Effect of sintering on the ionic conductivity of garnet-related structure Li5La3Nb2O12 and In- and K-doped Li5La3Nb2O12

Garnet-structure related metal oxides with the nominal chemical composition of Li₅La₃Nb₂O₁₂, In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ and K-substituted Li_5.5La_2.75K_0.25Nb₂O₁₂ were prepared by solid-state reactions at 900, 950, and 1000 °C using appropriate amounts of corresponding metal oxides, nitrates and carbonates. The powder XRD data reveal that the In- and K-doped compounds are isostructural with the parent compound Li₅La₃Nb₂O₁₂. The variation in the cubic lattice parameter was found to change with the size of the dopant ions, for example, substitution of larger In³⁺(r_CN6: 0.79 Å) for smaller Nb⁵⁺ (r_CN6: 0.64 Å) shows an increase in the lattice parameter from 12.8005(9) to 12.826(1) Å at 1000 °C. Samples prepared at higher temperatures (950, 1000 °C) show mainly bulk lithium ion conductivity in contrast to those synthesized at lower temperatures (900 °C). The activation energies for the ionic conductivities are comparable for all samples. Partial substitution of K⁺ for La³⁺ and In³⁺ for Nb⁵⁺ in Li₅La₃Nb₂O₁₂ exhibits slightly higher ionic conductivity than that of the parent compound over the investigated temperature regime 25-300 °C. Among the compounds investigated, the In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ exhibits the highest bulk lithium ion conductivity of 1.8×10⁻⁴ S/cm at 50 °C with an activation energy of 0.51 eV. The diffusivity (“component diffusion coefficient”) obtained from the AC conductivity and powder XRD data falls in the range 10⁻¹⁰-10⁻⁷ cm²/s over the temperature regime 50-200 °C, which is extraordinarily high and comparable with liquids. Substitution of Al, Co, and Ni for Nb in Li₅La₃Nb₂O₁₂ was found to be unsuccessful under the investigated conditions.     

Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

Effect of surface fluorination and conductive additives on the electrochemical behavior of lithium titanate (Li4/3Ti5/3O4) for lithium ion battery

Effect of surface fluorination and conductive additives on the charge/discharge behavior of lithium titanate (Li_4/3Ti_5/3O₄) has been investigated using F₂ gas and vapor grown carbon fiber (VGCF). Surface fluorination of Li_4/3Ti_5/3O₄ was made using F₂ gas (3 × 10⁴ Pa) at 25-150 °C for 2 min. Charge capacities of Li_4/3Ti_5/3O₄ samples fluorinated at 70 °C and 100 °C were larger than those for original sample at high current densities of 300 and 600 mA/g. Optimum fluorination temperatures of Li_4/3Ti_5/3O₄ were 70 °C and 100 °C. Fibrous VGCF with a large surface area (17.7 m²/g) increased the utilization of available capacity of Li_4/3Ti_5/3O₄ probably because it provided the better electrical contact than acetylene black (AB) between Li_4/3Ti_5/3O₄ particles and nickel current collector.     

Exfoliated nanoplatelets of an Aurivillius phase, Bi3.25La0.75Ti3O12: Characterisation by X-ray diffraction and by high-resolution electron microscopy

Nanoparticles of the Aurivillius phase La-substituted BTO (Bi_4−xLa_xTi₃O₁₂, with x=0.75) were obtained through a chemical lithiation process. They have been characterised by X-ray diffraction and transmission electron microscopy (diffraction and imaging at high resolution). The defect-free particles are platelet-shaped with the c large axis perpendicular to the plane. From high-resolution images, it is clear that the delamination process occurs at the level of the (Bi₂O₂)²⁺ intermediate layer and is destructive for this layer. The smallest thickness measured corresponds to one cell parameter (3.3 nm) but a large range of thicknesses have been observed: this suggests that the lithium insertion does not take place in all (Bi₂O₂)²⁺ layers, despite a large excess of lithium and a long reaction time. This is confirmed by ICP analysis, which leads to a formula Li_0.99Bi_3.25La_0.77Ti_3.00O₁₂ for the lithiated compound. This behaviour towards lithium intercalation differs from those observed with BTO in literature, where lithium insertion is reported as occurring in every (Bi₂O₂)²⁺ layer. Possible explanations for this difference are advanced based on microstructural and structural considerations.     

