BiFeO_3空间选择性光化学还原Ag及光催化活性

采用溶胶-凝胶法和光还原沉积法制备出Ag改性的纳米BiFeO3粒子,对复合材料进行了FESEM、XRD、XPS、FTIR、UVVis/DRS等分析和表征。考察了波长365 nm以上的光照下,铁磁性材料的空间选择性光化学反应对复合材料的结构、形貌以及光谱性质的影响。以罗丹明B为模拟污染物,考察了纳米Ag-BiFeO3粒子的可见光光催化活性以及稳定性。结果表明:通过光化学沉积,不仅增强了BiFeO3在200~800 nm光照下的响应,而且抑制了光腐蚀现象,提高了BiFeO3的稳定性。在波长大于400nm的光照射12 h后单纯纳米BiFeO3粒子对罗丹明B脱色率约为74%,而Ag-BiFeO3复合材料6 h后约为90%,并且重复使用3次后光催化效果基本不变。     

溶剂热法制备BiFeO3基纳米颗粒光催化剂及其性能

以聚酰胺-胺（PAMAM）树形分子为稳定剂,采用溶剂热法制得了纯相BiFeO₃纳米颗粒（A）和BiFeO₃/Bi₂₅FeO40/Fe₂O₃复合纳米颗粒（B）,并采用HRTEM、XRD、UV-Vis、SQUID对其结构和性能进行了表征。2种颗粒结晶良好,粒径小于10 nm,能有效光催化降解亚甲基蓝,磁性回收率分别为74.6%（A）和90.2%（B）。BiFeO₃/Bi₂₅FeO40/Fe₂O₃复合纳米颗粒的光催化与磁性能均优于纯相BiFeO₃纳米颗粒,是因为复合纳米颗粒含有多种相,相界面存在异质结构有利于光生载流子的分离和迁移,并且对可见光的吸收能力更强。     

不同水热条件下TiO2/电气石复合材料的光催化机制

为了解决TiO₂纳米光催化剂易团聚、禁带宽度大的缺点,本文采用水热法制备了TiO₂/电气石（3%）复合材料,研究了水热时间（2~10 h）和水热温度（120~200℃）对TiO₂/电气石（3%）的光催化性能的影响。发现光催化降解罗丹明B的降解率由单独TiO₂的60%提高到加入电气石后的99.4%。电气石具备自发极化电场效应,降低了TiO₂的禁带宽度和光生电子和空穴的复合率。在水热温度160℃、水热时间4 h条件下制备的TiO₂/电气石（3%）表现出最高的光催化降解罗丹明B的性能。说明TiO₂与这种有自发极化的材料复合能够有效提高其光催化性能。     

Ag3PO4/Ni薄膜的制备及其光催化降解罗丹明B的性能和机理

用电化学方法制备Ag₃PO₄/Ni薄膜,以扫描电子显微镜(SEM)、X射线衍射(XRD)和紫外-可见漫反射光谱(UV-Vis DRS)对薄膜的表面形貌、晶相结构、光谱特性及能带结构进行了表征,以罗丹明B为模拟污染物对薄膜的光催化活性和稳定性进行了测定,采用向溶液中加入活性物种捕获剂的方法对薄膜光催化降解机理进行了探索.结果表明:最佳工艺下制备的Ag₃PO₄/Ni薄膜具有致密的层状表面结构,是由多晶纳米颗粒构成的薄膜.薄膜具有较高的光催化活性和突出的光催化稳定性,可见光下催化作用60 min,薄膜光催化罗丹明B的降解率是多孔P25 TiO₂/ITO纳米薄膜(自制)的2.3倍;在保持薄膜光催化活性基本不变的前提下可循环使用6次.给出了可见光下薄膜光催化降解罗丹明B的反应机理.     

