Degradation of sulfadiazine antibiotics by water falling film dielectric barrier discharge

A new water falling film dielectric barrier discharge was applied to the degradation of sulfadiazine in the aqueous solution. The various parameters that affect the degradation of sulfadiazine and the proposed evolutionary process were investigated. The results indicated that the inner concentrations of 10 mg/L sulfadiazine can be all removed within 30 min. The optimum pH value was 9.10 and both strong acidic and alkaline solution conditions were not suitable for the degradation. The degradation of sulfadiazine can be enhanced by the addition of hydrogen radical scavengers, but be inhibited by adding hydroxyl radical scavengers. The water falling film dielectric barrier discharge was rather ineffective in mineralization, because of the intermediates were recalcitrant to be degraded. The existence of Fe2+and CCl4 in the liquid phase can promote the degradation and mineralization of sulfadiazine. It was found that the degradation of SDZ was enhanced by CCl4 was mainly because of the increase of OH due to the reaction of CCl4 with H that reduce the chances of their recombination with OH. Based on the 8 intermediate products identified by LC–MS, the proposed evolution of the degradation process was investigated.     

Spectroscopic characterization of mechanisms of oxidation of Phe by SO_4~- radical: A pulse radiolysis study

By using time-resolved kinetic spectrophotometry and pulse radiolysis technique, the oxidation of Phe by SO4- radical has been investigated both in aqueous and water/acetonitrilemixed solutions. The results reveal that attack of the oxidizing SO4- radical on Phe leads directlyto the formation of Phe cation radical 3 with a strong absorption peak at 310 nm, then it proceeds in three competitive reactions via either hydroxylation, deprotonation or decarboxylation, which were found to be strongly dependent upon the ionization state of the substitutes -COOH and -NH2 and the nature of the solvents. Decarboxylation takes place only when the carboxyl group is deprotonated. At high pH deprotonation of Phe cation radical 3 is much easier to occur than that in neutral or acid solutions. Moreover, with addition of acetonitrile, deprotonation is more predominant than hydroxylation, whereas in aqueous solutions hydroxylation is much easier to occur.     

等离子体条件Cu/SiO2对甲烷偶联的催化作用

It has been reported that methane coupling by plasma techniques with catalysts, such as direct current corona discharge with a Sr/La2O3 catalyst[1], dielectric-barrier discharge with zeolites[2] and pulsed corona discharge with metal oxide catalysts[3], give C2 hydrocarbons under atmospheric pressure. But acetylene predominates over other C2 hydrocarbons in the products. Our recent work reported that good results can be obtained for methane coupling under a pulsed corona plasma in the presence of hydrogen[4]. The addition of hydrogen improves the conversion of methane and the yield of C2 hydrocarbons. A methane conversion of 57.1% and a yield of C2 hydrocarbons of 43.4% were obtained at lower power, but acetylene was inevitably the main product. With the introduction of a Ni/γ-Al2O3 catalyst prepared by a cold plasma into the plasma reaction, the distribution of C2 hydrocarbons changed, and the content of C2H4 was 66.1%[5].     

EFFECT OF WATER ON THE OXIDATION OF METHANOL OVER ELECTROLYTIC SILVER

The mechanism of methanol adsorption induced by oxygen and the effect of water on the methanol oxidation on electrolytic silver have been studied by ultra-high vacuum temperature programmed reaction spectroscopy(TPRS), transient response method and isotopic exchange experiment. It has been found that oxygen adsorbed on silver can greatly promote methanol adsorption and can also react with methanol to produce water. Experimental results show that oxygen in the water comes from the adsorbed oxygen and hydrogen from the methyl and the hydroxyl in methanol. It has also been found that there exists competitive adsorption between water and oxygen on silver and water can increase the selectivity of methanol oxidation to formaldehyde. This result is consistent with the catalytic activities.     

