Self-assembly of vertically aligned gold nanorod arrays on patterned substrates

Nanorods standing at attention! A self-assembly technique based on convective and capillary forces was used for the direct fabrication of standing arrays of gold nanorods on lithographically predefined areas. The hexagonal close-packed structure of gold nanorods creates an ideal substrate for surface-enhanced Raman spectroscopy.     

Kinetic stages of single-component colloidal crystallization

To harness the full potential of colloidal self-assembly, the dynamics of the transition between colloids in suspension to a colloidal crystalline film should be better understood. In this report, the structural changes during the self-assembly process in a vertical configuration for colloids in the size range 200-400 nm are monitored in situ, using the transmission spectrum of the colloidal assembly treated as an emergent photonic crystal. It is found that there are several sequential stages of colloidal ordering: in suspension, with a larger lattice parameter than the solid state, in a close-packed wet state with solvent in the interstices, and, finally, in a close-packed dry state with air in the interstices. Assuming that these stages lead continuously from one to another, we can interpret colloidal crystallization as being initiated by interparticle forces in suspension first, followed by capillary forces. This result has implications for identifying the optimum conditions to obtain high-quality nanostructures of submicrometer-sized colloidal particles.     

Dewetting dynamics in miscible polymer-polymer thin film mixtures

Thin polystyrene films supported by oxidized silicon (SiOx/Si) substrates may be unstable or metastable, depending on the film thickness, h, and can ultimately dewet the substrate when heated above their glass transition. In the metastable regime, holes nucleate throughout the film and subsequently grow due to capillary driving forces. Recent studies have shown that the addition of a second component, such as a copolymer or miscible polymer, can suppress the dewetting process and stabilize the film. We examined the hole growth dynamics and the hole morphology in thin film mixtures composed of polystyrene and tetramethyl bisphenol-A polycarbonate (TMPC) supported by SiOx/Si substrates. The hole growth velocity decreased with increasing TMPC content beyond that expected from changes in the bulk viscosity. The authors show that the suppression of the dewetting velocity is primarily due to reductions in the capillary driving force for dewetting and to increased friction at the substrate-polymer interface. The viscosity, as determined from the hole growth dynamics, decreases with decreasing film thickness, and is connected to a depression of the glass transition of the film.     

SiOx纳米管的制备及其发光特性

Amorphous SiOx nanotubes with homogeneous diameters were fabricated in large-scale on silicon substrate by thermal evaporation method, with liquid gallium as medium. The average diameter of tubes is about 80 nm and the length is more than 10 1m, with small ratio between the inner and outer diameter of the tube. The silicon element in the substrate and the residual oxygen element in reaction chamber were first dissolved into liquid Ga. Then the SiOx precipitated from the surface of gallium droplet, forming the nanotube structure with Ga droplet being the center. The room temperature photoluminescence measurements under excitation at 260 nm show that the SiOx nanotubes has a strong blue emission at 453 nm with two shoulders at 410 and 480 nm respectively, which may be related to oxygen defects. The preparation method improved the traditional complicated method and also provided a new way to fabricate SiOx nanotubes in large quantity.     

Stability of the gold/silica thin film interface: electrochemical and surface plasmon resonance studies

This article reports chemical stability studies of a gold film electrode coated with thin silicon oxide (SiOx) layers using electrochemical, surface plasmon resonance (SPR) and atomic force microscopy (AFM) techniques. Silica films with different thicknesses (d = 6.4, 9.7, 14.5, and 18.5 nm) were deposited using a plasma-enhanced chemical vapor deposition technique (PECVD). For SiOx films with d >/= 18.5 nm, the electrochemical behavior is characteristic of a highly efficient barrier for a redox probe. SiOx films with thicknesses between 9.5 and 14.5 nm were found to be less efficient barriers for electron transfer. The Au/SiOx interface with 6.4 nm of SiOx, however, showed an enhanced steady-state current compared to that of the other films. The stability of this interface in solutions of different pH was investigated. Whereas a strongly basic solution led to a continuous dissolution of the SiOx interface, acidic treatment produced a more reticulated SiOx film and improved electrochemical behavior. The electrochemical results were corroborated by SPR measurements in real time and AFM studies.     

Field-induced adsorption exclusion of particles from one-dimensional nanomagnets

I study the adsorption of paramagnetic colloids to one-dimensional nanomagnets. It is found that in the absence of external magnetic fields the colloids tend to adsorb to the nanomagnet by arranging themselves in a nearly close-packed formation, whereas in an external field some of the colloids are repelled due to dipolar interactions. I develop a theory for this phenomenon and show that it is in agreement with experimental data.     

