Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

新半金属Fe2LaO4磁电性能的第一性原理计算

利用基于密度泛函理论的第一性原理赝势法设计并优化了含稀土元素的新半金属Fe₂LaO₄。详细计算了其电荷分布,分子磁矩等磁电性能，并结合配位场理论分析了其电子结构。结果表明，Fe₂LaO₄是一种含稀土元素的铁磁性的新ⅡB型半金属；它的稳定相晶格常数约为0.623 nm，分子磁矩约为1.0μ_B；Fe₂LaO₄属软铁磁性半金属；La较多的外层电子增强了Fe₂LaO₄内部的库仑斥力,导致了配合物ML₄和ML₆均受强场作用,从而使Fe₂LaO₄具有软铁磁性；考虑自旋分布后ML₄和ML₆的电子结构分别为a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓e_g²↑e_g²↓t_2g³↑t_2g³↓和a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓t_2g³↑t_2g³↓e_g²↑e_g²↓e_g^*1↑,这些电子属于分子轨道。     

溴代烷烃与活性氮的反应发光研究

在流动余辉装置上, 利用N₂空心阴极放电制备活性氮, 研究了活性氮与溴代烷烃(CHBr₃、CH₂Br₂、C₂H₅Br、C₄H₉Br) 反应的化学发光.上述所有反应中, 在550～750 nm波段均观察到了较强的NBr (b¹Σ+→X³Σ^-)跃迁发射谱. 同时在活性氮与CHBr₃和CH₂Br₂的反应中, 在流动管下游还观察到了CN (A²π, B²π→X²Σ⁺)的发射谱. 验证性的实验表明, 激发态NBr (b¹Σ⁺)是由二步过程形成: N(⁴S)与溴代烷烃反应生成NBr (X³Σ^-), 再通过N₂ (A ³Σ_u⁺)分子能量转移到激发态NBr (b¹Σ⁺); 而激发态的CN是通过N(⁴S) + CBr→CN(A, B) + Br过程形成的.     

白光LED用Sr0.955Al2Si2-xTixO8：Eu2+荧光粉的晶体结构和光谱特性

由高温固相反应制得Sr_0.955Al₂Si_2-xTi_xO₈：Eu²⁺（x=0~1.0）系列试样,研究了Ti⁴⁺置换Si⁴⁺对其晶体结构和光谱特性的影响。Ti⁴⁺以类质同相替代Si⁴⁺进入晶体晶格中,形成了连续固溶体,其晶胞参数a,b,c,β和晶胞体积V随Ti⁴⁺置换量呈线性递增。Ti⁴⁺置换Si⁴⁺对晶胞参数c的影响显著,b其次,a最小。荧光激发谱为宽带,位于230~400nm,由267nm、305nm、350nm和375nm 4个峰拟合成,表观峰值位于351nm;随着Ti⁴⁺置换量的增加,半高宽（FWHM）从105nm减小到93nm。发射光谱位于380~600nm,表观峰值位于407nm,可由406nm和441nm两峰拟合而成并且随Ti⁴⁺置换量增加线性红移,Ti⁴⁺进入晶格对长波长发射中心影响较少;Ti⁴⁺置换量为1.0时,表观发射峰位从407nm红移至417nm;利用试样荧光光谱和VanUitert经验公式,得出SrAl₂Si₂O₈：Eu²⁺中Sr²⁺的配位数为9。随着Ti⁴⁺置换量Si⁴⁺进入基质晶格,造成Eu-O距离变小,使得Eu²⁺所处的晶体场强度增强,发光中心Eu²⁺的5d能级分裂增大,造成Eu²⁺最低发射能级重心下移,两拟合谱峰峰位均呈线性红移。     

