烟草中吡嗪和吡啶类香味成分含量及差异性研究

为了测定和比较不同烟叶及国内外代表性卷烟中的吡嗪、吡啶类香味成分含量的差异性,建立了烟草中吡嗪和吡啶类物质的同时蒸馏萃取-气相色谱-质谱联用(SDE-GC-M S)测定法,优化了同时蒸馏萃取液的净化方法以及仪器测定条件。化合物的线性系数范围为0.9957~0.9999,RSD范围为5.3%~8.6%,回收率范围为73.0%~101.4%,检出限范围为0.0015~0.0029μg/g,可以满足烟草中吡啶、吡嗪类物质的定量测定。研究发现,产地对烟叶中吡嗪、吡啶类化合物含量影响较大;烟叶不同部位中吡嗪、吡啶类化合物差异性显著;不同品种烟叶中吡嗪、吡啶类化合物含量差异性较大,晒黄烟主要是吡啶类化合物含量较高,白肋烟中吡嗪类化合物含量相对较高;混合型卷烟烟丝中吡嗪、吡啶类香味成分含量明显高于烤烟型卷烟。     

顶空-固相微萃取-气相色谱法检测可可麦汁中吡嗪类化合物

建立了顶空-固相微萃取(HS-SPME)-气相色谱快速测定可可麦汁中3种吡嗪类物质(2,5-二甲基吡嗪、2,3,5-三甲基吡嗪和2,3,5,6-四甲基吡嗪)的方法.选择不同的固相微萃取头对萃取温度和时间进行优化,所得最佳萃取条件为:在60℃下,采用75 μm CAR/PDMS萃取头对麦汁样品萃取40 min.本方法的检出限(S/N=3)为0.023～ 0.056 μg/L,线性范围1～500 mg/L;相对标准偏差为3.6％～6.4％;回收率为95.4％～102.7％.本方法应用于样品检测,发现可可麦汁中吡嗪的浓度与原料中可可粉的添加量正相关,显示了很好灵敏性.     

液相色谱-质谱联用分析土壤中的双(2-羟乙基)亚砜

建立了液相色谱 质谱联用技术测定土壤中双(2 羟乙基)亚砜的方法。对影响检测灵敏度的流动相组成、流速、探头温度等因素进行了优化,在优化实验条件下,方法线性范围在0.05～20mg L之间,最低检测质量浓度为0.025mg L(S N>3),对比了3种萃取剂对4种土壤中的双(2 羟乙基)亚砜的萃取率,结果表明,用水作萃取剂的萃取效果最佳,回收率在92%以上,RSD均小于4%。     

中药材成分有机溶剂与离子液体分散液相微萃取方法的比较及其机理探讨

研究了离子液体分散液相微萃取(ILDLPME)机理;比较了ILDLPME和有机溶剂分散液相微萃取(OSDLPME)在测定蒽醌类化合物中的异同;建立了分散液相微萃取-高效液相色谱法测定药材中6种游离蒽醌类化合物(芦荟大黄素、大黄酸、丹蒽醌、大黄素、大黄酚和大黄素甲醚)含量的方法。在优化的实验条件下,OSDLPME和ILDLPME对6种分析物的富集倍数分别为101～230和76～181;6种分析物的检出限分别在20～200ng/L和40～400ng/L之间;精密度(RSD)分别在3.1%～10.0%和1.3%～7.0%之间;4种中药材中分析物的回收率在81.7%～110.7%和81.9%～110.8%之间。离子液体在水中分散的同时进行有序排列,形成分子有序组合体,对分析物进行萃取。ILDLPME达平衡时间更快,精密度更高,方法更简便;OSDLPME浓缩倍数更高,检出限更低;两种方法对中药样品中游离蒽醌类化合物含量测定结果无显著性差异。     

食品包装用塑料制品中六种邻苯二甲酸酯类化合物的测定方法研究

探讨了食品包装用塑料制品中邻苯二甲酸酯类化合物的气质联用(GC/MS)分析方法.采用超声波辅助萃取,GC/MS的选择离子监测方式(SIM)对样品进行检测.取得了较好的线性相关性,方法的回收率达到82.5%～108.2%,变异系数小于15%.该方法操作简便,重复性好.     

