Improvement of surface cementitious properties of coarse fly ash by dehydration and rehydration processes

Owing to poor bonding between coarse fly ash particles and hydration products, gap-graded blended cements with fly ash usually show lower compressive strengths than Portland cement. Surface cementitious properties of coarse fly ash were improved by dehydration and rehydration processes in the present study. The results show that during the calcination at 750?°C, C?CS?CH gel is mainly transformed into a new nesosilicate, which is similar to a less crystalline C₂S. The formation of melilite from hydration products is also noticed at 900?°C, however, this will not contribute to rehydration of calcined fly ash. Rehydration of new generated nesosilicate on the surface of coarse fly ash leads to a better bonding between coarse fly ash particles and hydration products. As a result, both early and late mechanical properties of gap-graded blended cements containing 25% cement clinker and 39% calcined coarse fly ash are higher than those of 100% Portland cements.     

Influence of two different fly ashes on the hydration of portland cements

Fly ashes from the combustion of coal thermal power stations are commonly incorporated into portland cements and/or concretes and mortars. The chemical and morphological composition of fly ashes, together with their particle size, make them suitable as pozzolanic(non-calcic) or pozzolanic/hydraulic(highly calcic) additions to manufacture such building materials. This work focuses on the incorporation of two different fly ashes (non-calcic but of very different Fe₂O₃(%) contents, fineness and morphology) to two ordinary portland cements (of very different mineralogical composition as well), to determine the effects those have and the interactions they produce in the hydration reactions of portland cement. The main techniques employed for this study have been: conduction calorimetry and Frattini test; secondary techniques applied have also been: determination of setting times and analysis by X-ray diffraction and SEM. Analysis of the results obtained permitted to find different effects of fly ash addition on the hydration reactions of portland cements. Thus, dilution and stimulation effects augment with the increased fly ash percentage. Delay and acceleration of the reactions depend mainly on the type of portland cement and are accentuated with increased fly ash contents. Their behaviour as concerns heat dissipation mainly, depends on the type of fly ash used and is more pronounced with increased cement replacement. On the other hand, the pozzolanic activity of these fly ashes has been revealed at 7 and 28 days, but not at 2 days. Finally, pozzolanic cements can be manufactured using different portland cements and/or types of fly ashes, in the appropriate proportions and compatible qualities, depending on the effect(s) one wish to enhance at a specific age, which is according to previous general conclusions drew out of sulphate attack and chloride attack researches. This revised version was published online in July 2006 with corrections to the Cover Date.     

Influences of fly ash and fluorgypsum on the hydration heat and compressive strength of cement

The hydration heat of pure cement, fly ash single-doped cement, as well as fly ash and fluorgypsum co-doped cement were investigated by means of micro-calorimetry with an eight-channel micro-calorimeter. The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the co-doped cement was appeared earlier than that of the single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of both the doped cement were reduced, and the exothermic peak appeared later. The effect of fly ash and fluorgypsum on the compressive strength of cement was also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the single-doped cement. Based on the experiment results obtained in this article, we could conclude that fluorgypsum is a suitable additive for the single-doped cement.     

Studies of cementitious systems with new generation by-products from fluidised bed combustion

The rate of heat evolution as well as total heat output are strongly affected by other components of hydrating mixture, apart from neat portland cement, such as slag, fly ash and other industrial by-products; among them the wastes from fluidised bed combustion (FBC) has been taken into account recently. In this study the calorimeter was applied to follow the early hydration of cements produced with these materials. They interact with cement paste in a few ways: as set controlling agent and as active pozzolanic admixtures. Thus the rate of heat evolution/hydration is modified, depending on the composition of clinker and percentage of waste in the mixture. After the series of measurements for clinker-waste mixture hydrated systems also some ‘model’ mixtures were investigated to separate the effects from particular waste components. This revised version was published online in July 2006 with corrections to the Cover Date.     

Investigations of cement early hydration in the presence of chemically activated fly ash

The paper describes an attempt of chemical activation of fly ash and claims the usefulness of combination of such investigation methods as calorimetry and infrared absorption for investigations of early periods of cement hydration. The research samples were cement pastes made with an addition of fly ash and admixtures of chemical activators, CaCl₂, Na₂SO₄ and NaOH, whereas a cement paste without fly ash addition and a cement-fly ash paste (both without admixtures) were used as reference samples. In order to investigate early periods of cement pastes hydration, the amount and rate of heat release were registered, and IR spectrums were checked at appointed hydration moments. As a result, it was shown that the combination of calorimetric and IR absorption methods in the investigations of early periods of cement hydration was useful. It was confirmed that the use of chemical activators CaCl₂, Na₂SO₄ and NaOH accelerated the hydration of cement pastes containing fly ash additive in early hours after adding water. The action of activators on hydrating cement system is different for each of investigated compounds.     

