胶束增强型聚电解质微胶囊的制备

采用杂化碳酸钙微球作为模板, 利用LbL技术, 选择聚苯乙烯磺酸钠(PSS), 烯丙基胺的盐酸盐(PAH)和二烯丙基二甲基胺盐酸盐(PADA)聚电解质, 分别组装了PAH/PSS(弱/强)聚电解质胶囊和PADA/PSS(强/强)聚电解质微胶囊. 除去模板后得到了球形良好、分散均匀的聚电解质微胶囊. 研究结果表明, 利用杂化碳酸钙微球作为聚电解质微胶囊的模板, 得到的微胶囊的囊壁厚而致密, 同时, 由于组装采用的聚电解质的种类不同, 囊壁的微观形貌有较大差异.     

原位凝聚法制备聚电解质微胶囊——模板中掺杂聚电解质量对微胶囊结构与性能的影响

通过在CaCO3制备过程中加入不同浓度聚苯乙烯磺酸钠(PSS)的方法来控制掺杂进CaCO3粒子中的PSS含量,得到了PSS掺杂量为4%～11%,尺寸均匀的CaCO3球形微粒.在微粒表面仅吸附一层聚烯丙基胺盐酸盐(PAH)后,用乙二胺四乙酸二钠(EDTA)使碳酸钙溶解;释放出的PSS与PAH原位凝聚制备得到了分散良好且完整的聚电解质复合物微胶囊.在所研究的范围内,模板微粒中PSS的含量对微胶囊的形态结构和性能没有明显影响.与传统的层层组装微胶囊相比,聚电解质复合物微胶囊有较好的热稳定性,但在高盐浓度下尺寸收缩程度较大.由于和层层组装微胶囊相比缺乏结合紧密的有序结构,原位凝聚法制备的微胶囊囊壁的截留分子量较大.     

聚电解质层层自组装纳滤膜*

层层自组装技术能够方便地对膜的微观结构和组成进行调控,已在制备复合型纳滤膜方面取得了迅速的发展。本文综述了近年来用于聚电解质层层自组装纳滤膜的制备方法,种类以及影响因素。介绍了静态层层交替沉积、压力驱动自组装和电场强化自组装等三种制备方法;归纳了均聚型、共聚型和有机/无机杂化型等三类用于层层自组装纳滤膜的聚电解质的特点;讨论了聚电解质的荷电性、电荷密度和电离程度等因素对其自组装膜分离性能的影响。总结了聚电解质自组装纳滤膜在水处理和有机溶剂中物质的分离等方面的应用。同时,对提高聚电解质自组装纳滤膜的组装效率,分离性能和发展方向提出了设想和建议。     

基于碳酸钙模板的特殊形状层层组装微胶囊的制备

以Na_2CO_3和CaCl_2为原料,聚烯丙基胺盐酸盐(PAH)为添加剂,通过磁力搅拌和超声混合的方式分别制备了两面凸碟形仿血小板形状和纺锤形的碳酸钙微粒.仿血小板形状的碳酸钙微粒为球霰石晶相,而纺锤形碳酸钙微粒为文石晶相.模板微粒中均掺杂了少量PAH.溶液混合方式和PAH添加剂的协同作用导致了特殊形状碳酸钙微粒的形成.以这2种粒子为模板通过层层组装技术分别制备了仿血小板形状和纺锤形微胶囊.得到的微胶囊能够在水中分散良好并保持模板的特殊形状.     

聚电解质层层自组装线性多层膜的电荷分区互补理论建立及膜内聚电解质离子化率

提出了聚电解质层层自组装线性多层膜的电荷分区互补理论,基于该理论建立了表面电荷密度、诱导电荷、聚电解质的吸附量和形态、膜内电荷存在形态之间的半经验数学模型。提出了计算膜内聚苯乙烯磺酸钠（PSSS）与聚烯丙基胺盐酸盐（PAH）的离子化率和电荷诱导效应的方法,讨论了处于最外层和次外层聚电解质的离子化率的不同及其与聚电解质强弱的关系。该方法比红外光谱法和光电子能谱法更简便,可用于研究所有聚电解质的离子化率。     