Theoretical Study on the Photodegradation Mechanism of Pyrethroid Insecticide Fenvalerate in Water

The photodegradation mechanism of fenvalerate in water has been investigated by density functional theory(DFT).The geometries of reactants,transition states,intermediates and products are optimized at the B3LYP/6-31G* level.The calculated results indicate that the reaction process mainly includes the nucleophilic attack and the substitution reaction by hydroxyl radical to the carbonyl group.By vibrational frequency analysis and intrinsic reaction coordinate(IRC) method,the transition state and its reaction pathway are confirmed.Moreover,the changes of natural population analysis(NPA),calculated using the Natural bond orbital(NBO) method,are analyzed along with the degradation reaction which can explain the variation of chemical bonds.Additionally,the solvent effect is also investigated and the results show that the reaction preferably takes place in water.     

Systhesis of double-hydrophilic core-shell type multiarm star copolymer polyethylenimine-block-poly(2-hydroxyethyl methacrylate

Multiarm star block copolymers hyperbranched polyethylenimine-b-poly(2-hydroxyethyl methacrylate) (HPEI-b-PHEMA) with average 28 PHEMA arms have been prepared by atom transfer radical polymerization (ATRP) of HEMA in a mixed solvent of methanol and water using a core-first strategy. The hyperbranched macroinitiator employed was prepared on the basis of well-defined hyperbranched polyethylenimine with Mw/Mn of 1.04 by amidation with 2-bromo-isobutyryl bromide. The polymerization condition was optimized to prepare star copolymers with narrow dispersity, and the variables included the volume ratio of methanol to water, the molar ratio of initiating site to CuCl and the molar ratio of [CuCl]:[CuBr2]. Under the optimized polymerization condition, the lowest Mw/Mn value of the obtained star copolymers was around 1.3. Kinetic analysis showed that an induction period existed in the polymerization of HEMA. After this induction period, a linear dependence of ln([M]0/[M]t) on time was observed. The obtained HPEI-b-PHEMA could adsorb hydrophilic molecules. The comparison with the star copolymer with hydrophobic core and hydrophilic PHEMA shell verified that both the hydrophilic core and shell could host the hydrophilic guests, but the amidated HPEI core was more effective than the PHEMA shell.     

Pulse radiolysis study on gatifloxacin——A fluoroquinolone antibiotic

The reactions between gatifloxacin(GFX) and various one-electron oxidants,such as ˙OH,N3˙,Br2˙ˉ,and SO4˙ˉ,have been studied by pulse radiolysis techniques.The GFX radical anion formed in the reaction of GFX with eaqˉ could either be protonated or deprotonated,and the absorption of GFX radical anion was located at 390 nm.The transient species produced by the reaction of GFX with ˙OH radical shows a broad band in the 380?600 nm region with a shoulder,while the oxidation by N3˙,SO4˙ˉ,and Br2˙ˉ results in an absorption band with λmax = 370 nm.At neutral condition(pH 7),the rate constants of GFX reacting with ˙OH,N3˙,Br2˙ˉ,SO4˙ˉ and eaqˉ are estimated to be 1.0 × 1010,3.1 × 109,2.8 × 109,3.0 × 109,and 1.8 × 1010 dm3 mol?1 s?1,respectively.From the pH dependence on the formation of electron adducts and on the rate constant of GFX with eaqˉ,the pKa of GFX radical anion is estimated to be 5.5 and 9.3.     

Theoretical Study on Reactivity of Electron Transfer in Model—System of Oxidation of α—Amino Carbon—centered Radical by O2

Electron transfer reaction between a simplified model model molecule of α－amino carbon-centered radical and O2 has studied with ab initio calculations at the MP2/6-31 G^**//UHF/6-31 G^** level,The reactant complex and the ion pair complex have been optimized and employed to perform calculation of the reaction heat and the reorganization energy,Solvent effects have been considered by applyning the conductor-like screening model,Theoretical results show that the highly endothermic charge separation process ,in which one electron transfers from the α－amino carbon-centered radical to O2,so as to form an ion pair complex,is difficult to occur in gas-phase,By apply-ing an external electronic field to prepare the charge-locallized molecular orbitals,the charge-separated state has been obtained using the initial-guess-induced self-consistent field technique,The theoretical investigations indicate that the solvent effect in the process of the oxidation of α-animo carbon-centered radical by O2 is remarkable.From the rate constant estima-tion ,it can be predicted that the oxidation of the model donor molecule by O2 can proceed,but not very fast.A peroxyl radi-cal compound has been found to be a competitive intermediate in the oxidation process.     

