单金属双中心Ti-MCM-41分子筛催化剂的光催化性能

 制备了单金属双中心Ti－MCM－41分子筛催化剂，通过XRD、低温N2吸附－脱附、XPS及原子吸收光谱等对催化剂进行了表征．结果表明，单金属双中心Ti－MCM－41分子筛催化剂具有良好的长程有序结构和孔结构，其比表面积大于1000m2／g，孔径分布窄，最可几孔径为2．7nm；Ti的电子结合能为458．6eV，介于骨架Ti（选择性氧化活性中心）和非骨架Ti（光催化活性中心）之间．以H2O2和·OH的生成量为基准，考察了Ti－MCM－41对苯羟化反应的催化性能随光照时间、催化剂用量、加水量、反应温度和空气流速等条件的变化，得出了光催化反应的最佳条件．在无外加氧化剂的情况下，单金属双中心Ti－MCM－41上苯的转化率为0．2％，表明其确实具有一定的光催化性能，可实现光催化－选择性氧化的反应－反应耦合．与骨架取代Ti－MCM－41和MCM－41负载TiO2催化剂相比，单金属双中心Ti－MCM－41的催化活性最高．这主要是由于它既具有光催化活性中心，又具有选择性氧化活性中心．     

MoO3在介孔分子筛MCM—41上分散状况的研究

采用XPS和XRD方法,测定了MoO3在未经改性的MCM－41及用Al2O3和TiO2改性后的MCM－41上的单层分散阈值,发现,MoO3在用Al2O3和TiO2改性后的MCM－41上的单层分散阈值比未经改性的MCM－41上的要提高三分之二。另外,借助MoO3/MCM-41、MoO3/Al2O3-MCM-41、MoO3/TiO2-MCM-41系列样品的比表面积和孔分布测定,研究了MoO3在未经改性的MCM－41及用Al2O3和TiO2改性后的MCM－41上的分散状况。     

TiO~2修饰的介孔分子筛MCM-41的合成、表征及光 催化性研究

首次以三种不同的含钛有机物为氧化钛的前驱体,合成了三种TiO~2呈单层分散状态的TiO~2修饰的介孔分子筛MCM-41,并以XRD,FT-IR,液氮温度下N~2吸附-脱附曲线,固体UV-vis漫反射等表征手段对其结构特征和氧化钛分散状态进行了研究。TiO~2在介孔分子筛MCM-41孔道中分散,MCM-41仍能保持骨架结构,没有晶相TiO~2生成;TiO~2与MCM-41孔道表面的≡Si－OH以化学键连接,生成Si－O－Ti键;TiO~2在MCM-41内孔壁呈均匀单层分散状态;TiO~2粒子的减小使其对紫外光的吸收发生明显的蓝移现象。并以苯酚降解反应为模型检验合成的具有光催化性的TiO~2修饰的MCM-41的光催化活性。     

以硅胶和三氯化钛为原料合成Ti-MCM-41分子筛 Ⅱ. Ti-MCM-41分子筛的表征

 利用N2吸附,TG－DTA,FT－IR,UV－Vis和UV－Raman光谱等技术对以硅溶胶和TiCl3水溶液为原料合成的中孔Ti－MCM－41分子筛的孔结构和钛的配位状态进行了详细的表征．N2吸附等温线表明,Ti－MCM－41分子筛的孔径比纯硅MCM－41分子筛小,钛的加入使分子筛的单胞体积大大增加,比表面积和孔壁厚度也显著增大．TG－DTA结果表明,Ti－MCM－41分子筛中存在着两种不同的模板剂键合位．FT－IR,UV－Vis及UV－Raman光谱表明,Ti原子存在于分子筛骨架中且以四面体方式配位,没有结晶状态的TiO2形成．     