微波辅助-微固相在线萃取/气相色谱质谱联用法对污泥中19种多氯联苯的测定

建立了微波辅助-微固相在线萃取/气相色谱-质谱联用(GC-MS)测定污泥中19种多氯联苯(PCBs)含量的分析方法。对微波辅助-微固相在线萃取条件进行优化,得出最优萃取条件为:萃取温度60℃,萃取时间25 min,解吸溶剂为乙酸乙酯,解吸剂用量150μL,解吸时间25 min。在优化条件下,方法的检出限为0.2~2.5 ng/g,相对标准偏差(RSD)小于14%,回收率为81.4%~102.1%。与传统的微波萃取、微固相萃取、超声萃取等方法相比,该方法集萃取、净化和浓缩于一体,极大地缩短了分析时间,适合于复杂环境样品体系中痕量PCBs的分析检测。     

解吸电晕束电离源质谱法快速检测食品包装材料中的双酚A

采用解吸电晕束电离源(DCBI)与质谱联用法测定食品包装材料中的双酚A。优化了萃取溶剂和离子源等参数。DCBI优化后,甲醇为萃取溶剂,检测模式为负离子模式,电离电压为!2 kV,离子传输管温度225℃,He气体流速1.0 L/min。当选用全扫描的模式时,单个样品测定时间小于30 s,对双酚A的检出限为0.1 mg/L,在1~100 mg/L浓度范围内线性良好,相关系数达到0.98,直接检测食品包装材料中的双酚A时,平均回收率为94%~125%,测定结果的相对标准偏差(RSD)小于17%。本方法分析速度快,灵敏度高,基体影响小,适用于大量样品快速检测。     

顶空单滴液相微萃取-气相色谱法测定水中苯胺类化合物

提出了气相色谱法测定水中苯胺、N,N-二甲基苯胺、邻甲苯胺、间甲苯胺等4种苯胺类化合物含量的方法。顶空单滴液相微萃取的优化条件如下:萃取剂为正己烷,萃取温度为25℃,液滴离萃取瓶内液面高度为2.0cm,萃取时间为13min,搅拌速率为400r·min-1。4种苯胺类化合物的质量浓度在0.100~1.00μg·L-1范围内与峰面积呈线性关系,检出限在0.006~0.014μg·L-1之间。方法用于水样分析,加标回收率在90.0%~115%之间,测定值的的相对标准偏差(n=6)均小于10%。     

顶空固相微萃取-气质联用测定环境水样中7种痕量土霉昧物质

建立了同时测定环境水样中7种痕量土霉味物质(2-甲基异冰片、土臭素、2-异丙基-3-甲氧基吡嗪、2-异丁基-3-甲氧基吡嗪、2,3,4-三氯苯甲醚、2,3,6-三氯苯甲醚和2,4,6-三氯苯甲醚)的顶空-固相微萃取气相色谱-质谱联用方法.对顶空-固相微萃取的参数进行了考察与优化,确认了最佳萃取条件:离子强度0.3 g/...     

毛细管柱-气相色谱法测定水样中硝基苯类化合物残留量

提出了HP-5毛细管柱分离气相色谱法测定水样中硝基苯类化合物残留量的方法。利用苯萃取富集水样中硝基苯类化合物,所得萃取液用作气相色谱测定,电子捕获检测器检测。在优化的试验条件下,10种硝基苯类化合物在28min内能够很好地分离,方法的检出限(2S/N)在1.0×10~(-3)～7.0×10~(-2)μg·L~(-1)之间,相对标准偏差(n=7)在1.5%～4.5%之间。方法用于地表水和废水样中硝基苯类化合物测定,加标回收率在80.2%～104.5%之间。     

Darstellung,Kristallstrukturen, Schwingungsspektren und Normalkoordinatenanalyse von vier bindungsisomeren Trichlorotrirhodanoosmaten(IV)