锐钛矿型多孔TiO2薄膜的溶解法制备及性能表征

在具有锐钛矿晶粒的TiO₂溶胶中加入苯丙乳液粒子，使用该混合液浸渍提拉涂膜，然后利用甲苯将薄膜中的苯丙乳液粒子溶解去除，并通过重复涂膜，在室温下获得了具有良好多孔性的锐钛矿型TiO₂薄膜。考察了多孔薄膜的表面形貌、光学性能、吸附性能和光催化性能。结果表明：随薄膜涂膜次数的增加，TiO₂多孔薄膜的吸光度增大，透光率减小，光吸收边波长向长波方向移动。罗丹明B在TiO₂多孔薄膜上的吸附量随涂膜次数的增加先升高，后降低；多次涂膜会在薄膜中产生半封闭的孔洞，经过长时间的毛细渗透等作用能进一步增加薄膜对罗丹明B的吸附。TiO₂多孔薄膜通过吸附+光催化氧化的模式快速分解罗丹明B，其活性主要受到薄膜在光催化反应初期的吸附能力的影响。此外，TiO₂的负载量、光的利用效率、以及光生电荷迁移及其分离等也是影响薄膜光催化活性的因素。     

纳米Ag@AgBr表面敏化K2Ti4O9可见光催化剂的微波合成、表征和光催化活性

利用微波法合成纳米尺寸Ag@AgBr表面敏化K₂Ti₄O₉的复合光催化剂（Ag@AgBr/K₂Ti₄O₉）,并通过SEM、X-射线能量色散谱（EDX）、TEM、选定区域电子衍射（SAED）、XRD、紫外-可见漫反射（UV-Vis Diffuse Reflectance）、XPS等对其进行了表征,同时在可见光下测定催化剂对有机物降解的光催化活性。结果表明,粒径为0.2~0.5μm的Ag@AgBr均匀分散在K₂Ti₄O₉表面,Ag@AgBr/K₂Ti₄O₉对可见光有很好的吸收且Ag@AgBr的担载量影响可见光的吸收。当Ag@AgBr的担载量为25wt%时,复合光催化剂具有最高的光催化活性,光照1h对罗丹明B（RhB）的降解率可达97%。另外,催化剂的担载量和稳定性也做了考察。催化剂较高的光催化活性主要归因于Ag纳米粒子的表面等离子体效应和有效的光生电子-空穴的分离。     

等离子体修饰磁载TiO2光催化剂性能研究

以化学共沉法制备的CoFe₂O₄纳米粒子为磁核,采用TiCl₄水解包覆技术制备磁载二氧化钛纳米复合粒子CoFe₂O₄ /TiO_x(TCF),利用低温等离子体技术修饰TCF制备了CoFe₂O₄/TiO₂(PTCF)纳米复合光催化剂。运用VSM(振动样品磁强计)技术对样品磁性能进行研究,结果表明：等离子体修饰后的复合材料仍具有较高的饱和磁化强度,可在外加磁场作用下实现催化剂在水中的分离与回收;样品的XRD、TEM和UV-Vis分析测试结果表明：等离子体修饰后的复合材料有锐钛矿型TiO₂存在;TEM谱图显示磁核CoFe₂O₄的平均粒径约为20 nm,TCF复合粒子的粒径约为30~40 nm,TiO₂包覆层的厚度为10~20 nm。与纯TiO₂相比PTCF样品对光的吸收拓展到整个紫外-可见区,扩大了光谱响应范围;对甲基橙溶液降解的光催化活性评价研究表明：TCF复合粒子等离子体修饰后的PTCF纳米复合光催剂的光催化活性明显提高。     

Bi6Fe1.9Co0.1Ti3O18纳米片负载Au尺寸对其可见光光催化性能的影响

我们通过一种简单的化学方法制备了具有可见光催化性能的Bi₆Fe_1.9Co_0.1Ti₃O₁₈/Au（BFCTO/Au）纳米复合材料。结果表明,通过负载不同颗粒大小的Au纳米颗粒（~23 nm、~36 nm、~55 nm和~80 nm）,BFCTO的可见光光催化性能明显增强,其中负载粒径为~23 nm的Au纳米颗粒的BFCTO/Au-1样品的可见光光催化效率最高。     

