聚氨酯脲-丙烯酸酯水分散液的粒径及形态研究

研究了羧基含量、异氰酸酯指数（［ － ＮＣＯ］／［ － ＯＨ］） 、聚氨酯脲与聚丙烯酸酯组成比（ＰＵＵ／ＰＡ） 以及一系列制备工艺因素对聚氨酯脲—丙烯酸酯（ＰＵＡ） 水分散液粒子尺寸及形态的影响。结果表明：羧基含量和ＰＵＵ／ＰＡ 组成比增大或异氰酸酯指数减小都会导致分散液粒径减小;ＰＵＡ 中ＰＡ 含量越大,ＰＵＡ 水分散液粒子形态越不规整;工艺因素如搅拌强度、升温速率等对ＰＵＡ 水分散液粒子尺寸及形态的影响不符合传统乳液聚合的规律。     

偶联剂对丙烯酸酯改性聚氨酯聚合物接枝率和乳液性能的影响

合成了含双羟基的甲基丙烯酸甘油酯(GM)并将其作为偶联剂用于聚丙烯酸酯(PAC)对水基聚氨酯(PU)的改性.采用核磁共振、红外光谱和气相色谱等对GM进行了表征.分别以该双羟基GM和单羟基的丙烯酸羟乙酯(HEA)与异氰酸酯基(NCO)封端的PU预聚体进行反应以在PU分子链上引入双键,然后再与丙烯酸酯类单体通过自由基聚合制...     

四甲基苯二甲基二异氰酸酯基水性聚氨酯的合成和性能

采用四甲基苯二甲基二异氰酸酯、聚酯二元醇和二羟甲基丙酸为原料,合成了一系列具有不同异氰酸根与羟基摩尔比（n(-NCO)/n(-OH)）的聚氨酯乳液。 研究了n(-NCO)/n(-OH)对水性聚氨酯性能的影响。 结果表明,当该比值增加时,乳液的粒径增大,分布变宽,结晶性降低,耐热性下降,耐水性能呈现降低的趋势。 当异氰酸根与羟基摩尔比为3时,四甲基苯二甲基二异氰酸酯基水性聚氨酯的乳液粒径为10～30 nm,膜的分解温度达到275 ℃,24 h吸水率低于10%。     

聚氨酯/聚苯乙烯互穿聚合物网络的研究

互穿聚合物网络形态和力学性能的研究已有报道^[1～3],但有关合成过程中分子量变化形态和性能的影响研究甚少。本文在动力学研究的基础上^[4],用GPC、DSC和Instron万能机研究了聚氨酯/聚苯乙烯互穿聚合物网络(PU/PSt-IPN)的分子量,玻璃化转变温度和力能,考察了分子量与相分离点之间的关系。     

Preparation of Aqueous Polyurethane Dispersions Using Aromatic Diisocyanate

Aqueous polyurethane dispersions were prepared by the reaction of hydroxyl-terminated poly(ethylene adipate), ethylene glycol, dimethylol propionic acid and aromaic diisocyante, 4,4′-diphenylmethane diisocyanate. The influence of molecular weight of oligoester and molar ratio between isocyanate and hydroxyl groups (NCO/OH) in the prepolymerization step were investigated. Molecular weight, particle size and particle size distribution were measured and compared. It was verified that the molecular weight increases with increasing in NCO/OH molar ratio. The results suggest that the hard segment content plays an important role in particle size and particle size distribution of the dispersions.     

Synthesis and properties of room temperature curable trimethoxysilane‐terminated polyurethane and their dispersions

