纳米二氧化硅影响人肺癌细胞的定量糖蛋白质组学研究

纳米二氧化硅(纳米SiO₂)是一种正在规模化生产的纳米材料, 无定型纳米SiO₂因其吸入和口服对生命体不会造成直接的危害被认为是生物安全的纳米材料, 已被广泛用于疾病诊断、生物分析和成像、药物载体等的研究中, 导致其进入人体的方式日益增多, 因此它对人体健康影响的研究对于其作为生物材料真正实现广泛应用尤为重要. 本文采用肼化学方法为基础的定量蛋白质组学对无定型纳米SiO₂进入人肺癌细胞后产生的影响进行了分析, 结果表明其进入细胞后, 导致细胞内的平衡状态发生变化, 从而影响了细胞内许多重要的蛋白质的表达水平. 部分跨膜蛋白质表达的变化对纳米SiO₂进入细胞的途径的阐明有一定的指导意义.     

金属助剂对Ni/SiO2催化剂苯甲醚加氢脱氧性能的影响

采用等体积浸渍法制备了Ni/SiO₂及Ni与金属助剂M（M=Fe、Co、Cu、Zn及Ga）物质的量比为30的Ni基双金属催化剂（记作Ni₃₀M/SiO₂）,利用H₂-TPR、XRD、H₂化学吸附、NH₃-TPD以及N₂物理吸附-脱附等手段对催化剂进行了结构表征,研究了不同助剂对催化剂结构与苯甲醚加氢脱氧性能影响。结果发现,金属助剂影响了催化剂前驱体中镍物种的还原性能,表明金属助剂及镍之间存在一定相互作用。Ni₃₀M/SiO₂中Ni-M双金属晶粒粒径和Ni/SiO₂中金属Ni晶粒粒径相近。由于表面张力较低的金属会在双金属晶粒表面富集,Ni₃₀M/SiO₂的H₂化学吸附量不同程度地低于Ni/SiO₂。另外,Ni₃₀M/SiO₂催化剂的酸量（尤其较弱酸中心酸量）高于Ni/SiO₂。在300℃、常压、苯甲醚质量空速1.0 h^-1及H₂与苯甲醚物质的量比为25：1条件下考察了各催化剂苯甲醚的加氢脱氧性能。Ni₃₀M/SiO₂上苯甲醚转化率不同程度低于Ni/SiO₂,原因在于Ni₃₀M/SiO₂催化剂H₂化学吸附量较低。Ga及Zn改性催化剂上三苯（包括苯、甲苯及二甲苯）选择性分别为81.7%和76.8%,高于Ni/SiO₂（71.5%）,且Ni₃₀Ga/SiO₂及Ni₃₀Zn/SiO₂上三苯收率（分别为65.0%及63.8%）高于或接近于Ni/SiO₂（63.7%）。Ni/SiO₂及Ni₃₀M/SiO₂催化剂中,Ni₃₀Zn/SiO₂具有较高甲基转移能力及较低C-C键氢解活性。从提高碳收率、降低耗氢量角度而言,Ni₃₀Zn/SiO₂具有较佳的加氢脱氧性能,与Ni和Zn之间作用及Zn亲氧性高于Ni有关。     

类蛋结构的可磁分离光催化剂纳米球的制备及催化性能

通过反胶束和静电自组装方法制备了一种类蛋结构的可磁分离光催化剂纳米材料SiO₂@NiFe₂O₄@TiO₂(TSN), 这种光催化剂对甲基橙废水有较好的降解效果, 并显示出了超顺磁性, 通过外加磁场方便地实现催化剂在水中的分离与回收. 该光催化剂纳米球的X射线衍射, TEM和FTIR结果表明, 铁酸镍纳米粒子被包裹在SiO₂内, 形成SiO₂@NiFe₂O₄(SN)纳米球载体, 纳米TiO₂颗粒组装在SN表面, 形成TiO₂光催化壳层. 利用甲基橙的降解考察了光催化剂纳米球的活性, 结果表明, 在NiFe₂O₄和TiO₂之间包覆一层无定形的SiO₂可以显著提高光催化剂纳米球TSN的催化活性.     

