氯离子侵蚀下钢筋在混凝土中腐蚀行为的EIS研究

应用电化学阻抗谱（EIS）和氯离子探针技术，研究在氯化物侵蚀作用下混凝土中钢筋的腐蚀行为.结果表明，钢筋混凝土体系的阻抗谱中包含两个时间常数，分别对应于界面的双电层和钢筋表面的混凝土保护层.自行研制的氯离子探针可连续、无损地测量钢筋/混凝土界面的氯离子浓度.根据腐蚀反应电阻Rct、Warburg阻抗等元件参数和界面氯离子浓度的变化，讨论了混凝土中钢筋腐蚀发生、发展各阶段界面化学环境及钢筋腐蚀参数的变化规律.     

环氧树脂涂覆LY12铝合金在NaCl溶液中的阻抗模型

分别研究了裸LY12铝合金及涂覆环氧树脂涂层后合金在3.5％NaCl溶液中的电化学阻抗谱（EIS）.结果表明,LY12铝合金在点蚀电位以下阻抗谱上出现两个容抗弧,高频段对应Cl－参与的成膜阻抗,低频段对应铝阳极溶解的电化学反应阻抗.合金发生点蚀后出现低频感抗弧.合金/电极在NaCl溶液中先发生涂层吸水,当水及O2抵达基体后建立起电化学反应界面,合金遭受腐蚀；受涂层阻挡的影响,腐蚀产物的扩散逐渐成为控制步骤；当扩散速度较慢的Cl－抵达涂层/金属界面后,与界面处聚集的腐蚀产物间发生化学反应,完成成膜过程,阻抗谱上出现盐膜的阻抗,而扩散阻抗消失.提出了不同浸泡失效阶段涂层电极体系的阻抗模型.     

钌镧氧化物涂层在NaCl 溶液中的电化学阻抗谱(EIS)研究

测量了钌镧氧化物涂层的电化学阻抗谱(EIS), 结合循环伏安(CV)及扫描电子显微镜形貌分析, 研究了钌镧氧化物涂层阳极在3.5% NaCl 溶液中电化学表面结构及电化学行为. 在非析氯反应区间, 该涂层EIS 数据的最佳拟合等效电路是R_s(R_ctQ_dl), 在析氯反应区间, 其等效电路为R_s(R_fQ_f)(R_ctWQ_dl). 高频段阻抗行为对应涂层的物理阻抗, 低频段对应涂层与溶液界面的电化学反应阻抗. 实验结果表明, 随着La 浓度增加, 氧化膜及双电层的伪电容增大, 且在La 含量30mol%时达到最大值, 与CV实验结果一致, 证明了加入La 能提高RuO₂涂层的电催化活性. 但在析氯反应区间, 涂层氧化膜的导电性在含La 大于30 mol%之后迅速下降, 在低频段产生Warburg 阻抗, 与其表面钝化和特性吸附现象有关,这是导致含La 70 mol%时电催化活性急剧下降的原因.     

电化学阻抗谱法研究铈改性TiO2纳米管阵列光电极裂解水产氢动力学

通过阳极氧化法在纯钛板上制备TiO2纳米管阵列电极.在光电化学电解池阳极中加入供电子物质乙二醇,显著减小了TiO2纳米管的电荷传递阻抗,促进了光电催化裂解水产氢反应.采用阴极电沉积和阳极氧化法制备了单质铈和氧化铈共同改性的TiO2纳米管阵列半导体光阳极,其平带电位向电负方向移动.采用电化学阻抗谱法(EIS)对改性后TiO2纳米管阵列在光电催化裂解水产氢中的电子传输性能以及界面性质进行了表征,确定了各阻抗弧对应的电极过程.采用合理的等效电路模型计算了电极的电子传输动力学参数.结果表明,经铈改性后的TiO2纳米管阵列膜电阻明显减小,有利于氢气的产生.探讨了单质铈与氧化铈促进TiO2纳米管阵列电荷传输的作用机理.     