三元体系YCl3-CdCl2-H2O和四元体系YCl3-CdCl2-HCl(～8.8%)-H2O (25 ℃)的相平衡及其固相新化合物的研究

The equilibrium solubilities of the ternary system YCl₃-CdCl₂-H₂O, the quaternary system YCl₃-CdCl₂-HCl(～8.8%)-H₂O were determined at 25 ℃ and the phase diagrams were constructed. The results show that the ternary system was complicated with six equilibrim solid phases CdCl₂·2.5H₂O, CdCl₂·H₂O, 8CdCl₂·YCl₃·15H₂O (8∶1 type), 4CdCl₂·YCl₃·13H₂O(4∶1 type), 5CdCl₂·2YCl₃·26H₂O (5∶2 type) and YCl₃·6H₂O. The quaternary system was also complicated with four equilibrim solid phase CdCl₂·H₂O, 4CdCl₂·YCl₃·13H₂O (4∶1 type), 5CdCl₂·2YCl₃·26H₂O(5∶2 type) and YCl₃·6H₂O. Among the three new compounds 8CdCl₂·YCl₃·15H₂O, 4CdCl₂·YCl₃·13H₂O and 5CdCl₂·2YCl₃·26H₂O, 8CdCl₂·YCl₃·15H₂O was a kind of metastable compound only in ternary system, and it was changed into 4CdCl₂·YCl₃·13H₂O with time. Both 4∶1 type and 5∶2 type existed in ternary and quaternary system, but they were also congruently soluble compounds in quaternary system. They have been prepared from the system and have been characterized by XRD, TC-DTG and DSC.     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

纳米Mn-Zn铁氧体的制备和研究

Nanosize manganese zinc ferrites were fabricated by hydrothermal precipitation route using Fe₂(SO₄)₃, ZnSO₄·7H₂O, MnSO₄·H₂O as material, then some calcinated at 500 ℃ and studied by XRD, TEM, IR and VSM. The results showed that the products were spinel crystal structure and uniformly sized nanoparticles (15～25 nm) with little aggregation. The analysis of IR showed that the superficial water can be eliminated, but that was embedded in crystal lattice can not be removed by calcinating. The effect Zn content x on the lattice (a) of nanosize Mn_1-xZn_xFe₂O₄ was also discussed. The lattice of nanosize Mn_1-xZn_xFe₂O₄ decreases with x increasing; and its value deviated the standard lattice (a₀) of normal size manganese zinc ferrites. A lot of water was absorbed during the hydrothermal process owing to the large surface of nanosize particles. The change of magnetic properties of Mn_xZn_1-xFe₂O₄ with x increasing was studied: nanosize Mn_xZn_1-xFe₂O₄ particles synthesized by us exhibited peculiar magnetic properties curve with Zn content (x) increasing, Superparamagnetic behaviors of the synthesized ZnFe₂O₄ samples were confirmed by magnetic characterization, which can be explained by the difference between the distribution of the metal ions (Mn²⁺, Zn²⁺ and Fe³⁺) among the tetrahedral (A) and the octahedral (B) sites of nanosize ferrite and that of bulk ferrite.     

VB2n-(n=8~12)团簇几何结构、电子及热力学特性的理论研究

基于卡里普索结构预测程序和密度泛函理论的第一性原理计算,搜索确定了VB_2n^-（n=8~12）团簇的基态和亚稳态结构。结果发现,V原子的掺杂完全改变了原硼团簇的结构并提高了原体系的稳定性。掺杂体系基态结构分别呈现高对称性的鼓状（VB₁₆^-：C_2v）、管状（VB₁₈^-：C_2v和VB₂₀^-：C_s）及笼状（VB₂₂^-：C₂和VB₂₄^-：D_3h）结构。基于基态结构,研究了体系的电荷转移和极化率,拟合出了光电子能谱、红外和拉曼谱图,分析了流变键和芳香特性。最后,研究了体系的热力学特性,讨论了温度对热力学参数的影响。     

