喷涂法制备大面积倒置聚合物光伏器件

采用喷涂工艺制备了结构为ITO/ZnO/P3HT∶PCBM/V2O5/Ag(P3HT:聚噻吩;PCBM:6,6-苯基-C61-丁酸甲酯)的大面积倒置光伏器件,有效面积为1.0×1.1 cm2。 光谱测试结果表明,退火处理后,P3HT∶PCBM薄膜吸收显著增强,并且产生一定程度的红移。 采用ZnO和V2O5代替LiF和PEDOT∶PSS(聚(3,4-乙撑二氧噻吩)∶聚苯乙烯磺酸盐)作为器件修饰层,避免了PEDOT∶PSS对ITO的腐蚀和LiF潮解,采用Ag代替Al作为金属背电极避免了Al被氧化。 经过后退火处理器件的效率从1.1%提升至1.65%。 器件的稳定性相对于传统结构有了大幅提升,8周后器件效率只衰减10%。     

Dual length morphological model for bulk‐heterojunction,polymer‐based solar cells

We present a dual length morphological model for the active layer of bulk‐heterojunction, polymer‐based solar cells using results from neutron and X‐ray scattering techniques. Two critical characteristic lengths are found in the mixtures composed of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). A characteristic length at 15 nm is the local characteristic of the P3HT crystals and PCBM agglomerations, which is independent of the bulk composition upon relaxation by thermal annealing. Conversely, a larger bicontinuous structure described by Teubner–Strey model with phase distances between 23 and 35 nm forms only after thermal annealing, which is highly correlated to the bulk compositions. These results suggest phase separation between the polymer and fullerene can only be partially manipulated by simple processing techniques such as coating conditions and annealing, and a more rigorous design of the morphology should be implemented in the future. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 387–396     

Effects of amorphous poly(3‐hexylthiophene) on active‐layer structure and solar cells performance

A key challenge to the development of polymer‐based organic solar cells is the issue of long‐term stability, which is mainly caused by the unstable time‐dependent morphology of active layers. In this study, poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl C60‐butyric acid methyl ester (PCBM) blend is used as a model system to demonstrate that the long‐term stability of power conversion efficiency can be significantly improved by the addition of a small amount of amorphous regiorandom P3HT into semicrystalline regioregular one. The optical properties measured by UV–vis absorption and photoluminescence reveal that regiorandom P3HT can intimately mix with PCBM and prevent the segregation of PCBM. In addition, X‐ray scattering techniques were adopted to evidence the retardation of phase separation between P3HT and PCBM when regiorandom P3HT is added, which is further confirmed by optical microscopy that shows a reduction of large PCBM crystals after annealing at high temperature in the presence of regiorandom P3HT. The improvement of the long‐term stability is attributed to the capability of amorphous P3HT to be thermodynamically miscible with PCBM, which allows the active layer to form a more stable structure that evolves slower and hence decelerates the device decay. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 975–985     

Synthesis and photovoltaic properties of low‐bandgap 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole‐based poly(heteroarylenevinylene)s

Three novel low‐bandgap copolymers containing alkylated 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole (HBT) and different electron‐rich functional groups (dialkylfluorene (PFV‐HBT), dialkyloxyphenylene (PPV‐HBT) and dialkylthiophene (PTV‐HBT)) were prepared by Horner polycondensation reactions and characterized by ¹H NMR, gel permeation chromatography, and elemental analysis. The alkyl side chain brings these polymeric materials good solubility in common organic solvents, which is critical for the manufacture of solar cells in a cost‐effective manner. The copolymers exhibit low optical bandgap from 1.48 to 1.83 eV. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the copolymers were measured by cyclic voltammetry. Theoretical calculations revealed that the variation laws of HOMO and the LUMO energy levels are well consistent with cyclic voltammetry measurement. The bulk heterojunction photovoltaic devices with the structure of ITO/PEDOT‐PSS/polymer:PCBM/LiF/Al were fabricated by using the three copolymers as the donor and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as the acceptor in the active layer. The device based on PTV‐HBT:PCBM (1:4 w/w) achieved a power conversion efficiency of 1.05% under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Structure modification and annealing effect of polymer bulk heterojunction solar cells based on polyfluorene derivatives