Preparation, Crystal Structures, Vibrational Spectra, and Normal Coordinate Analysis of four Linkage Isomeric Trichlorotrirhodanoosmates(IV) By treatment of fac-[OsCl₃I₃]^2? with (SCN)₂ in dichloromethane the linkage isomers fac-[OsCl₃(NCS)₃]^2? ( 1 ), mer-[OsCl₃(NCS)₂^c(SCN)]^2? ( 2 ), mer-[OsCl₃(NCS)(SCN)₂^t]^2? ( 3 ), and mer-[OsCl₃(NCS)(SCN)₂^c]^2? ( 4 ) are formed which have been separated by ion exchange chromatography on diethylaminoethyl cellulose. X-Ray structure determinations have been performed on single crystals of fac-(Ph₄As)₂[OsCl₃(NCS)₃] (triclinic, space group P1 , a = 12.142(5), b = 13.233(5), c = 19.300(5) Å, α = 98.642(5)º, β = 100.509(5)º, γ = 112.514(5)º, Z = 2), mer-(Ph₄As)₂[OsCl₃(NCS)₂^c (SCN)] · acetone (triclinic, space group P1 , a = 11.707(5), b = 13.238(5), c = 19.048(5) Å, α = 75.960(5)º, β = 88.981(5)º, γ = 69.999(5)º, Z = 2), mer-(Ph₄As)₂[OsCl₃(NCS)(SCN)₂ ^t] (triclinic, space group P1, a = 10.6861(12), b = 11.6587(5), c = 12.5232(5) Å, α = 112.069(8)º, β = 95.052(8)º, γ = 92.559(7)º, Z = 1) and mer-(Ph₄As)₂[OsCl₃(NCS)(SCN)₂ ^c] · 2acetone (triclinic, space group P1 , a = 11.444(5), b = 14.661(5), c = 15.830(5) Å, α = 75.790(5)º, β = 80.273(5)º, γ = 75.205(5)º, Z = 2). The complex anions are completely ordered. The via N or S coordinated thiocyanate groups are located nearly direct above one of the cis-positioned Cl ligands with Os? N? C angles of 169.1º, 171.5º, 175.7º ( 1 ), 175.6º, 178.6º ( 2 ), 172º ( 3 ), and 173.1º ( 4 ) and Os? S? C angles of 106.2º ( 2 ), 106.1º, 106.6º ( 3 ), 105.1º, and 108.2º ( 4 ). Using the molecular parameters of the X-Ray determinations the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salts of all four linkage isomers have been assigned by normal coordinate analyses based on a modified valence force field. The valence force constants are f_d(OsN) = 1.71 ( 1 ), 1.46 and 1.62 ( 2 ), 1.69 ( 3 ), and 1.61 ( 4 ), f_d(OsS) = 1.27 ( 2 ), 1.36 ( 3 ), 1.32, and 1.49 mdyn/Å ( 4 ). Taking into account increments of the trans influence a good agreement between observed and calculated frequencies is achieved.     

Darstellung,Kristallstrukturen, Schwingungsspektren und Normalkoordinatenanalyse von vier bindungsisomeren Tetrachlorodirhodanoosmaten(IV)