TiO2修饰ＭＣＭ—４１的结构表征及光催化苯酚降解活性

以钛酸丁酯为前驱体,合成了呈单层和双层分散状态的ＴiO2修饰的介孔人子筛ＭＣＭ－４１,用ＸＲＤ,液氮温度下Ｎ２吸附－脱附曲线,ＦＴ－ＩＲ和固体ＵＶ－Ｖis漫反射等手段对其结构特征和氧化钛分 散状态进行了表征,以苯酚降解为模型反应,考察了具有光催化活性的ＴiO2修饰的ＭＣＭ－４１的光催化活性。     

MCM-41分子筛负载钼钴系催化剂的程序升温硫化研究

采用程序升温硫化（TPS）技术，研究了负载于MCM－41分子筛的钼钴系催化剂的性能，根据TPOS结果可知，（1）载体和MoO3相互作用的强度顺序如下：Al2O3＞Al2O3-MCM-41＞MCM－41＞TiO2－MCM－41，说明TiO2具有削弱MCM－41和MoO3作用的能力；而Al2O3则相反，它增加了MoO3和MCM－41的相互作用。（2）助剂CoO对负载于未经改性的MCM－41载体上的MoO3的硫化没有明显的促进作用，这和以Al2O3为载体的情况下不同，在Al2O3上，MoO3和CoO可能生成Co-Mo－O复合相，从而促进了MoO3的硫化。（3）助剂CoO对负载于经TiO2和Al2O3改性的MCM－41上的MoO3的硫化起了促进作用。     

表面修饰DBS基团对TiO2气相光催化性能的影响

采用溶胶-水热法直接获得表面修饰十二烷基苯磺酸钠(DBS)分子基团的TiO2纳米粒子, 并考察了DBS表面修饰对纳米TiO2光催化氧化降解气相n-C5H12反应的活性和寿命的影响, 并利用表面光电压(SPS)谱和光致发光(PL)光谱等方法研究了DBS表面修饰的影响机制. 结果表明, 表面修饰DBS分子基团能够抑制TiO2纳米微晶生长, 促进纳米TiO2分散, 增强吸附性和提高光生电荷分离, 使光催化活性显著提高. 但寿命并未下降, 这与TiO2和DBS基团的光稳定性有关. 动力学研究结果表明, TiO2光催化氧化n-C5H12反应遵循Langmuir-Hinshelwood动力学模型, 为准一级反应.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

RE/TiO2用于NO2-光催化氧化的研究

 以稀土盐和钛酸丁酯为原料,采用溶胶－凝胶法制备了掺杂稀土\r\n光催化剂RE／TiO2（RE＝La,Ce,Er,Pr,Gd,Nd,Sm）,并用XRD,\r\nDRS和IR等手段对RE／TiO2进行了表征;以NO－2为目标降解物,考察了\r\n其光催化氧化活性．结果表明,适量RE的掺入,可有效扩展TiO2的光谱\r\n响应范围,有利于NO－2的吸附,使光催化活性均有不同程度的提高．\r\n其中掺杂Gd样品的光催化活性最高．掺杂量是影响光催化活性的重要因\r\n素,一般最佳掺杂量为w（RE）≈0．5％．     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶.凝胶法将TiO2担载在介孔MCM-41分子筛上,制备了不同TiO2含量的系列TiO2/MCM-41复合材料,利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征.TiO2的晶型为锐钛矿相,复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小,TiO2的平均粒径随其担载量的增加而增大.以罗丹明B的光催化降解为探针反应,评价了TiO2/MCM-41复合材料的光催化降解活性.结果表明,在紫外光照射下,罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学,复合材料对罗丹明B的光催化降解活性明显高于商用TiO2(P-25),复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

多酸修饰二氧化钛纳米管复合膜的制备、表征及其光催化降解甲基橙的研究

采用电沉积方法制备了H3PW12O40(PW12)-TiO2复合膜,通过SEM,EDX和XRD等手段,对其组成和结构进行了表征,并考察了该复合膜催化剂对降解甲基橙的催化活性.实验结果表明PW12存在于TiO2纳米管结构中,用PW12多酸修饰的TiO2纳米管比单独的TiO2纳米管展示出更好的光催化性能,由于电子能够从TiO2纳米管导带转移到多酸的LUMO能级,有效抑制了光生电子和空穴的复合,因而使PW12-TiO2复合膜表现出更高的光催化活性.     