Impact of Water Molecules on the Isomerization of CH3S（OH）CH2 to CH3S（O）CH3： A Computational Investigation

The isomerization of CH3S（OH）CH2 to CH3S（O）CH3 in the absence and presence of water has been investigated at the G3XMP2//B3LYP/6-311 ＋ G（2df, p） level. The naked isomerization, the reaction without water, gives the high barrier height （21.56 kcal.mol^-1）. Three models are constructed to describe the water influence on the isomerization, that is, water molecules are the catalyst and the microsolvation, and water molecules act as the catalyst and microsolvation simultaneously. Our results show that the isomerization barrier heights of CH3S（OH）CH2 to CH3S（O）CH3 are reduced by 12.32, 11.04, and 7.80 kcal.mol^-1, respectively, when one, two, and three water molecules are performed as catalyst, in contrast to the naked isomerization. Moreover, the rate constants of the isomerization are calculated using the transition state theory with the Wigner tunneling correction over the temperature range of 240-425 K. We find that the rate constant of a single water molecule as the catalyst is 1.58 times larger than the naked isomerization at 325 K, whereas it is slower by 6 orders of magnitude when water molecule serves as the microsolvation at 325 K, compared to naked reaction. So the water-catalyzed isomerization of CH3S（OH）CH2 to CH3S（O）CH3 is predicted to be the key role in lowering the activation energy. The isomerization involving water molecules acting as mierosolvation is unfavorable under atmospheric conditions.     

Distribution of Helium Isotopes in Western Pacific Upper Layer

3He/4He ratios in samples of sea water obtained at depths from surface to 300 m in the upper layer of the Western Pacific Ocean were measured by a mass spectrometer VG5400. The lateral and vertical distribution of He isotopes in the studied area was discussed in detail on the basis of 3He/4He ratios. Excess and depleted 3He. in relation to δ3He value of surface water in equilibrium with air has been discussed in the area, which may be mainly attributed to the incorporation of the North Pacific Intermediate Water with the Equatorial Upwelling and the exchange of water masses between the South China Sea and the Western Pacific, respectively. The present work in Western Pacific has also indicated that He isotopes may be used as a tracer for mixing processes of water masses and oceanic circulation.     

The efficacy of heating low-pressure H2 in a microwave discharge

The relative ease with which a low-pressure hydrogen stream may be heated in an electrical discharge suggests that such a system be considered in current efforts to develop thrusters for spacecraft orbit raising purposes. In this work a detailed model of a microwave discharge in flowing, low-pressure hydrogen is used to interpret and clarify experimental measurements of atom concentration, electron energy, and electron density. The radially averaged, constant-pressure model accurately reproduces the experimental data and also calculated the rates of a number of gas-heating and wall-heating processes as well as rates of energy deposition into coolant and working fluid streams. The calculated gas-heating rates indicate that the gas heating is due primarily to the thermalization of the energetic atoms produced by dissociation of H₂ via excitation of theb ³∑ _u ⁺ state. The calculations also indicate that the energy flux to the quartz tube is significantly influenced by Lyman and Werner band radiation and by heterogeneous atomic recombination processes and, to a much lesser degree, by electron-ion recombination processes. The fraction of power input which is ultimately transferred to the gas stream is a decreasing function of the power input and varies from 0.24 to 0.12.     

