质子交换膜燃料电池Nafion/PTFE复合膜的研究

在聚四氟乙烯(PTFE)多孔膜内浸入Nafion树脂,制成Nafion/PTFE复合膜用于质子交换膜燃料电池(PEMFC).该复合膜的Nafion含量在50%左右,在干态和湿态时的拉伸强度及水化/脱水过程中,其尺寸稳定性比Nafion均有所提高.在80 ℃,H2/O2压力为0.2/0.2 MPa条件下,用25 μm厚复合膜组装的电池性能优于Nafion117膜组装电池的性能.测量了复合膜的O2渗透率和含水量并与Nafion膜的性能作了比较.     

采用Nafion粘结剂的PEMFC氧电极研究

研究了聚合物电解质燃料电池（PEMFC）中以Nation溶液取代PTFE乳液作粘结剂的效果．并对催化剂层内Nafion含量进行了优化，同时探讨了气体工作压力和离子交换膜的影响，实验发现：1．使用Nafion溶液后显著提高电池性能，Nafion含量为2mg·cm－2时性能技好；2．气体压力增大改善了电池位能；3．使用Nafion115膜的电池性能优于使用Nafion117膜的电池．要进一步提高电池性能，减小欧姆控制区的斜率是必要的．     

直接甲醇燃料电池中的膜性能比较

制备了磺化聚醚醚酮(SPEEK)和磺化酚酞型聚醚砜(SPES-C)两种质子交换膜,考察了其质子导电和阻醇性能.实验发现,两种新型质子交换膜具有一定的化学稳定性和质子电导率,尤其在高温下两种新膜的质子电导率与Nafion膜接近.两种新膜的甲醇透过系数要比Nafion膜的低1～2个数量级.分别以两种新型膜和Nafion115膜为电解质制备了直接甲醇燃料电池膜电极,讨论了膜材料的性能对直接甲醇燃料电池性能的影响.结果表明,膜材料的阻醇性越好,电池的开路电压越高;膜的电导率越高,在较高电流密度区域内电池的性能越好.     

含杂萘联苯结构聚合物膜的直接甲醇燃料电池性能

质子交换膜是直接甲醇燃料电池(DMFC)的关键组成部分. 通过磺化制备了磺化杂萘联苯聚醚酮(SPPEK)、磺化杂萘联苯聚醚砜(SPPES)和磺化杂萘联苯聚醚砜酮(SPPESK)三种含杂萘联苯结构的新质子交换膜, 测试了其热稳定性、质子导电性和甲醇透过性能. SPPESK的热分解温度比相近离子交换容量(IEC)的SPPEK和SPPES约低100 ℃, 三种膜均具有良好的导电和阻醇性能; 分别以三种膜为电解质组装DMFC考察了其性能, DMFC的开路电压随膜的阻醇性的提高而增大, 三种膜的开路电压均高于Nafion115膜, 但在较高电流密度的区域三种新膜的性能均比Nafion115膜差.     

DMFC用PES/SPEEK共混阻醇质子交换膜

将磺化聚醚醚酮(SPEEK, 磺化度DS为68.3%)和聚醚砜(PES)两种聚合物共混制得PES/SPEEK共混膜. DSC研究表明两种聚合物之间具有较好的相容性, 因而共混膜均匀致密, 未发生大尺度相分离. PES的混入能有效降低膜的溶胀度及甲醇透过系数. 纯SPEEK 膜40 ℃时在1 mol•L−1甲醇水溶液中溶胀度达到160%, 45 ℃时就完全溶解, 而含30%(w)PES的共混膜在80 ℃时的溶胀度仅有15%. 室温下含20%−30%(w)PES的共混膜的甲醇透过系数为1×10−7 cm2•s−1左右, 比Nafion 115膜的透过系数小一个数量级. 尽管80 ℃下30%(w)PES/SPEEK共混膜的电导率与Nafion 115膜相当, 但由于共混膜的厚度比Nafion 115膜小1/3左右, 膜电阻较小, 因而其电池性能比Nafion 115膜的好.     