全无机钙钛矿量子点的疏水改性及LED应用——推荐一个本科生综合化学实验

介绍一个综合化学实验——全无机钙钛矿量子点的疏水改性及LED应用。我们以三甲基氯硅烷和莫来石纤维增强SiO₂气凝胶的疏水性和韧性，获得疏水SiO₂气凝胶，随后以该疏水SiO₂气凝胶吸附全无机钙钛矿量子点形成CsPbX3@SiO₂气凝胶复合材料。通过接触角、红外光谱、X射线衍射等表征手段证实SiO₂气凝胶的成功改性，并制作了LED器件。本实验涉及材料的合成、表征和应用，可作为化学和应用化学专业学生的综合化学实验，有助于提高学生的科学素养，激发对科学研究的兴趣。     

硅酸钠法合成高比表面多孔二氧化硅

以硅酸钠和盐酸为原料,用化学沉淀法制备高比表面多孔SiO₂,并对其性能进行了研究.结果表明,所合成的SiO₂比表面积可达1300m₂/g以上,具有蜂窝状的微孔,孔径均匀,而且性能稳定.     

聚合物/SiO2杂化材料在药物控制释放中的应用*

聚合物用作药物控制释放载体时,具有释药浓度可控、药物的生物利用率高、可实现靶向治疗等优点。但有些聚合物也存在机械强度低、化学稳定性差、生物相容性不理想等缺点。二氧化硅(SiO₂)具有多孔、无毒、生物相容性好、化学和机械稳定性高、表面易功能化等优点。但SiO₂用作药物控制释放载体时,有时也存在载药量低、不能装载大分子药物、不能实现靶向释放等缺点。聚合物/SiO₂杂化材料作为药物控制释放载体,可有效结合二者的优点,并克服二者的缺陷。根据聚合物的种类和杂化体系性质的不同,我们分别对温敏性聚合物/SiO₂杂化材料、聚电解质/SiO₂杂化材料、生物高分子/SiO₂杂化材料以及其它一些聚合物/SiO₂杂化材料体系在药物控制释放中的应用进行了介绍,并展望了该领域今后的研究发展方向。     

硅源对蒸氨法制备Cu/SiO2催化剂催化甲醇裂解制氢的影响

采用蒸氨法制备Cu/SiO₂催化剂,分别考察气相二氧化硅（SiO₂-aer）、硅胶（SiO₂-gel）和碱性硅溶胶（SiO₂-sol）对Cu/SiO₂催化剂催化甲醇裂解制氢性能的影响,并采用N₂吸附-脱附、N₂O化学吸附、电感耦合等离子体原子发射光谱法（ICP-AES）、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、透射电子显微镜（TEM）和X射线光电子能谱（XPS）等方法对催化剂进行表征。结果表明,硅源对Cu/SiO₂催化剂的活性具有较大影响。以碱性硅溶胶作为硅源制得的Cu/SiO₂-sol催化剂比表面积较大,活性中心粒径较小且分散均匀,这些使得其制氢性能优于其他两种硅源为载体所制备的催化剂。在反应温度280 ℃,反应压力1 MPa,甲醇质量空速0.6 h^-1的条件下,相较于Cu/SiO₂-aer和Cu/SiO₂-gel催化剂,Cu/SiO₂-sol催化剂的甲醇转化率分别提高10％和7％,气相副产物CH₄和CO₂浓度也有所降低,该催化剂上的甲醇转化率和气体收率分别达到98.4%和96.7%。     

负载型铂催化剂中的载体效应

本文用程序升温热脱附法和氢氧滴定法研究了SiO₂、SiO₂·Al₂O₃、Al₂O₃、SiO₂·SnO₂和Al₂O₃·SnO₂等和Pt的相互作用,表明Pt和载体作用强弱的顺序为:Al₂O₃>SiO₂·Al₂O₃>SiO₂;发现SnO₂具有强化SiO₂和Al₂O₃载体效应的作用;提出Pt和载体相互作用较强部位可能是Pt和缺氧氧化物所形成的表面络合物--Pt-[Al₂O_x]和Pt-[SnO_x]。     

溶胶-凝胶法构筑介孔二氧化硅纳微结构

基于硅酸脂水解/缩合的溶胶-凝胶法是目前制备SiO₂胶体最为常用的化学方法. 在溶胶-凝胶反应过程中, 引入介孔导向剂(通常是表面活性剂)可以得到具有介孔结构的SiO₂胶体. 通过对硅酸脂在多相体系界面水解/缩合过程的调控, 可以构筑具有不同纳微结构的介孔SiO₂材料, 为拓展介孔SiO₂材料的应用领域提供了新机遇, 同时也丰富了对溶胶-凝胶法的理解和认识. 本文综述了利用溶胶-凝胶法构筑介孔SiO₂纳微结构的最新研究进展, 并介绍了其在生物医药、 催化、 吸附分离等领域的应用前景, 最后对这一领域所面临的问题和未来发展方向进行了总结和展望.     