High-performance thin-film Li4Ti5O12 electrodes fabricated by using ink-jet printing technique and their electrochemical properties

Li₄Ti₅O₁₂ thin-film anode with high discharge capacity and excellent cycle stability for rechargeable lithium ion batteries was prepared successfully by using ink-jet printing technique. The prepared Li₄Ti₅O₁₂ thin film were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, cyclic voltammograms, and galvanostatic charge–discharge measurements. It was found that the average thickness of 10-layer Li₄Ti₅O₁₂ film was about 1.7~1.8 μm and the active material Li₄Ti₅O₁₂ in the thin film was nano-sized about 50–300 nm. It was also found that the prepared Li₄Ti₅O₁₂ thin film exhibited a high discharge capacity of about 174 mAh/g and the discharge capacity in the 300th cycle retained 88% of the largest discharge capacity at a current density of 10.4 μA/cm² in the potential range of 1.0–2.0 V.     

Composition and structure of acid leached LiMn2−yTiyO4 (0.2≤y≤1.5) spinels

Lithium manganese titanium spinels, LiMn_2−yTi_yO₄, (0.2≤y≤1.5) have been synthesized by solid-state reaction between TiO₂ (anatase), Li₂CO₃ and MnCO₃. Li⁺ was leached from the powdered reaction products by treatment in excess of 0.2 N HCl at 85 °C for 6 h, under reflux. The elemental composition of the acidic solution and solid residues of leaching has been determined by complexometric titration, atomic absorption spectroscopy and X-ray fluorescence analysis. Powder X-ray diffraction was used for structural characterization of the crystalline fraction of the solid residues. It has been found that the amount of Li⁺ leached from LiMn_2−yTi_yO₄ decreases monotonically with increasing y in the interval 0.2≤y≤1.0 and abruptly drops to negligibly small values for y>1.0. The content of Mn and Li in the liquid phase and of Mn and Ti in the solid (amorphous plus crystalline) residue, were related to the composition and cation distribution in the pristine compounds. A new formal chemical equation describing the process of leaching and a mechanism of the structural transformation undergone by the initial solids as a result of Li⁺ removal has been proposed.     

高倍率尖晶石型Li_4Ti_5O_(l2)/TiN锂离子电池负极材料的合成及其电化学性能

以乙酰丙酮(ACAC)为螯合剂、聚乙二醇(PEG)为分散剂,采用溶胶-凝胶法合成了尖晶石型Li4Ti5Ol2/TiN材料.考察了TiN膜对尖晶石型Li4Ti5Ol2锂离子电池负极材料电化学性能的影响.利用X射线光电子能谱(XPS)对Li4Ti5O12表面的TiN膜进行了分析.X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明,Li4Ti5Ol2/TiN材料为结晶良好的亚微米纯相尖晶石型钛酸锂.电化学性能测试表明,该材料的首次放电比容量为173.0mAh·g-1,并且具有良好的循环性能,以0.2C、1C、2C、5C倍率放电进行测试,10次循环后比容量分别为170.6、147.6、135.6、111.0mAh·g-1,较之表面无TiN膜的钛酸锂材料表现出更好的倍率特性.循环伏安曲线(CV),交流阻抗图谱(EIS)进一步论证了TiN膜改善了尖晶石型Li4Ti5Ol2锂离子电池负极材料的电化学性能.     