交联壳聚糖水凝胶填充层状微胶囊的制备与性能

在甲基丙烯酸和乳酸接枝修饰的水溶性壳聚糖(CML)存在下, 合成了尺寸均匀的球形CML杂化碳酸钙微粒. 通过层层组装(LBL)技术在该微粒表面形成了聚苯乙烯磺酸钠(PSS)/聚烯丙基胺盐酸盐(PAH)多层膜, 去除碳酸钙微粒后得到内部含有CML的聚电解质微胶囊. 进一步采用紫外光引发CML聚合, 将CML转化为CML微凝胶, 得到内部填充凝胶的微胶囊. 通过扫描电镜、光学显微镜和透射电镜等技术表征了微胶囊的结构. 与传统的LBL微胶囊不同, 凝胶填充的微胶囊干燥时尺寸收缩, 但仍可保持球形; 再次水化后, 能够膨胀恢复其原有尺寸和形态. 各种具有不同电荷性质、分子量和亲疏水性的染料分子及蛋白质均可有效地装载到微胶囊内.     

聚电解质结构及盐浓度对基于DNA和聚阳离子的层层组装型大孔薄膜结构的影响

选择2种不同类型的聚阳离子[强电解质型聚二烯丙基二甲基氯化铵(PDDA)和弱电解质型聚盐酸丙烯胺(PAH)], 分别和脱氧核糖核酸(DNA)分子通过静电吸附作用制备层层组装膜. 利用原子力显微镜和紫外-可见分光光度计研究了聚阳离子结构和组装分子溶液中盐(NaCl)浓度对大孔结构及薄膜生长规律的影响. 结果表明, 在DNA/PDDA体系中, 盐浓度对于大孔结构的形成起到关键性作用. 而对于DNA/PAH薄膜体系, 即使增加DNA或PAH溶液中盐的浓度, 也不会有大孔结构出现, 这主要是由PAH分子的弱电解质特性决定的.     

胶束增强型聚电解质胶囊的结构研究

研究了胶束增强型聚电解质(PAH/PSS和PADA/PSS)胶囊在不同溶液环境中的形貌变化,发现这种新型的胶囊具有迥异于传统聚电解质胶囊的囊壁结构;研究了二维聚电解质复合膜与模板溶解液中嵌段共聚物PS-b-PAA胶束之间的相互作用,发现胶束层可以通过静电力与聚电解质胶囊囊壁相互作用.同时,模拟模板溶出后聚电解质胶囊内部的环境条件,研究了嵌段共聚物胶束在胶囊内部的存在状态及其在透析过程中的变化规律,认为共聚物可以通过疏水作用沉积于聚电解质复合膜的内壁,并通过Ca2+离子的桥联作用稳定,也就是在聚电解质复合膜层基础上又形成了一层胶束层.即这种胶束增强型聚电解质微胶囊的囊壁是由聚电解质层和胶束层所形成的双层结构.用这种双层结构模型,我们合理解释了胶囊在高盐离子浓度下的形貌变化.     

层层组装微胶囊的制备及其智能响应与物质包埋释放性能

在胶体微粒模板上进行聚合物间或聚合物和小分子间的交替层层(LBL)组装, 得到核壳微粒, 然后去除胶体微粒得到层层组装微胶囊. 综述了层层组装微胶囊在组装驱动力、智能响应性能和物质包埋与释放等方面的最新研究进展. 首先从组装驱动力和微胶囊结构调控出发, 简述了基于静电和氢键作用的LBL微胶囊的交联方法及交联所引起的微胶囊结构和性能的变化, 介绍了基于新驱动力如共价键作用、 碱基对作用和主客体作用制备LBL微胶囊的技术. 讨论了LBL微胶囊的智能响应性, 包括pH、 温度、 电荷、 光电磁和化学物质响应等. 详细介绍了LBL微胶囊包埋与释放功能物质尤其是药物、 蛋白和酶的方法及其特色, 包括LBL直接包埋与释放、 预吸附或共沉淀包埋与释放、 电荷选择性自沉积包埋与释放及爆释等. 最后, 着眼于微胶囊的靶向传递和功能器件, 介绍了采用静电作用和生物识别作用制备得到的微胶囊阵列.     