银在质子交换膜燃料电池空气阴极内促进氧传递研究

利用离子交换及随后的氢还原,将单质银负载在质子交换膜(Nafion)孔道内.TEM、XRD表征载银Nafion膜的结构,电化学极限电流法测定氧在载银Nafion膜内的扩散系数.结果表明,因银晶颗粒大于Nafion孔道直径,致使Nafion孔道有所扩张;氧在载银Nafion膜内的扩散系数是无银Nafion膜的4倍.据此,把银引入质子交换膜燃料电池空气阴极催化剂表面的Nafion薄层,则电池的性能在高电流密度下有明显的提高,显示了银对该电极内氧传递的促进作用.     

NafionTM膜表面改性用等离子体聚合方法提高膜的阳离子选择性

采用辉光放电等离子体聚合方法 ,以 C2 H4 和 NH3 为单体 ,在 Nafion TM膜表面沉积一层含氨基及酰氨基的类聚乙烯阴离子交换膜 ,提高了 Nafion TM膜对阳离子的选择性 ,同时不显著增加膜电阻 .由 SEM确定该等离子体聚合膜厚约 0 .5μm,用红外光谱及 X光电子能谱表征膜结构 .采用四电极法测量膜电阻 ,膜对质子的选择性由 Cu2 + 的迁移数 t Cu表征 ,用二室隔膜装置 (0 .2 5mol/L Cu Cl2 -0 .5mol/L HCl|等离子体处理膜 |1 mol/L HCl)测量 t Cu. O2 等离子体预处理 Nafion TM膜有利于沉积膜在 Nafion TM膜上的沉积并与 Nafion TM膜紧密结合 .经改性后的 Nafion TM膜电阻值仍然很小 ,在 1 mol/L HCl溶液中电阻小于 0 .5Ω· cm2     

质子交换膜对钒氧化还原液流电池性能的影响

采用溶液接枝聚合法制备了一种新型的质子交换膜PVDF-g-PSSA, 测定了PVDF-g-PSSA膜、Nafion 117 膜和PE01均相膜的离子交换能力和电导率, 并分别研究了以这3种膜为隔膜的钒电池的电化学性能. 实验结果表明, PVDF-g-PSSA膜具有优良的质子电导率和离子交换能力, 室温下其离子交换能力和质子电导率分别为1.13 mmol/g和3.22×10-2 S/cm, 在不同的充放电电流密度下, 以PVDF-g-PSSA膜为隔膜的钒电池的库仑效率和能量效率明显高于Nafion 117膜和PE01均相膜为隔膜的钒电池; PVDF-g-PSSA膜阻钒离子的渗透性能与PE01均相膜基本一致, 都明显优于Nafion 117膜的阻钒离子渗透能力.     

直接甲醇燃料电池用磺化聚醚醚酮膜初探

应用电化学方法研究了SPEEK膜的甲醇渗透性能.SPEEK膜具有比Nafion115膜低的甲醇渗透.以其作质子交换膜电解质组装的直接甲醇燃料电池(DMFCs)开路电压高于Nafion115膜组装的DMFC开路电压,但电池的放电性能尚待改进.本研究可为SPEEK应用于直接甲醇燃料电池提供一定的依据.     

丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

Reinforced and self-humidifying composite membrane for fuel cell applications

A novel preparation method for a composite proton exchange membrane with reinforced strength and self-humidifying property was developed. Using self-assembly method, highly dispersed poly(diallyldimethylammonium chloride) (PDDA) stabilized Pt nanoparticles were mounted onto the pores of poly(tetrafluoroethylene) (PTFE) porous film to serve the self-humidifying purpose. With Pt nanoparticles fixed on the PTFE pores, the potential problem of any short circuit because of the use of metal nanoparticles can be prevented. Pt-PDDA/PTFE substrate in the composite membrane can enhance the mechanical strength of the membrane and distribute self-humidifying layer adjacent to the anode side. Compared with the cells fabricated with conventional Nafion^® and PTFE/Nafion membranes, the performance of the cells with this composite membrane is dramatically improved under dry conditions. Electrochemical impedance spectroscopy technique revealed that these self-humidifying composite membranes could minimize membrane conductivity loss under dry conditions.     