空气中合成固溶体荧光粉Ba2(Zn, Mg)Si2O7:Ce3+,Eu2+,Eu3+及其发光特性

采用高温固相法在空气中合成了Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu,yCe³⁺系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu²⁺离子的4f⁶5d¹-4f⁷跃迁,590~725 nm红光区窄带谱源于Eu³⁺的⁵D₀-⁷F_J (J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu³⁺在Ba_1.97-yZn_1-xMg_xSi₂O₇基质中被还原成了Eu²⁺;当x=0.1时,荧光粉Ba_1.97Zn_0.9Mg_0.1Si₂O₇:0.03Eu的绿色发光最强,表明Eu³⁺被还原成Eu²⁺离子的程度最大。当共掺入Ce³⁺离子后,形成Ba_1.97-yZn_0.9Mg_0.1Si₂O₇:0.03Eu,yCe³⁺荧光粉体系,其发光随着Ce³⁺离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba_1.96Zn_0.9Mg_0.1Si₂O₇:0.01Ce³⁺,0.03Eu的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba₂Zn_0.9Mg_0.1Si₂O₇基质中的能量传递与发光机理。     

不同温度下VUV光激发的Pr3+离子的发光性质

The luminescent properties of Pr³⁺-doped LaB₃O₆, SrAl₁₂O₁₉, SrB₄O₇ and NaYF₄ in the vaccum ultraviol-et (VUV) range at different temperatures were investigated under the excitation of high-energetic synchrotron radiation. For Pr³⁺ ions in LaB₃O₆, SrAl₁₂O₁₉ and SrB₄O₇, only the parity-forbidden ¹S₀→4f² transitions were observ-ed in the emission spectra at relatively low temperature; but the parity-allowed 4f5d→4f² transitions appeared simultaneously when the temperature was high enough. And the intensity of broad 4f5d→4f² emission increased relative to the intensity of ¹S₀→4f² emissions with increasing temperature. Then the thermal equilibrium model of energy levels was employed to the lowest 4f5d state and ¹S₀ state of Pr³⁺ in the three hosts. The calculated curves were in good agreement with the experimental values, indicating the occurrence of the thermal excitation from ¹S₀ state to 4f5d states at high temperatures when the lowest 4f5d state lies higher than ¹S₀ state and the photon energy is high enough.     

A flame‐retardant DOPO‐MgAl‐LDH was prepared and applied in poly (methyl methacrylate) resin

A novel inorganic and organic composite flame retardant (9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide [DOPO]–layered double hydroxide [LDH]) was synthesized via grafting DOPO with organic‐modified Mg/Al‐LDH, which was introduced into poly (methyl methacrylate) (PMMA) resin to prepare the flame‐retardant PMMA composites. Thermogravimetric analyzer (TGA) showed that the T_‐50% of DOPO‐LDH/PMMA composites enhanced by about 20°C, and with the 20% flame retardant, the residual char content can be increased by 39.8% in the air atmosphere compared with LDH/PMMA composites. In the UL‐94 and the limiting oxygen index (LOI) tests, it can be found that compared with LDH/PMMA composites, the LOI value of DOPO‐LDH/PMMA composites were raised evidently with the increased flame retardants, and the droplet combustion was greatly improved. These results could be ascribed to the action of DOPO free‐radical, catalytic charring of polymer and the effect of LDH physical barrier. Moreover, the novel DOPO‐LDH not only given PMMA a good flame‐retardant property and thermal stability, but also have higher visible light transmittance, ultraviolet‐shielding effect, and low loss of mechanical properties, which could further facilitate the wide application of inorganic environment‐friendly flame retardants in general resins and engineering resins and broaden the application of polymers.     

Effects of incorporation of modified silica nanoparticles on the mechanical and thermal properties of PMMA

Silica nanoparticles of various sizes have been incorporated by melt compounding in a poly(methyl methacrylate) (PMMA) matrix to enhance its thermal and mechanical properties. In order to improve nanoparticles dispersion, PMMA grafted particles have been prepared by atom transfer radical polymerization (ATRP) from well-defined silica nanoparticles. This strategy was expected to ensure compatibility between both components of the PMMA nanocomposites. TEM analysis have been performed to evaluate the nanosilica dispersion whereas modified and non-modified silica/PMMA nanocomposites thermal stability and mechanical properties have been investigated by both thermogravimetric and dynamical mechanical analysis.     