糖响应性生物基聚电解质胶囊的制备与性能研究

选用功能单体3-氨基苯硼酸(APBA)和乳糖酸(LA)分别对聚谷氨酸(γ-PGA)和壳寡糖(CS)接枝改性后制备聚谷氨酸-g-氨基苯硼酸(γ-PGA-g-APBA)及糖基化壳寡糖(GC); 以二氧化硅微球为模板, 通过γ-PGA-g-APBA和GC间的静电相互作用进行层层自组装, 再经脱除模板则可获得形貌规整可控的生物基胶囊. 通过红外光谱(FTIR)和核磁共振(¹H NMR)对聚合物化学结构、接枝率进行表征; 利用Zeta电位监测聚合物电解质层层自组装的进程, 并通过透射电镜(TEM)和扫描电镜(SEM)观测胶囊的形貌. 同时考察了胶囊在不同温度、盐浓度、pH值及糖浓度下的刺激响应, 研究结果表明胶囊在一定的温度、盐浓度、pH值下能稳定存在; 低浓度葡萄糖刺激时胶囊形貌完整, 而高浓度葡萄糖刺激时, 胶囊溶胀直至结构与形貌破坏, 说明功能单体LA和APBA的引入可赋予胶囊具有葡萄糖响应性. 这种具有良好稳定性和葡萄糖响应性的生物基胶囊有望应用于糖尿病的诊断和治疗.     

Directed Self-assembly of Vertical PS-b-PMMA Nanodomains Grown on Multilayered Polyelectrolyte Films

Layer-by-layer polyelectrolyte self-assembly, a common method for preparing high-quality ultra-thin films, was employed to direct the self-assembly behavior of polystyrene-block-poly(methyl methacrylate)(PS-b-PMMA) block copolymer for the first time. Differing from the previous neutral polymer brushes anchored to silicon substrates via chemical modification, polyelectrolyte multilayers(PEMs) were anchored by electrostatic interaction and provided a stable, smooth, and neutral interface. In the present study, PS-b-PMMA was deposited on poly(acrylamide hydrochloride)/poly(acrylic acid)(PAH/PAA) PEMs prepared by layer-by-layer self-assembly to successfully yield vertical nanodomains after thermal annealing. Seven layered PEMs revealed an excellent, smooth surface, with a low roughness of 0.6 nm. The periodic structure with interlamellar spacing of 47 nm was determined by grazing-incidence small-angle X-ray scattering(GISAXS). The morphology of the PS-b-PMMA nanodomains depended on the polyanion-to-polycation concentration ratio, which is related to the interaction between the block copolymer and the substrate. Our results demonstrate that layer-by-layer self-assembly is a helpful method for the phase separation of block polymers and the fabrication of vertical, ordered nanodomains.     

Interactions between multivalent ions and exponentially growing multilayers: dissolution and exchange processes

The interactions between multivalent ions (small ions or polyelectrolytes) and two exponentially growing polyelectrolyte multilayers, namely, (HA-PLL)(n)() and (HA-PAH)(n)() films, are investigated (HA = hyaluronic acid, PLL = poly-l-lysine, PAH = poly(allylamine)). Ferrocyanide and ferricyanide ions are used as small ion probes. The most striking finding is that, even though these two ions differ only by one charge unit, the ferrocyanide ions induce a partial dissolution of both multilayers whereas these films remain stable in the presence of ferricyanide ions. The dissolution process of (HA-PLL)(n)() films is more rapid than that of (HA-PAH)(n)() films, indicating a stronger interaction between HA and PAH compared to HA and PLL. This is confirmed by polyelectrolyte exchange experiments: when an (HA-PLL)(n)() multilayer film is put into contact with a PAH solution, PLL is quantitatively exchanged with the PAH chains and transformed into an HA-PAH film, whereas an (HA-PAH)(n)() multilayer remains stable in the presence of a PLL solution.     

Layer-by-layer electrostatic self-assembly of single-wall carbon nanotube polyelectrolytes

We have used anionic and cationic single-wall carbon nanotube polyelectrolytes (SWNT-PEs), prepared by the noncovalent adsorption of ionic naphthalene or pyrene derivatives on nanotube sidewalls, for the layer-by-layer self-assembly to prepare multilayers from carbon nanotubes with polycations, such as poly(diallyldimethylammonium) or poly(allylamine hydrochloride) (PDADMA or PAH, respectively), and polyanions (poly(styrenesulfonate), PSS). This is a general and powerful technique for the fabrication of thin carbon nanotube films of arbitrary composition and architecture and allows also an easy preparation of all-SWNT (SWNT/SWNT) multilayers. The multilayers were characterized with vis-near-IR spectroscopy, X-ray photoelectron spectroscopy (XPS), surface plasmon resonance (SPR) measurements, atomic force microscopy (AFM), and imaging ellipsometry. The charge compensation in multilayers is mainly intrinsic, which shows the electrostatic nature of the self-assembly process. The multilayer growth is linear after the initial layers, and in SWNT/polyelectrolyte films it can be greatly accelerated by increasing the ionic strength in the SWNT solution. However, SWNT/SWNT multilayers are much more inert to the effect of added electrolyte. In SWNT/SWNT multilayers, the adsorption results in the deposition of 1-3 theoretical nanotube monolayers per adsorbed layer, whereas the nominal SWNT layer thickness is 2-3 times higher in SWNT/polyelectrolyte films prepared with added electrolyte. AFM images show that the multilayers contain a random network of nanotube bundles lying on the surface. Flexible polyelectrolytes (e.g., PDADMA, PSS) probably surround the nanotubes and bind them together. On macroscopic scale, the surface roughness of the multilayers depends on the components and increases with the film thickness.     

