Nb2O5/γ-Al2O3表面铌氧物种的分散状态与酸性特征

负载型Nb2O5是多种催化反应的有效催化剂. 以草酸铌为前驱物, γ-Al2O3为载体, 通过浸渍法制备不同负载量的Nb2O5/γ-Al2O3催化剂. 采用粉末X射线衍射(XRD)、激光拉曼光谱(LRS)和吡啶吸附傅立叶变换红外(Py-IR)光谱方法对催化剂表面铌氧(NbOx)物种的分散特征、酸性特征进行表征, 通过异丁烯(IB)与异丁醛(IBA)缩合生成2,5-二甲基-2,4-己二烯(DMHD)反应评价催化剂表面酸催化活性. 结果表明, Nb在γ-Al2O3表面的单层分散容量(ΓNb)为7.6 μmol·m-2, 与“嵌入模型”理论分析Nb5+分散在γ-Al2O3优先暴露晶面(110)上八面体空位中的单层分散容量值7.5 μmol·m-2接近, 即分散的Nb5+离子键合在γ-Al2O3表面八面体空位中. 在低负载量下, 分散在γ-Al2O3表面的Nb2O5主要以孤立的NbOx物种形式通过Nb—O—Al键与载体表面键合, 与LRS结果一致. 处于孤立状态下的NbOx物种使表面Lewis 酸位量下降. 随负载量的增加, 孤立的NbOx物种通过Nb—O—Nb键连接而聚集, 并形成表面Bronsted酸位, 随着NbOx聚集度增加, 表面Bronsted 酸密度增加, 酸性增强, 对IBA与IB缩合反应催化活性增加. 当负载量超过单层分散容量时, NbOx物种呈现三维聚集状态, DMHD的转化频率(TOF)降低, 同时表面Bronsted 酸性增强, 导致目标产物DMHD 的选择性降低. Nb2O5/γ-Al2O3催化剂表面Bronsted 酸特征与NbOx物种聚集状态密切相关.     

Promoting effect of Mg in supported Mo/HBeta–Al2O3 catalyst for cross-metathesis of ethene and butene-2 to propene

Promoting effects of Mg in heterogeneous Mo/HBeta–Al₂O₃ catalyst have been carefully studied for cross-metathesis of ethene and butene-2 to propene. The catalyst shows good stability with Mg content in the range of 1–2 wt%. Such effect may be attributed to the elimination of weak acid sites through introduction of Mg which suppresses the side olefin oligomerization reaction, as evidenced from NH₃-TPD and ¹H MAS NMR results. Addition of more Mg content to 3 wt% may change the state and reducibility of Mo species, as indicated from the UV–vis, UV-Raman and H₂-TPR measurements. The increasing difficulty for the reduction of Mo(VI) species is closely related with the poor performance of 3 wt% Mg–4Mo/HBeta–30% Al₂O₃ catalyst in the metathesis reaction.     

CuO/ZnO/Y2O3/γ-Al2O3双功能催化剂上二甲醚水蒸气重整制氢

将沉积-沉淀法制备的CuO/ZnO/Y2O3催化剂同γ-Al2O3进行机械混合, 制备了CuO/ZnO/Y2O3/γ-Al2O3双功能催化剂, 用于二甲醚水蒸气重整制氢反应, 实验结果表明其活性、稳定性等均优于常用的CuO/ZnO/Al2O3/γ-Al2O3催化剂. 结合N2吸附-脱附(BET)、N2O化学吸附(N2O chemisorption)、NH3程序升温脱附(NH3-TPD)、X射线衍射(XRD)、H2程序升温还原(H2-TPR)等表征手段研究了两种催化剂在表面酸性及微观结构上的差异, 发现CuO/ZnO/Y2O3催化剂具有相对较高的铜分散度, 铜晶粒更加细小化, 并且具有高温稳定性的Y2O3可能起到隔离铜的作用, 在一定程度上防止了铜晶粒的团聚, 从而改善了重整组分的性能, 提高了双功能催化剂的重整制氢活性及稳定性.     