Synthesis, structure and electrical properties of Cu3.21Ti1.16Nb2.63O12 and the CuOx-TiO2-Nb2O5 pseudoternary phase diagram

Subsolidus phase relations in the CuO_x-TiO₂-Nb₂O₅ system were determined at 935 °C. The phase diagram contains one new phase, Cu_3.21Ti_1.16Nb_2.63O₁₂ (CTNO) and one rutile-structured solid solution series, Ti_1−3xCu_xNb_2xO₂: 0<x<0.2335 (35). The crystal structure of CTNO is similar to that of CaCu₃Ti₄O₁₂ (CCTO) with square planar Cu²⁺ but with A site vacancies and a disordered mixture of Cu⁺, Ti⁴⁺ and Nb⁵⁺ on the octahedral sites. It is a modest semiconductor with relative permittivity ∼63 and displays non-Arrhenius conductivity behavior that is essentially temperature-independent at the lowest temperatures.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

LiFePO4在饱和LiNO3溶液中的锂化行为

锂离子电池是目前应用最广泛的二次电池,均利用有机电解液。然而,有机体系锂离子电池存在易燃、易爆的安全隐患,限制了其使用范围。水溶液锂离子电池作为一类新型的二次电池[1￣10],使用水溶液电解液代替有机电解液,消除了因有机电解液与电极材料反应形成枝晶可能造成的燃烧、爆炸等安全隐患,使其在低电压电池如铅酸电池、碱锰电池等领域的应用有很大的竞争潜力[10]。目前,大量研究集中在选择合适的电极材料来组装水溶液锂离子电池,文献报道的水溶液锂离子电池正极材料主要有LiMnO4[1￣9]、LiNi1-xCoO2[10],但是LiMnO4在循环约20次后容…     

A comparison of the transport properties of lithium-stuffed garnets and the conventional phases Li3Ln3Te2O12

The structures of new phases Li₆CaLa₂Sb₂O₁₂ and Li_6.4Ca_1.4La₂Sb₂O₁₂ have been characterised using neutron powder diffraction. Rietveld analyses show that both compounds crystallise in the space group la3?d and contain the lithium cations in a complex arrangement with occupational disorder across oxide tetrahedra and distorted oxide octahedra, with considerable positional disorder in the latter. Variable temperature neutron diffraction experiments on Li_6.4Ca_1.4La₂Sb₂O₁₂ show the structure is largely invariant with only a small variation in the lithium distribution as a function of temperature. Impedance spectroscopy measurements show that the total conductivity of Li₆CaLa₂Sb₂O₁₂ is several orders of magnitude smaller than related lithium-stuffed garnets with σ=10⁻⁷ S cm⁻¹ at 95 °C and an activation energy of 0.82(3) eV. The transport properties of the conventional garnets Li₃Gd₃Te₂O₁₂, Li₃Tb₃Te₂O₁₂, Li₃Er₃Te₂O₁₂ and Li₃Lu₃Te₂O₁₂ have been evaluated and consistently show much lower values of conductivity, σ≤4.4×10⁻⁶ S cm⁻¹ at 285 °C and activation energies in the range 0.77(4)≤E_a/eV≤1.21(3).     

High dielectric constant PrYxOy sensing films electrolyte-insulator-semiconductor pH-sensor for the detection of urea

In this paper, we describe the structural and sensing properties of high-k PrY_xO_y sensing films deposited on Si substrates through reactive co-sputtering. Secondary ion mass spectrometry and atomic force microscopy were employed to analyze the compositional and morphological features of these films after annealing at various temperatures. The electrolyte-insulator-semiconductor (EIS) device incorporating a PrY_xO_y sensing membrane that had been annealed at 800 °C exhibited good sensing characteristics, including a high sensitivity (59.07 mV pH⁻¹ in solutions from pH 2 to 12), a low hysteresis voltage (2.4 mV in the pH loop 7 → 4 → 7 → 10 → 7), and a small drift rate (0.62 mV h⁻¹ in the buffer solution at pH 7). The PrY_xO_y EIS device also showed a high selective response towards H⁺. This improvement can be attributed to the small number of crystal defects and the large surface roughness. In addition, the enzymatic EIS-based urea biosensor incorporating a high-k PrY_xO_y sensing film annealed at 800 °C allowed the potentiometric analysis of urea, at concentrations ranging from 1 to 16 mM, with a sensitivity of 9.59 mV mM⁻¹.     

