改性介孔 Al2O3 负载锰基催化剂的结构及其催化氧化与抗硫性能

 采用分步浸渍法分别制备了 LaCeZr 和 YCeZr 组合助剂改性的介孔 Al2O3 负载的 Mn 基系列氧化物催化剂, 用 X 射线衍射、氮气吸附-脱附、X 射线吸收精细结构、X 射线光电子能谱和程序升温还原等方法对催化剂进行了表征, 探讨了催化剂中 Mn 物种的存在形式及其还原性能, 并与样品催化 CO 和 C3H8 的氧化活性相关联. 结果表明, 样品中 Mn 物种主要以 Mn3O4 形式存在, 该物种在不同样品中与载体的作用强弱不同, 从而表现出不同的还原性能和催化活性. 助剂改性有效抑制了 Mn-Al 之间的相互作用, 提高了 Mn–O 键的活动度, 从而提高了催化剂的氧化活性. 相比于 YCeZr 助剂, LaCeZr 助剂改性更大程度上提高了 Mn 物种的还原性, 因而大大提高了催化剂的氧化性能. 650 oC 焙烧的 LaCeZr 组合助剂改性的介孔 Al2O3 负载的 Mn 氧化物催化剂, 在 0.035% SO2 存在的条件下对 CO 的氧化活性并未下降, 对 C3H8 的氧化活性下降幅度也较小, 表现出优越的抗硫性能和氧化性能.     

介孔硅负载Keggin型钨磷酸催化环己烯环氧化(英文)

采用共合成法制备了一系列不同硅氨基含量的介孔氧化硅SBA-15,在其孔道中引入Keggin型钨磷酸,且其含量随硅氨基含量的增加而增加. 考察了不同处理温度下杂多酸的热稳定性,发现焙烧后钨物种能在SBA-15孔道内高度分散. 以H2O2为氧化剂,研究了该催化剂在环己烯环氧化反应中的催化活性,考察了杂多酸负载量和焙烧温度对催化活性的影响. 结果表明,400 C处理后的钨磷酸催化剂具有高的反应活性和重复使用性能.     

聚谷氨酸修饰电极同时检测对苯二酚和邻苯二酚

以谷氨酸单体为初始试剂,利用电化学聚合方法制备得到聚谷氨酸修饰电极.考察了电化学聚合条件(电位、扫速及扫描圈数)对修饰电极的影响,运用电化学方法对所制备的修饰电极进行了表征.此修饰电极对对苯二酚和邻苯二酚的电化学氧化还原显示出很高的催化能力,显著降低了二者的氧化电位,改善了二者的电化学可逆性,同时增强了二者的氧化还原峰...     

高效WO3掺杂MCF催化剂的合成及其在环戊烯选择氧化制戊二醛反应中的应用

以钨酸钠和正硅酸乙酯为前驱体直接合成高含量WO₃掺杂介孔氧化硅泡沫(MCF)催化剂. 在773 K焙烧后显示出更高的热稳定性. 小角X射线散射, N₂-物理吸附和透射电子显微镜结果表明钨物种嵌入后, 材料仍保持MCF特征的三维织构介孔特征. 紫外拉曼和紫外可见漫反射光谱结果表明钨物种主要以孤立的或者低聚态的氧化钨形式存在, 所以在氧化钨质量分数(w)低于20%时氧化钨物种能够高度分散在载体上. 在环戊烯选择氧化制戊二醛反应中, 反应16 h 后环戊烯的转化率达到100%, 戊二醛的产率达到83.5%. 催化剂重复利用实验表明催化剂的稳定性较好, 没有钨物种的脱落. 这种优异的催化性能归结于合适的氧化钨含量和高分散的钨物种.     

CuO/Ce0.5Zr0.5O2的结构特征及催化性能表征

以硝酸铈和硝酸锆为原料,采用共沉淀法制备了不同摩尔比(X=0,0.1,0～1.0)的CexZr1-xO2样品.并以Ce0.5Zr0.5O2为载体,采用浸渍法负载不同含量的CuO,用色谱流动法考察其对CO的氧化活性.并用XRD,TPR和BET等技术对CuO/Ce0.5Zr0.5O2各样品进行了表征,结果表明,当CuO负载量为10.0%时,催化剂CO的氧化活性最高;XRD测定表明催化剂氧化活性的高低与铜物种在Ce0.5Zr0.5O2上的分散状态有关;TPR结果亦显示活性的高低与Ce0.5Zr0.5O2上分散较好的铜物种的α还原峰及分散较差的γ还原峰的峰温及形状有关.     

