Pt-Al/MCM-41催化剂的制备及催化合成有机硅增效剂

以介孔硅MCM-41为载体,AlCl₃为促进剂,制备了负载型Pt-Al/MCM-41催化剂。利用傅里叶红外光谱（FTIR）、N₂吸附-脱附、X射线衍射（XRD）、透射电子显微镜（TEM）、X射线光电子能谱（XPS）、电感耦合等离子体发射光谱（ICP）对催化剂的结构、形貌以及金属间作用力进行了表征,着重探讨了不同Al加入量对催化剂结构和金属间作用力的影响,系统考察了Pt-Al/MCM-41用于催化聚乙二醇烯丙基醚和七甲基三硅氧烷合成有机硅增效剂。结果表明,Al的加入量对催化剂的结构和有序度有一定的影响,其比表面积、孔容和有序度随着Al用量的增加而逐步降低。此外,加入一定量的Al有利于提高Pt晶粒的分散度,减小其粒径。Pt₁Al₂/MCM-41催化剂具有良好的重复使用性,使用6次无明显失活,其转化率仍大于90%。合成有机硅增效剂的最佳工艺为：n_PGAE/n_MD^HM=1.1,反应时间为4 h,反应温度为100℃,催化剂用量为0.5%,其转化率达94.1%。     

三种碳材料上原位电沉积AuPt合金的催化性能

在碳纸（CP）及涂覆了碳粉科琴黑（KB）或石墨烯纳米片（GNs）的碳纸上,原位电沉积了AuPt合金,制备成CP/AuPt、CP/KB/AuPt、CP/GNs/AuPt三种空气电极。对比研究发现,以石墨烯纳米片为载体的CP/GNs/AuPt空气电极上,AuPt合金载量高,颗粒分散均匀,粒径约为100 nm左右,Au和Pt的含量分别为78.84%（n/n）和21.16%（n/n）。在0.1 mol·L^-1 KOH溶液中氧还原反应的起峰电势为0.93 V,催化活性和稳定性优于其他两种空气电极。分析认为,石墨烯纳米片具有高导电性、高比表面积以及较多的缺陷活性位点,有利于AuPt合金在其上均匀电沉积且沉积载量较高,同时GNs本身具有一定的催化活性,两者能够产生协同催化作用,提高了CP/GNs/AuPt电极的催化性能。     

Pt/MIL-101(Cr)在肉桂醛选择性加氢反应中的催化性能

采用简单易行的浸渍法将Pt纳米粒子负载到MIL-101(Cr)上,制备了Pt/MIL-101(Cr)催化剂,并对其在肉桂醛选择性加氢反应的催化性能进行了研究。XRD、N₂吸附、TEM和催化性能的研究结果表明,Pt的负载量对负载于MIL-101(Cr)上Pt纳米粒子的尺寸及所制备催化剂对肉桂醇的选择性有很大影响。低Pt负载量(1.0%)的Pt/MIL-101(Cr)较其他MOFs和无机材料在肉桂醛选择性加氢反应中表现出了高的催化性能,在优化的反应条件下肉桂醛转化率和对肉桂醇的选择性可分别达96.5%和86.2%。Pt/MIL-101(Cr)催化剂具有良好的稳定性。Pt/MIL-101(Cr)所表现出的优良的催化性能同MIL-101(Cr)载体的孔道结构及其表面性质密切相关。     

Pt/MIL-101(Cr)在肉桂醛选择性加氢反应中的催化性能

采用简单易行的浸渍法将Pt纳米粒子负载到MIL-101(Cr)上, 制备了Pt/MIL-101(Cr)催化剂, 并对其在肉桂醛选择性加氢反应的催化性能进行了研究。XRD、N₂吸附、TEM和催化性能的研究结果表明, Pt的负载量对负载于MIL-101(Cr)上Pt纳米粒子的尺寸及所制备催化剂对肉桂醇的选择性有很大影响。低Pt负载量(1.0wt%)的Pt/MIL-101(Cr)较其他MOFs和无机材料在肉桂醛选择性加氢反应中表现出了高的催化性能, 在优化的反应条件下肉桂醛转化率和对肉桂醇的选择性可分别达96.5%和86.2%。Pt/MIL-101(Cr)催化剂具有良好的稳定性。Pt/MIL-101(Cr)所表现出的优良的催化性能同MIL-101(Cr)载体的孔道结构及其表面性质密切相关。     

碳酸盐共沉淀法可控制备超高倍率锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2

采用碳酸盐共沉淀法通过调节NH₃·H₂O用量来实现可控制备超高倍率纳米结构LiNi_1/3Co_1/3Mn_1/3O₂正极材料。NH₃·H₂O用量会对颗粒的形貌、粒径、晶体结构以及材料电化学性能产生较大的影响。X射线衍射（XRD）分析和扫描电镜（SEM）结果表明,随着NH₃·H₂O用量的降低,一次颗粒形貌由纳米片状逐渐过渡到纳米球状,且n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品晶体层状结构最完善、Li⁺/Ni²⁺阳离子混排程度最低。电化学性能测试结果也证实了n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品具有最优异的循环稳定性和超高倍率性能。具体而言,在2.7~4.3 V,1C下循环300次后的放电比容量为119 mAh·g^-1,容量保持率为81%,中值电压基本无衰减（保持率为97%）。在100C（18 Ah·g^-1）的超高倍率下,放电比容量还能达到56 mAh·g^-1,具有应用于高功率型锂离子电池的前景。此NH₃·H₂O比例值对于共沉淀法制备其他高倍率、高容量的正/负极氧化物材料具有一定的工艺参考价值。     