BiOI负载MIL-101(Fe)@BiOI衍生BiFeO3@Fe2O3的增强光催化性能

采用溶剂热法合成了MIL-101(Fe)@BiOI复合材料,然后将其煅烧制备光催化性能增强的BiFeO₃@Fe₂O₃@BiOI三元复合材料。采用X射线衍射、扫描电镜、紫外可见漫反射吸收光谱等测试手段表征复合材料的组成、结构、形貌。将复合材料用于可见光照射下光催化降解四环素,研究复合比例(质量比)、pH和浓度对光催化性能的影响。电化学阻抗谱、光电流响应和莫特-肖特基曲线测试分析表明三元复合材料 BiFeO₃@Fe₂O₃@BiOI 表现出更强的光电流响应和更低的电荷转移电阻。当BiFeO₃、Fe₂O₃和BiOI三者理论质量比为1:1:1时,中性条件下降解活性最高,四环素去除率为81%。     

静电纺丝制备g-C3N4/C纳米纤维及其可见光降解性能

采用g-C₃N₄纳米片与聚丙烯腈进行静电复合纺丝,再经预氧化和碳化制得g-C₃N₄/C纳米纤维。利用傅立叶变换红外光谱仪（FTIR）、X射线衍射仪（XRD）、拉曼光谱（Raman）和扫描电子显微镜（SEM）对样品结构和形貌进行表征,通过紫外-可见漫反射光谱（UV-Vis DRS）分析可见光响应性。研究表明,复合纳米纤维对罗丹明B表现出较好的可见光降解活性,源于无定形相/石墨相混合结构的碳基体能够降低g-C₃N₄的光生电子-空穴对复合的几率。复合纳米纤维膜在光催化降解搅拌条件下始终能保持完整,经过多次回收和光催化实验,对罗丹明B的光降解率依然较高,表现出较优异的循环利用稳定性。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Crystal growth, structure determination, and optical properties of new potassium-rare-earth silicates K3RESi2O7 (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu)

Single crystals of K₃RESi₂O₇ (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) were grown from a potassium fluoride flux. Two different structure types were found for this series. Silicates containing the larger rare earths, RE=Gd, Tb, Dy, Ho, Er, Tm, Yb crystallize in a structure K₃RESi₂O₇ that contains the rare-earth cation in both a slightly distorted octahedral and an ideal trigonal prismatic coordination environment, while in K₃LuSi₂O₇, containing the smallest of the rare earths, lutetium is found solely in an octahedral coordination environment. The structure of K₃LuSi₂O₇ crystallizes in space group P6₃/mmc with a=5.71160(10) Å and c=13.8883(6) Å. The structures containing the remaining rare earths crystallize in the space group P6₃/mcm with the lattice parameters of a=9.9359(2) Å, c=14.4295(4) Å, (K₃GdSi₂O₇); a=9.88730(10) Å, c=14.3856(3) Å, (K₃TbSi₂O₇); a=9.8673(2) Å, c=14.3572(4) Å, (K₃DySi₂O₇); a=9.8408(3) Å, c=14.3206(6) Å, (K₃HoSi₂O₇); a=9.82120(10) Å, c=14.2986(2) Å, (K₃ErSi₂O₇); a=9.80200(10) Å, c=14.2863(4) Å, (K₃TmSi₂O₇); a=9.78190(10) Å, c=14.2401(3) Å, (K₃YbSi₂O₇). The optical properties of the silicates were investigated and K₃TbSi₂O₇ was found to fluoresce in the visible.     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Structural studies of five layer Aurivillius oxides: A2Bi4Ti5O18 (A=Ca, Sr, Ba and Pb)