新型的钛基Ni-Sn/Ti电极的制备及对甲醇氧化反应的电催化活性

利用电热法,一步制备出新型的钛基Ni-Sn/Ti电极(Ni8Sn/Ti, Ni7Sn3/Ti 和 Ni/Ti)。扫描电镜（SEM）图像表明,催化剂以片状的纳米颗粒形式沉积于钛基体上。利用电化学伏安技术、电位阶跃法和电化学交流阻抗谱（EIS）,研究了这些电极在1mol.L�1NaOH溶液中对甲醇氧化反应的电催化活性。研究表明,与Ni7Sn3/Ti,Ni/Ti以及多晶镍电极相比,Ni8Sn/Ti电极对甲醇氧化反应表现出更高的阳极氧化电流和更低的起始电位。EIS分析表明,在本文所考察的阳极电位和甲醇浓度下,Ni8Sn/Ti电极对甲醇氧化反应显示出极低的电荷传递电阻。结果表明,这种新型的钛基Ni8Sn/Ti电极对甲醇氧化反应具有极高的电催化活性。     

液/液界面的电化学阻抗谱测量Ⅰ: 四电极系统中各类界面阻抗的分析

本文系统地研究了将阻抗谱技术应用于液/液界面电化学领域时所出现的问题。提出了四电极系统中液/液界面交流阻抗的表达式。从理论上分析了电解池参数和仪器输入参数对所得交流阻抗曲线的影响。     

电极/溶液界面pH值的现场测量

一般认为阴极表面功能陶瓷电沉积层的形成是由于基底 /溶液界面化学环境变化造成的 [1,2 ] ,但目前还没有直接的实验数据加以证明 .原位测量电极 /溶液界面 p H的变化存在两方面的困难 :(1 )传统方法是采用玻璃 p H计 ,由于其体积较大、强度脆弱等原因 ,使其在测量固 /液界面化学环境变化的应用方面受到一定限制 [3 ] ;(2 )将 p H微探针置于电极表面 ,将会影响功能陶瓷在电极表面的沉积 ,从而使测定的界面 p H值不能真实反映电沉积过程中固 /液界面化学环境的变化 .本文基于功能陶瓷电沉积过程不受影响的情况下现场直接测量电极 /溶液界面…     

氯离子侵蚀下钢筋在混凝土中腐蚀行为的EIS研究

应用电化学阻抗谱(EIS)研究环境介质中氯离子对混凝土中钢筋腐蚀行为的影响.结果表明,在测量的频率范围内,钢筋混凝土体系的阻抗谱图包含两个时间常数,分别对应于界面的双电层和钢筋表面的混凝土保护层.其低频段的半圆有些压扁,表明界面双电层的充放电行为偏离理想电容器,可归因于钢筋表面的不均一性.在浸泡后期,低频段出现拖尾,同时电荷转移电阻Rct减小了近两个数量级,这是由于钢筋表面的钝化膜已经破裂,发生活性腐蚀,况且氯离子浓度的增大加速了腐蚀发展过程.讨论了混凝土中在钢筋腐蚀发生,发展的过程中,其腐蚀电位Ecorr以及等效电路中的Rct和Warburg阻抗等元件的变化特征.     

嵌入化合物电极的电化学阻抗谱: 模型与理论模拟

建立了单个嵌入化合物颗粒、混合颗粒、厚度均匀多孔电极层以及非均匀、多层多孔电极层的理论模型,模拟得了了上述模型的相对应电化学阻抗谱（EIS）特征.结果表明,单个颗粒和混合颗粒表现出相似的阻抗谱特征,均由高频区域内与锂离子通过固体电解质相界面（SEI）膜过程相关的R_SEI‖C_SRI半圆,与电荷传递过程相关的R_ct‖C_dl半圆以及锂离子在固体颗粒内部的扩散相关的斜线三部分组成.对于非均匀、多层多孔嵌入电极而言,一个个新奇的现象就是在阻抗谱中会出现三个半圆,影响第三个半圆现现并形成的因素主要为电极中的颗粒尺寸分布以及电极层的厚度分布,也就是说电极片中出现不同尺寸分布的颗粒以及形成薄厚两种电极层的时候,容易导致阻抗谱中出现第三个半圆.     