Identification of Composite Cement Hydration Products by Means of X-Ray Diffraction

 In this paper the effect of limestone, fly ash, slag and natural pozzolana on the cement hydration products is studied. Four composite cements containing limestone, natural pozzolana from the Milos Island, slag and fly ash have been produced by intergrinding clinker (85%), the above main constituent (15%) and gypsum. The grinding process was designed in order to produce cements of the same 28d compressive strength. The hydrated products, formed after 1–28 days, were studied by means of X-ray diffraction. Unhydrated calcium silicate compounds of clinker and hydration products such as C*H, C*S*H and ettringite are clearly observed. Although there is not significant differentiation among samples hydrated for the same period of time, modifications of calcium aluminate hydrates as well as sulfoaluminate hydrates, are indicated by the XRD patterns. In samples of limestone cement, monocarboaluminate is formed in the first 24 hours and is still present after 28 days.     

Effects of reagents’ nature on mechanochemical synthesis of calcium titanate

The effect of alkaline hydrothermal activation of class-C fly ash belite cement was studied using thermal analysis (TG/DTG) by determining the increase in the combined water during a period of hydration of 180 days. The results were compared with those obtained for a belite cement hydrothermally activated in water. The two belite cements were fabricated via the hydrothermal-calcination route of class-C fly ash in 1 M NaOH solution (FABC-2-N) or demineralised water (FABC-2-W). From the results, the effect of the alkaline hydrothermal activation of belite cement (FABC-2-N) was clearly differentiated, mainly at early ages of hydration, for which the increase in the combined water was markedly higher than that of the belite cement that was hydrothermally activated in water. Important direct quantitative correlations were obtained among physicochemical parameters, such as the combined water, the BET surface area, the volume of nano-pores, and macro structural engineering properties such as the compressive mechanical strength.     

Reactivity of fly ash in cement paste studied by means of thermogravimetry and isothermal calorimetry

Four paste mixtures with varying replacement level of the cement content by fly ash have been studied. Due to fly ash, the acceleration period decreased and a third hydration peak was noticed with isothermal calorimetry. The total heat after 7 days increased with increasing fly ash content. From 1 to 7 days, thermogravimetry showed a higher chemically bound water and Ca(OH)₂-content for the pastes with fly ash. Between 7 and 14 days the calcium hydroxide started to be depleted due to the pozzolanic reaction. A unique relation was found between calcium hydroxide and total heat development.     

Fast physics-chemical characterization of fly ash

This paper analyzes the effect of fly ash chemical character on early Portland cement hydration and the possible adverse effects generated by the addition of gypsum. Behaviour was analyzed for pure Portland cements with varying mineralogical compositions and two types of fly ash, likewise differing in chemical composition, which were previously characterized under sulphate attack as: silicic-ferric-aluminic or aluminic-silicic ash in chemical character, irrespective if they are in nature, siliceous or siliceous and aluminous materials according to the ASTM C 618-94a. The experimental results showed that water demand for paste with a normal consistency increased with the replacement ratio in fly ash with a more aluminic than silicic chemical character, whereas it declined when silicic-ferric-aluminic ash was used. On the other hand, the differences between the total heat of hydration released at the first valley and the second peak also clearly differentiated the two types of ash. While the relative differences increased in the more aluminic than silicic ash, they declined in the more silicic than aluminic. In another vein, the findings indicate that within a comparable Blaine fineness range, the reactive alumina (Al₂O₃^r−) content in pozzolanic additions has a greater effect on mortar strength than the reactive silica (SiO₂^r−) content, at least in early ages up to 28 days. Finally, the adverse effect generated in the presence of excess gypsum is due primarily to the chemical interaction between the gypsum and the C₃A in the Portland cement and the reactive alumina (Al₂O₃^r−) in the fly ash.     

Effect of polycarboxylate type of super plasticizer on the hydration properties of composite cements

The work aims to study the effect of polycarboxylate type of super plasticizer on the hydration of composite cements. In this paper we have studied the hydration of 20 wt% fly ash (FA) blended Portland cement in the presence of 0.1 wt% super plasticizer (SP). Water consistency, setting times, non-evaporable water contents, compressive strength, water percolation, and air content measurements were carried out. In addition, X-ray diffraction studies were carried out to understand the hydration process. The results indicated the increase in compressive strength of the FA blended Portland cement in the presence of SP and with the increase of the hydration time.     