In situ Molecular Self-assembly and Sensitive Label-free Detection of Streptavidin via a Wavelength Interrogated Surface Plasmon Resonance Sensor

The sensing sensitivity of wavelength interrogated surface plasmon resonance（WISPR） biosensor is improved by self-assembly of polyelectrolyte multilayer（PEM） film of poly（allylamine hydrochloride）（PAH）/ poly（sodium-p-styrenesulfonate）（PSS） on the Au film coated glass chip via the layer-by-layer（LBL） technique. The home-made WISPR with Krestchmann configuration consists of a tungsten-halogen lamp as a photon source and a charge coupled device（CCD） camera as the detector. The influence of PEM film thickness on the optical properties of WISPR biosensors was investigated theoretically and experimentally. In order to achieve higher sensing sensitivity, the PEM film thickness has to be designed as ca.14 nm at an Au layer thickness of 50 nm and an incidental angle of 11.8°. Furthermore, the PEM coated WISPR biosensor can serve as highly sensitive biosensor, in which the biotin-streptavidin is used as bioconjugate pair. After deposition of the PEM film of （biotin/PAH）（PSS/PAH）3, the modified WISPR biosensor is more sensitive to the low concentration（〈0.01 mg/mL） of streptavidin. And the sensing sensitivity can be further increased by one order of magnitude compared with that of the biotin/PAH coated WISPR biosensor. Thus, such low-cost, high-performance and efficient PEM-coated WISPR biosensors have great potentials in a diverse array of fields such as medical diagnostics, drug screening, food safety analysis, environmental monitoring, and homeland security.     

Layer-by-layer nanoassembly of polyelectrolytes using formamide as the working medium

Formamide, in its pure state, has been used as a working solvent for layer-by-layer (LbL) polyelectrolyte self-assembly. Polystyrene sulfonate (PSS) and polyallylamine hydrochloride (PAH) polyelectrolyte films were deposited onto planar substrates and colloidal particles. Film deposition was confirmed using quartz crystal microbalance and zeta potential measurements. Formamide was used as an alternative to the water-based working solvents commonly used for LbL self-assembly. Few LbL self-assembly studies using nonaqueous solvents have been reported. Most studies performed with nonaqueous solvents have required the addition of small volumes of water to dissolve the polyelectrolytes. Conversely, the high dielectric constant of pure formamide led to the dissolution and transport of PSS and PAH. Using formamide, it is possible to deposit nanometer thick polyelectrolyte films onto water-sensitive surfaces. Formamide can be thus be used for encapsulating water sensitive hydrogen storage materials within polyelectrolyte films.     

Assembly and Characterization of Rare-earth-containing Polyoxometalate [Eu （P2Mo17O61）2]^17- and Poly（allylamine hydrochloride） Multilayer Films

The ultrathin multilayer films of rare-earth-containing polyoxometalate cluster K17[Eu(P2Mo17O61)2](EuPMo) and poly(allylamine hydrochloride) (PAH) have been prepared by the Layer-by-Layer(LbL) selfassembly method. The photoluminescent behavior of the films investigated at room temperature shows the Eu^3 characteristic emission pattern of ^5Do→^7FJ(J=1—4). The occurrence of the photoluminescent activity confirms the potential of creating luminescent multilayer films with polyoxometalates (POMs).     

Layer-by-layer self-assembly of multiwalled carbon nanotube polyelectrolytes prepared by in situ radical polymerization

Anionic and cationic multiwalled carbon nanotube polyelectrolytes, prepared by covalent modification of multiwalled carbon nanotubes (MWCNTs) with poly(acrylic acid) and poly(acrylamide), were used for the layer-by-layer (LBL) self-assembly of MWCNTs on different substrates with polyelectrolytes, such as poly(diallyldimethylammonium chloride) and sodium poly(styrenesulfonate). Thermogravimetric analysis, Raman spectroscopy, and scanning electron microscopy (SEM) were used to demonstrate the modification of MWCNTs. Investigations using Fourier transform infrared spectroscopy, atomic force microscopy, SEM, and ultraviolet-visible spectroscopy proved this method to be practicable for preparing LBL films.     