Growth and reactions of SiOx/Si nanostructures on surface-templated molecule corrals

Surface-templated nanostructures on the highly oriented pyrolytic graphite (HOPG) basal plane were created by controlled Cs+- or Ga+)ion bombardment, followed by subsequent oxidation at high temperature, forming molecule corrals. The corrals were then used for template growth of SiOx/Si nanostructures. We demonstrate here that, for SiOx/Si nanostructures formed in controlled molecule corrals, the amount of silicon deposited on the surface is directly correlated with the corral density, making it possible to generate patterned SiOx/Si nanostructures on HOPG. Since the size, depth, position, and surface density of the nanostructures can be controlled on the HOPG, it is possible to produce surfaces with patterned or gradient functionalities for applications in fields such as biosensors, microelectronics, and biomaterials (e.g., neuron pathfinding). If desired, the SiOx structures can be reduced in size by etching in dilute HF, and further oxidation of the nanostructures is slow enough to provide plenty of time to functionalize them using ambient and solution reactions and to perform surface analysis. Organosilane monolayers on surface-templated SiOx/Si nanostructures were examined by X-ray photoelectron spectroscopy, time-of-flight secondary ion mas spectrometry, and atomic force microscopy. Silanes with long alkyl chains such as n-octadecyltrichlorosilane (C18) were found to both react on SiOx/Si nanostructures and to condense on the HOPG basal plane. Shorter-chain silanes, such as 11-bromoundicyltrimethoxysilane (C11) and 3-mercaptopropyltrimethoxysilane (C3) were found to react preferentially with SiOx/Si nanostructures, not HOPG. The SiOx/Si nanostructures were also found to be stable toward multiple chemical reactions. Selective modification of SiOx/Si nanostructures on the HOPG basal plane is thus achievable.     

Colloidal crystal layers of hexagonal nanoplates by convective assembly

Particles of the zeolite ZSM-2 prepared as nearly hexagonal nanoplatelets were coated onto flat substrates by a convective assembly technique. On the submillimeter scale, coatings ranged in patterns from striped to continuous. Particles were preferentially oriented out-of-plane, as supported by X-ray diffractometry. The novel observation is that where the particle coating was only a monolayer thick, particles were locally close-packed and uniformly oriented both in and out of plane in a hexagonal colloidal crystalline arrangement that may be described as being tiled (observations by scanning electron microscopy). This is the first documented demonstration of convective assembly applied to anisometric nanoparticles that resulted in particulate coatings with locally ordered microstructure, i.e., colloidal crystallinity.     

基于表面起皱法的梯度图案的可控制备

报道了基于非刻蚀法的表面起皱机制来实现高分子薄膜表面的周期性梯度图案的简单可控制备.即对于处于机械拉伸状态的聚二甲基硅氧烷(PDMS)弹性基底,在其底部垫入"积木",而后对其进行紫外-臭氧(UVO)和氧等离子体(OP)的联合表面处理."积木"的加入引起了表面处理后表面硅氧层(SiOx)梯度厚度的形成,进而当释放拉伸应变后,诱导产生了梯度皱纹图案.结果表明:当UVO与OP联用处理时,不仅实现了较小拉伸应变下梯度皱纹形貌的制备,而且扩大了UVO单独使用时梯度皱纹周期的变化范围.通过OP与UVO的处理顺序和处理时间等因素的简单调节,进一步实现了不同梯度皱纹微结构的精细构筑.     

Preparation of ZnO colloids by aggregation of the nanocrystal subunits

Colloidal ZnO particles with narrow size distribution were prepared via a sol-gel process by base-catalyzed hydrolysis of zinc acetate. The morphology of ordered arrays of the particles was recorded by SEM. SEM also reveals that these uniform particles were composed of tiny ZnO subunits (singlets) sized of several nanometers. The size of the singlets, which is confirmed by X-ray diffraction and UV-vis absorption spectra, increases as the aging time is prolonged. The size-selective formation of colloids by aggregation of nanosized subunits is proposed to consist of two-stage growth by nucleation of nanosized crystalline primary particles and their subsequent aggregation into polycrystalline secondary colloids. The aggregates are all spherical because the internal rearrangement processes are fast enough. The ZnO colloids, i.e., the aggregates, tend to self-assemble into well-ordered hexagonal close-packed structures. Room-temperature photoluminescence was characterized for green and aged ZnO.     