Synthesis of a novel phosphate‐containing highly transparent PMMA copolymer with enhanced thermal and flame retardant properties

A novel poly(methyl methacrylate) (PMMA)‐based copolymer (PMMA‐co‐BDPA) rich in aromatic rings was synthesized via radical copolymerization between a phosphorus‐containing acrylic monomer (BDPA) and methyl methacrylate (MMA). UV‐vis spectroscopy demonstrated that the copolymer had high transparency. Thermogravimetric analysis (TGA) and a differential scanning calorimeter (DSC) were used to test the thermal properties of the composites. Additionally, the PMMA‐co‐BDPA‐15 copolymer exhibited a 23% increase in the limited oxygen index (LOI) value. A cone calorimeter test indicated that the peak heat release rate (pk‐HRR) of PMMA‐co‐BDPA was reduced by 29.2% compared with that of pure PMMA, and the carbon yield of burning was obviously increased. The combined test results demonstrated that the prepared copolymer material had good transparency, thermal stability, and flame retardancy.     

Coagulation method for preparing single-walled carbon nanotube/poly(methyl methacrylate) composites and their modulus,electrical conductivity,and thermal stability

A coagulation method providing a better dispersion of single-walled carbon nanotubes (SWNTs) in a polymer matrix was used to produce SWNT/poly(methyl methacrylate) (PMMA) composites. Optical microscopy and scanning electron microscopy showed an improved dispersion of SWNTs in the PMMA matrix, a key factor in composite performance. Aligned and unaligned composites were made with purified SWNTs with different SWNT loadings (0.1–7 wt %). Comprehensive testing showed improved elastic modulus, electrical conductivity, and thermal stability with the addition of SWNTs. The electrical conductivity of a 2 wt % SWNT composite decreased significantly (>10⁵) when the SWNTs were aligned, and this result was examined in terms of percolation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3333–3338, 2003     

Preparation of poly (methyl methacrylate)/LDH nanocomposite by exfoliation-adsorption process

Exfoliated nanocomposite based on Mg, Al layered double hydroxide (Mg,Al-LDH) and poly(methyl methacrylate) (PMMA) has been prepared by exfoliation/adsorption process with acetone as co-solvent. The product was characterized by X-ray diffraction (XRD), thermal analysis and High Resolution Transmission Electronic Microscope (HREM). The results suggest that the brucite-like sheets of LDH disperse individually in the polymer matrix, and the thermal stability of the nanocomposite increases highly.     

The role of the trivalent metal in an LDH: Synthesis, characterization and fire properties of thermally stable PMMA/LDH systems

Two layered double hydroxides (LDHs), calcium aluminum undecenoate (Ca₃Al) and calcium iron undecenoate (Ca₃Fe), have been prepared by the co-precipitation method. XRD analysis of these LDHs reveals that they are layered materials and FT-IR and TGA confirmed the presence of the undecenoate anions in the material produced. The PMMA composites were prepared by bulk polymerization and the samples were characterized by XRD, TEM, TGA and cone calorimetry. Both additives greatly enhance the thermal stability of PMMA, while the calcium aluminum LDH gives better results when the fire properties were examined using the cone calorimeter.     

Preparation and physical properties of flame retardant acrylic resin containing nano-sized aluminum hydroxide

Poly(methylmethacrylate) (PMMA) shows high strength and transparency but is a flammable material. In this study, the surface of aluminum hydroxide was modified with methacrylate containing phosphoric acid moieties before dispersion in MMA, and organic-inorganic nano-hybrid materials were obtained by bulk polymerization in the presence of the surface-modified aluminum hydroxide. The resulting hybrid materials retained the high transparency of PMMA, with transparency values similar to that of pure PMMA. Moreover, the flame resistance of the hybrid materials was improved in comparison with that of pure PMMA, with depression of the horizontal burning rate becoming a maximum at an inorganic content of 3 wt%. These results suggest that the use of aluminum hydroxide surface-modified with phosphoric acid groups is an efficient method for obtaining good performance fire-resistant polymer materials.     