Series of compositions Bi2(M′xM1−x)4O9 (M′, M=Al, Ga, Fe; 0≤x≤1) with mullite-type crystal structure: Synthesis, characterization and O/O exchange experiment

Series of compositions Bi₂(M′_xM_1−x)₄O₉ with x=0.0, 0.1,…, 1.0 and M′/M=Ga/Al, Fe/Al and Fe/Ga were synthesized by dissolving appropriate amounts of corresponding metal nitrate hydrates in glycerine, followed by gelation, calcination and final heating at 800 °C for 24 h. The new compositions with M′/M=Ga/Al form solid-solution series, which are isotypes to the two other series M′/M=Fe/Al and Fe/Ga. The XRD data analysis yielded in all cases a linear dependence of the lattice parameters related on x. Rietveld structure refinements of the XRD patterns of the new compounds, Bi₂(Ga_xAl_1−x)₄O₉ reveal a preferential occupation of Ga in tetrahedral site (4 h). The IR absorption spectra measured between 50 and 4000 cm⁻¹ of all systems show systematic shifts in peak positions related to the degree of substitution. Samples treated in ¹⁸O₂ atmosphere (16 h at 800 °C, 200 mbar, 95% ¹⁸O₂) for ¹⁸O/¹⁶O isotope exchange experiments show a well-separated IR absorption peak related to the M-¹⁸O_c-M vibration, where O_c denotes the common oxygen of two tetrahedral type MO₄ units. The intensity ratio of M-¹⁸O_c/M-¹⁶O_c IR absorption peaks and the average crystal sizes were used to estimate the tracer diffusion coefficients of polycrystalline Bi₂Al₄O₉ (D=2×10⁻²² m²s⁻¹), Bi₂Fe₄O₉ (D=5×10⁻²¹ m²s⁻¹), Bi₂(Ga/Al)₄O₉ (D=2×10⁻²¹ m²s⁻¹) and Bi₂Ga₄O₉ (D=2×10⁻²⁰ m²s⁻¹).     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

A novel nonenzymatic sensor based on LaNi0.6Co0.4O3 modified electrode for hydrogen peroxide and glucose

In this paper, LaNi_0.6Co_0.4O₃ (LNC) nanoparticles were synthesized by the sol–gel method, and the structure and morphology of LNC nanoparticles were characterized by X-ray diffraction spectrum, scanning electron microscopy and transmitting electron microscopy. And then, LNC was used to modify carbon paste electrode (CPE) without any adhesive to fabricate hydrogen peroxide and glucose sensor, and the results demonstrated that LNC exhibited strong electrocatalytical activity by cyclic voltammetry and amperometry. In H₂O₂ determination, linear response was obtained in the concentration range of 10 nM–100 μM with a detection limit of 1.0 nM. In glucose determination, there was the linear region of 0.05–200 μM with a detection limit of 8.0 nM. Compared with other reports, the proposed sensor also displayed high sensitivity toward H₂O₂ (1812.84 μA mM⁻¹ cm⁻²) and glucose (643.0 μA mM⁻¹ cm⁻²). Moreover, this prepared sensor was applied to detect glucose in blood serum and hydrogen peroxide in toothpaste samples with satisfied results, indicating its possibility in practical application.     

Polyol-mediated synthesis of Li4Ti5O12 nanoparticle and its electrochemical properties

Li₄Ti₅O₁₂ nanoparticles were precipitated from ethylene glycol solution of titanium tetra isopropoxide (Ti(O-iPr)₄) and Li₂O₂ by refluxing at 197 °C for 12 h. The obtained particles were filtered and dried at 100 °C for 12 h, and the dried powder samples were heated at 320, 500 and 800 °C for 3 h. The X-ray diffraction patterns of the obtained samples exhibited a good fit with the spinel phase. The field emission-SEM images of the dried powder sample and the samples heated at 320, 500 and 800 °C for 3 h showed a uniform spherical morphology with a particle size of 5, 8, 10 and 400 nm, respectively. According to the results of electrochemical testing, the dried powder sample and the samples heated at 320, 500, and 800 °C for 3 h showed initial capacities of 200, 310, 320, and 260 mA h/g, respectively, at a current density of 0.05 mA/cm². Nanosized (6–8 nm) particles with good crystallinity were obtained by controlling the synthesis conditions. The sample heated at 500 °C for 3 h exhibited a high capacity and an excellent rate capability over 60 cycles.     

