室温下镀钯多壁碳纳米管对苯的气敏响应特性

在酸氧化后的多壁碳纳米管上化学还原镀钯,用水将镀钯后的碳管清洗至中性并配制成悬浊液,将悬浊液旋涂在真空溅射的叉指金电极表面,干燥后作为气敏膜,把气敏膜暴露于一定浓度的苯气体中,检测传感器的电流变化,并计算其灵敏度。镀钯后的多壁碳管在室温下对苯响应和回复迅速,电导变化与苯气体的浓度呈良好的线性关系,其线性回归方程y=0.0041x 0.1288,r=0.9546。Pd颗粒对苯分子和碳管壁结构缺陷间的电子转移的促进作用可能是多壁碳管镀钯后产生良好气敏响应的原因。     

钼酸铋基气敏材料研究进展

气体传感器被广泛应用于检测工业和家庭中有毒有害气体。气体敏感材料是气体传感器中重要的组成部分,敏感材料的性质决定了气体传感器的性能。研制精度高、检测快、集成度高的气体检测器迫在眉睫。钼酸铋作为一种新型双金属氧化物气敏材料,具有高选择性、高敏感度的优势。本文从气敏机理、形貌控制、掺杂和复合材料构建方面对近年来钼酸铋作为气敏材料的研究进行了总结,并对钼酸铋基气敏材料未来的研究方向进行了展望。     

WO3基气敏传感器*

气敏传感器已在生物、化学、航空、军事等领域获得了广泛的应用。鉴于WO₃基气敏传感器是检测H₂S、NO_x、O₃和NH₃等气体最有前景的新型氧化物气敏传感器之一,本文以不同的敏感气体为分类依据系统阐述了近年来WO₃基气敏传感器的研究进展,详细探讨了制备方法及贵金属掺杂对上述各种气体气敏性能的影响,并指出了目前WO₃基气敏传感器在研究过程中存在的问题。     

基于ZIF-8/PAN复合薄膜的柔性丙酮气体传感器

ZIF-8是一种Zn基金属有机骨架材料, 可以吸附丙酮气体从而作为电容式丙酮传感器的气敏材料, 然而ZIF-8的传统使用形式为粉末态, 这导致其不能成为具备柔性的整体, 从而限制了传感器的柔性. 结合包埋种子和二次生长法将ZIF-8与纳米纤维结合成纤维型柔性材料, 并将其作为气敏层制备了柔性电容式丙酮气体传感器. 该传感器在9种常见挥发性有机化合物中表现出良好的选择性, 对250~2000 cm³/m³的丙酮气体具有灵敏的响应、良好的循环响应及长期稳定性. 值得注意的是该柔性传感器不仅在室温下进行传感, 而且在弯折180°的状态下对丙酮气体的响应值与不弯折(0°)状态下几乎一致, 在200次以内的180°弯折-恢复后同样表现出了传感性能的稳定, 表明了其在柔性传感器方面的潜力.     

金属氧化物室温气敏材料的结构调控及传感机理

室温气敏材料能耗低、稳定性好、安全性高,并且有助于简化传感器的器件结构,具有很好的实际应用前景。开发具有优异室温传感性能的气敏材料成为近年来传感领域的研究热点。金属氧化物半导体材料来源广泛、环境友好、结构调控灵活,在室温气体传感性能方面取得一定的进展。本文介绍了金属氧化物气敏材料的发展历程及气体传感机理,详述了各种具有室温气敏性能的金属氧化物纳米结构,重点讨论构建金属氧化物室温传感性能的有效策略和传感机制,并对室温传感材料的未来发展进行了展望。     

单壁纳米碳管的纯化及表征

利用微孔膜及空气氧化法逐步除去电弧放电法制备的单壁纳米碳管(SWCNTs)中的金属催化剂粒子、碳纳米粒子、无定形碳等杂质,并利用热重分析（TGA）、高分辨透射电子显微镜（HRTEM）及拉曼（Raman）光谱,对每一步得到的产物进行分析表征.实验证明,该方法对单壁纳米碳管的纯化是比较有效的,可以得到纯度在90％以上的单壁纳米碳管.     