Three low bandgap polyfluorene copolymers containing a donor–acceptor–donor moiety have been synthesized via Suzuki and Stille polymerization reactions. Their bandgaps and molecular energy levels (highest occupied molecular orbital and lowest unoccupied molecular orbital) varied with different polymerization methods. The molecular weight of the copolymer increased significantly through copolymerizing with a monomer having a long alkyl side chain. In order to investigate their photovoltaic properties, polymer solar cell devices based on the copolymers were fabricated with a structure of indium tin oxide/poly(styrene sulfonic acid)‐doped poly(ethylene dioxythiophene)/copolymers:[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM)/LiF/Al under the illumination of AM 1.5G, 100 mW/cm². We found that the annealing temperature had a profound effect on the power conversion efficiency (PCE) of the devices with a blend of poly[9,9‐didodecylfluorene‐alt‐(bis‐thienylene) benzothiadiazole] (PF12‐TBT) and PCBM. The PCE of the solar cell based on PF12‐TBT/PCBM (1:4) annealing at 70 °C for 20 min was 4.13% with an open‐circuit voltage (V_oc) of 1.02 V, fill factor of 55.9%, and a short‐circuit current (J_sc) of 7.24 mA/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

High‐efficiency doped polymeric organic light‐emitting diodes

Fabrication of polymer light‐emitting diodes based on emission from the phosphorescent molecule fac‐tris(2‐phenylpyridine) iridium doped into a poly(N‐vinyl carbazole) host are reported. For single‐layered devices with magnesium‐silver cathodes, the luminance efficiency at 20 mA/cm² was measured as 8.7 cd/A. This efficiency could be increased by over a factor of two by incorporation of evaporated small‐molecule layers into the device structure. Significant increases in device efficiency were also obtained without these evaporated layers by modification of the electrodes. Incorporation of 3,4‐poly(ethylene dioxythiophene):poly(styrene sulfonate) at the anode improved the device efficiency but had little impact on drive voltage. Insertion of lithium fluoride at the cathode resulted in no improvement in performance for magnesium‐silver and aluminum cathodes, but a significant improvement was realized in efficiency and drive voltage for calcium‐aluminum cathodes. Excellent device performance was observed for all three cathode metals used in conjunction with cesium fluoride. Through optimization of the electrodes and emitter‐layer thickness, devices exhibiting efficiencies as high as 37.3 cd/A are realized. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2715–2725, 2003     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Effect of polydispersity on the bulk‐heterojunction morphology of P3HT:PCBM solar cells

Bulk heterojunctions (BHJs) based on semiconducting electron–donor polymer and electron–acceptor fullerene have been extensively investigated as potential photoactive layers for organic solar cells (OSCs). In the experimental studies, poly‐(3‐hexyl‐thiophene) (P3HT) polymers are hardly monodisperse as the synthesis of highly monodisperse polymer mixture is a near impossible task to achieve. However, the majority of the computational efforts on P3HT: phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM)‐based OSCs, a monodisperse P3HT is usually considered. Here, results from coarse‐grained molecular dynamics simulations of solvent evaporation and thermal annealing process of the BHJ are shared describing the effect of variability in molecular weight (also known as polydispersity) on the morphology of the active layer. Results affirm that polydispersity is beneficial for charge separation as the interfacial area is observed to increase with higher dispersity. Calculations of percolation and orientation tensors, on the other hand, reveal that a certain polydispersity index ranging between 1.05 and 1.10 should be maintained for optimal charge transport. Most importantly, these results point out that the consideration of polydispersity should be considered in computational studies of polymer‐based OSCs. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 895–903     

Monte Carlo morphological modelling of a P3HT:PCBM bulk heterojunction organic solar cell