The design and characteristics of direct current glow discharge atomic emission source operated with plain and hollow cathodes

A compact direct current glow discharge atomic emission source has been designed and constructed for analytical applications. This atomic emission source works very efficiently at a low-input electrical power. The design has some features that make it distinct from that of the conventional Grimm glow discharge source. The peculiar cathode design offered greater flexibility on size and shape of the sample. As a result the source can be easily adopted to operate in Plain or Hollow Cathode configuration. I-V and spectroscopic characteristics of the source were compared while operating it with plain and hollow copper cathodes. It was observed that with hollow cathode, the source can be operated at a less input power and generates greater Cu I and Cu II line intensities. Also, the intensity of Cu II line rise faster than Cu I line with argon pressure for both cathodes. But the influence of pressure on Cu II lines was more significant when the source is operated with hollow cathode.     

Pulsed discharge detector: theory and applications

The pulsed discharge detector (PDD) is a significant advancement in gas chromatography (GC) detector design which can be operated in three different modes: pulsed discharge helium ionization (He-PDPID), pulsed discharge electron capture (PDECD) and helium ionization emission (PDED). The He-PDPID can detect permanent gases, volatile inorganics and other compounds which give little or no response with the flame ionization detector (FID) and has significantly better limits of detection (minimum detectable quantities (MDQs) in low picogram range) than can be achieved with a thermal conductivity detector (typically not lower than 1 ng). The PDECD has similar or better sensitivity (MDQs of 10(-15) to 10(-12) g) than radioactive source ECD but does not require licensing, wipe tests and other administrative or safety requirements which have increased over security concerns. The PDED shows promise as an extremely selective and sensitive elemental detector but a commercial unit is not presently available. In this report, the theory of operation, applications of the PDD and the practical aspects of using this novel detector are presented.     

Preparation of electrodeless discharge lamps for emission studies of uranium isotopes at trace level

A simplified method for preparation of electrodeless discharge lamp for uranium isotopes with specific concerns for ²³²U is described. Micro-gram quantities of solid uranium oxides and aqueous solution of uranium nitrate have been used as a starting material for in situ synthesis of uranium tetraiodide. High temperature iodination reaction is carried out in the presence of inert gas neon. By careful design, the preparation time and surface area of quartz reaction tubes have been reduced considerably. The latter decreases the level of contamination which has a direct bearing on the operational lifetime of the lamps. Incorporation of steps to purify the product from an unwanted material improved the stability of the lamps. The procedure provides a safe and convenient way of handling ²³²U in particular but can be extended in general to any actinides having radioactivity similar to that of freshly separated ²³²U. Characteristic emission of uranium isotopes have been recorded by Fourier Transform Spectrometer to show the satisfactory operation of the lamps as well as their usage for studying emission spectra of the specific isotope.     

Direct Non-oxidative Methane Conversion by Non-thermal Plasma: Experimental Study

The direct non-oxidative conversion of methane to higher hydrocarbons in non-thermal plasma, namely dielectric barrier discharge and corona discharge, has been investigated experimentally at atmospheric pressure. In dielectric barrier discharge, the methane is mainly converted to ethane and propane with small amounts of unsaturated and higher hydrocarbons. While in corona discharge, methane was activated mainly to acetylene with small amount of other higher hydrocarbons. Decreasing the gas flow or increasing power input will improve the methane conversion and product yields. It is found that the methane conversion and main product yield against the input specific energy were special functions in both dielectric barrier discharge and corona discharge, independent of the reactor size, and whether fixing flow rate or power input and changing the power input or flow rate. The corona discharge is a promising alternative method for methane conversion to produce acetylene and hydrogen at low temperature.     

Comparison Between Air Filamentary and Helium Glow Dielectric Barrier Discharges for the Polypropylene Surface Treatment

Recently, a glow like dielectric controlled barrier discharge (GDBD) working at atmospheric pressure has been observed. Such a discharge could replace a filamentary dielectric controlled barrier discharge (FDBD) used in corona treatment systems to improve the wettability or the adhesion of polymers. So it is of interest to compare these two types of discharges and their respective effect on a polymer surface. This is the aim of an extensive study we have undertaken. The first step presented here is the comparison of a filamentary discharge in air with a glow discharge in helium. Helium is the most appropriate gas to realize a glow discharge at atmospheric pressure. Air is the usual atmosphere for a corona treatment. The plasma was characterized by emission spectroscopy and current measurements. The surface transformations were indicated by the water contact angle, the leakage current measurement and the X-ray photoelectron spectroscopy. Results show that the helium GDBD is better than air FDBD to increase polypropylene wettability without decreasing the bulk electrical properties below a certain level. Contact angle scattering as well as leakage current measurements confirm that the GDBD clearly results in more reproducible and homogeneous treatment than the FDBD.     