Preparation,photocatalytic activity and mechanism of nano-Titania/Nafion hybrid membrane

Nano-Titania/Nafion (TiO₂/Nafion) hybrid membranes were prepared by recasting, using Nafion solution and TiO₂ anatase hydrosol as the raw materials. The microstructure of the hybrid membrane was characterized by X-ray diffraction, high-resolution transmission electron microscopy (HR-TEM), X-ray Photoelectron Spectroscopy and Fourier Transform Infrared Spectroscopy (FT-IR). The photocatalytic properties of TiO₂/Nafion hybrid membranes were evaluated. Furthermore, endurance of photocatalytic activity of the hybrid membrane was investigated. The results indicate that the TiO₂ Nanoparticles are bounded to Nafion molecule via Ti-O-S bonds and the formed flocculates are distributed homogeneously throughout the recasting Nafion membrane, while the initial pure anatase TiO₂ nanoparticles remain intact in re-crystallized membrane. The hybrid membranes possessed excellent photocatalytic activities with and without H₂O₂. Moreover, the degradation of photocatalytic activities has been better controlled with the presence of H₂O₂.     

Exfoliated Pt-clay/Nafion nanocomposite membrane for self-humidifying polymer electrolyte fuel cells

Monolayers of Pt nanoparticles of diameters of 2-3 nm with a high crystallinity were successfully anchored onto exfoliated nanoclay surfaces using a novel chemical vapor deposition process. Chemical bonding of Pt to the oxygen on the clay surface ensured the stability of the Pt nanoparticles, and hence, no leaching of Pt particles was observed after a prolonged ultrasonication and a rigorous mechanical agitation of Pt-clay in the Nafion solution during the membrane casting process. Systematic analysis using WAXD and TEM showed that the recasting process produced a new self-humidifying exfoliated Pt-clay/Nafion nanocomposite membrane with a high crystallinity and proton conductivity. In situ water production for humidification of the dry membranes without any external humidification was characterized by a combined water uptake and FTIR analysis of the as-prepared membrane after a single cell testing without using electrodes. The power density at 0.5 V of a single cell made of a Pt-clay/Nafion nanocomposite membrane was 723 mW/cm2, which is 170% higher than that made of a commercial Nafion 112 membrane of similar thickness. No compromise in mechanical properties was observed.     

In situ polymerization: A novel route for thermally stable proton-conductive membranes

In this paper, a new solvent-free route for preparing proton-conductive membranes is proposed. Flexible and fiber-supported polymer electrolyte membranes, as potential proton exchange membranes, were readily obtained by in situ polymerization of a homogenous solution that consisted of bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO, polymer)–monomer mixtures of styrene (ST) and divinylbenzene (DVB), which was pre-cast onto SEFAR PETEX fibers. Factors such as the components of the casting solution and the sulfonation time, were fully investigated. The membrane structure and components were confirmed by FTIR-ATR spectra and SEM-EDXA images, and the thermal stability was examined via TGA and DrTGA. The membrane exhibited a proton conductivity of about 0.07 S/cm at 100% humidity and at room temperature, which is close to that of Nafion 117 at identical conditions (around 0.08 S/cm), whereas its thickness (about 120 μm) was less than that of Nafion 117. The tensile strength and the elongation at the break of the membrane were 31.2 MPa and 71%, respectively, which are several times higher than those of Nafion (about 6.16 MPa tensile strength and 36% elongation ratio). The dimensional change ratio of the membrane between the wet and dry states was below 3%, which is much lower than that of Nafion 117. The membrane showed a high thermal stability up to 400 °C. The method can be applied to other compatible systems of (aromatic) polymers and (aromatic) monomers.     

Development of nano-catalyzed membrane for PEM fuel cell applications

Nano-catalyzed membrane with different platinum (Pt) catalyst loadings (0.25 to 1 mg cm^?2) was investigated for proton exchange membrane fuel cell applications, and the Pt loading on the Nafion membrane was prepared by non-equilibrium impregnation reduction method. The prepared catalyzed membranes were subjected to various characterisations, namely, X-ray diffraction, high-resolution scanning electron microscopy (HRSEM) with energy-dispersive X-ray, cyclic voltammetry, polarisation and electrochemical impedance spectroscopy. The polycrystalline fcc cubic structure and the particle size of Pt catalyst were estimated by X-ray diffraction analysis. The membrane with 0.4 mg cm^?2 of Pt loading exhibits a favourable surface morphology which is confirmed by HRSEM image. Electrochemical investigations were clearly evident that the uniform distributions of Pt particles with fine pores on Nafion membrane facilitated the three-phase boundary which leads to a better cell performance. Electrochemical impedance spectroscopy demonstrated that the cell constructed using 0.4 mg cm^?2 of platinum-loaded membrane has lower resistance than the other Pt loading.     