Hydration heat evolution of high-belite cement–phosphate slag binder

The influence of phosphate slag with different finenesses and activators on the hydration of high-belite cement has been studied by using the hydration heat of binders, the DTA curves, the SEM images, and the specific strength. Results indicated that doped phosphorus slag in the cement will reduce heat of hydration. The activity of phosphate slag was low at early stage, but pozzolanic activity of phosphorus slag is higher than that of fly ash. Increasing the specific surface area and curing time and using Ca(OH)₂ combined with gypsum can clearly promote the hydration degree of phosphorus slag. The findings in this paper show that since phosphorus slag can promote the hydration of high-belite cement, the strength contribution of cement is increased. Moreover, the greater the specific surface area is, the more significant the promotion effect at 90 d is.

     

Investigations of the influence of different fly ashes on cement hydration

Investigations of physico-chemical properties of three kinds of fly ash and their influence on cement hydration were performed in this work. Thermal analysis, microcalorimetry, infrared absorption and others were used. It was confirmed that the kind of coal and combustion conditions essentially influence physico-chemical properties of fly ash and in consequence influence cement hydration. Investigated fly ashes show in cement system so-called pozzolanic activity. Fly ash from combustion of brown coal in fluidized furnace revealed better activity compared to other investigated ones. This work is an introduction to more extensive investigation of fly ash activation.     

A comparison of hydration properties of cement–low quality fly ash binder and cement–limestone powder binder

The hydration properties of the binder containing low quality fly ash or limestone powder were compared in this study. Isothermal calorimetry was performed to measure the hydration heat of the binders during the first 3 days. Mercury intrusion porosimetry, scanning electron microscope, and thermogravimetry–differential thermal analysis were all used to determine the pore structure and hydration products of paste. The compressive strength of the pastes of age 3, 7, 28, and 90 days was also tested. The results indicate that the ground low quality fly ash can improve the mechanical properties of composite cementitious material and ameliorate the hydration properties and microstructure compared with the inert admixture limestone powder. The chemical activity of low quality fly ash presents gradually and appears high pozzolanic effect at later period, and it can accelerate the generation of hydration products containing more chemically bonded water. This leads to the higher rate of strength growth and cement hydration degree, the more compact microstructure and reasonable pore size distribution. Additionally, low quality fly ash delays the induction period, but shortens the acceleration period, therefore there is no significant influence on the second exothermic peak occurrence time.     

Isothermal and solution calorimetry to assess the effect of superplasticizers and mineral admixtures on cement hydration

The heat of hydration evolution of eight paste mixtures of various water to binder ratio and containing various pozzolanic (silica fume, fly ash) and latent hydraulic (granulated blast furnace slag) admixtures have been studied by means of isothermal calorimetry during the first 7 days of the hydration process and by means of solution calorimetry for up to 120 days. The results of early heat of hydration values obtained by both methods are comparable in case of the samples without mineral admixtures; the values obtained for samples containing fly ash and granulated blast furnace slag differ though. The results from isothermal calorimetry show an acceleration of the hydration process by the presence of the fine particles of silica fume and retarding action of other mineral admixtures and superplasticizer. The influence of the presence of mineral admixtures on higher heat development (expressed as joules per gram of cement in mixture) becomes apparent after 20 h in case of fly ash without superplasticizer and after 48 h for sample containing fly ash and superplasticizer. In case of samples containing slag and superplasticizer the delay observed was 40 h. The results obtained by solution calorimetry provide a good complement to the ones of isothermal calorimetry, as the solution calorimetry enables to study the contribution of the mineral admixtures to the hydration heat development at later ages of the hydration process, which is otherwise hard to obtain by different methods.     

Heat of hydration prediction for blended cements

Prediction and control of concrete temperature rise due to cement hydration is of great significance for mass concrete structures since large temperature gradients between the surface and the core of the structure can lead to cracking thus reducing durability of the structure. Cement replacement with supplementary cementitious materials (SCMs) is frequently used to reduce the concrete temperature rise. Several models have been proposed for predicting heat release of blended cements; however, none of them address incorporation of metakaolin into the mixture. Isothermal calorimetry measurements, based on statistical experimental design, were taken on pastes incorporating combinations of SCMs and chemical admixtures. The data were then used to develop equations to predict the total heat reduction with the incorporation of chemical admixtures and SCMs. Analysis of the calorimetry data indicated that chemical admixtures do not have a significant effect on heat evolution beyond 12 h. SCMs investigated in this study (fly ash, slag, silica fume and metakaolin), on the other hand, were found to have a significant effect at hydration ages of 12, 24, 48 and 72 h.     

