聚丙烯/蒙脱土纳米复合材料的等温结晶研究

采用差示扫描量热法 (DSC)对插层聚合法制备的聚丙烯 /蒙脱土纳米复合材料 (PP MMT)的等温结晶过程进行了研究 .引入蒙脱土 (MMT)后 ,PP MMT的结晶速率大幅度提高 ,相对结晶度略有下降 .采用Avrami方程对结晶动力学进行研究 ,Avrami指数n≈ 3 .0 ,半结晶时间t1 2 大幅度降低 .采用Hoffman理论计算了PP MMT的球晶生长的单位面积表面自由能σe,结果表明σe 随MMT含量的增加逐渐降低     

插层聚合制备聚丙烯/蒙脱土纳米复合材料及其结构性能表征

将插层聚合的概念引入烯烃聚合,制备了聚丙烯／蒙脱土（PP／MMT）纳米复合材料。X射线衍射和TEM分析结果表明,蒙脱土在聚丙烯基体中达到了纳米级的分散,动态力学性能研究结果表明,在高于Tg的温度区域内PP／MMT纳米复合材料的储能模量（E′）成倍增加,加入8％的蒙脱土（MMT）,PP／MMT的E′提高近3倍。PP／MMT的玻璃化转变温度Tg有一定程度的提高,随蒙脱土含量的增加,PP／MMT的热分解温度和热变形温度（HDT）都有大幅度提高。     

动态扭振法研究聚甲基丙烯酸甲酸／蒙脱土纳米复合材料的本体插层聚合

用动态扭振法研究塑性塑料聚甲基丙烯酸甲酸（PMMA）／蒙脱土（MMT）复合体系的本体插层聚合，并试用处理交联体系固化的Folry理论，非平衡态热力学涨落理论和Avrami方程研究PMMA／MMT复合体系的本体插层聚合，求取表观活化能Ea.实验发现，PMMA／MMT插层聚合转化率曲线中后期与热固性树脂的固化曲线极为类似，表明剥离后的蒙脱土片层在复合材料中起到交联点的作用。     

动态扭振法研究聚甲基丙烯酸甲酯/蒙脱土纳米复合材料的本体插层聚合

用动态扭振法研究热塑性塑料聚甲基丙烯酸甲酯(PMMA)/蒙脱土(MMT)复合体系的本体插层聚合.并试用处理交联体系固化的Flory理论、非平衡态热力学涨落理论和Avrami方程研究PMMA/MMT复合体系的本体插层聚合,求取表观活化能Ea.实验发现,PMMA/MMT插层聚合转化率曲线中后期与热固性树脂的固化曲线极为类似,表明剥离后的蒙脱土片层在复合材料中起到交联点的作用.     

蒙脱土负载型引发剂的制备及在苯乙烯乳液聚合中的应用

通过正离子交换将引发剂AIBA负载在蒙脱土上制得负载型引发剂V50-MMT.进而采用原位乳液聚合方法引发苯乙烯聚合制备PS/MMT纳米复合材料.采用XRD、TGA、DSC、TEM和抽提等方法对负载型引发剂和纳米复合材料进行了表征.结果表明,负载过程中引发剂AIBA进入了MMT的片层之间;聚合过程中介于片层间的引发剂因发生分解一方面产生自由基引发St聚合,另一方面MMT发生了剥离分散;由此法制备的PS/MMT纳米复合材料,MMT片层无规、均匀地分散于PS基体中,片层厚度在几个纳米至十几个纳米之间,长度为几十至几百个纳米不等;大量的PS链段以化学键接枝在MMT的片层上,接枝在MMT片层上的PS的分子量及其分布与游离的PS不同.     

尼龙6/石墨纳米导电复合材料的制备与性能

通过原位插层聚合制备了尼龙 6 /石墨纳米导电复合材料 ,其室温导电渗滤阈值为 =0 75vol% ,远远低于常规导电粒子填充的聚合物复合材料 .当石墨体积分数为 2 0vol%时 ,室温电导率可达 10 -4 S/cm .透射电镜研究表明 :由于石墨经高温膨胀后其片层被剥离导致了片状石墨粒子具有巨大的径厚比 ,经原位插层聚合其片层厚度进一步被剥离为几十个纳米 ,同时原位插层聚合使得石墨粒子能够均匀分散在尼龙 6基体中 ,因而导致了该导电复合材料的低渗滤阈值和高导电性能 .     

原位聚合法制备超疏水的聚乙烯纳米复合材料

采用一种新方法将Ziegler-Natta催化剂组分TiCl4和MgCl2负载到蒙脱土(MMT)的层间,制备了TiCl4/MgCl2/MMT插层型催化剂.利用Ziegler-Natta催化剂特有的"形态复制效应",通过乙烯原位聚合制备出了表面具有花瓣状形态的聚乙烯纳米复合材料.这种聚乙烯纳米复合材料的表面与水的接触角达到(152.2±0.8)°,呈现超疏水性质.     