“电极/溶液”界面的椭圆偏振测量技术研究进展

椭圆偏振测量技术是通过解析偏振光束在界面上或薄膜中反射或透射时偏振状态的变化,获取界面或薄膜的厚度、复折射率等性质的一种光学方法,是一种高灵敏度、非破坏性的原位实时表征技术,被广泛应用于“电极/溶液”界面的研究. 本文简要介绍了椭圆偏振测量技术的基本原理及其最新发展,并着重评述了能源电化学、材料电化学、电分析与生物电化学等领域中,应用椭圆偏振测量技术研究“电极/溶液”界面的现状.     

Simultaneous quartz crystal microbalance-electrochemical impedance spectroscopy study on the adsorption of anti-human immunoglobulin G and its immunoreaction at nanomaterial-modified Au electrode surfaces.

The quartz crystal microbalance method (QCM), in combination with electrochemical impedance spectroscopy (EIS), has been utilized to monitor in situ anti-human IgG adsorption on several Au-based surfaces, bare Au, nanogold/4-aminothiophenol (4AT)/Au, and multi-walled carbon nanotubes (MWCNT)/Au, and succeeding human IgG reactions. Also, the immobilization protocol of anti-human IgG via its glutaraldehyde (GA) cross-linking with self-assembled 4AT on an Au electrode and the subsequent surface immunoreaction were examined. The resonant frequency (f(0)) and the motional resistance (R(1)) of the piezoelectric quartz crystal (PQC) as well as electrochemical impedance parameters were measured and discussed. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the ferricyanide/ferrocyanide couple were examined before and after electrode modification, the antibody adsorption and antibody-antigen reactions. We found that the amount for antibody adsorption was the greatest on the colloid Au modified surface, and that at MWCNT ranked the second, while specific bioactivity was almost identical on the four kinds of surfaces. Two parameters simultaneously obtained at the colloid Au modified surface, Deltaf(0) and DeltaC(s) (interfacial capacitance), have been used to estimate the association constant of the immunoreaction.     

SiO的电化学性能及其电极过程动力学研究

本文采用恒流充放电考察SiO的电化学性能，并在0.5 MHz至0.001 Hz的频率范围内，通过交流阻抗技术研究SiO电极在首次嵌锂反应中的电极过程。对不同电压区间下测得的交流阻抗图谱，提出不同的等效电路模型并对结果进行了拟合。通过拟合结果，探讨了SiO电极过程动力学以及嵌锂过程中电极界面的变化特性。     

Investigation of Ig.G adsorption and the effect on electrochemical responses at titanium dioxide electrode

The adsorption of Immunoglobulin G on a titanium dioxide (TiO(2)) electrode surface was investigated using (125)I radiolabeling and electrochemical impedance spectroscopy (EIS). (125)I radiolabeling was used to determine the extent of protein adsorption, while EIS was used to ascertain the effect of the adsorbed protein layer on the electrode double layer capacitance and electron transfer between the TiO(2) electrode and the electrolyte. The adsorbed amounts of Ig.G agreed well with previous results and showed approximately monolayer coverage. The amount of adsorbed protein increased when a positive potential was applied to the electrode, while the application of a negative potential resulted in a decrease. Exposure to solutions of Ig.G resulted in a decrease of the double layer capacitance (C) and an increase in the charge-transfer resistance (R(2)) at the electrode solution interface. As more Ig.G adsorbed onto the electrode surface, the extent of C and R(2) variation increased. These capacitance and charge-transfer resistance variations were attributed to the formation of a proteinaceous layer on the electrode surface during exposure.     