CeO2-MOx (M=La3+, Ca2+)改性Pd/γ-Al2O3催化甲烷燃烧性能

采用沉积-沉淀法制备了固溶体CeO2-MOx(M=La3+, Ca2+)改性的Pd/γ-Al2O3催化剂, 利用XRD、Raman和XPS对催化剂进行了表征. 结果表明, 金属(M)离子进入CeO2的晶格, 形成CeO2-MOx固溶体, Raman谱上463 cm-1处对应于Ce—O键的F2g对称伸缩振动强度降低. 其中, 样品Pd/γ-Al2O3-CeO2-CaO在615 cm-1处出现一小峰, 样品Pd/γ-Al2O3-CeO2-La2O3在320 cm-1处出现的肩峰, 都表明固溶体CeO2-MOx的形成使O2-亚晶格结构对称性降低. XPS分析表明, 固溶体改性的Pd/γ-Al2O3催化剂中Pd 的3d5/2结合能比正常价态的PdO的结合能高出0.5-0.6 eV, 形成了一种高度离子化的, 与载体具有强相互作用的Pd物种. 催化甲烷燃烧实验证明, 固溶体CeO2-MOx(M=La3+, Ca2+)改性的Pd/γ-Al2O3催化剂的低温活性和稳定性均高于未经改性的Pd/γ-Al2O3催化剂和仅用CeO2改性的Pd/γ-Al2O3催化剂, 在空速为50000 h-1时, 可使1%CH4-99%空气(体积分数)混合气中甲烷的10%转化温度降至254 ℃, 转化率100%时的转化温度降至340 ℃.     

Co-K-Mo/γ-Al2O3催化剂的合成低碳醇性能及其结构研究

氧化态Ｋ－ＭｏＯ３／γ－Ａｌ２Ｏ３催化剂中添加Ｃｏ（ＮＯ３）２后在空气中四个不同温度下焙烧再硫化,制得Ｃｏ－Ｋ－ＭｏＯ３／γＡｌ２Ｏ３催化剂,对其ＣＯ加氢合成低碳醇的催化反应性能进行了评价,运用ＸＲＤ,ＬＲＳ及ＥＸＡＦＳ等手段对催化剂及其氧化态前躯体的结构进行了表征,活性测试结果表明加Ｃｏ后于５００－６５０℃焙烧制得的催化剂活性较高,且使Ｃ２＋醇比例增加,结构分析结果显示加Ｃｏ后３５０℃焙烧时,Ｃ     

La2O3对Ni/γ-Al2O3甲烷化催化剂的助催化作用

我国将稀土作为助剂引入镍基甲烷化催化剂,大大提高了催化剂的活性和热稳定性,并已投入工业应用［1－3］．稀土对不同镍催化剂反应性能及其作用机理的研究已有一些报导［3－7］．谢有畅等观察到镍负载在经单层La2O3改性的γ－Al2O3表面,其晶粒要比没有La2O3时小得多．Rotgerink等认为添加La后反应速率的增加不只是由于几何效应,而是La对甲烷化本身有促进作用,单位镍表面的活性是随La含量不同而改变的,活性增加的同时表观活化能也增加［5］．作为助剂的La2O3在氢还原和反应过程中的变化及其作用的研究和讨论较少,目前一般认为添…     

载体酸性对Mo/HZSM-5-Al2O3催化剂上烯烃歧化反应性能的影响

在固定床反应器上考察了Mo/HZSM-5-Al2O3催化剂上乙烯与2-丁烯歧化制丙烯反应的性能.结合X射线衍射、NH3程序升温脱附、吡啶吸附红外光谱、H2程序升温还原和程序升温氧化等表征结果发现,载体酸性的差异导致催化剂酸性和 Mo物种落位方式不同.载体酸性较强时,催化剂积炭严重,反应稳定性差;载体酸性较弱时,Mo物种...     