铂纳米颗粒的可见光化学制备及其对p-硝基苯酚催化还原反应

在可见光照射下,以乙二醇（EG）作为还原剂和稳定剂,在多壁碳纳米管（MWCNTs）上一步合成了铂纳米颗粒,成功制备Pt/MWCNTs复合材料,并通过p-硝基苯酚（p-NP）的催化还原反应研究了Pt/MWCNTs的催化性能。用傅里叶变换红外光谱（FT-IR）、X射线衍射（XRD）、透射电子显微镜（TEM）和X射线光电子能谱（XPS）对所制备材料的形貌和晶体结构进行了表征。实验结果显示,可见光照射促进了EG水溶液中[PtCl₄]^2-前驱体的水解。通过金属界面的电子效应,铂前驱体被还原成了均匀分散的平均直径2.1 nm的超小颗粒Pt（Pt ultra-small particles,Pt UPs）。所制备的Pt/MWCNTs能有效地催化p-NP还原为p-氨基苯酚（p-AP）,表现出较高的催化性能,其表观速率常数为0.25 min^-1。Pt/MWCNTs多次使用后没有显著的活性损失,显示出了良好的稳定性。上述实验结果证明,除了传统的紫外光照射等手段以外,可见光照射也同样是制备铂金属催化剂非常有效的方法。而且,催化剂的形貌控制也完全可以通过简单而非复杂的实验条件加以实现。     

三个二羧酸配体配位聚合物的合成、结构表征和荧光性质

以羧酸配体2,2''-（1,4-亚苯基双（亚甲基））双（硫二基）二苯甲酸（H₂L¹）和2,2''-（2,3,5,6-四甲基-1,4-亚苯基）双（亚甲基）双（硫二基）二苯甲酸（H₂L²）分别与金属盐反应,通过溶剂热方法合成了3个配位聚合物：{[Ni（L¹）（H₂O）₄]·2H₂O}_n （1）、[Zn（L¹）（DMA）₂]_n （2）和[Co（L²）（DMF）₂]_n （3）,其中DMA=N,N-二甲基乙酰胺,DMF=N,N-二甲基甲酰胺。对配合物1~3进行了单晶X射线衍射、元素分析、红外光谱、热重分析、粉末X射线衍射和固体紫外可见光谱测试和表征。单晶X射线衍射表明：3个配合物均为一维锯齿形链状结构,并通过氢键作用形成三维骨架,且配体均表现为反式构象。此外,对配合物2固态荧光性质进行了研究。     

三个基于1,5-二(2-乙基苯并咪唑基)-戊烷柔性配体的镉配合物

通过设计柔性配体1,5-二（2-乙基苯并咪唑基）戊烷（bep）,在二羧酸辅助配体的调控下成功制备了3个配位聚合物[Cd（bep）（sba）]_n（1）,[Cd（bep）（bda）]_n（2）,and{[Cd₂（bep）（ada）₂]·H₂O}_n（3）（H₂sba=4,4’-磺酰基二苯甲酸,H₂bda=4,4’-联苯二甲酸,H₂ada=1,3-金刚烷二乙酸）。配合物均呈现二维层状结构。配合物1由交替的Cd（Ⅱ）/bep/sba^2-螺旋链构成。配合物2由Cd/bda^2-单元构成二维结构,bep作为单齿配体与Cd（Ⅱ）配位。配合物3的二维层通过Cd/ada^2-/H₂O氢键螺旋链拓展成三维超分子。此外,对配合物1~3的粉末X射线衍射、热稳定性以及荧光性质进行了研究。     

三个基于1，5-二(2-乙基苯并咪唑基)-戊烷柔性配体的镉配合物

通过设计柔性配体1,5-二（2-乙基苯并咪唑基）戊烷（bep）,在二羧酸辅助配体的调控下成功制备了3个配位聚合物[Cd（bep）（sba）]_n（1）,[Cd（bep）（bda）]_n（2）,and{[Cd₂（bep）（ada）₂]·H₂O}_n（3）（H₂sba=4,4’-磺酰基二苯甲酸,H₂bda=4,4’-联苯二甲酸,H₂ada=1,3-金刚烷二乙酸）。配合物均呈现二维层状结构。配合物1由交替的Cd（Ⅱ）/bep/sba^2-螺旋链构成。配合物2由Cd/bda^2-单元构成二维结构,bep作为单齿配体与Cd（Ⅱ）配位。配合物3的二维层通过Cd/ada^2-/H₂O氢键螺旋链拓展成三维超分子。此外,对配合物1~3的粉末X射线衍射、热稳定性以及荧光性质进行了研究。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂, 应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明, 酸处理NaY分子筛后, 骨架铝被脱除, 导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔, 有利于产物分子的扩散, 从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能, DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.