Study of the Adsorption of Glutathione on a Gold Electrode by Using Electrochemical Quartz Crystal Impedance, Electrochemical Impedance Spectroscopy, and Cyclic Voltammetry

Adsorption of a biological peptide, glutathione, on a gold electrode was studied by using electrochemical quartz crystal impedance (EQCI), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) techniques. The time courses of responses of piezoelectric and electrochemical impedance parameters were simultaneously obtained during the adsorption processes of the two forms of peptide, oxidized and reduced glutathione. It was found that the frequency curve due to the oxidized glutathione (GSSG) adsorption exhibited a character of a sum of two exponential functions. For reduced glutathione (GSH), the frequency adsorption curve could be expressed by a first-order reaction kinetic model and the corresponding kinetic parameters at different amounts of GSH were obtained. The heterogeneous charge-transfer rate constants of ferricyanide/ferrocyanide before and after the peptide adsorption were determined by CV and EIS methods, respectively. According to the simple equivalent electric network of the electrochemical interface, the electrochemical impedance parameters were also obtained. The results showed that the proposed method should be found in wider applications in interfacial biochemistry studies since these combined techniques have advantages in real time multidimensional information including electrochemical and electrochemical impedance parameters. Copyright 2000 Academic Press.     

三维有序金掺杂纳米TiO_2修饰电极用于抗肿瘤药物与DNA相互作用的研究

利用模板法在氧化铟锡(ITO)电极表面制备了三维有序多孔结构的金掺杂纳米Ti O2薄膜修饰电极(3DOM GTD/ITO),并在此修饰电极上成功固定小牛胸腺DNA(ct DNA),从而构建了一种新型的DNA生物传感器(DNA/3DOM GTD/ITO),并通过透射电镜(TEM)、扫描电镜(SEM)对修饰电极的表面形貌进行表征。采用电化学交流阻抗(EIS)法研究了ct DNA在3DOM GTD/ITO修饰电极表面的固定情况,结果表明,ct DNA已被成功地固定在3DOM GTD/ITO修饰电极表面。采用循环伏安法、微分脉冲伏安法等电化学方法研究了抗肿瘤药物槲皮素(Qu)在3DOM GTD/ITO修饰电极表面的电化学性质及与ct DNA的相互作用。结果表明,Qu在3DOM GTD/ITO修饰电极表面有1对准可逆的氧化还原峰,其氧化还原反应为2电子和2质子的转移过程。Qu可与固定在修饰电极上的ct DNA发生较强的结合作用,其结合常数(K)为3.61×106L/mol。循环伏安实验、紫外-可见吸收光谱、分子荧光光谱、圆二色性光谱均表明Qu与ct DNA之间的相互作用模式为嵌插作用。Qu与ct DNA的碱基结合具有序列选择性,对Qu与聚(d G-d C)及聚(d A-d T)的结合常数进行计算,得到结合常数比K(d G-d C)/K(d A-d T)=3.5,表明Qu与ct DNA发生嵌插作用时更倾向于结合在GC富集区域。     

非标记型河虾免疫传感器的制备及应用

四乙氧基硅在HCl催化下水解形成硅溶胶。将硅溶胶与河虾抗体混合均匀后,涂于玻碳电极表面制备得非标记型河虾抗体免疫传感器。采用Fe(CN)63-/4-的磷酸盐缓冲溶液(pH 6.5)为测试底液,研究此传感器在免疫反应中的循环伏安和交流阻抗特性。结果显示免疫反应后传感器的循环伏安图上未出现新的氧化-还原峰,表明该免疫反应属于非氧化还原过程。采用交流阻抗监测电极表面,发现传感器阻抗值随虾过敏原浓度的增加而增大。对交流阻抗图进行分析,结果表明电极表面的免疫反应是一个受电子转移控制的过程。当虾过敏原浓度在0~10 ng/mL之间,电极表面电子转移阻抗的增加值与虾过敏原浓度呈线性关系,检出限为0.1 ng/mL(S/N=3)。该方法已成功应用于河虾制品中过敏原的测定。     