The purpose of this research is to study the synthesis and characterization of stable aqueous dispersions of externally chain extended polyurethane/urea compositions terminated by hydrolyzable or hydrolyzed trialkoxysilane groups incorporated through secondary amino groups. These dispersions with excellent storage stability are substantially free from organic solvents which cure to water and solvent resistant, tough, scratch resistant, preferably light stable (non‐yellowing) silylated polyurethane (SPU) films. The films were characterized by FT‐IR, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile strength and water contact angle measurements, nanoindentation, gel content, water and xylene swellability tests. The properties of the films were discussed and correlated in detail by changing length of soft segment, diisocyanates, NCO/OH ratio and chain extender, ethylenediamine (EDA). From the results, it was found that the particle size and viscosity are lower whereas the gel content and thermal stability are higher for SPUs. Modulus, hardness and tensile properties of SPU films are superior compared to EDA‐PU film. Higher water contact angle and residual weight percentage of SPU films confirm silylation of PU by [3‐(phenylamino)propyl]trimethoxysilane (PAPTMS). Increase in NCO/OH ratios consumes more quantity of PAPTMS which makes PU with superior mechanical properties. Higher PAPTMS content in SPU results in effective crosslinking of the functional silanol groups formed by hydrolysis reaction of trimethoxysilane groups. Overall, SPUs synthesized at 1.4 NCO/OH ratio using Poly‐(oxytetramethylene)glycol (PTMG)‐2000 and isophorone diisocyanate (or) toluene‐2,4‐diisocyanate have excellent properties compared to SPUs prepared using PTMG‐1000 and at 1.2 and 1.6 NCO/OH ratios. SPUs prepared at 1.6 NCO/OH ratio are brittle due to higher crosslinking density. In addition, the crosslinking density of the films can be modified through silane end‐group modification to produce SPUs with a wide range of physical properties. Copyright © 2007 John Wiley & Sons, Ltd.     

Interpenetrating polymer network from castor oil-based polyurethanes and poly(methyl methacrylate). XV

The polyurethanes have been prepared from 2.12 functional ? OH containing castor oil and diphenyl methane diisocyanate under identical experimental conditions with a varying NCO/OH ratio. These polyurethanes were swollen in methyl methacrylate and subsequently interpenetrated by free radical polymerization using benzoyl peroxide and crosslinker ethylene glycol dimethacrylate. A series of interpenetrating polymer network (IPN) PU/PMMA IPNs were obtained as films by a transfer moulding technique. These IPNs were characterized by their resistance to chemical reagents, thermal behavior, and mechanical properties. The morphology was shown by SEM and dielectric properties at different temperatures were measured.     

聚醚聚氨酯/环氧树脂互穿网络聚合物的研究(Ⅱ)

合成了不同类型聚醚聚氨酯/环氧树脂(PU/EP)互穿网络聚合物(IPN),通过改变PU中聚乙二醇分子量、3OH/2OH及NCO/OH比值等,研究IPN组份间分子混合程度,采用电镜、动态力学分析及应力应变等测试方法表征。结果表明:聚乙二醇分子量降低及3OH/2OH、NCO/OH比的提高,可使相容性提高,材料力学性能增强。     

超浓乳液聚合制备PU/PS的SIPN粉状树脂研究

将聚氨酯予聚体 (PU ) 苯乙烯 (St)的复合体系 ,用超浓乳液聚合方法制备了半互穿聚合物网络(SIPN)复合聚合物 ,得到了用聚氨酯予聚体改性的聚苯乙烯 (PU/PS)SIPN粉状树脂 .研究了分散相的比例(α)和聚合温度对聚合稳定性及聚合转化率 -时间的关系 ;测定了聚合物胶乳粒子的大小、形态 ,玻璃化温度 ,动态力学性能等 .结果表明 ,超浓乳液聚合较之本体聚合具有较高的聚合速率 ,容易控制所制备的胶乳粒径 ,能够制得PU/PS复合聚合物的SIPN粉状树脂 .该粉状树脂便于加工 ,具有良好的强韧性 ,有利于扩大应用     

Preparation of polyurethane dispersions by miniemulsion polymerization

With a two‐step miniemulsion polymerization, hydrophobic polyurethane (PU) dispersions were prepared with a cosurfactant, the costabilizer hexadecane (HD) in the oil phase, and sodium dodecyl sulfate (SDS) in the water phase. The first step involved the formation of NCO‐terminated prepolymers between isophorone diisocyanate and poly(propylene glycol) oligomer in toluene. Next, PU dispersions were produced by a miniemulsion method in which an oil phase containing NCO‐terminated prepolymers, HD, the chain extender 1,4‐butanediol (BD), the crosslinking agent trimethylol propane (TMP), and the catalyst dibutyltin dilaurate was dispersed in the water phase containing SDS. The influence of experimental parameters, such as the ultrasonication time, concentrations of SDS and HD, and TMP/BD and NCO/OH equivalent ratios, on the sizes of the miniemulsion droplets and polymer particles, as well as the molecular weights and thermal properties of the PU polymer, was examined. The chemical structure of the produced PU polymer was identified with a Fourier transform infrared spectrometer. The molecular weight distribution and average particle size were measured through gel permeation chromatography and dynamic light scattering, respectively. The thermal stability of the PU polymer was characterized with thermogravimetric analysis. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4870–4881, 2005     