Production of propylene from an unconventional metathesis of ethylene and 2-pentene over Re2O7/SiO2-Al2O3 catalysts

An unconventional metathesis of ethylene and 2-pentene over Re2O7/SiO2-Al2O3 catalysts has been studied as an alternative route for the production of propylene. Complete conversion of 2-pentene and propylene yield as high as 88 wt% were obtained under mild reaction conditions at 35°C and atmospheric pressure. Unlike the conventional metathesis of ethylene and 2-butenes in which isomerization is a competing side reaction, the isomerization of 1-butene product from the unconventional metathesis of ethylene and 2-pentene to 2-butenes can further react with excess ethylene in the feed, resulting in additional increase in propylene yield. The secondary metathesis reaction was found to be favored under ethylene/2-pentene (E/2P) molar ratio 3 and gas hourly space velocity (GHSV) 1000 h-1 at the reaction temperature of 35°C. No catalyst deactivation was observed during the 455 min time-on-stream under the selected reaction conditions.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体, 制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1, 0.75, 0.5, 0.25, 0). 应用Brunauer-Emmet-Teller (BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征, 并系统研究了催化剂在饮食油烟催化燃烧中的催化活性. BET结果表明催化剂的比表面积随Ce/Zr摩尔比的减小而减小. XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上. H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好. 催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧, 降低了反应温度. 随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化, 催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2>Pt/γ-Al2O3/Ce0.25Zr0.75O2>Pt/γ-Al2O3/Ce0.75Zr0.25O2>Pt/γ-Al2O3/CeO2>Pt/γ-Al2O3/ZrO2.     

Cu/ZrO2-Al2O3上表面氧物种脱附及其对催化性能的影响

采用ＸＲＤ,ＴＰＤ－ＭＳ和ＴＰＲ方法研究了ＺｒＯ２的改性对ＣｕＯ／γ－Ａｌ２Ｏ３催化剂上铜物种人散状态,表面氧物种的脱附和恢复性能,铜物种还原再氧行为的影响,并ＣＯ氧化反应为探针考察了催化剂的氧化活性,结果表明,ＺｒＯ２的存在的铜物种在γ－Ａｌ２Ｏ３载体上的分散容量降低,促进ＣｕＯ／γ－Ａｌ２Ｏ３催化剂上表面氧物种的脱附,同时有效地促进铜物种的还原,从而增加ＣＯ的氧化活性,实验还发现热处理条件对催     

Study of reduced Mo/Al2O3 metathesis catalysts prepared via metal complexes

The Mo/Al₂O₃ catalysts for propene metathesis were prepared both via anchoring Mo complexes of various nuclearities and by conventional method of impregnation. The catalysts from metal complexes were found to be active in metathesis at ambient temperature after reduction with H₂ or CO at 400–500°C. The average oxidation state of Mo in the activated catalysts was determined with regard to oxygen consumption needed for oxidation of the reduced Mo species to Mo⁶⁺.     

CeO2掺杂RuO2/γ-Al2O3催化剂结构与湿式氧化降解苯酚的活性研究

采用浸渍法制备了RuO2/γ-Al2O3和RuO2-CeO2/γ-Al2O3催化剂,利用XRD,XPS和ESR分析了催化剂的结构,并研究了湿式氧化降解苯酚的活性.结果表明,两种催化剂表面RuO2均有良好的分散性,并且催化剂表面存在氧空位和化学吸附氧,CeO2的掺杂使催化剂表面氧空位和化学吸附氧数量增加.两种催化剂对湿式氧化降解苯酚具有良好的催化活性,当苯酚质量浓度为4200mg/L,在150℃和3MPa下,RuO2/γ-Al2O3催化剂湿式氧化降解苯酚反应150min后,苯酚全部被去除,RuO2-CeO2/γ-Al2O3催化剂反应60min后,苯酚的去除率为96%.     