H2S/H2硫化温度对MoP/SiO2催化剂硫醚化性能的影响

以负载磷酸钼为前驱体,采用程序升温还原法制备了MoP/SiO₂催化剂,以体积分数3%H₂S/H₂对其进行了硫化处理,利用XRD、CO化学吸附、NH₃-TPD、HRTEM-EDX、ICP-AES以及XPS等手段对催化剂进行了表征,研究了硫化温度对MoP/SiO₂催化剂结构和异戊二烯与正丁硫醇硫醚化性能的影响。结果表明,即使在400℃硫化处理也未改变MoP/SiO₂催化剂中MoP体相结构;随着硫化温度提高,催化剂表面酸量增加、金属位数量减少,降低了催化剂C-S键氢解及异戊二烯深度加氢活性,但同时也提高了催化剂烯烃聚合活性。经120℃硫化处理的MoP/SiO₂兼具较佳硫醚化及异戊二烯选择加氢性能。     

Preparation and application of poly(alkoxytitanate) as a TiO2 precursor with high storage stability

Titanium dioxide is a basic material of our daily life. Because of its favourable properties, such as harmlessness, chemical stability, photocatalytic activity, or whiteness it is increasingly applied in both micro and nano particles and thin films and coating. One of the available procedures for film forming is the sol–gel technology, an inexpensive low temperature process with wide possibilities to vary film properties by changing the composition of the precursor solution or other parameters. In the paper a new precursor polymer for TiO₂ film-preparation with high storage and processing stabilities is introduced and applied in thin film forming. The new precursor poly(alkoxytitanate) is prepared by a one step, water-free sol–gel method. A smooth TiO₂ film can be prepared using this precursor by spin-coating followed by H₂-plasma curing. Comparing to a common precursor such as Ti(O–iPr)₄, this precursor has a good solubility in different solvents and a much higher storage stability. The easy to modify precursor end groups enable the tailoring of properties regarding to hydrolysis to both TiO₂ particles and films.     

Effect of Tetraethoxysilane (hybrid sol) on chemical and abrasion resistance, and dyeability of nano polyamide mat

This work deals with the application of inorganic–organic sol–gel layer on polyamide nanofabrics to protect nanofibres against chemical and mechanical damages. To this aim, fabric specimens with different silica concentration (1, 5, 10, 20 and 40 %) have been prepared. Layers were deposited on polyamide nanofabrics by pad-dry-cure technique. Permeability was defined as the rate of airflow perpendicular to a test sample under specified conditions for the test area, pressure gradient, and time according to DIN EN ISO 9237. Abrasion resistance testing was performed for determining the weight loss of samples before and after sol–gel treatment. For chemical resistant measurement, Formic Acid was used. Infrared spectroscopy was also used for investigation of the chemical structure of the treated polyamide nano mats. The morphology of the fabrics was observed using a Scanning Electron Microscope. Also both untreated and sol–gel treated samples were dyed using cationic dyestuff and dyeability of polyamide nanomats after treating by hybrid sol were compared with untreated one. The results indicate that the K/S value of CI. Basic Red 46 are enhanced by increasing the concentration of Tetraethoxysilane based sol, respectively. Also by increasing the concentration of sol–gel to 50 %, the greatest resistance to formic acid was achieved.     

Sol–gel derived nano zinc oxide for the reduction of zinc oxide level in natural rubber compounds

Zinc oxide (ZnO) nanoparticles are synthesized by polymeric sol–gel method and characterized by X-ray diffraction, field-emission scanning electron microscopy. The cure characteristics, mechanical properties and thermal behaviour of natural rubber (NR) systems containing nano ZnO are investigated and compared to those of NR with micro-sized (conventional) ZnO. The NR vulcanizate with 0.5 phr (parts per hundred parts of rubber) sol–gel derived nano ZnO shows improvement in the curing and mechanical properties in comparison to the NR vulcanizate with 5 phr conventional ZnO. Thermogravimetric analysis reveals that nano ZnO impose better thermal stability than conventional ZnO in the NR vulcanizates. Thus, nano ZnO not only acts as a curing activator but also nano filler to improve the resulting properties of the NR vulcanizates. More essentially nano ZnO leads to the reduction of ZnO level in the NR compounds. Therefore, sol–gel derived nano ZnO diminishes the pollution of aquatic environment due to higher amount of conventional ZnO in rubber compounds.     

纳米溶胶-凝胶膜修饰电极及电化学催化性能

报道了以纳米硅溶胶-凝胶（sol-gel）膜为载体的化学修饰电极。用sol-gel法在金电极上固定亚甲蓝及硫堇，发现固定于纳米硅溶胶-凝胶膜内的亚甲蓝和硫堇均有良好的电化学活性，并对同时固定于膜内的NADH、血红蛋白等生物分子产生显著的催化氧化还原作用。     

Immobilized ruthenium complexes and aspects of their reactivity

Methodologies for the immobilization and characterization of ruthenium complexes into/onto functionalized silica gel, zeolites, polymers, dendrimers, sol–gel, nano and microparticles are described. The corresponding spectroscopic, electrochemical, and photochemical properties as well as chemical reactivities are used for their characterization and study. Comparison between the reactivities of immobilized and in solution species is presented. Some biological applications are also described.     