High-flux nanofiltration membranes prepared by adsorption of multilayer polyelectrolyte membranes on polymeric supports

Layer-by-layer deposition of anionic and cationic polyelectrolytes readily converts polymeric ultrafiltration membranes into materials capable of nanofiltration. ATR-FTIR spectra confirm that layer-by-layer deposition occurs on the ultrafiltration substrates, and adsorption of as few as 2.5 bilayers of poly(styrenesulfonate) (PSS)/protonated poly(allylamine) (PAH) or 3.5 bilayers of PSS/poly(diallyldimethylammonium chloride) (PDADMAC) reduces the molecular weight cutoff of polyethersulfone ultrafiltration supports from 50 kDa to <500 Da. Deposition of multilayer polyelectrolyte films on 300 and 500 kDa membranes also decreases molecular weight cutoffs, but solute rejections are significantly lower when using these supports, suggesting that the polyelectrolyte films do not completely cover large (0.2-0.4 microm in diameter) pores. On the 50 kDa substrates, PSS/PDADMAC films containing 3.5 bilayers exhibit a 95% rejection of SO(4)(2-) and a chloride/sulfate selectivity of 27, whereas 4.5-bilayer PSS/PAH coatings show a glucose/raffinose selectivity of 100. Pure water flux for [PSS/PAH](3)PSS-coated membranes at 4.8 bar is 1.6 m(3)/(m(2)day), which is more than 2-fold higher than that through a commercial 500 Da membrane.     

Preparation and characterization of the nanoporous ultrathin multilayer films based on molybdenum polyoxometalate (Mo38)n

Ultrathin multilayer films of the wheel-shaped molybdenum polyoxometalate cluster (Mo₃₈)_n and poly(allylamine hydrochloride)(PAH) have been prepared by the layer-by-layer (LbL) self-assembly method. The ((Mo₃₈)_n/PAH)_m multilayer films have been characterized by X-ray photoelectron spectra (XPS) and atomic force microscopy (AFM). UV-VIS measurements reveal regular film growth with each (Mo₃₈)_n adsorption. The electrochemistry behavior of the film at room temperature was investigated.     

Electrodeposition of layered manganese oxide nanocomposites intercalated with strong and weak polyelectrolytes

Multilayered manganese oxide nanocomposites intercalated with strong (poly(diallyldimethylammonium) chloride, PDDA) and weak (poly(allylamine hydrochloride), PAH) polyelectrolytes can be produced on polycrystalline platinum electrode in a thin film form by a simple, one-step electrochemical route. The process involves a potentiostatic oxidation of aqueous Mn2+ ions at around +1.0 V (vs Ag/AgCl) in the presence of polyelectrolytes. Fully charged PDDA polycations are accommodated tightly in the interlayer space by electrostatic interaction with negative charges on the manganese oxide layers, leading to an interlayer distance of 0.97 nm. The layered film prepared with PAH has a larger polymer content (PAH/Mn molar ratio of 0.98) than that (PDDA/Mn molar ratio of 0.43) made with PDDA because of the smaller charging degree of PAH, exhibiting a larger interlayer distance (1.19 nm). The interlayer PAH contains neutral (-NH2) and positively charged (-NH3(+)) amine groups, and the -NH3(+) groups are associated with Cl- (to generate -NH3(+) Cl- ion pairs) as well as the negatively charged manganese oxide layers. Both polyelectrolytes once incorporated were not ion exchanged with small cations in solution. The layered structure of PDDA/MnO(x) was collapsed during the reduction process in a KCl electrolyte solution, accompanying an expansion of the interlayer as a result of incorporation of K+ ions for charge neutrality. On the contrary, the layered PAH/MnO(x) film showed a good electrochemical response due to the redox reaction of Mn3+/Mn4+ couple with no change in the structure. X-ray photoelectron spectroscopy revealed that, in this case, excess negative charges generated on the manganese oxide layers upon reduction can be balanced by the protons being released from the -NH3(+) Cl- sites in the interlayer PAH; the Cl- anions becoming unnecessary are inevitably excluded from the interlayer, and vice versa upon oxidation.