乳液聚合法制备剥离型PS/MMT纳米复合材料

以阳离子表面活性剂十八烷基三甲基氯化铵(OTAC)和烯丙基十八烷基二甲基氯化铵(ATAC)为插层处理剂改性蒙脱土(MMT),原位乳液聚合分别制备了PS/C18MMT和PS/AC18MMT两种纳米复合材料.XRD和TEM分析表明,MMT均被剥离成单个或几个片层无规的分散在PS基体中,TGA分析表明,MMT的加入提高了材料的耐热性能,当PS基体与有机化处理的MMT片层发生一定的化学连接后,PS/AC18MMT纳米复合材料表现出更好的耐热性能.动态力学分析表明,MMT的加入提高了PS的玻璃态储能模量,降低了材料的动态损耗;PS/AC18MMT纳米复合材料的玻璃化温度较PS有所提高,而PS/C18MMT的玻璃化温度与PS相比略有降低.     

双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

尼龙6/蒙脱土纳米复合材料的等温结晶动力学研究

用ＤＳＣ法研究了熔体插层制备的尼龙６／蒙脱土纳米复合材料的等温结晶行为．结果表明,加入少量的蒙脱土可明显提高尼龙６的结晶速率,降低球晶径向生长的单位面积表面自由能．从Ａｖｒａｍｉ方程和Ｈｏｆｍａｎ理论出发,得出蒙脱土纳米粒子的存在可明显改变尼龙６的结晶行为     

聚丙烯/凹凸棒土纳米复合材料结晶形态和形貌研究

采用熔融共混的方法 ,制备聚丙烯 凹凸棒土纳米复合材料 .通过X射线衍射 (XRD)分析凹凸棒土在聚丙烯复合材料中晶面间距的变化以及对聚丙烯晶型的影响 ,结果表明凹凸棒土在复合材料中晶面间距没有变化 ;聚丙烯晶型没有发生变化但晶粒尺寸增加了 .用示差扫描量热法 (DSC)分析聚丙烯复合材料的结晶度的变化 ,发现凹凸棒土的加入使复合材料的结晶温度提高 ,结晶速率增大 ,结晶度增加 .用偏光显微镜(POM)观察凹凸棒土对聚丙烯球晶的影响 ,结果表明凹凸棒土的加入起到了成核剂的作用 ,使得聚丙烯球晶尺寸减小 ,当凹凸棒土的加入量到 10 %左右时 ,观察不到完整的球晶 .利用扫描电子显微镜 (SEM)和原子力显微镜 (AFM)观察凹凸棒土在聚丙烯中的分散 ,发现凹凸棒土在聚丙烯基体中分散比较均匀 ,但呈无序分布 .     

聚醚醚酮球晶结构的形态特征研究

本文借助热台偏光显微镜,扫描电子显微镜,红外光谱等技术研究了聚醚醚酮(PEEK)球晶结构的形态特征。发现PEEK的同-球晶可在不同条件下呈现放射状及带状的形态,而这两种形态可相互进行可逆的热转变。对这两种球晶的相互转变规律及球晶的微观结构作了分析,提出了PEEK球晶结构的模型。     

Efficacy of clay content and microstructure of curing agents on the structure–property relationship of new‐generation polyurethane nanocomposites

The physicomechanical properties of new polyurethanes (PUs) derived from toluene diisocyanate, poly(propylene glycol), and cured by third‐generation hyperbranched polyester polyol (HB3), trimethylolpropane (TMP), or glycerol and their nanocomposites have been investigated. An apparent microphase‐segregated morphology of PU nanocomposites cured by HB3 has been observed by transmission electron microscopy and atomic force microscopy. Morphological studies reveal regions of mostly exfoliated and some intercalated morphology in the case of the nanocomposites, which have been further ascertained by X‐ray diffraction analysis. The HB3‐cured PU nanocomposite containing 8 wt% of modified montmorillonite (Cloisite 30B) clay shows approximately 140% increase in tensile strength along with improvement in thermal and dynamic mechanical properties in comparison with the control hyperbranched PU. It has also been found from Fourier transform infrared spectroscopy analysis that the extent of tethering reactions between the polymer chains carrying residual –NCO groups and the reactive hydroxyl (?OH) groups of HB3 is significant, and the nanofiller has been found to preferentially react with the –NCO group of the prepolymer. Furthermore, the properties of HB3‐cured PU have been compared with the glycerol and TMP‐cured PUs and their nanocomposites. The physicomechanical and thermal properties for nanocomposites of HB3‐cured PUs are superior to those of the conventionally cured PUs. Copyright © 2011 John Wiley & Sons, Ltd.     