介孔氧化铝负载钒催化剂上丙烷氧化脱氢制丙烯

 采用浸渍法制备了介孔氧化铝 (m-Al2O3) 负载钒催化剂 (V/m-Al2O3), 并考察了其催化丙烷氧化脱氢制丙烯反应活性. 通过 N2 吸附-脱附、透射电镜、X 射线粉末衍射、紫外-可见漫反射光谱、氢-程序升温还原和氨-程序升温脱附对催化剂进行了表征. 结果表明, 介孔氧化铝具有大比表面积、窄孔径分布和两维六方相结构, 在其上负载适量的 V 可实现 V 活性物种的高分散及催化剂的弱酸性, 从而有利于提高丙烷转化率和丙烯选择性. 与共合成法制备的含 V 介孔氧化铝 V/m-Al2O3(C) 和浸渍法制备的 V/?-Al2O3 相比, V/m-Al2O3 表现出更高的催化活性. 这与载体较弱的酸性和较大的比表面积以及 V 物种的高分散有关.     

负载TS-1导向剂的介孔材料的合成、表征及催化性能研究

利用浸渍法将TS-1导向剂高度分散在介孔材料MCM-41和SBA-15的表面,制备出一系列在氧化反应中具有高活性的催化材料.对样品的表征显示催化剂保持了介孔的结构,同时具有四配位的钛物种均匀地分散于介孔催化剂的表面.催化结果显示,与钛硅分子筛(TS-1)相比,所制备的催化剂在小分子的氧化反应中表现出相似的活性,在大分子的氧化反应中展示了很高的活性,体现了介孔材料的优越性.     

介孔Co-Al2O3催化剂上甲烷部分氧化制合成气

采用一锅法制备了介孔Co-Al2O3催化剂,并首次用于甲烷部分氧化制合成气反应. 结果表明,与普通浸渍法相比,一锅法制备的Co-Al2O3催化剂表现出更为优异的催化性能. 合成的介孔Co-Al2O3催化剂具有大的比表面积和孔体积,以及规整有序的六方介孔孔道,Co物种高度分散,从而导致还原后高的金属分散度,而介孔孔道对金属纳米颗粒的约束作用可有效增强金属的抗烧结能力.     

PW_(11)/SBA-15介孔杂化材料的直接合成与表征

采用三嵌段共聚物EO20PO70EO20(P123)为模板剂,正硅酸乙酯(TEOS)和缺位Keggin型多金属氧酸盐Na7PW11O39(PW11)为无机前驱体,由共缩合法一步合成了PW11/SBA-15介孔杂化材料.通过红外(IR)光谱、紫外-可见漫反射光谱(UV-Vis/DRS)、X射线衍射(XRD)、低温N2吸附、透射电子显微镜(TEM)等手段对杂化材料和合成过程进行了表征.结果表明:杂化材料中不仅多金属氧酸盐的Keggin单元保留完整,且共价键联于介孔孔道内部,而且样品基本具有规整有序的六方介孔结构.TEOS预水解时间的长短对有序结构的构筑有明显影响,随预水解时间延长,样品的介观有序性增加.这是因为多金属氧酸盐对模板剂P123有盐析作用,其作用大小与多金属氧酸盐前驱物的溶解度有关.     

W-SBA-15介孔分子筛的直接合成及其对环己烯环氧化反应的催化性能

 分别以Na2WO4和H2WO4为钨源,以正硅酸四乙酯为硅源直接合成了W-SBA-15介孔分子筛样品,并用小角XRD,N2吸附,FT-IR,UV-Vis,SEM和XRF等手段对合成的分子筛进行了表征. 结果表明,只用P123(EO20PO70EO20)为模板剂时,分子筛中钨的含量只是投料量的一半; 而以P123和十六烷基三甲基溴化铵为混合模板剂时,钨能有效地掺杂到SBA-15分子筛中. 当原料中的Si/W摩尔比为40时,W-SBA-15分子筛中的钨物种以高度分散状态存在,且以H2WO4为钨源比以Na2WO4为钨源更易将钨掺杂到SBA-15介孔分子筛中. W-SBA-15分子筛催化剂对环己烯环氧化反应具有较高的催化活性.     