MoO3在低比表面载体α-Al2O3上的分散容量测定

固体化合物如无机氧化物、盐类及有机物等在高比表面载体上呈现自发分散，这是一种相当普遍的现象，在催化剂和吸附剂及材料科学研究方面已有许多研究报导［'－'］．然而，相应固体化合物在情性小比表面载体上的分散还没有人研究过．小比表面载体的结构比高比表面载体稳定，结构较易确定·本文通过表面灵敏的X射线光电子能借（XPS）和X射线衍射方法（XRD）首次测定了Moo。在小比表面。－AI。O。上的分散容量，发现它与在高比表面载体7－AI。Oa上单位面积的分散容量不同，说明a－AI。O。与7－AI。O。的表面结构不同，为研究小比表面…     

硝酸镁在γ-Al2O3上的热分解及MgO/γ-Al2O3

研究了不同载量时Mg(NO     

VOx/SiO2-Al2O3催化剂催化苯羟基化制苯酚

以硅溶胶为硅源、偏铝酸钠为铝源及环己胺合成SiO2-Al2O3复合氧化物,并采用水热合成法合成了VOx/SiO2-Al2O3催化剂。采用XRD、SEM、TEM、XPS、NH3-TPD、N2物理吸/脱附等手段对此催化剂和复合氧化物微观结构进行表征分析。由表征结果可知钒活性中心能够高分散于此复合氧化物表面,VOx/SiO2-Al2O3催化剂呈现层片积雪状;当钒的含量为4%时,催化剂中V4+含量最大且总酸量契合于此反应所需要的催化酸环境。探究了4%VOx/SiO2-Al2O3催化剂对苯羟基化制苯酚反应的催化性能,结果表明：基于高分散活性中心、V4+含量最大及载体酸性环境等优点而表现出良好的催化性能,苯转化率为48.1%,苯酚选择性为99.6%。     

负载型La0.8Sr0.2MnO3燃烧催化剂的载体效应

Combustion catalysts La0.8Sr0.2MnO3 supported on γ-Al2O3, α-Al2O3, cordierite (2MgO•2Al2O3•5SiO2) and ZrO2 were compared. Further investigation was focused on LSM/ γ-Al2O3 catalyst. It was observed that LSM/γ－Al2O3 catalyst loaded with 20% (mass fraction) LSM (La0.8Sr0.2MnO3 or corresponding oxides), heated at 750℃ or above, perovskite-type oxides were found by XRD examination, whereas, the same catalyst loaded with 10% or less LSM, perovskite oxides were absent, calcination temperature about 750℃ is necessary for the formation of perovskite structure in LSM/γ-Al2O3 catalysts. High activity of complete oxidation of xylen will be obtained when perovskite-type oxides.
Investigation of TPR showed that neat LSM or LSM/γ-Al2O3(20%) was reduced by H2-N2 mixed gas. Two degradation processes took place. In the first, reduced temperature peak was about 350 - 450℃. If reduction ended at 400℃, perovskite structure was retained, which may be due to the reduction of Mn3+to Mn2+ on the surface of LSM only. In the second process, perovskite structure was destroied, and La2O3, Mn2O3, Mn - Sr - O oxides could be obtained, which took place in the temperature range 685 - 750℃ and ended at 800℃. This was proved by TPR experiments (Fig. 3, 5) and XRD patterns (Fig. 4)
Catalysts LSM/γ-Al2O3(10% or 20%) heated at 500℃ have only one TPR peak, i. e. lower temperature peak. This is due to the absence of perovskite-type oxides in the catalysts. However, neat LSM or LSM/γ-Al2O3(20%) heated 750℃ or above, not only the first low temperature TPR peak but also the second peak, which is contributed by the perovskite-type oxides in these catalysts appeared. Therefore, the second TPR peak, i. e. the higher temperatue peak is a characteristic peak for perovskite-type oxides in the reduced process. When LSM/ γ-Al2O3 (10%) catalys is heated at 750℃, no perovskite-type oxides were detected by XRD, and the second reduction peak was absent also in TPR process. \
The order of the second reduction peak temperature(characteristic peak of perovskite - type ox- ides) is: neat LSM(750℃）> LSM/γ-Al2O3 20% (685-698℃) -deposited LSM/γ-Al2O3 (698℃) > LSM/γ-Al2O3 15% (677 - 680℃) >(LSM/γ-AL2O3 10% 620 - 630℃, for Mn - Al - O medium oxides on surface). It is correleted with the increasing of the effect of support sequentially.
When LSM/γ-Al2O3 catalysts were heated at 900℃, more stable phase, spinel MnAl2O4 appeared, which could be proved by TPR of model catalyst MnAl2O4/γ-Al2O3.     