聚对苯甲酰胺液晶态球晶生长机理

本文用热台偏光显微镜和透射电子显微镜研究了聚对苯甲酰胺(PBA)/H_2SO_4液晶态生长球晶的形态结构和结晶机理。结果表明,PBA/H_2SO_4向列型液晶相具有过冷状态,可达30—40℃左右,并可生长球晶结构,一般直径可达5毫米左右。20Wt％溶液在不同的过冷态结晶时,可以生成三种形态的球晶结构,这是由于构成球晶的基本结构单元——有序微区结构在不同过冷条件下堆砌排列的规整程度不同的缘故。球晶的形态结构只与过冷程度有关,而与溶液的浓度无关。同时还研究了变温和剪切应力下结晶的球晶形态。     

Polypropylene/montmorillonite nanocomposites toughened with SEBS‐g‐MA: Structure–property relationship

Polypropylene (PP)/organo‐montmorillonite (Org‐MMT) nanocomposites toughened with maleated styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) were prepared via melt compounding. The structure, mechanical properties, and dynamic mechanical properties of PP/SEBS‐g‐MA blends and their nanocomposites were investigated by X‐ray diffraction (XRD), polarizing optical microscopy (POM), tensile, and impact tests. XRD traces showed that Org‐MMT promoted the formation of β‐phase PP. The degree of crystallinity of PP/SEBS‐g‐MA blends and their nanocomposites were determined from the wide angle X‐ray diffraction via profile fitting method. POM experiments revealed that Org‐MMT particles served as nucleating sites, resulting in a decrease of the spherulite size. The essential work of fracture approach was used to evaluate the tensile fracture toughness of the nanocomposites toughened with elastomer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3112–3126, 2005     

Production of stable aqueous dispersion of poly(3,4-ethylenedioxythiophene) nanorods using graphene oxide as a stabilizing agent and their application for nitrite detection

A stable aqueous dispersion of poly(3,4-ethylenedioxythiophene) (PEDOT) nanorods stabilized by graphene oxide (GO) has been successfully prepared via interface polymerization of EDOT in the presence of GO for the first time. The non-covalent functionalization of PEDOT by GO leads to a PEDOT-GO dispersion that can be stable for several days without the observation of any floating or precipitated particles. Several analytical techniques including Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) have been used to characterize the resultant PEDOT-GO nanocomposites. It is found that such PEDOT-GO nanocomposites exhibit good catalytic activity toward the oxidation of nitrite, leading to a sensor for detection of nitrite. The linear detection range and detection limit are estimated to be 4 μM to 2.48 mM (r = 0.999), and 1.2 μM at a signal-to-noise ratio of 3, respectively.     

Morphology and crystallization of blends of linear low density polyethylene with a semiflexible liquid crystalline polymer

The morphology and the crystallization behavior of blends of linear low density polyethylene (LLDPE) with an experimental sample of a semiflexible liquid crystalline polymer (SBH 112 by Eniricerche, Italy) have been studied by differential scanning calorimetry (DSC), polarized optical microscopy (POM) and scanning electron microscopy (SEM). The blends possess a two-phase morphology, due to immiscibility of the two components. SEM observations show that dispersion of the minor SBH phase is favored at low (相似文献   

Preparation of poly(propylene)/clay layered nanocomposites by melt intercalation from pristine montmorillonite (MMT)

Poly(propylene)/clay nanocomposites were prepared by melt intercalation, using pristine montmorillonite (MMT), hexadecyl trimethyl ammonium bromide (C16), poly(propylene) (PP) and maleic acid (MA) modified PP (MAPP), The nanocomposites structure is demonstrated using X‐ray diffraction (XRD) and high resolution electronic microscopy (HREM). Our purpose is to provide a general concept for manufacturing polymer nanocomposites by melt intercalation starting from the pristine MMT. We found different kneaders (twin‐screw extruder or twin‐roll mill) have influence on the morphology of the PP/clay nanocomposites. Thermogravimetric analysis (TGA) shows that the thermal stability of PP/clay nanocomposites has been improved compared with that of pure PP. Copyright © 2003 John Wiley & Sons, Ltd.     

Thermal stability, crystallization, structure and morphology of syndiotactic 1,2-polybutadiene/organoclay nanocomposite

Syndiotactic 1,2-polybutadiene/organoclay nanocomposites were prepared and characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), polarized optical microscopy (POM), and differential scanning calorimetry (DSC), respectively. The XRD shows that exfoliated nanocomposites are formed dominantly at lower clay concentrations (less than 2%), at higher clay contents intercalated nanocomposites dominate. At the same time, the XRD indicates that the crystal structures of sPB formed in the sPB/organoclay nanocomposites do not vary, only the relative intensity of the peaks corresponding to (0 1 0) and (2 0 0)/(1 1 0) crystal planes, respectively, varies. The DSC and POM indicate that organoclay layers can improve cooling crystallization temperature, crystallization rate and reducing the spherulite sizes of sPB. TGA shows that under argon flow the nanocomposites exhibit slight decrease of thermal stability, while under oxygen flow the resistance of oxidation and thermal stability of sPB/organoclay nanocomposites were significantly improved relative to pristine sPB. The primary and secondary crystallization for pristine sPB and sPB/organoclay (2%) nanocomposites were analyzed and compared based on different approaches. The nanocomposites exhibit smaller Avrami exponent and larger crystallization rate constant, with respect to pristine sPB. Primary crystallization under isothermal conditions displays both athermal nucleation and three-dimensional spherulite growth and under nonisothermal processes the mechanism of primary crystallization becomes very complex. Secondary crystallization shows a lower-dimensional crystal growth geometry for both isothermal and nonisothermal conditions. The activation energy of crystallization of sPB and sPB/organoclay nanocomposites under isothermal and nonisothermal conditions were also calculated based on different approaches.