The difference among the effects of high-temperature curing on the early hydration properties of different cementitious systems

The difference among the effects of high-temperature curing on the early hydration properties of the pure cement, the binder containing fly ash, the binder containing GGBS, and the binder containing steel slag was investigated by determining the compressive strength, non-evaporable water content, hydration heat, and Ca(OH)₂ content. Results show that the order of the influence degrees of high-temperature on the early hydration of different binders is the binder containing GGBS > the binder containing steel slag > the binder containing fly ash > the pure cement. In the case of short period of high-temperature curing (only 1 day), the strength growth rate of the concrete containing GGBS is the greatest. Though the influence of increasing high-temperature curing period on the hydration degree of the binder containing fly ash is not the most significant, the strength growth rate of the concrete containing fly ash is the most significant due to the excessive consumption of Ca(OH)₂ by reaction of fly ash. In the case of high-temperature curing, the Ca(OH)₂ content of the paste containing steel slag is much higher than those of the paste containing GGBS and the paste containing fly ash, so though high-temperature curing promotes the hydration of the binder containing steel slag significantly, its influence on the strength growth rate of the concrete containing steel slag is not so significant.     

Production and separation of no-carrier-added 48V from 16O irradiated chlorine target

The viability of ground coal bottom ash as a potential Portland cement constituent to be used in building materials is assessed. Currently, coal fly ash is used to produce Portland cements and concretes. However, coal bottom ash is mainly landfilled. Gamma spectrometry analysis, compressive strength, physical and chemical testing were performed. The ground coal bottom ash activity concentration index (I = 1.03) was compared to that of the coal fly ash (I = 1.11) provided from the same thermo-electrical power plant. Ground coal bottom ash could be used in building materials in the same way as coal fly ash as a Portland cement constituent.

     

Hydration behaviour of a lime-pozzolan cement containing MSW incinerator fly ash

A lime-pozzolan cement was used to make pastes containing different quantities of MSW fly ash. After setting, the pastes were cured in water at room temperature from 1 h to 260 days. The hydration characteristics and the nature of the hydration products of the various pastes were studied by simultaneous TG/DSC thermal analysis and X-ray diffractometry. The MSW fly ash was found to induce a slowing of the hydration process in lime-pozzolan pastes, and after some days an evident acceleration of hydration reactions occurred. Sulphate and chloride in the MSW fly ash yield hydration products forming a cementitious matrix.The author is grateful to D. Calabrese for assistance with the thermal and XRD analyses.     

Hydration,mechanical properties and durability of high-strength concrete under different curing conditions

The properties of high-strength concrete under standard curing condition (20 °C, 95% RH), high-temperature curing condition (50 °C) and temperature match curing condition were comparatively investigated. The cumulative hydration heat of composite binder containing fly ash and silica fume is lower than that of composite binder containing the same amount of slag. Addition of fly ash and silica fume clearly reduces the adiabatic temperature rise of concrete, but adding slag leads to higher adiabatic temperature rise than Portland cement concrete. High-temperature curing condition and temperature match curing condition lead to the sustainable increase in compressive strength of concrete containing mineral admixture, but they hinder the later-age strength development of Portland cement concrete. For cement–slag paste and cement–fly ash–silica fume paste, the non-evaporable water contents increase significantly and the pore structures are much finer under high-temperature curing condition and temperature match curing condition, which negatively affect the pore structure of Portland cement paste. The differences in properties of concrete among three curing conditions become smaller with time. The properties obtained under standard curing condition can approximately reflect the long-term properties of high-strength concrete in the real structure. The concrete prepared with cement–fly ash–silica fume composite binder has the highest compressive strength, finest pore structure and best resistance to chloride permeability under any curing condition. This composite binder is very suitable to prepare the high-strength concrete with large volume.     

Comparative investigation of reactivity of different kinds of fly ash in alkaline media

Comparison of the influence of temperature and different alkali activators on the reactivity of two types of fly ash (conventional, fluidized) was presented. The main emphasis was put on fluidized fly ash as potential component of binding mixtures containing low amount of cement. Conventional fly ash was used as a reference. It was found that for these materials the key differences affecting products of activation are: availability of calcium and sulfate ions as well as structure of fly ash grains influencing dissolution of aluminate and silicate species. Fluidized fly ash, contrary to conventional fly ash, undergoes reaction in 0.1 M solutions of hydroxides forming mainly ettringite. In the case of 4 M hydroxides, both fly ashes undergo hydration processes. Conventional fly ash formed mainly amorphous aluminosilicate gel, while fluidized fly ash may create zeolitic products especially in the case of elevated temperature of early hydration. Sulfate and alkali ions can be incorporated into aluminosilicate structure of new formed products; however, this process depends strictly on the type of used hydroxide and its concentration. The presence of Ca(OH)₂, carbonates and alkali sulfates was also registered in the case of hydrated fluidized fly ash.