Preparation and characterization of sulfated zirconia (SO4/ZrO2)/Nafion composite membranes for PEMFC operation at high temperature/low humidity

Fine particle superacidic sulfated zirconia (SO₄²⁻/ZrO₂, S-ZrO₂) was synthesized by ameliorated method, and composite membranes with different S-ZrO₂ contents were prepared by a recasting procedure from a suspension of S-ZrO₂ powder and Nafion solution. The physico-chemical properties of the membranes were studied by ion exchange capacity (IEC) and liquid water uptake measurements, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, thermogravimetry–mass spectrometry (TG–MS) and Fourier transform infrared (FT-IR) spectroscopy. The results showed that the IEC of composite membrane increased with the content of S-ZrO₂, S-ZrO₂ was compatible with the Nafion matrix, the incorporation of the S-ZrO₂ could increase the crystallinity and also improve the initial degradation temperature of the composite membrane. The performance of single cell was the best when the S-ZrO₂ content was 15 wt.%, and achieved 1.35 W/cm² at 80 °C and 0.99 W/cm² at 120 °C based on H₂/O₂ and at a pressure of 2 atm, the performance of the single cell with optimized S-ZrO₂ was far more than that of the Nafion at the same condition (e.g. 1.28 W/cm² at 80 °C, 0.75 W/cm² at 120 °C). The 15 wt.% S-ZrO₂/Nafion composite membrane showed lower fuel cell internal resistance than Nafion membranes at high temperature and low relative humidity (RH).     

Preparation of Nafion/sulfonated poly(phenylsilsesquioxane) nanocomposite as high temperature proton exchange membranes

Nafion/sulfonated poly(phenylmethyl silsesquioxane) (sPPSQ) composite membranes are fabricated using homogeneous dispersive mixing and a solvent casting method for direct dimethyl ether fuel cell (DDMEFC) applications operated above 100 °C. The inorganic conducting filler, sPPSQ significantly affects the characteristics in the nanocomposite membranes by functionalization with an organic sulfonic acid to PPSQ. Moreover, sPPSQ content plays an important role in membrane properties such as microstructure, proton conductivity, fuel crossover, and single cell performance test. With increasing sPPSQ content in the nanocomposite membrane, the proton conductivity increased and fuel crossover decreased. However, in a higher temperature range above 110 °C, Nafion/sPPSQ 5 wt.% composite membrane has the highest proton conductivity. Also, the DME permeability for the composite membrane with higher sPPSQ content increased sharply. The excessive sPPSQ content caused a large aggregation of inorganic fillers, leading to the deterioration of membrane properties. In this study, the optimal sPPSQ content for maximizing the DDMEFC performance was 5 wt.%. Our nanocomposite membranes demonstrated proton conductivities as high as 1.57 × 10⁻¹ S/cm at 120 °C, which is higher than that of Nafion. The cell performances were compared to Nafion/sPPSQ composite membrane with Nafion 115, and the composite membrane with sPPSQ yielded better cell performance than Nafion 115 at temperatures ranging from 100 to 120 °C and at pressures from 1 to 2 bar.     

全钒液流电池磺化石墨烯/Nafion复合膜的研究

本文通过磺化石墨烯对Nafion膜进行改性,研究了磺化石墨烯/Nafion复合膜（GRS-Nafion复合膜）的吸水率、电阻率和钒离子迁移数. 结果表明,经磺化石墨烯改性之后,GRS-Nafion复合膜的面电阻和钒离子渗透率显著降低. 全钒液流电池的测试结果表明,GRS-Nafion复合膜有着更加优异的电化学性能,展示出GRS-Nafion复合膜在液流电池中的应用潜力.