柠檬酸对Ni2P/TiO2-Al2O3催化剂加氢脱硫性能的影响

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,以柠檬酸(CA)为络合剂采用浸渍法制备了Ni2P负载的TiO2-Al2O3复合载体催化剂,并用X射线衍射(XRD)、N2吸附比表面积测定、H2程序升温氢还原(H2-TPR)、程序升温氧化(TPO)、X射线光电子能谱(XPS)技术对催化剂的结构和性质进行了表征,考察了CA/Ni摩尔比对在Ni2P/TiO2-Al2O3催化剂上进行的二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响.结果表明:适量的CA可以丰富催化剂的孔道,提高催化剂的比表面积.当n(CA)/n(Ni)=2:1时,催化剂的比表面积达到126.75m2·g-1,与不加CA时相比,提高了57.05m2·g-1.调节n(CA)/n(Ni)能够改善活性相的分布,改变活性相的种类;引入CA使Ni和P前驱体的还原温度明显降低,促进活性相Ni2P的生成,一定程度上能够抑制催化剂表面炭的形成和沉积,提高其稳定性.n(CA)/n(Ni)=2:1时,催化剂具有最好的加氢脱硫活性,在360°C,3.0MPa,氢油比为500(V/V),液时体积空速为2.0h-1的条件下,二苯并噻吩转化率为99.5%,可将模拟油中硫含量由2%(w)降低到0.01%(w).     

浆态床中Cu/ZnO/Al2O3/ZrO2+γ-Al2O3双功能催化剂一步法合成二甲醚

采用共沉淀法,制备了纤维状CD501甲醇合成催化剂,采用SEM、TEM、XRD和BET等手段对催化剂进行了表征;并将其进一步和γ-Al₂O₃进行混合,获得了Cu/ZnO/Al₂O₃/ZrO₂+γ-Al₂O₃双功能催化剂,考察了其在浆态床中一步法合成二甲醚过程的催化特性。结果表明,相比商业催化剂(COM)和LP201催化剂,新型的CD501催化剂具有更大的比表面积和Cu/Zn分散性。对于浆态床中一步法合成二甲醚过程,采用CD501与γ-Al₂O₃双功能催化剂,相比采用COM或LP201与γ-Al₂O₃双功能催化剂,CO转化率提高了一倍,且经过270h测试,CO转化率从61%降至57%,二甲醚时空产率从0.54g/(g·h)降至0.48g/(g·h),稳定性显著优于COM催化剂。当反应温度为250℃,压力为4.0MPa,空速为3000mL/(g·h),氢碳比为1.0时,该催化剂应用在浆态床一步法合成二甲醚时,CO转化率为61%,DME时空产率达到0.54g/(g·h)。     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

BaTiO3-BaAl2O4-Al2O3复合载体的制备、表征及其Ni基催化剂催化CH4/CO2重整反应性能

以十六烷基三甲基溴化胺为结构导向剂,采用溶胶-凝胶法制备了BaTiO3-BaAl2O4-Al2O3复合载体,采用X射线衍射、红外光谱、N2吸附-脱附、透射电子显微镜和H2程序升温还原等技术对复合载体进行了表征,并以CH4/CO2重整制合成气为探针反应,考察了不同Ni/BaTiO3-BaAl2O4-Al2O3催化剂的性能.结果表明,BaTiO3-BaAl2O4-Al2O3复合载体具有多孔织构特性和较高的比表面积,BaTiO3和BaAl2O4以晶粒状态分布在复合载体的内外表面,晶粒尺寸在20～50nm的范围,复合载体孔径为10～20nm.复合载体上BaTiO3和BaAl2O4的引入,适度削弱了Ni/BaTiO3-BaAl2O4-Al2O3催化剂中Ni物种与γ-Al2O3间的强相互作用,抑止了NiAl2O4尖晶石的生成;当载体中Ba(Ti)含量为17.33%时,其负载的Ni催化剂上CH4/CO2重整制合成气反应的活性和稳定性最高.