To deepen the understanding of morphology evolution in bulk heterojunction P3HT:PCBM organic photovoltaics system by thermal treatment, domain‐size‐dependent interfacial energies were first determined by coarse‐grained molecular dynamics modelling and then used in Monte Carlo simulations of the morphology evolution. Thereby initial conditions associated with optimal interfacial surface area, continuous volume, as well as domain sizes, and spatial distributions of the phase separated domains were identified. In line with earlier studies, a 1:1 P3HT:PCBM blend ratio is found to exhibit the most efficient morphology for exciton dissociation and charge transport. Our simulations reveal that preseeding of P3HT crystal at the anode side prior to the annealing process will be instrumental to pin the formation of P3HT at the favorable electrode especially when seeding exceeds a threshold of 10% surface coverage, whereas denser seeding patterns beyond the threshold did not improve the active layer morphology further. The observed trilayer depth profile (in the absence of preseeded P3HT crystals) implies that the commonly used thickness 100 nm of the active layer is not ideal for ensuring that donor and acceptor phases dominate at opposite ends of the active layer. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 270–279     

Improvement of Power Conversion Efficiency of P3HT/PCBM Polymer Solar Cell Systems by Optimization of the Process Steps

In this work, different steps involved in the fabrication of polymer solar cells were optimized using P3HT/PCBM heterojunction. Steps included spinning speed for coating of the PEDOT:PSS layer, use of filter for the PEDOT:PSS layer, spinning speed for coating of the active layer, sequence of annealing of the active layer either before or after electrode deposition, and modification of the cooling mechanism (either by cooling rapidly or slowly after heating of the active layer). Investigation of these steps led to an improvement of the power-conversion efficiency (PCE) of the polymer solar cells, especially the last step involving the change of cooling mechanism, which improved PCE by 25%.     

Comparison of two types of vertically aligned ZnO NRs for highly efficient polymer solar cells

Vertically aligned ZnO nanorods (NR) are prepared by two different syntheses methods and applied on polymer solar cells (PSCs). The ZnO electrodes work as the electron transport layer with the P3HT:PCBM blend acting as the active material. Several organic blend solution conditions are optimized: concentration, solvent, and deposition speed. The effect of different NR electrode morphologies is analyzed on the solar cell performance and characterized by current–voltage curves and IPCE analyses. The photovoltaic performance of the solar cells was observed to be influenced by many factors, among them infiltration of the organic P3HT:PCBM blend within the ZnO NR layer. The infiltration of the active layer was monitored by cross section SEM and energy dispersive X-ray spectroscopy analyses. Our results show that higher power conversion efficiencies are achieved when shorter NRs lengths are applied. The best power conversion efficiency obtained was 2.0% for a 400 nm ZnO NR electrode. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Supramolecular assembly of H‐bonded side‐chain polymers containing conjugated pyridyl H‐acceptor pendants and various low‐band‐gap H‐donor dyes bearing cyanoacrylic acid groups for organic solar cell applications

Novel supramolecular side‐chain polymers were constructed by complexation of proton acceptor (H‐acceptor) polymers, i.e., side‐chain conjugated polymers P1–P2 containing pyridyl pendants, with low‐band‐gap proton donor (H‐donor) dyes S1–S4 (bearing terminal cyanoacrylic acids) in a proper molar ratio. Besides unique mesomorphic properties confirmed by DSC and XRD results, the H‐bonds of supramolecular side‐chain structures formed by pyridyl H‐acceptors and cyanoacrylic acid H‐donors were also confirmed by FTIR measurements. H‐donor dyes S1–S4 in solid films exhibited broad absorption peaks located in the range of 471–490 nm with optical band‐gaps of 1.99–2.14 eV. Furthermore, H‐bonded polymer complexes P1/S1–P1/S4 and P2/S1–P2/S4 exhibited broad absorption peaks in the range of 440–462 nm with optical band‐gaps of 2.11–2.25 eV. Under 100 mW/cm² of AM 1.5 white‐light illumination, the bulk heterojunction polymer solar cell (PSC) devices containing an active layer of H‐bonded polymer complexes P1/S1–P1/S4 and P2/S1–P2/S4 (as electron donors) mixed with [6,6]‐phenyl C₆₁ butyric acid methyl ester (i.e., PCBM, as an electron acceptor) in the weight ratio of 1:1 were investigated. The PSC device containing H‐bonded polymer complex P1/S3 mixed with PCBM (1:1 w/w) gave the best preliminary result with an overall power conversion efficiency (PCE) of 0.50%, a short‐circuit current of 3.17 mA/cm², an open‐circuit voltage of 0.47 V, and a fill factor of 34%. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5998–6013, 2009     