Enhanced electrochemiluminescence sensor from tris(2,2'-bipyridyl)ruthenium(II) incorporated into MCM-41 and an ionic liquid-based carbon paste electrode

The electrochemiluminescence (ECL) of tris(2,2'-bipyridyl)ruthenium(II) [Ru(bpy)(3)(2+)] ion-exchanged in the sulfonic-functionalized MCM-41 silicas was developed with tripropylamine (TPrA) as a co-reactant in a carbon paste electrode (CPE) using a room temperature ionic liquid (IL) as a binder. The sulfonic-functionalized silicas MCM-41 were used for preparing an ECL sensor by the electrostatic interactions between Ru(bpy)(3)(2+) cations and sulfonic acid groups. We used the IL as a binder to construct the CPE (IL-CPE) to replace the traditional binder of the CPE (T-CPE)--silicone oil. The results indicated that the MCM-41-modified IL-CPE had more open structures to allow faster diffusion of Ru(bpy)(3)(2+) and that the ionic liquid also acted as a conducting bridge to connect TPrA with Ru(bpy)(3)(2+) sites immobilized in the electrode, resulting in a higher ECL intensity compared with the MCM-41-modified T-CPE. Herein, the detection limit for TPrA of the MCM-41-modified IL-CPE was 7.2 nM, which was two orders of magnitude lower than that observed at the T-CPE. When this new sensor was used in flow injection analysis (FIA), the MCM-41-modified IL-CPE ECL sensor also showed good reproducibility. Furthermore, the sensor could also be renewed easily by mechanical polishing whenever needed.     

Preparation and Acid Catalytic Activity of TiO2 Grafted Silica MCM-41 with Sulfate Treatment

TiO2 grafted silica MCM-41 catalyst with and without sulfate treatment were prepared. The structural and acid properties of these materials were investigated by XRD, N2 adsorption-desorption, element analysis, thermal analysis, Raman and FTIR measurements. Their acid-catalytic activities were evaluated using the cyclization reaction of pseudoionone. It was found that the obtained materials possess well-ordered mesostructure, and the grafted TiO2 components were in highly dispersed amorphous form. T/MCM41 without sulfation contained only Lewis acid sites, while Br?nsted and Lewis acidities were remarkably improved for the sulfated materials ST/MCM41 and d-ST/MCM41. T/MCM-41 was not active for the cyclization reaction of pseudoionone, but ST/MCM-41 and d-ST/MCM-41 possessed favorable catalytic activities. The catalytic performance of ST/MCM-41 was comparable with that of the commercial solid acid catalyst of Amberlyst-15, and better than that of d-ST/MCM-41, although the latter underwent a second TiO2 grafting process and accordingly had higher Ti and S content. The specific surface structure of Si-O-Ti-O-S=O in ST/MCM-41 and the bilateral induction effect of Si and S=O on Si-O-Ti bonds were speculated to account for its higher acid catalytic activity.     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

BiVO4-MCM-41复合催化剂的制备及其对亚甲基蓝降解的光催化活性

将单斜白钨矿结构的BiVO4固载于中孔MCM-41分子筛上,制备了BiVO4-MCM-41复合催化剂,并对催化剂进行了表征,考察了催化剂在光催化亚甲基蓝降解反应中的催化活性.结果表明,BiVO4首先在MCM-41分子筛上形成锆石结构或四面体白钨矿结构的结晶,通过水热处理之后转变为单斜结构的结晶.BiVO4-MCM-41催化剂不仅保持了BiVO4较高的光催化活性,而且提高了对亚甲基蓝的吸附性能,从而提高了对亚甲基蓝降解反应的光催化活性.     