基于天然气敏材料猪肉中优势腐败菌的可视化检测

优势致腐菌是引起猪肉变质的重要原因之一,为了探索猪肉优势致腐菌绿色、快速的检测方法,本研究使用天然色素作为气体可视化传感器阵列的气敏材料,区分猪肉中的优势致腐菌。首先从植物中提取17种天然色素作为气敏材料,并将其固定在基底材料上,干燥后制成气体可视化传感器阵列。将3种优势致腐菌(梭状芽孢杆菌、热死环丝菌、假单胞菌)分别接种至3组猪肉样本中,在室温(20℃)条件下分别培养8、16和24 h,然后将传感器阵列与猪肉样本产生的挥发性物质接触并发生反应,用扫描仪获取传感器阵列与每个样本反应前后的图像信息,将传感器反应前后的颜色差值作为样本的特征值组成一个数据矩阵,并制成差值图像。最后采用主成分分析对培养8,16和24 h后的3种优势致腐菌进行检测,识别率分别为90%,90%和100%。结果表明,天然色素可以作为气体传感器的气敏材料,检测猪肉的优势致腐菌,且检测过程不会产生化学毒害。     

自偏压作用下纳米碳管的定向生长

以玻璃为基板材料, 在550 ℃的低温条件下利用微波等离子体化学气相沉积法合成了定向纳米碳管.结果表明, 在利用微波等离子体化学气相沉积法合成纳米碳管时, 因等离子体作用存在于基板表面的自偏压对纳米碳管的定向生长起着非常重要的作用.自偏压的作用总是使纳米碳管的生长垂直于基板表面.     

氧化铝模板上定向纳米碳管的快速生长及超声切短

在阳极氧化铝（AAO）模板上电沉积催化剂,快速生长了定向纳米碳管,纳米碳管以顶部生长模式生长.采用了超声的方法来切短露头于AAO模板的纳米碳管,增加纳米碳管膜的定向性.结果显示随着超声时间的增加,纳米碳管的定向性增加.位于纳米碳管膜顶部的催化剂在碳管切短的同时被去除,得到了顶部开口的纳米碳管.解释了纳米碳管被超声切短的机理.     

水热法制备MoO3-GQDs的三甲胺气敏性能

采用水热法制备了一系列具有不同碳量子点(GQDs)含量的MoO3?GQDs纳米复合材料,利用X射线衍射、扫描电子显微镜、透射电子显微镜、FTIR等对MoO3?GQDs复合材料进行了表征,研究了其气敏性能。结果表明,复合材料中GQDs的含量对MoO3?GQDs复合材料的气敏响应和选择性有显著影响。MoO3?GQDs纳米复合材料(S?6,GQDs悬浮液的含量为6 mL)传感器在230℃时对三甲胺(TMA)表现出高的气敏响应和好的气敏选择性;该传感器对1000μL·L^-1 TMA的响应为74.08;对1000μL·L^-1 TMA的响应时间和恢复时间分别为73和34 s;S?6复合材料气敏传感器在230℃时可以检测到1μL·L^-1的TMA。     

巴基管嵌锂电极性能的研究

用化学气相沉积法制备的巴基管作为锂离子电池的负极活性物质可以达到７００ｍＡｈ／ｇ的容量，远超过了石墨嵌锂化合物理论容量。ＣＶＤ巴基管电极经２０次充放电循环后，放电容量保持率为６５．３％，尽管ＣＶＤ巴基管电极初次充放电效率低，但经表面镀铜修饰后，初次充放电效率可提高到５５．９％。     

Influence of the anode material on the characteristics of an analytical glow discharge cell

The energy transfer to the discharge gas due to various collision processes in the plasma and the heating of the sample are widely known effects in glow discharge (GD) spectroscopy. Despite of the considerable thermal effects and their serious influence on the performance of GD devices, measurements of the discharge gas and sample temperatures are not common at all. The gas temperature depends on the power absorption of the discharge as well as on the temperature of boundaries (sample and anode). In this work the influence of different anode materials in a Grimm-type source on the voltage–current characteristics, crater shapes and GD spectra is investigated. Anodes made of titanium and copper alloys, graphite, and steel with thermal conductivities covering a wide range of values are used. For a fixed voltage and pressure a decrease of the measured current is observed for bad thermal conductive anodes. Cooling of the sample results in an increase of the measured current. Both observations can be explained by changes of the discharge gas temperature. The temperature of the sample is measured from the back side and compared for different anodes. Further, it is found that the choice of the anode material (i) has no significant influence on the crater shape, (ii) results in slightly different sputtering rates and (iii) strong differences of the GD spectra.     

氢气辅助的水中埋弧法制备小直径碳纳米管

用改进的石墨电弧放电方法制备了小直径、高质量的碳纳米管,以水为打弧介质,氢气为保护气体.该方法具有装置简单,电流小,无催化剂,制备出的多壁碳纳米管直径小于10 nm等优点.     