PbO~2纳米粉体的固相合成及其对MnO~2电极材料的改性作用

利用固相氧化反应制备了PbO~2纳米粉体样品，借助XRD，TEM以及循环伏安测试对其性质进行了表征。同时，对反应条件的选择进行了讨论。将所得样品用于改性MnO~2电极，恒流放电测试结果表明，样品掺杂量在1.25%～5.00%间对MnO~2有良好的改性效果，可使改性MnO~2的放电容量得到极大提高。循环伏安测试结果表明，铅的掺入改变了MnO~2的放电机理。在循环扫描过程中，掺杂物与MnO~2均不再以单纯氧化物的形式存在，而是形成了一系列Pb(X)(X=0,Ⅱ)Mn(Y)(Y=Ⅳ，Ⅲ，Ⅱ)复合物的共氧化与共还原，抑制了电化学惰性物质Mn~3O~4的生成和积累，从而有望改善MnO~2的可充性能。纳米PbO~2与常粒径PbO~2与常粒径PbO~2(标记为S)对MnO~2的改性机理类似。但前者对MnO~2的改性效果明显优于后者，当恒流放电至-1.0V时，其放电容量较S样改性MnO~2的放电容量平均高出约30%。     

Electric discharge-induced oxidation of hydrogen cyanide

The AC high-voltage discharge-induced decomposition chemistry of trace levels of hydrogen cyanide in helium has been studied. In the absence of oxygen only low levels of molecular nitrogen were evolved. With oxygen added, the principal products were CO, CO₂, and N₂. No significant concentrations of NO or N₂O were observed. The response of a commercial NO_x analyzer to HCN and C₂N₂, in the NO_x mode, was determined to be linear through three decades in concentration. The oxidation chemistry of HCN and C₂N₂ in the stainless steel converter of the analyzer was studied as a function of the amount of added oxygen.NRL/NRC Postdoctoral Fellow (1983–1985).     

基于定向纳米碳管气体放电的气敏传感器研究

介绍了一种基于定向纳米碳管的气敏传感器,以生长定向纳米碳管的氧化铝模板作为阳极,铝板作为阴极,利用纳米碳管的尖端发射效应,在较低的电压下使气体产生放电现象。通过对纳米碳管在气体中击穿电压和放电电流的测量,实现对气体的定性定量检测。同时纳米碳管气敏传感器还具有体积小、灵敏度高、稳定性好、响应速度快、在常温常压下即可进行检测等优点,具有较好的应用前景。     

非平衡等离子体放电模式及反应器结构对氨气分解制氢的影响

在常压下研究了不同等离子体放电模式及反应器结构对氨分解制氢反应的影响.实验中调节反应器结构分别产生了介质阻挡放电和交流弧放电两种放电模式.通过对两种放电模式的放电图像、电压-电流波形和氨分解过程中等离子体区活性物种的发射光谱(OES)研究发现,与介质阻挡放电相比,交流弧放电为局部强放电,具有更高的电源效率和电子密度.因此,在介质阻挡放电中氨气分子大部分通过生成电子激发态物种NH3*,再与载能电子碰撞断裂N―H键进行氨分解反应;而在交流弧放电中载能电子具有更高的平均电子能量,可直接断裂氨气分子的N―H键生成NH2和NH等高活性物种,促进氨分解反应的进行.结果表明,交流弧放电的氨分解效果要明显优于介质阻挡放电.在交流弧放电模式下不同类型反应器对氨气分解转化率由高到低的顺序为:管-管管-板针-板板-板.在输入功率为30 W,气隙间距为6 mm时,管-管交流弧放电的氨气转化率达到60%左右,而板-板介质阻挡放电的氨气转化率仅为4%.