Photochromic ordered mesoporous hybrid materials based on covalently grafted polyoxometalates

Novel polyoxometalate (POM)-grafting mesoporous hybrid silicas, XW(11)/MHS (X=P, Si) and TBAPW(11)Si(2)/MHS, have been prepared respectively by co-condensation and post-synthesis routes based on the employment of Keggin-type monovacant XW(11) or a Si-substituted compound TBAPW(11)Si(2) as POM precursors. Upon characterization of the samples by FT-IR, XRD, ICP-AES, TEM and N(2) adsorption-desorption measurement, it was found that Keggin units were retained perfectly in ordered hexagonal mesopore channels with SBA-15 architecture and immobilized by covalent linkages on the mesopore wall. These materials, especially the co-condensed samples, exhibited stable and reversible photochromic properties under UV irradiation although no special organic component was supplied additionally as an electron donor. An investigation of the photochromism revealed that the photochromic response depended on the centre atom of the POM species (i.e., the redox potential of the POM), the content of the POM and the synthetic route of the sample, while the bleaching process was correlated not only to the redox potential but also to the pore size of the sample. The photochromic mechanism was also studied in detail by cyclic voltammetry, ESR, FT-IR and XPS techniques. It was found that the remaining P123 template acted as a reducing agent and was oxidized during the photochromic process accompanied by the reduction of the POM to heteropolyblue. Thus, a close contact between the POM and the remaining P123 chain in the sample is necessary. Low close-contact degree results in poor photochromic behavior of the post-synthesized sample and impregnated samples.     

Electrochemical study of o-toluidine blue impregnated in mesoporous silica channels

This paper reports an electrochemical study of ordered mesoporous silica impregnated with a cationic dye (o-toluidine blue), prepared with a non-ionic surfactant as the structure-directing agent. O-toluidine blue was chosen because of its utility as an electron transfer mediator (redox catalyst). O-toluidine blue impregnated mesoporous silica was characterized by nitrogen sorption porosimetry, small angle X-ray scattering, infrared spectroscopy, scanning electron microscopy and cyclic voltammetry using chemically modified carbon paste electrodes. Results indicate that the dye is located within the ordered mesopores of micron-sized silica spheres.     

Preparation and Characterization of Mixed‐Valent Nickel Oxide/Nickel Hexacyanoferrate Hybrid Films and Their Electrocatalytic Properties

Polynuclear mixed‐valent nickel oxide and nickel hexacyanoferrate hybrid film was prepared on glassy carbon electrode by multiple scan cyclic voltammetry. The film growth was monitored using electrochemical quartz crystal microbalance (EQCM). The cyclic voltammogram of the nickel hexacyanoferrate film is characterized by single redox couple whereas nickel oxide/nickel hexacyanoferrate hybrid film exhibits two redox couples. Cyclic voltammetric features suggest that the charge transfer process in both films resembles that of surface‐confined redox species. In stronger basic solution (pH ≥9), nickel hexacyanoferrate film was gradually converted into nickel oxide film during potentiodynamic cycling. The peak potential of nickel oxide redox couple moved into more negative side with increasing pH of contacting solution whereas the peak potential of nickel hexacyanoferrate redox couple remains the same. Electrocatalytic behavior of hybrid film coated electrodes toward ascorbic acid, hydrazine and hydroxylamine was investigated using cyclic voltammetry technique. Analytical application of nickel oxide/nickel hexacyanoferrate hybrid film electrode was tested in amperometry and flow injection analysis.     

介孔碳纳米纤维制备与超电容性能研究

采用低分子量酚醛树脂/F127混合物填充多孔氧化铝模板孔道,制备了大尺寸介孔孔道、核-壳结构的介孔碳纳米纤维.分别以SEM、TEM及N2等温吸附-脱附观察分析样品形貌和孔结构参数.循环伏安与恒流充放电测定该介孔纳米纤维电极(阳极)的超电容性能.结果表明:介孔碳纳米纤维比电容明显增大,且在高扫速、大电流下具有良好的超电容特性.     

石墨烯/铂纳米粒子杂化膜测定肾上腺素

利用循环伏安法制备了石墨烯/铂纳米粒子杂化膜修饰电极,并利用该修饰电极研究了肾上腺素（EP）的电化学行为,建立了测定肾上腺素的电化学方法。 分别利用扫描电子显微镜（SEM）和循环伏安法对电极表面的形貌和电化学性能进行了表征。 试验优化了修饰电极制备过程中影响电极性能的条件和EP的测定条件。 试验结果表明,石墨烯/铂纳米粒子修饰电极对肾上腺素有明显的电催化作用。 在pH=5.0的柠檬酸 磷酸氢二钠缓冲溶液中,EP的氧化峰电流与其浓度在4.4×10-8~2.2×10-6 mol/L的范围内呈良好的线性关系。 线性方程为ipa(10 μA)=0.0753c(mol/L)+3.7653×10-5,r=0.9989,检出限为2.2×10-9 mol/L（S/N=3）。 修饰电极表具有良好的重现性,可用于实际样品的测定。     

Electroactive ceramic carbon electrode impregnated with organic liquid

The carbon ceramic electrodes impregnated with hydrophobic organic solvent (toluene, hexadecane, nitrobenzene) containing redox probe (decamethylferrocene) were prepared. The electrode material was obtained by sol–gel process. It consists of graphite powder homogeneously dispersed in hydrophobic silica matrix. After gelation and drying it was filled with organic liquid. The electrochemical properties of the electrode were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Approximately symmetric cyclic voltammograms were obtained with these electrodes immersed in aqueous electrolyte solution. Their shape and current magnitude and position on the potential scale depends on the organic solvent and the salt present in aqueous phase. It has been concluded that the mechanism of the electrode process involves electron transfer between graphite particle and the redox probe in organic phase, followed by anion transfer from the aqueous phase.     