Metal‐conducting polymer interface studied by Kelvin probe microscopy: Au and Al on poly(3‐octyl‐thiophene)

In this work, we report a Kelvin probe microscopy investigation on the structural and electronic properties of gold and aluminum thin films evaporated on poly(3‐octyl‐thiophene) films. Our experimental setup allows us to perform scanning force microscopy (SFM) studies of the same area even if the sample is taken out of the SFM system for different processes (Au and Al evaporation). This allows a detailed study of the effect of adsorbed metal particles on the morphology and electrical properties of polymer thin films at the nanoscale. We found different behavior for both metals in morphology and electrical properties at the interface. These results can contribute to explain what happens at the metal–polymer interface of the devices when the metal contacts are grown. Thereby the observed nanoscale structural changes can be correlated with the overall performance of the fabricated devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1083–1093     

Synthesis and electroluminescent properties of a phenothiazine‐based polymer for nondoped polymer light‐emitting diodes with a stable orange‐red emission

A novel phenothiazine‐based polymer was synthesized through the Heck reaction of 3,7‐divinyl‐N‐octyl‐phenothiazine with 4,7‐dibromo‐2‐octylbenzotriazole according to the alternating donor–acceptor strategy. The polymer was characterized with ¹H NMR, infrared spectroscopy, gel permeation chromatography, cyclic voltammetry, ultraviolet–visible spectroscopy, and fluorescence spectroscopy. With the polymer used as an active layer, three nondoped polymer light‐emitting diodes (PLEDs) with a double‐layer configuration were fabricated by the spin‐coating approach with different thermal annealing processes. The emission maximum in electroluminescent spectra was stabilized at 616 nm. The maximum luminance reached 2432 cd/m². The coordinate value of Commission International de l'Eclairage 1931 in the double‐layer PLEDs after the thermal treatment was nearly stabilized at (x, y) =(0.62, 0.38). Additionally, the luminous efficiency of device II reached a balanceable state with an increase in the current. Therefore, the polymer had an orange‐red emission with stable chromaticity coordinates under different driving voltages. Finally, a nondoped device with a stable luminous efficiency and chromaticity was obtained. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4867–4878, 2007     

Solid‐state NMR as a tool to describe and quantify the morphology of photoactive layers used in plastic solar cells

The optimization and control of the nanomorphology of thin films used as active layer in bulk heterojunction (BHJ) plastic solar cells is of key importance for a better understanding of the photovoltaic mechanisms and for increasing the device performances. Hereto, solid‐state NMR relaxation experiments have been evaluated to describe the film morphology of one of the “work‐horse” systems poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene‐vinylene)/[6, 6]‐phenyl‐C₆₁butyric acid methyl ester (MDMO‐PPV/PCBM) in a quantitative way. Attention is focused on the influence of the processing solvent (toluene vs. chlorobenzene), the blend composition, and the casting technique, that is, spin coating versus doctor blading. It is demonstrated that independently of the solvent and casting technique, part of the PCBM becomes phase separated from the mixed phase. Whereas casting from toluene results in the development of well‐defined PCBM crystallites, casting from chlorobenzene leads to the formation of PCBM‐rich domains that contain substructures of weakly organized PCBM nanoclusters. The amount and physico‐chemical state of the phase separated PCBM is quantified by solid‐state NMR relaxation times experiments. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Regioregularity and solar cell device performance of poly(3‐dodecylthienylenevinylene)

Influence of side chain regioregularity on photovoltaic performance has been investigated in bulk heterojunction solar cells based on a series of poly(3‐dodecylthienylenevinylene)s (C₁₂‐PTV) and 6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM). Performance of each C₁₂‐PTV is optimized for fair comparison. It is found that regiorandomness has no detrimental effect on device performance, in sharp contrast to poly(3‐hexylthiophene) (P3HT). Fully regioregular C₁₂‐PTV performs slightly poorer than less regioregular ones mainly due to its fast crystallization behavior. The results suggest that introduction of side chain regiorandomness is an effective strategy to enhance processability of certain types of polymers without a reduction in photovoltaic performance. The better polymer:PCBM weight ratio, found to be 3:7 for all C₁₂‐PTVs, and improved device performance, as compared with the literature work on the same polymer synthesized by a different method, demonstrate again the importance of the integrity of polymer main chain structure. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