The room temperature structures of the five layer Aurivillius phases A₂Bi₄Ti₅O₁₈ (A=Ca, Sr, Ba and Pb) have been refined from powder neutron diffraction data using the Rietveld method. The structures consist of [Bi₂O₂]²⁺ layers interleaved with perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks. The structures were refined in the orthorhombic space group B2eb (SG. No. 41), Z=4, and the unit cell parameters of the oxides are a=5.4251(2), b=5.4034(1), c=48.486(1); a=5.4650(2), b=5.4625(3), c=48.852(1); a=5.4988(3), b=5.4980(4), c=50.352(1); a=5.4701(2), b=5.4577(2), c=49.643(1) for A=Ca, Sr, Ba and Pb, respectively. The structural features of the compounds were found similar to n=2-4 layers bismuth oxides. The strain caused by mismatch of cell parameter requirements for the [Bi₂O₂]²⁺ layers and perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks were relieved by tilting of the TiO₆ octahedra. Variable temperature synchrotron X-ray studies for Ca and Pb compounds showed that the orthorhombic structure persisted up to 675 and 475 K, respectively. Raman spectra of the compounds are also presented.     

Metal-organic deposition of YBa2Cu3Ox and Bi2Sr2Ca1Cu2Ox films on various substrates starting from different fluorine-free metallorganic compounds

YBa₂Cu₃O_x (Y-123) and Bi₂Sr₂Ca₁Cu₂O_x (Bi-2212) films on various substrates have been prepared by Metal-Organic Deposition starting from different metallorganic fluorine-free compounds and using a very simple instrumentation. The processing conditions include a rapid pyrolysis step in air and an annealing step in oxygen for Y-123 and in air for Bi-2212. The films obtained have been characterized by X-ray diffraction (XRD) and the formation of a superconducting phase of Y-123 or Bi-2212 was confirmed measuring the critical temperature (T _c) with Ac-susceptibility and resistive measurements. Microstructure and final cationic ratios have been studied by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).     

Decomposition of P2S2N4(Si(CH3)3)4A12C14 as Studied by FT-Raman and Quantum Chemistry Means

The dimeric title compound decomposes upon heating to give the monomer and desulphurized monomer as shown by FT-Raman and quantum chemical means.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

The crystal chemistry of Bi6TP2O15+x, T=Fe, Ni, Zn: Isomorphism and polymorphism, structural relationship to Bi6TiP2O16

The crystal structures of compounds with nominal compositions Bi₆FeP₂O_15+x (I), Bi₆NiP₂O_15+x (II) and Bi₆ZnP₂O_15+x (III) were determined from single-crystal X-ray diffraction data. They are monoclinic, space group I2, Z=2. The lattice parameters for (I) are a=11.2644(7), b=5.4380(3), c=11.1440(5) Å, β=96.154(4)°; for (II) a=11.259(7), b=5.461(4), c=11.109(7) Å, β=96.65(1)°; for (III) a=19.7271(5), b=5.4376(2), c=16.9730(6) Å, β=131.932(1)°. Least squares refinements on F² converged for (I) to R1=0.0554, wR₂=0.1408; for (II) R₁=0.0647, wR₂=0.1697; for (III) R₁=0.0385, wR₂=0.1023. The crystals are complexly twinned by 2-fold rotation about , by inversion and by mirror reflection. The structures consist of edge-sharing articulations of OBi₄ tetrahedra forming layers in the a-c plane that then continue by edge-sharing parallel to the b-axis. The three-dimensional networks are bridged by Fe and Ni octahedra in (I) and (II) and by Zn trigonal bipyramids in (III) as well as by oxygen atoms of the PO₄ moieties. Bi also randomly occupies the octahedral sites. Oxygen vacancies exist in the structures of the three compounds due to required charge balances and they occur in the octahedral coordination polyhedron of the transition metal. In compound (III), no positional disorder in atomic sites is present. The Bi-O coordination polyhedra are trigonal prisms with one, two or three faces capped. Magnetic susceptibility data for compound (I) were obtained between 4.2 and 350 K. Between 4.2 and 250 K it is paramagnetic, μ_eff=6.1 μ_B; a magnetic transition occurs above 250 K.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.