Development of an Atmospheric Pressure Glow Discharge Detector for Capillary Column Gas Chromatography

 The use of the change in the oscillation frequency of the current of a new atmospheric helium glow discharge for sensitive signal detection for gas chromatography is studied. The effluent of a capillary column is directed into the glow discharge cell perpendicular to the axis of the glow discharge that existed between a platinum anode and cathode. A stable discharge is obtained when several hundred volts are applied between the 0.2-mm gap between the anode and cathode. The effects of the electrode gap, discharge voltage and gas flow rate on the baseline frequency and discharge current were investigated. The chromatogram shows that the discharge current and discharge gap have a strong influence on the detector response. The discharge current shows positive peaks; however, frequency peaks are positive or negative depending on the discharge conditions. The response of the detector is in the femto-mole and pico-mole range for nonane and decane. Received August 5, 1997. Revision September 2, 1999     

基于水凝胶衍生的硅/碳纳米管/石墨烯纳米复合材料及储锂性能

通过氧化石墨烯(GO)和壳聚糖(Cs)之间的氢键以及静电作用形成GO水凝胶,从而将纳米硅颗粒和碳纳米管(CNT)原位包封于其中,再经冷冻干燥及随后的热处理制得三维硅/碳纳米管/石墨烯(Si-CNT@G)纳米复合材料。采用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)、热重分析(TGA)等技术对制得样品的物相、结构和微观形貌等进行了表征。结果表明,所得复合材料在CNT纵横交织的石墨烯网络中,均匀地分布着纳米硅颗粒。当作为锂离子电池的负极材料时,在两种碳介质的协同作用下,有效缓冲硅材料在充放电过程中脱/嵌锂引起的体积变化,缩短了锂离子和电子传输的距离,Si-CNT@G复合材料表现出较好的循环稳定性以及倍率性能。在500 m A·g~(-1)的充放电电流密度下,经过200圈循环后,其放电比容量仍高达673.7 m Ah·g~(-1),容量保持率高达97%;即使将充放电电流密度升至2000 m A·g~(-1)时,该复合材料仍保持有566.9 m Ah·g~(-1)的高可逆放电比容量。独特的制备方法和优越的储锂性能,使得Si-CNT@G纳米复合材料成为理想的高性能锂离子电池负极材料的候选.     

交流放电法合成多种形态的碳纳米管

碳纳米管的发现［１］引起了科学界的广泛重视,人们对于这种新型材料在纳米导线、高强纤维、超导等方面的应用寄予厚望．目前,合成碳纳米管的方法主要是采用不等径石墨棒直流放电,在阴极上得到含有碳纳米管的沉积物［２］．对于碳纳米管的应用,有关的理论研究［３］及...     

Sensitive Detection of Elemental Mercury Vapor by Gold Nanoparticle Decorated Carbon Nanotube Sensors

Low-cost, low power consumption gas sensors that can detect or quantify various gas analytes are of increasing interest for various applications ranging from mobile health, to environmental exposure assessment and homeland security. In particular miniature gas sensors based on nanomaterials that can be manufactured in the form of sensor arrays present great potential for the development of portable monitoring devices. In this study, we demonstrate that a chemiresistive nanosensor comprised of single walled carbon nanotubes decorated with gold nanoparticles has impressive sensitivity to elemental mercury (Hg) gas concentrations, with a lower detection limit as low as 2 ppb(v). Furthermore, this nanosensor was found to regenerate, though slowly, without any additional recovery steps. Finally, the mercury vapor sensing mechanism allowed for direct investigations into the origin of Surface Enhanced Raman Scattering (SERS) in carbon nanotubes decorated with Au nanoparticles.     

取向碳纳米管制备方法及其应用进展*

碳纳米管有广阔的应用前景,但很多应用是以碳纳米管定向的取向排列为前提.本文全面介绍了制备取向碳纳米管的各种方法和研究进展,综合阐述了各种制备方法的特点,并初步讨论了制备取向生长碳纳米管各种方法的机理.最后,对取向碳纳米管的应用进行了展望,提出了碳纳米管应用的新思路.     

Ion diffusion and electrochemical capacitance in aligned and packed single-walled carbon nanotubes

Direct measurement of ion diffusion in aligned, densified single-walled carbon nanotube electrodes showed that the diffusion coefficient for transport of ions (KSCN in acetonitrile) parallel to the alignment direction of the nanotubes was close to the theoretical limit of perfectly straight pores, achieving a value 20 times larger than that of activated carbon electrodes (1 × 10(-5) vs 5 × 10(-7) cm(2)/s). In contrast, the diffusion coefficient for ion transport perpendicular to the alignment direction was an order of magnitude smaller (8 × 10(-7) cm(2)/s). As an example of the ramifications of this anisotropic diffusion phenomenon, the difference in performance of the aligned carbon nanotubes as electrochemical-capacitor electrodes was evaluated. At low discharge rates, the performances of the two orientations were identical, but as the discharge rate was increased, a more rapid decline in capacitance was observed for the perpendicular orientation (66 vs 14% decline in capacitance when the discharge current was increased from 0.01 to 1 A/g). Furthermore, the maximum power rating of the perpendicular electrode was lower than that of the parallel electrode (1.85 vs 3 kW/kg during operation at 1 V).