Colloidal assembly: the road from particles to colloidal molecules and crystals

Colloidal particles may be considered as building blocks for materials, just like atoms are the bricks of molecules, macromolecules, and crystals. Periodic arrays of colloids (colloidal crystals) have attracted much interest over the last two decades, largely because of their unique photonic properties. The archetype opal structures are based on close-packed arrays of spheres of submicrometer diameter. Interest in structuring materials at this length scale, but with more complex features and ideally by self-assembly processes, has led to much progress in controlling features of both building blocks and assemblies. The necessary ingredients include colloids, colloidal clusters, and colloidal "molecules" which have special shapes and the ability to bind directionally, the control over short-range and long-range interactions, and the capability to place and orientate these bricks. This Review highlights recent experimental and theoretical progress in the assembly of colloids larger than 50 nm.     

Non-Lithography Hydrodynamic Printing of Micro/Nanostructures on Curved Surfaces

A key issue of micro/nano devices is how to integrate micro/nanostructures with specified chemical components onto various curved surfaces. Hydrodynamic printing of micro/nanostructures on three-dimensional curved surfaces is achieved with a strategy that combines template-induced hydrodynamic printing and self-assembly of nanoparticles (NPs). Non-lithography flexible wall-shaped templates are replicated with microscale features by dicing a trench-shaped silicon wafer. Arising from the capillary pumped function between the template and curved substrates, NPs in the colloidal suspension self-assemble into close-packed micro/nanostructures without a gravity effect. Theoretical analysis with the lattice Boltzmann model reveals the fundamental principles of the hydrodynamic assembly process. Spiral linear structures achieved by two kinds of fluorescent NPs show non-interfering photoluminescence properties, while the waveguide and photoluminescence are confirmed in 3D curved space. The printed multiconstituent micro/nanostructures with single-NP resolution may serve as a general platform for optoelectronics beyond flat surfaces.     

Dip-pen patterning and surface assembly of peptide amphiphiles

This paper presents results on controlling the surface morphology of evaporation-driven self-assembly of peptide amphiphile (PA) nanofibers by dip-pen nanolithography. These PA nanofibers, which measure only a few nanometers in diameter, can be oriented perpendicularly to the receding edge of a solution. Dragging a meniscus of PA ink with an atomic force microscope (AFM) tip creates reproducibly aligned arrays of isolated and close-packed PA nanofiber patterns on silicon substrates, utilizing surface coating of poly(ethylene glycol) to suppress the self-assembly of nanofibers on AFM tips. We also demonstrate the ability to construct double-layer patterns of differing nanofiber orientations at the same position. This result could be important in producing a complex, multilayer pattern of these peptide-based supramolecular nanostructures.     

Nanometer-scale wetting of the silicon surface by its equilibrium oxide

Despite the extremely broad technical applications of the Si/SiO2 structure, the equilibrium wetting properties of silicon oxide on silicon are poorly understood. Here, we produce new results in which a solid-state buffer method is used to systematically titrate oxygen activity about the Si/SiO2 coexistence value. The equilibrium morphology at the Si(001) surface over >8 decades of PO2 about coexistence is revealed to be a uniform sub-stoichiometric SiOx film of sub-nanometer thickness, coexisting with secondary island structures which coarsen with annealing time. A new thermodynamic method using chemical potential to stabilize and control surficial oxides in nanoscale devices is suggested.     

Controlled nanoparticle assembly by dewetting of charged polymer solutions

In this paper, we present an alternative approach for controlled nanoparticle organization on a solid substrate by applying dewetting patterns of charged polymer solutions as a templating system. Thin films of charged polymer solutions dewet a solid substrate to form complex dewetting patterns that depend on the polymer charge density. These patterns, ranging from polygonal networks to elongated structures that are stabilized by viscous forces during dewetting, serve as potential templates for two-dimensional nanoparticle organization on a solid substrate. Thus, while nanoparticles dried in pure water undergo self-assembly to form close-packed arrays, addition of charged polymer in the dispersion leads to the formation of open structures that are directed by the dewetting patterns of the polymer solution. In this study, we focus on the application of elongated structures resulting from dewetting of high-charge-density polymer solutions to align nanoparticles of silica and gold into long chains that are several micrometers in length. The particle ordering process is a two-step mechanism: an initial confinement of the nanoparticles in the dewetting structures and self-assembly of the particles within these structures upon further drying by lateral capillary attractions.     