溶胶凝胶法制备纳米LiCoO2

纳米微粒;放电初容量;循环稳定性;溶胶凝胶法制备纳米LiCoO2     

纳米二氧化硅复合悬浮液合成及聚合物吸附研究

从水玻璃合成了纳米硅溶胶,并以它为起始原核,通过水解钛酸正丁酯沉积二氧化钛,制得了稳定的二氧化钛复合二氧化硅纳米悬浮液,研究了添加的高分子两亲分散剂聚醚多胺在硅胶粒上的吸附和二氧化钛沉积过程中的贡献。研究结果表明,添加的聚醚多胺吸附在硅胶粒表面,有利于硅溶胶的稳定;钛酸正丁酯-丁醇-硫酸水解反应是可逆的,二氧化钛向硅胶粒定向沉积,这些沉积物呈无定形态,在沉积过程中,吸附的这些添加剂发生离子化,其阳离子端基形成的离子氛有利于二氧化钛沉积,并能减少胶粒粘接或团聚。     

An H2O2 Biosensor Based on Immobilization of Horseradish Peroxidase Labeled Nano‐Au in Silica Sol‐Gel/Alginate Composite Film

Abstract

A novel approach to assemble an H₂O₂ amperometric biosensor was introduced. The biosensor was constructed by entrapping horseradish peroxidase (HRP) labeled nano‐scaled particulate gold (nano‐Au) (HRP‐nano‐Au electrostatic composite) in a new silica sol‐gel/alginate hybrid film using glassy carbon electrode as based electrode. This suggested strategy fully merged the merits of sol‐gel derived inorganic‐organic composite film and the nano‐Au intermediator. The silica sol‐gel/alginate hybrid material can improve the properties of conventional sol‐gel material and effectively prevent cracking of film. The entrapment of HRP in the form of HRP‐nano‐Au can not only factually prevent the leaking of enzyme out of the film but also provide a favorable microenvironment for HRP. With hydroquinone as an electron mediator, the proposed HRP electrode exhibited good catalytic activity for the reduction of H₂O₂. The parameters affecting both the qualities of sol‐gel/alginate hybrid film and the biosensor response were optimized. The biosensor exhibited high sensitivity of 0.40 Al mol^?1 cm^?2 for H₂O₂ over a wide linear range of concentration from 1.22×10^?5 to 1.46×10^?3 mol L^?1, rapid response of <5 s and a detection limit of 0.61×10^?6 mol L^?1. The enzyme electrode has remarkable stability and retained 86% of its initial activity after 45 days of storage in 0.1 mol L^?1 Tris‐HCl buffer solutions at pH 7.     

Sol–Gel‐Derived Biohybrid Materials Incorporating Long‐Chain DNA Aptamers

Sol–gel‐derived bio/inorganic hybrid materials have been examined for diverse applications, including biosensing, affinity chromatography and drug discovery. However, such materials have mostly been restricted to the interaction between entrapped biorecognition elements and small molecules, owing to the requirement for nanometer‐scale mesopores in the matrix to retain entrapped biorecognition elements. Herein, we report on a new class of macroporous bio/inorganic hybrids, engineered through a high‐throughput materials screening approach, that entrap micron‐sized concatemeric DNA aptamers. We demonstrate that the entrapment of these long‐chain DNA aptamers allows their retention within the macropores of the silica material, so that aptamers can interact with high molecular weight targets such as proteins. Our approach overcomes the major limitation of previous sol–gel‐derived biohybrid materials by enabling molecular recognition for targets beyond small molecules.     

Ferromagnetic Co-doped ZnO film and fine patterns prepared using photosensitive sol–gel method

Using zinc acetate and cobalt acetate as raw materials, isopropanol as solvent, and monoethanolamine as stabilizer, photosensitive Co-doped ZnO sol was prepared by chemical modification with benzoylacetone. Chelate rings of benzoylacetone with zinc ions are formed in the Co-doped ZnO sol and corresponding gel films. Irradiation of the gel film by a UV lamp in air leads to decomposition of the chelate ring. Selective irradiation followed by leaching and annealing gave rise to the formation of Co-doped ZnO fine patterns. The Co-doped ZnO film prepared using the photosensitive sol–gel method had a wurtzite structure and showed room-temperature ferromagnetic property.