聚丙烯酸酯改性水性聚氨酯的制备

在回顾聚丙烯酸酯改性水性聚氨酯的研究历史基础上，系统地介绍了聚丙烯酸酯改性水性聚氨酯乳液（PUA）的制备方法，其中包括聚氨酯（PU）和聚丙烯酯（PA）的直接掺混法、PU和PA的乳液共聚法，接枝法，互穿网络法，核壳聚合法，对这些方法做了简单的评述，对其应用范围及前景进行了初步探讨。     

Modification of aqueous polyurethanes by forming latex interpenetrating polymer networks with polystyrene

A series of latex particles with interpenetrating polymer network structure have been synthesized from waterborne polyurethane (PU) and polystyrene (PS). The effect of PU/PS composition, cross-linking density in the PS domain as well as in PU have been studied in terms of dispersion size, transmission electron microscopy morphology, mechanical and dynamic mechanical properties in addition to swellability in water and toluene of the dispersion cast film. It was found that inverted core (PS)–shell (PU) morphology was well defined and that the domain size as well as the film properties were well controlled by the latex composition and cross-linking density of both phases. Received: 15 March 2000 Accepted: 21 February 2001     

Interpenetrating polymer networks from polyurethanes and methacrylate polymers. I. Effect of molecular weight of polyols and NCO/OH ratio of urethane prepolymers on properties and morphology of IPNs

Two types of reinforced elastomeric interpentrating polymer network (IPN) were prepared by simultaneous polymerization and crosslinking in solution. The first type consisted of polyurethane-poly(methyl methacrylate) (PU/PMMA), and the second, of polyurethane-poly(methyl methacrylate-methacrylic acid) PU/P(MMA–MAA) of constant composition (90/10) and (80/20) by weight, respectively. The members of each type differed in the NCO/OH ratio of the PU prepolymer and the molecular weight (MW) of the polyol in the PU component because we wished to investigate systematically the effect of changing the NCO/OH ratio and MW of the polyol on the mechanical properties and morphology of the resulting IPNs. The mechanical properties, particularly the modulus of both tyes of IPN, increased with increasing NCO/OH ratio and decreased with increasing MW of the polyol in the PU. The morphology of the IPNs was studied by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Improved phase compatibility and decreasing extent of phase separation was observed in both types of IPN with increasing NCO/OH ratio and decreasing MW of the polyol used in the PU. These results may imply that improved interpenetration results from increasing the NCO/OH ratio and decreasing the MW of the polyol in the PU component. The fact that the effect is more pronounced with the type of PU-P(MMA–MAA) IPN can be rationalized as due to the additional hydrogen bonding between the carbonyl in the carboxyl groups and the urethane or urea groups in the PU component.     

Influence of structure-property relationship on the optical,thermal and mechanical properties of castor oil based transparent polyurethane for catheter applications

Castor oil based transparent polyurethane elastomers were synthesized, which can be used as an advanced catheter material. The effect of NCO: OH ratio on the structural, optical, thermal and physicomechanical properties of polyurethanes (PU) has been studied. The optical properties of the PU was analysed by studying its percentage transmittance and haze. The results showed a high transparency of 90.7% for the PU with a NCO: OH ratio of 0.9:1. Differential scanning calorimetry (DSC) analysis revealed an increase in the glass transition temperature (T_g) of PU with increasing hard segment content whereas thermogravimetric analysis (TGA) shows an increase in the initial decomposition temperature of PU from 262 to 268°C upon increasing the NCO: OH ratio from 0.9 to 1.5. A similar trend of increment in the tensile properties of PU has been observed as a consequence of increasing the molar ratio of NCO: OH. In vitro cytotoxicity analysis of PU was studied using human embryonic kidney (HEK293) cell line that revealed the nontoxic character of PU.     