Preparation, Crystal Structures, Vibrational Spectra, and Normal Coordinate Analysis of Four Linkage Isomeric Tetrachlorodirhodanoosmates(IV) By treatment of cis- or trans-[OsCl₄I₂]^2? with (SCN)₂ in dichloromethane the linkage isomers cis-[OsCl₄(NCS)₂]^2? ( 1 ), trans-[OsCl₄(NCS)(SCN)]^2? ( 2 ), cis-[OsCl₄(NCS)(SCN)]^2? ( 3 ) and trans-[OsCl₄(SCN)₂]^2? ( 4 ) are formed which have been separated by ion exchange chromatography on diethylaminoethyl cellulose. The X-Ray structure determinations on single crystals of cis-(Ph₄As)₂[OsCl₄(NCS)₂] (triclinic, space group P1 , a = 10.019(5), b = 11.702(5), c = 21.922(5) Å, α = 83.602(5)°, β = 85.718(5)°, γ = 73.300(5)°, Z = 2), trans-(Ph₄As)₂[OsCl₄ · (NCS)(SCN)] (monoclinic, space group P2₁/c, a = 18.025(5), b = 11.445(5), c = 23.437(5) Å, β = 94.208(5)°, Z = 4), cis-(Ph₄As)₂[OsCl₄(NCS)(SCN)] (triclinic, space group P1 , a = 10.579(5), b = 11.682(5), c = 22.557(5) Å, α = 81.073(5)°, β = 85.807(5)°, γ = 87.677(5)°, Z = 2) and trans-(Ph₄As)₂ · [OsCl₄(SCN)₂] (triclinic, space group P1 , a = 10.615(5), b = 11.691(5), c = 11.907(5) Å, α = 111.314(5)°, β = 96.718(5)°, γ = 91.446(5)°, Z = 1) reveal the complete ordering of the complex anions. The via N or S coordinated thiocyanate groups are located nearly direct above one of the cis-positioned Cl ligands with Os? N? C angles of 171.2° and 174.3° ( 1 ), 162.3° ( 2 ), 172° ( 3 ) and Os? S? C angles of 108.3° ( 2 ), 105.7° ( 3 ) and 105.5° ( 4 ). Using the molecular parameters of the X-Ray determinations the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salts of all four linkage isomers are assigned by normal coordinate analyses based on a modified valence force field. The valence force constants are f_d(OsN) = 1.59 ( 1 ), 1.67 ( 2 ), 1.60 ( 3 ) and f_d(OsS) = 1.27 ( 2 ), 1.31 ( 3 ) and 1.32 mdyn Å^?1 ( 4 ). Taking into account increments of the trans influence a good agreement between observed and calculated frequencies is achieved.     

Comparative Thermogravimetric Studies of Poly(ether-ketone/sulfone) Imides and Their Parent Polymers: I. Poly(ether-ketone/sulfone) ethylimide

Thermogravimetry (TG) was employed to study the thermal degradation kinetics of poly(etherketone/sulfone)ethylimide (PEK-IE and PES-IE). The corresponding decomposition activation energies and reaction orders were obtained and the comparison was made with their parent polymerspoly(ether-ketone/sulfone) with Cardo group (PEK-C and PES-C). The results show that the degradation activation energies of PEK-IE and PES-IE were lower than that of PEK-C and PES-C; and two stages of the degradation process were found for all the four polymers. For PEK-IE and PES-IE, the activation energies in the first decomposition stage are much lower than that in the second stage and the two stages can be taken as slow induction and fast degradation, whereas for PEK-C and PES-C the activation energies in the first decomposition stage are larger than that in the second stage, and the two stages can both be taken as two fast degradation stages. The decomposition mechanism of the two stages was also speculated.This revised version was published online in November 2005 with corrections to the Cover Date.     

Darstellung und Kristallstruktur von (n-Bu4N)3[Ir(NCS)(SCN)5]

Preparation and Crystal Structure of (n-Bu₄N)₃[Ir(NCS)(SCN)₅] The evaporated ethanolic extrakt of the reaction product of K₃[IrCl₆] and HNO₃, refluxed with an aqueous KSCN solution yields a mixture of the linkage isomers [Ir(NCS)_n(SCN)_6?-n]^3?, n = 0? 2, and small amounts of linkage isomeric chloropentarhodanoiridates(III), from which [Ir(NCS)(SCN)₅]^3? has been isolated by ion exchange chromatography on DEAE-cellulose. The X-Ray structure determination on a single crystal of (n-Bu₄N)₃[Ir(NCS)(SCN)₅] (monoclinic, space group P 2₁/a, a = 17.513(5), b = 32.607(5), c = 23.661(5) Å, β = 94.757(5)°, Z = 8) confirms the existance of a heteroleptic hexakis(thiocyanato(N)-thiocyanato(S))iridate(III) with an Ir? N distance of 2.03 Å and Ir? S bond lengths between 2.29 and 2.38 Å. The SCN groups with angles between 166 and 175° are nearly linear with Ir? S? C angles from 99.9 to 109.4°. The Ir? N? C angles of the two crystallographic independent anions are 166 and 174°.     