基于Pt/Au双金属修饰针灸针的非酶葡萄糖传感器

通过在不锈钢针灸针（AN）表面依次电沉积金（Au）纳米颗粒和铂（Pt）纳米颗粒,基于它们在AN表面的协同作用,实现了一种用于非酶葡萄糖检测的电化学生物传感器。首先,通过扫描电子显微镜对其功能界面（Pt/Au/AN）进行表征,结果显示类似卷心菜的纳米材料均匀致密地分布在AN表面。然后,通过循环伏安法和电化学阻抗法对Pt/Au/AN电极的电化学特性进行了研究。结果表明,与Au/AN或Pt/AN电极相比,Pt/Au/AN电极对葡萄糖氧化表现出优越的电催化活性。这表明双金属Pt/Au的接触界面是葡萄糖氧化的重要电催化位点。在pH7.4的模拟生理介质中,制得传感器的线性范围为0.1~35 mmol·L^-1,检测限为0.0763 mmol·L^-1,对葡萄糖的检测表现出较高的灵敏度和良好的抗干扰性能、稳定性。此外,该传感器已成功用于人体血清葡萄糖的检测。     

Microelectrode Combinations of Gold and Polypyrrole Enable Highly Stable Two-electrode Electrochemical Impedance Spectroscopy Measurements under Turbulent Flow Conditions

An electrochemical impedance spectroscopy (EIS) sensor design is proposed based on a standard interdigitated electrode layout in which the smaller working electrode consists of gold (Au) whereas the larger combined counter and reference electrode is coated with a porous layer of polypyrrole (PPy) doped with polystyrene sulfonate (PSS) (PPy : PSS). Each electrode material was first characterized by EIS in a standard 3-electrode setup with subsequent spectra fitting by a modified Randles equivalent circuit. The differences in the spectra obtained by the PPy : PSS coated electrodes can be explained by an increased electroactive surface area due to the porous polymer film. The changes in morphology of the film are discussed with respect to the evolution of the elements of the electric equivalent circuit. When applying the Au/PPy : PSS electrode combination to a standard 2-electrode arrangement, the enlarged highly electroactive surface area of the PPy : PSS coating lowers the interfacial impedance in a way that mainly the gold working electrode contributes to the overall system impedance. Therefore, obtaining reproducible EIS signals depends only on the electrode's open-circuit potential (OCP) and on additional adsorption events at the gold electrode/electrolyte interface. We present a protocol for microelectrode coating with PPy : PSS, which enables highly stable 2-electrode EIS experiments without the need of a reference electrode. This combination is believed to be very useful if an integration of sensing electrodes inside Micro Total Analysis Systems is aspired.     

Li3V2(PO4)3电极过程及其锂离子脱嵌动力学研究(I)

采用溶胶凝胶法合成了Nasicon化合物Li₃V₂(PO₄)₃, 采用X射线衍射(XRD)对产品进行了物相分析. 采用充放电测试, 循环伏安(CV)研究了化合物的电化学性能和锂离子的脱嵌过程, 计算出Li^＋在固相中的扩散系数(10^－8 cm²•s^－1); 采用交流阻抗测试(EIS)研究了Li₃V₂(PO₄)₃的电极过程; 对两种类型的阻抗图谱提出不同等效电路模型并对结果进行了拟合; 研究了Li₃V₂(PO₄)₃电极过程动力学以及新鲜电极界面在充放电过程中的变化特性.     

Characterization of Electrode/Electrolyte Interface of ECIS Devices

Electric cell‐substrate impedance sensing requires low electrode/electrolyte interface impedance for effective biomedical and biophysical applications. Thus a complete understanding of physical processes involved in the formation of an electric double layer is required to design a low interface impedance device. This paper presents the numerical simulation of the impedance for the electrode/electrolyte interface of three‐electrode devices along with the practical realization for the effective workout of impedance sensing devices. The three‐electrode based impedance sensing devices along with phosphate buffered saline as electrolyte is simulated using COMSOL Multiphysics to evaluate the impedance of the electrode/electrolyte interface. Microfabrication technology is used to realize three‐electrode impedance sensing devices with diverse configuration which are used to measure the electrode/electrolyte interface impedance. The measured impedance data were then compared with the COMSOL simulated results and it is found that both the data sets fitted well with less than 5 % RSE. The results obtained from simulation and experiments indicate that the impedance due to double layer diffusion dominates in the low frequency region up to few kHz whereas electrolytic bulk resistance plays a major role in the higher frequency range. The experimental impedance data were further interpreted by electrochemical impedance spectroscopy analysis software to model the equivalent circuit of the electrochemical system.