New conjugated copolymers based on benzo[1,2‐b; 3,4‐b′]dithiophene and derivatives of benzo[g]quinoxaline for bulk heterojunction solar cells

A series of new low‐band gap copolymers based on dioctyloxybenzo[1,2‐b;3,4‐b′] dithiophene and bis(2‐thienyl)‐2,3‐diphenylbenzo[g]quinoxaline monomers have been synthesized via a Stille reaction. The effect of different functional groups attached to bis(2‐thienyl)‐2,3‐diphenylbenzo[g]quinoxaline was investigated and compared with their optical, electrochemical, hole mobility, and photovoltaic properties. Polymer solar cell (PSC) devices of the copolymers were fabricated with a configuration of ITO/ PEDOT: PSS/copolymers: PCBM (1:4 wt ratio)/Ca/Al. The best performance of the PSC device was obtained by using PbttpmobQ as the active layer. A power conversion efficiency of 1.42% with an open‐circuit voltage of 0.8 V, a short‐circuit current (JSC) of 5.73 mA cm⁻², and a fill factor of 30.9% was achieved under the illumination of AM 1.5, 100 mW cm⁻². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effect of solvent additives on bulk heterojunction morphology of organic photovoltaics and their impact on device performance

Morphology of the active layer in an organic photovoltaic (OPV) device is known to have a significant impact on the device performance. It is, however, difficult to characterize nanoscale morphologies in detail, especially at the ensemble level. Herein, we report the utilization of small angle neutron scattering (SANS) to investigate variations in the nanoscale morphologies of the active layer of poly(3-hexylthiophene-2,5-diyl):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk heterojunction OPV depending on the composition of casting solvent. Both the power law and the poly hard sphere model were utilized to characterize the state of the donor and acceptor components, respectively, from the obtained SANS data. Furthermore, the relationship between the nanoscale morphology and device performance is outlined. It was found that the use of 2-chlorophenol, a poor solvent for P3HT and, at the same time, a very good solvent for PCBM, leads to nanomorphology featuring ordered, highly crystalline P3HT and small (15.2 nm) PCBM domains. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 128–134     

Quantifying the elasticity and viscosity of geometrically confined polymer films via thermal wrinkling

We apply thermal wrinkling, which is a surface instability that occurs during thermal annealing of polymer films geometrically confined by a rigid substrate and a flexible superstrate, to study the elasticity and viscosity of chemically crosslinked polymer systems. Specifically, we study the thermal wrinkling of aluminum‐capped polyhydroxystyrene films with different extent of chemical crosslinking and find that that the rate of change of the wrinkling wavelength with annealing time and temperature has unique relationships with the elasticity and viscosity of the polymer network. With the aid of analytical expressions that relate the time‐ and temperature‐dependent evolution of the wrinkle wavelength to the elasticity and viscosity, we are able to quantify the elastic modulus and shear viscosity of geometrically confined polymer thin films as a function of the degree of crosslinking. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Stabilization of the film morphology in polymer: Fullerene heterojunction solar cells with photocrosslinkable bromine‐functionalized low‐bandgap copolymers

Novel bromine‐functionalized photocrosslinkable low‐bandgap copolymers, PBDTTT‐Br25 and PBDTTT‐Br50, are synthesized via Stille cross‐coupling polymerization for the purpose of stabilizing the film morphology in polymer solar cells (PSCs). Photocrosslinking of PBDTTT‐Br25 and PBDTTT‐Br50 copolymers dramatically improves the solvent resistance of the active layer without disrupting the molecular ordering and charge transport, which is confirmed by the insolubility of the films washed by organic solvents and by their thermal behavior. As a result, the formation of large aggregations of fullerene is suppressed in polymer:fullerene blend films even after prolonged thermal annealing, and the stability of the device is enhanced when compared with cells based on noncrosslinkable PBDTTT. The power conversion efficiency of the PSCs based on PBDTTT‐Br25 and PBDTTT‐Br50 reaches 5.17% and 4.48%, respectively, which is improved obviously in comparison with that (4.26%) of the PSCs based on the control polymer PBDTTT. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3123–3131