Characterization of Pore Structure and Coordination of Titanium in TiO(2) and SiO(2)-TiO(2) Sol-Pillared Clays

Titania sol-pillared clay (TiO(2) PILC) and silica-titania sol-pillared clay (SiO(2)-TiO(2) PILC) were synthesized by the sol-gel method. Supercritical drying (SCD) and treatment with quaternary ammonium surfactants were used to tailor the pore structure of the resulting clay. It was found that SCD approach increased the external surface area of the PILCs dramatically and that treatment with surfactants could be used to tailor pore size because the mesopore formation in the galleries between the clay layers follows the templating mechanism as observed in the synthesis of MCM-41 materials. Highly mesoporous solids were thus obtained. In calcined TiO(2) PILC, ultrafine crystallites in anatase phase, which are active for photocatalytic oxidation of organics, were observed. In SiO(2)-TiO(2) PILCs and their derivatives, titanium was highly dispersed in the matrix of silica and no crystal phase was observed. The highly dispersed titanium sites are good catalytic centers for selective oxidation of organic compounds. Copyright 2001 Academic Press.     

新戊基钛在MCM-41表面的接枝反应及产物性质

采用原位红外光谱法在真空系统中考察了MCM-41分子筛表面与四新戊基钛Ti(CH2CMe3)4的反应,发现这个反应可在室温下定量进行,得到表面新戊基钛(≡Si－O)2Ti(CH2CMe3)2. 这种表面新戊基钛很容易与CH3OH、H2O和O2进一步发生反应分别得到(≡Si－O)2Ti(OCH3)2、(≡Si－O)2Ti(OH)2和(≡Si－O)2Ti(OCH2CMe3)2等表面化合物.在氧气中焙烧由(≡Si－O)2Ti(CH2CMe3)2水解所得的(≡Si－O)2Ti(OH)2可制得表面含钛MCM-41介孔分子筛（Ti-MCM-41）.元素分析、低温N2吸附-脱附、紫外可见漫反射光谱、X射线粉末衍射和FTIR等表征结果表明,接枝反应和后续的处理不破坏分子筛的介孔结构; Ti-MCM-41的比表面积和孔直径较MCM-41略有降低; Ti原子在Ti-MCM-41表面以TiO4四面体配位状态分散,并对乙烯氧化有较明显的光催化活性.论文还通过对Ti-MCM-41与水热合成骨架含钛[Ti]-MCM-41结构和光催化活性的比较,对分子筛类材料光催化作用机制进行了分析探讨.     

A mesoporous silica nanoparticles immobilized open-tubular capillary column with a coating of cellulose tris(3,5-dimethylphenyl-carbamate) for enantioseparation in CEC

An approach of immobilizing mobile crystalline material (MCM)-41 mesoporous silica nanoparticles on the inner wall of an open-tubular (OT) capillary as the support for coating chiral selector of cellulose tris(3,5-dimethylphenyl-carbamate) (CDMPC) was carried out. By taking advantage of the improved phase ratio of OT capillary with the immobilization of MCM-41 mesoporous material, the cellulose derivative of CDMPC as the chiral selector was simply coated on the MCM-41 nanoparticle layer via the hydrogen-bonding interaction, and the enantioseparation was successively carried out. Eight pairs of acidic, neutral and basic enantiomers were resolved in capillary electrochromatography or capillary liquid chromatography mode. The concentration of CDMPC for coating was systematically investigated to obtain the optimized chromatographic properties on enantioseparation by controlling the supposed film thickness of CDMPC on MCM-41 nanoparticle layer. Comparing with a bare fused silica capillary column coated with CDMPC under the same coating procedure as MCM-41-modified capillary did, the MCM-41-modified capillary column offered much higher enantioselectivity. This result indicated the significance of using the mesoporous nanoparticles as the electrochromatographic support to enhance the phase ratio of OT capillary column in capillary electrochromatography and capillary liquid chromatography. For investigating the effect of experimental conditions on the enantioseparation with this prepared OT capillary column, the content of organic modifier acetonitrile in the mobile phase was thus extensively evaluated to achieve a better chiral separation.