EIS) verified that graphene dramatically increases the conductivity of the composites to almost twice that of pristine Co₃S₄. Electrochemical measurements indicated that the as‐synthesized Co₃S₄/G composites exhibit good cyclic stability and a high discharge capacity of 720 mA h g^?1 up to 100 cycles with 99.9 % coulombic efficiency. Furthermore, the composites react with dissolved oxygen in the ORR by four‐ and two‐electron mechanisms in both acidic and basic media with an onset potential close to that of commercial Pt/C. The stability of the composites is much higher than that of Pt/C, and exhibit high methanol tolerance. Thus, these properties endorse Co₃S₄/G composites as auspicious candidates for both LIBs and ORR.     

Facile one-step electrochemical fabrication of a non-enzymatic glucose-selective glassy carbon electrode modified with copper nanoparticles and graphene

We have developed a non-enzymatic glucose sensor by using a composite prepared from copper nanoparticles (CuNPs) and graphene which can be prepared by simple 1-step electrochemical reduction using graphene oxide (GO) and copper ion as the starting materials. The GO is electrochemically reduced to graphene at a voltage of ?1.5 V, and this is accompanied by the simultaneous formation of CuNPs on the surface of the graphene. This novel nanocomposite combines the advantages of graphene and of CuNPs and displays good electrocatalytic activity toward glucose in alkaline media. The performance of the respective glucose electrode was evaluated by amperometric experiments and revealed a fast response (<2 s), a low detection limit (200 nM), and high sensitivity (607 μA mM^?1). The sensor also exhibits good reproducibility and very good specificity for glucose over ascorbic acid, dopamine, uric acid, fructose, lactose and sucrose.