SYNTHESIS AND CHARACTERIZATION OF METAL COMPLEXES WITH AMPICILLIN

Abstract

The reaction, in water, of Co(II), Ni(II), Cu(II), Zn(II) and Cd(II) ions with sodium ampicillinate at room temperature has allowed isolation of dimers with the following general formula [M(amp)Cl]₂ × nH₂O (n = 1.5?3.2). The complexes were characterized by elemental analyses, conductivity measurements, magnetic susceptibilities and spectroscopic methods (IR, Raman, EPR and UV-Visible). A dinuclear structure based on octahedrally coordinated metal ions is proposed.     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

Thermal Degradation of Poly(ε-caprolactone), Poly(L-lactic acid) and their Blends with Poly(3-hydroxy-butyrate) Studied by TGA/FT-IR Spectroscopy

Summary: The thermal degradation behavior of poly(ε-caprolactone) (PCL) and poly(L-lactic acid) (PLA) have been studied in different environment. It was found that these polymers undergo completely different degradation processes in nitrogen and oxygen atmosphere. In oxygen environment PCL and PLA mainly decompose to CO₂, CO, water and short-chain acids. In nitrogen atmosphere PCL releases 5-hexenioc acid, CO₂, CO and ε-caprolactone, whereas PLA decomposes to acetaldehyde, CO₂, CO and lactide. The polymer blends of poly(3-hydroxybutyrate) (PHB) with PCL and PLA decompose similar to the individual homopolymers with crotonic acid as the initial decomposition product of PHB.     

Energy relationship and the polarization of C_(60) cage in the endohedral complexes (X@C_(60))

In this paper, we carry out the calculation on the system (X@C60)(X=Li, Na, K, Kb, Cs; F, Cl, Br, I), where the position of X changes along 5 typical symmetry directions. For the calculation of quantum chemistry we use EHMO/ASED method, for the calculation of molecular mechanics we use Buckingham potential (exp-6-1) function, and for the calculation of thermo-chemical cycle we use individually isolating the processes such as the structure variation, charge transfer and charge distribution, and their interactions etc. The calculation results show that (1) In the region of radius r≈0.2 nm of the Ceo cage, the potential field is nearly spherical; (2) Except for Li and Na, the systems are the most stable with minimum energies at the center of C60 cage. For Li and Na, the systems are the most stable with minimum energies at r≈0.16 nm and r≈0.13 nm, respectively. In view of the interactive region of chemical bonds, the interactions between X and the C60 cage do not belong to the classical chemical bonds; (     

铜在3%NaCl溶液中腐蚀行为的光电化学研究

Cu以其优异的导电性、导热性和易加工性广泛用于工农业生产中．自然Cu的腐蚀和防腐成为人们很关注的问题．人们已经注意到，Cl-对Cu的腐蚀有影响，并进行过一些研究．但目前使用光电化学方法研究这一问题的文章尚不多见，特别是利用测量开路光电压及其瞬态波形这一现场的、无损的、灵敏的监测方法研究户对Cu电极腐蚀全过程的文章尚未见到．本文正是利用如上方法及XPS，AES方法，研究了Cl-对Cu电极腐蚀的全过程，取得了一些有意义的结果．1实验方法Cu电极用99．99％（质量分数）的Cu制成，面积约为39mm2；电极底部由Cu导线焊接引出，…     

Spectrophotometric study of Cd(II), Pb(II), Hg(II) and Zn(II) complexes with 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin

The reaction of 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin (TCPP) with Cd(II), Pb(II), Hg(II) and Zn(II) was studied spectrophotometrically and kinetics, equilibrium constants as well as photodecomposition of complexes were determined. It was verified that these metal ions with large radius accelerate the incorporation reaction of zinc into TCPP. On the basis of the mechanism and kinetics of this reaction, a sensitive method for the spectrophotometric determination of trace amounts of Zn(II) has been developed. The molar absorptivity of examined Zn-TCPP complex and Sandell's sensitivity at 423 nm were 3.5×10⁵ M⁻¹ cm⁻¹ and 18.3 ng cm⁻². The detection limit for the recommended procedure was 1.4×10⁻⁹ M (0.9 ng ml⁻¹) and precision in range 20-100 ng ml⁻¹ not exceeds 2.7% RSD. The proposed method applied for zinc determination in natural waters and nutritional supplement was compared with AAS results and declared value.