Synthesis, structure, and ionic conductivity of Na5Li3Ti2S8

The compound Na₅Li₃Ti₂S₈ has been synthesized by the reaction of Ti with a Na/Li/S flux at 723 K. Na₅Li₃Ti₂S₈ crystallizes in a new structure type with four formula units in space group C2/c of the monoclinic system. The structure contains three crystallographically independent Na⁺ cations and two crystallographically independent Li⁺ cations. Na₅Li₃Ti₂S₈ possesses a channel structure that features two-dimensional layers built from Li(1)S₄ and TiS₄ tetrahedra. The layers, which are stacked along c, comprise eight-membered rings and sixteen-membered rings. Na(3)⁺ cations are located between the eight-membered rings and Na(1)⁺, Na(2)⁺, and Li(2)⁺ cations are located between the sixteen-membered rings. These cations are each octahedrally coordinated by six S²⁻ anions. The ionic conductivity σ_T of Na₅Li₃Ti₂S₈ ranges from 8.8×10⁻⁶ S/cm at 303 K to 3.8×10⁻⁴ S/cm at 483 K. The activation energy E_a is 0.40 eV.     

Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

La0.6Sr1.4MnO4 layered perovskite anode material for intermediate temperature solid oxide fuel cells

La_0.6Sr_1.4MnO₄ (LSMO₄) layered perovskite with K₂NiF₄ structure was prepared and evaluated as anode material for La_0.8Sr_0.2Ga_0.83Mg_0.17O_3 − δ (LSGM) electrolyte supported intermediate temperature solid oxide fuel cells (IT-SOFCs). X-ray diffraction results show that LSMO₄ is redox stability. Thermal expansion coefficient of LSMO₄ is close to that of LSGM electrolyte. By adopting LSMO₄ as anode and La_0.6Sr_0.4Co_0.8Fe_0.2O₃ (LSCF) as cathode, maxium power densities of 146.6, 110.9 mW cm^− 2 with H₂ fuel at 850, 800 °C and 47.3 mW cm^− 2 with CH₄ fuel at 800 °C were obtained, respectively. Further, the cell demonstrated a reasonably stable performance under 180 mA cm^− 2 for over 40 h with H₂ fuel at 800 °C.     

Synthesis, structural characterization and Li ion conductivity of a new vanado-molybdate phase, LiMg3VMo2O12

A new vanado-molybdate LiMg₃VMo₂O₁₂ has been synthesized, the crystal structure determined an ionic conductivity measured. The solid solution Li_2−zMg_2+zV_zMo_3−zO₁₂ was investigated and the structures of the z=0.5 and 1.0 compositions were refined by Rietveld analysis of powder X-ray (XRD) and powder neutron diffraction (ND) data. The structures were refined in the orthorhombic space group Pnma with a∼5.10, b∼10.4 and c∼17.6 Å, and are isostructural with the previously reported double molybdates Li₂M₂(MoO₄)₃ (M=M²⁺, z=0). The structures comprise of two unique (Li/Mg)O₆ octahedra, (Li/Mg)O₆ trigonal prisms and two unique (Mo/V)O₄ tetrahedra. A well-defined 1:3 ratio of Li⁺:Mg²⁺ is observed in octahedral chains for LiMg₃VMo₂O₁₂. Li⁺ preferentially occupies trigonal prisms and Mg²⁺ favours octahedral sheets. Excess V⁵⁺ adjacent to the octahedral sheets may indicate short-range order. Ionic conductivity measured by impedance spectroscopy (IS) and differential scanning calorimetry (DSC) measurements show the presence of a phase transition, at 500-600 °C, depending on x. A decrease in activation energy for Li⁺ ion conductivity occurs at the phase transition and the high temperature structure is a good Li⁺ ion conductor, with σ=1×10⁻³-4×10⁻² S cm⁻¹ and E_a=0.6 to 0.8 eV.