A comparison of the fire retardancy of poly(methyl methacrylate) using montmorillonite, layered double hydroxide and kaolinite

Montmorillonite, layered double hydroxide and kaolinite, have been used to make (nano)composites with poly(methyl methacrylate). X-ray diffraction and transmission electron microscopy were used to characterize the morphology and the thermal stability and fire properties have been studied by thermogravimetric analysis and cone calorimetry. The results show that LDH and MMT are better dispersed in PMMA than is kaolinite; the MMT layers have a higher aspect ratio than does the LDH. PMMA + MMT and PMMA + LDH composites have higher thermal stability than PMMA + kaolinite composite. The peak of heat release rate reduction is 55% for the PMMA + MMT composite at 10%, 45% for PMMA + LDH and 23% for PMMA-kaolinite.     

Structural characterization and thermal decomposition of layered double hydroxide/poly(p-dioxanone) nanocomposites

Nanocomposites based on layered double hydroxides (LDH) and poly(p-dioxanone) (PPDO) were prepared by melt processing using dodecylbenzene sulfonate (DBS) and 4-hydroxybenzene sulfonate (HBS) as organic modifiers. The incorporation of organic anions in LDH was demonstrated by wide-angle X-ray scattering (WAXS) and Fourier transform infrared (FTIR). The dispersion degree of the organically modified LDHs in the PPDO matrix was analyzed by WAXS, indicating that only the LDH modified with HBS was exfoliated. The effect of the organically modified LDHs on the thermal stability of PPDO was studied using thermogravimetric analysis (TGA). The thermal stability of PPDO matrix was enhanced by the incorporation of the LDH modified with HBS due to the shielding effect of the exfoliated layers. In contrast, the LDH modified with DBS produced a decrease of the thermal stability of PPDO, probably due to hydrolytic decomposition of ester group. The thermogravimetric analysis also showed that the organo-modified LDH did not modify the thermal decomposition mechanism of the polymer, but had an effect on the thermal stability.     

Investigation of Structural,Rheological and Thermal Properties of PMMA/ONi-Al LDH Nanocomposites Synthesized via Solvent Blending Method: Effect of LDH Loading

This article addresses the synthesis of organically tailored Ni-Al layered double hydroxide(ONi-Al LDH) and its use in the fabrication of exfoliated poly(methyl methacrylate)(PMMA) nanocomposites. The pristine Ni-Al LDH was initially synthesized by co-precipitation method and subsequently modified using sodium dodecyl sulfate to obtain ONi-Al LDH. Nanocomposites of PMMA containing various amounts of modified Ni-Al LDH(3 wt%?7 wt%) were synthesized via solvent blending method to investigate the influence of LDH content on the properties of PMMA matrix. Several characterization methods such as X-ray diffraction(XRD), transmission electron microscopy(TEM), Fourier transform infrared spectroscopy(FTIR), rheological analysis, differential scanning calorimetry(DSC) and thermo gravimetric analysis(TGA), were employed to examine the structural, viscoelastic and thermal properties of PMMA/OLDH nanocomposites. The results of XRD and TEM examination confirm the formation of partially exfoliated PMMA/OLDH nanocomposites. The FTIR results elucidate that the characteristic bands for both pure PMMA and modified LDH are present in the spectra of PMMA/OLDH nanocomposites. Rheological analyses were carried out to examine the adhesion between polymer matrix and fillers present in the nanocomposite sample. The TGA data indicate that the PMMA nanocomposites exhibit higher thermal stability when compared to pure PMMA. The thermal decomposition temperature of PMMA/OLDH nanocomposites increases by 28 K compared to that of pure PMMA at 15% weight loss as a point of reference. In comparison with pure PMMA, the PMMA nanocomposite containing 7 wt% LDH demonstrates improved glass transition temperature(Tg) of around 3 K. The activation energy(Ea), reaction orders(n) and reaction mechanism of thermal degradation of PMMA/OLDH nanocomposites were evaluated using different kinetic models. Water uptake capacity of the PMMA/OLDH nanocomposites is less than that of the pure PMMA.