Preparation,Characterization, and Electrocatalytic Properties of Mixed‐Valent Nickel Hexacyanoferrate/Phosphomolybdate Hybrid Film Electrodes Towards Oxidation of Ascorbic Acid and Reduction of S2O$\rm{ {_{8}^{2-}}}$

Polynuclear mixed‐valent nickelhexacyanoferrate/phosphomolybdate (NiHCF/PMo), nickel/phosphomolybdate (Ni/PMo) hybrid films were prepared on glassy carbon electrode by multiple scan cyclic voltammetry. Combination of individual components gave the opportunity to fabricate hybrid film with tunable electrochemical and analytical properties compared to individual components. The film growth was monitored using electrochemical quartz crystal microbalance (EQCM). The cyclic voltammogram of the nickelhexacyanoferrate/phosphomolybdate film is characterized by four redox couple whereas nickel/phosphomolybdate hybrid film exhibits three redox couples. Cyclic voltammetric features suggest that the charge transfer process in both films resembles that of surface‐confined redox species. The voltammetric response of nickelhexacyanoferrate/phosphomolybdate film electrode was found to be depending on the pH of the contacting solution. Electrocatalytic behavior of nickel/phosphomolybdate hybrid film coated electrodes toward oxidation of ascorbic acid and reduction of sulfur oxoanion, S₂O , was investigated using cyclic voltammetry technique. Analytical application of nickel/phosphomolybdate hybrid film electrode was tested in amperometry and flow injection analysis.     

介孔-C/MnO2非对称超级电容器的研究

以氧化硅介孔分子筛SBA-15为模板制备出介孔MnO2和介孔炭, 并分别作为正极和负极在6 mol·L-1 KOH电解液中组装出新型非对称超级电容器. 小角X射线衍射(LXRD)、透射电镜(TEM)以及N2吸附-脱附测试表明样品具有介孔结构, 且比表面积较大, 孔径分布范围较窄. 采用恒流充放电、循环伏安、交流阻抗等电化学方法考察了非对称超级电容器的性能. 在0.1 A·g-1电流密度、不同充放电电位下进行研究, 得出最佳充放电电位为1.8 V. 结果表明, 在0.1 A·g-1电流密度、1.8 V的充放电电位下电容器的充放电性能良好, 等效串联电阻(ESR)为1.15 Ω, 功率密度为89.0 W·kg-1, 能量密度达31.3 Wh·kg-1, 首次放电比容量为76.7 F·g-1, 经过1000次循环容量仍保持在69.5 F·g-1.     

Electrochemistry of polyaminobenzenes: Part 2. Oxidation of hexakis(dimethylamino)benzene at high potentials

Hexakis(dimethylamino)benzene is electrochemically oxidized to species with oxidation states higher than that of a tetracation. The reaction is followed by cyclic voltammetry. A mechanistic scheme of the electrode reaction mechanism is proposed. Computer simulations of cyclic voltammograms at scan rates between 0.02 and 50 V s⁻¹ allow the estimation of reaction parameters. A comparison of the potentials for the redox steps with data by other authors supports a re-interpretation of their results.     

金电极上偶氮腺嘌呤的电化学行为研究

本文研究了光滑金电极上偶氮腺嘌呤的电化学特性,并确定了相关动力学参数. 在含偶氮腺嘌呤的0.2 mol·L^-1的磷酸盐缓冲液(PBS,pH = 4.0 ~ 10.0）中,发现其循环伏安图上出现一对氧化还原峰. 基于对扫速和伏安峰值电位的分析,结果表明这是一个由吸附控制的可逆偶氮腺嘌呤氧化还原电化学过程. 当pH值从低到高改变时,氧化还原峰值向负电位移动,证实H⁺参与了该反应. 通过进一步实验数据分析和电极表面吸附量计算,发现该反应为分步进行的两电子两质子反应. 最后,通过快速循环伏安扫描方法确定了电化学过程的表观传递系数α和表观速率常数ks.