A universal approach to fabricate ordered colloidal crystals arrays based on electrostatic self-assembly

We present a novel and simple method to fabricate two-dimensional (2D) poly(styrene sulfate) (PSS, negatively charged) colloidal crystals on a positively charged substrate. Our strategy contains two separate steps: one is the three-dimensional (3D) assembly of PSS particles in ethanol, and the other is electrostatic adsorption in water. First, 3D assembly in ethanol phase eliminates electrostatic attractions between colloids and the substrate. As a result, high-quality colloidal crystals are easily generated, for electrostatic attractions are unfavorable for the movement of colloidal particles during convective self-assembly. Subsequently, top layers of colloidal spheres are washed away in the water phase, whereas well-packed PSS colloids that are in contact with the substrate are tightly linked due to electrostatic interactions, resulting in the formation of ordered arrays of 2D colloidal spheres. Cycling these processes leads to the layer-by-layer assembly of 3D colloidal crystals with controllable layers. In addition, this strategy can be extended to the fabrication of patterned 2D colloidal crystals on patterned polyelectrolyte surfaces, not only on planar substrates but also on nonplanar substrates. This straightforward method may open up new possibilities for practical use of colloidal crystals of excellent quality, various patterns, and controllable fashions.     

Formation of spatially patterned colloidal photonic crystals through the control of capillary forces and template recognition

We report the formation of microscopic patterns of substrate-supported, 3D planar colloidal crystals using physical confinement in conjunction with surfaces displaying predetermined binary patterns of hydropholicity. The formation process involves a primary self-assembly wherein nano- and microscale colloids order into a photonic fcc lattice via capillary interactions followed by a secondary template-induced crystal cleavage step. Following this method, arbitrary arrays of pattern elements, which preserve structural and orientational properties of the parent crystal, can be easily obtained.     

Effect of intermittent convection movements on voltammogram and current transients

The influence of intermittent convection movements on electrochemical voltammograms is investigated. When the bath temperature rises to 315 K, the voltammograms exhibit irregular plateaus that differ for independent voltammetry scans, even when the setup is maintained under exactly the same conditions. In this paper, we show that such behavior can be caused by convection movements that develop in the electrolytic cell as a consequence of velocity fluctuations, since no bubbles or regular convective patterns are observed at this temperature. Theoretical current-potential curves for the heterogeneous deposition of metals on silicon electrodes is derived from a model consisting of a one-dimensional balance equation that includes diffusion, convection, and reaction through a time-dependent boundary condition. We obtain the current density associated with the adsorption of particles on the surface and, through this expression, we consider the effect of constant convective velocities on voltammograms. Finally, we examine the effect of random convective movements, described by a Monte Carlo algorithm that takes into account the random temporal fluctuations around a null convective current. The model predicts accentuated fluctuations on the current profiles, especially on the current plateaus that correspond to a stationary current regime. The validity of the theoretical model is checked against experimental data.     

Surface-enhanced Raman spectroscopy based on conical holed enhancing substrates

In this contribution, surface-enhanced Raman spectroscopy (SERS) based on conical holed glass substrates deposited with silver colloids was reported for the first time. It combines the advantages of both dry SERS assays based on plane films deposited with silver colloids and wet SERS assays utilizing cuvettes or capillary tubes. Compared with plane glass substrates deposited with silver colloids, the conical holed glass substrates deposited with silver colloids exhibited five-to ten-folds of increase in the rate of signal enhancement, due to the internal multiple reflections of both the excitation laser beam and the Raman scattering photons within conical holes. The application of conical holed glass substrates could also yield significantly stronger and more reproducible SERS signals than SERS assays utilizing capillary tubes to sample the mixture of silver colloids and the solution of the analyte of interest. The conical holed glass substrates in combination with the multiplicative effects model for surface-enhanced Raman spectroscopy (MEM_SERS) achieved quite sensitive and precise quantification of 6-mercaptopurine in complex plasma samples with an average relative prediction error of about 4% and a limit of detection of about 0.02 μM using a portable i-Raman 785H spectrometer. It is reasonable to expect that SERS technique based on conical holed enhancing substrates in combination with MEM_SERS model can be developed and extended to other application areas such as drug detection, environmental monitoring, and clinic analysis, etc.     

Colloidal rings in a liquid mixture

We investigate the self-assembly of colloidal particles on microscopic decane droplets in water and show that, by use of paramagnetic colloids, it is possible to assemble ringlike structures that can be controlled with a magnetic field. Moreover, the use of paramagnetic colloids allows us to determine the attractive forces between the colloids located at the three-phase contact line between decane, water, and air. The attractive force is in the femtonewton range and is attributed to capillary interactions due to interface deformations. When the liquid emulsion dries on a glass slide, we observe solid deposits in the form of microscopic rings of varying diameters.