P(VA-co-DBM)/PVA乳胶IPN阻尼材料的合成及动态力学性能

用种子乳液聚合法合成了聚（醋酸乙烯酯－co-马来酸二丁酯）／聚醋酸乙烯酯乳胶互穿聚合物网络阻尼材料,动态力学谱结果表明,该阻尼材料在较宽的温域具有很高的阻尼因子。     

Miniemulsion copolymerization of vinyl acetate and butyl acrylate. I. Differences between the miniemulsion copolymerization and the emulsion copolymerization processes

Differences between the emulsion copolymerization and miniemulsion copolymerization processes, in terms of emulsifier adsorption, emulsion stability, polymerization kinetics, copolymer composition and dynamic mechanical properties were studied for the comonomer mixture of 50:50 molar ratio vinyl acetate (VA+)—butyl acrylate (BuA), using sodium hexadecyl sulfate (SHS) as a surfactant and hexadecane (HD) as a co-surfactant. The use of hexadecane with the appropriate SHS initial concentration led to a higher adsorption of surfactant, smaller droplet size, higher stability of the emulsions, lower polymerization rates, and larger latex particle size. The copolymer composition during the initial 70% conversion was found to be less rich in Vac monomer units for the miniemulsion process. The dynamic mechanical properties of the copolymer films showed less mixing between the BuA-rich core and the VAc-rich shell in the miniemulsion latexes compared to the conventional latex films.     

Thickening of Crosslinked Ethyl Methacrylate-Acrylic Acid Latexes

Latexes based on ethyl methacrylate (EMA), acrylic acid (AA), crosslinked with 1,6-hexanediol propoxylate diacrylate (HPDA), were synthesized via emulsion polymerization, yielding dispersions with different acidic group contents and crosslinking densities. The latexes were thickened using various NaOH/AA molar ratios and the resultant dispersions were characterized by pH-metry, zeta potentiometry, and turbidimetry. The process of thickening by carboxyl neutralization was shown to be dependent on the neutralization effect on particle–particle interactions and particle solubilization. Turbidimetry, pH-metry, and zeta potential measurements showed that neutralization resulted in partial latex solubilization and viscometry indicated that, for a given latex, an optimum thickening was achieved for and specific NaOH/AA molar ratio, showing the existence of a relationship between thickening, particle–particle interactions, latex solubilization, and polyelectrolyte effect.     

Poly(2-acetoxyethyl methacrylate)/polystyrene latex interpenetrating polymer networks with well-defined phase-separated structure

A series of poly(2-acetoxyethyl methacrylate)/polystyrene(PAEMA/PS) latex interpenetrating polymer networks(LIPNs) were prepared by seeded soap-free emulsion polymerization of styrene on the crosslinked PAEMA seed particles using an oil-soluble initiator.These PAEMA/PS LIPNs showed a well-defined phase-separated structure with PS phase dispersing in continuous PAEMA phase.The domain size of PS phase was found to depend on the crosslinking degree of PAEMA seed particles and the amount of second-stage styrene monomer.     

Synthesis,morphology, and properties of waterborne m-TMXDI-based anionic polyurethane and hybrids

In this study, waterborne polyurethane (WPU) hybrid emulsions with a weight ratio of 2/1 were prepared by emulsion polymerization using a mixture of styrene (St) and/or butyl acrylate (BA) monomers with WPU dispersion. WPU dispersion was synthesized with isocyanic acid and m-tetramethylxylene diisocyanate (m-TMXDI)-based anionic poly(urethane-urea) dispersions using the prepolymer mixing process. The structures of WPU and hybrids were characterized by FTIR spectroscopy. The size and morphology of the latex particles were investigated using dynamic light scattering and transmission electron microscopy, respectively. The stability of the emulsions was determined according to their shelf life and particle size using the dispersion analyser LUMiSizer® with STEP?-Technology. The thermal and mechanical properties of these films were examined by thermogravimetric analysis and strain-stress curves.     

聚氨酯/环氧树脂互穿网络聚合物的性能研究

互穿聚合物网络（Interpenetrating polymer net-work,简称IPN）广泛应用的为聚氨酯基的互穿网络聚合物。其合成多集中在弹性体方面。本文用同步法合成的聚氨酯／环氧树脂互穿网络硬质泡沫塑料材料（简称PU／ERIPNF）,机械性能较好,并研究了其动态力学性能及形态变化。