TiO2光催化分解水制氢研究进展

综述了近几年改善TiO2光催化分解水制氢的方法措施.向水中添加供电子物质可减少光生电子与空穴的复合,添加碳酸盐或碘化物有利于光生电子与空穴分离;TiO2表面沉积适量的金属颗粒也有利于实现电子和空穴分离,但沉积太多的金属颗粒不但降低TiO2对光的吸收而且还可能成为光生电荷复合的中心;掺杂合适的金属离子通过形成杂质能级可把TiO2的吸光范围至拓宽可见光,掺杂非金属元素使TiO2的带隙(Eg)变窄,从而使TiO2的吸光红移更明显,但掺杂离子有可能成为光生电荷复合的中心;染料敏化或半导体复合有利于实现电荷分离,提高光电转换效率.将多种修饰方法有机结合起来制取氢足目前的一个研究方向,最后分析了未来的研究重点.     

镧在TiO2薄膜中的非均匀掺杂对光催化性能的影响

采用溶胶-凝胶法制备了La^3＋非均匀掺杂的TiO2薄膜。通过对甲基橙的光催化降解实验来评价催化剂薄膜的催化活性，结果表明：La^3＋的掺杂方式对TiO2的催化活性有很大的影响，采用非均匀掺杂方式可以明显提高TiO2的催化活性，掺杂浓度以0．5％（原子分数）为最佳。紫外-可见漫反射光谱鼎示其吸收带边明显红移；电化学行为表明其光生空穴一电子对的形成能力和分离效率得到提高。通过比较太阳能光电池异质结的“窗口效应”理论，初步探讨了La^3＋非均匀掺杂对TiO2的光催化活性的影响机制。     

Co~(2+)掺杂的纳米TiO_2薄膜光催化特性及电化学阻抗谱研究

本文采用交流电沉积技术,在多孔氧化铝模板中合成出Co2+掺杂的纳米TiO2薄膜(Co2+/TiO2薄膜)。以次甲基蓝为降解物,研究了纳米Co2+/TiO2薄膜在可见光下的催化性能,考察了阳极偏压对光催化活性的影响。用电化学阻抗谱(EIS)研究了纳米Co2+/TiO2薄膜在次甲基蓝溶液中的电化学行为,给出了相应的等效电路和半导体能带结构参数-空间电荷层宽度。研究表明,适量Co2+掺杂可以提高TiO2薄膜的光催化活性。在Co2+/TiO2膜电极上施加一定阳极偏压,使空间电荷层宽度增加,因此能有效实现光生电子-空穴分离,进一步提高次甲基蓝的光催化降解效率。     

Fe3+/V5+/TiO2复合纳米微粒光催化性能的研究

采用溶胶凝胶法制备了Fe^3 /V^5 /TiO2复合纳米微粒作为光催化剂。光降解反应结果表明，其掺杂催化剂Fe^3 /V^5 /TiO2的光催化活性明显提高。光电化学研究显示，铁离子可以成为电荷陷阱，促进空穴的界面传递反应。适量钒离子掺杂使TiO2电极的光电流升高，导带中电子浓度的增大，加快了界面的电子传递反应。共掺杂催化剂中，Fe^3 、V^5 分别提供了空穴与电子的陷阱，同时加快了电子与空穴的界面传递反应，从 更有效地提高光催化活性。双组份共掺杂为提高TiO2光催化活性提供新的途径。     

Sm掺杂对TiO2薄膜光催化性能的影响

 采用溶胶-凝胶法、浸渍-提拉法制备了不同形式和不同含量Sm掺杂的锐钛矿晶型TiO2的光催化剂薄膜. 采用X射线衍射、UV-Vis光谱及电化学实验对所制得的TiO2光催化剂薄膜进行了表征,并通过甲基橙溶液的光催化降解实验评价了其光催化活性. 结果表明,与未掺杂的TiO2薄膜相比,Sm掺杂的TiO2薄膜的UV-Vis吸收光波长向长波方向移动,并且光照开路电压也相应提高; 适量Sm掺杂可以明显提高TiO2薄膜的光催化活性,最佳Sm掺杂量为x(Sm3+)=0.5%; 在各种掺杂形式中以表层Sm掺杂的Sm-TiO2(S)薄膜的光催化活性最好. 讨论了Sm掺杂提高TiO2薄膜光催化活性的机理.     

掺杂铈对玻璃表面TiO_2薄膜上油酸光催化降解的影响

采用旋转涂膜工艺 ,以溶胶 凝胶法在玻璃表面制备了掺杂铈的TiO2 薄膜 .利用高压液相色谱、紫外 可见光分光光度计、扫描电镜和能谱仪等手段对掺杂铈的TiO2 薄膜进行了表征 ,考察了掺杂铈对油酸光催化降解效率及TiO2 薄膜表面晶粒分布的影响 ,并对薄膜的化学成分进行了定性和定量分析 .结果表明 ,掺杂 3%Ce的TiO2 薄膜对油酸有最高的光催化降解效率 ,40 0℃为掺杂铈TiO2 薄膜的最佳热处理温度     

TiB2/均相硼掺杂TiO2核/壳结构提升光催化氧化水产氧活性

光催化可实现污染物降解、分解水制氢和CO2还原等多种氧化还原反应, 因而受到了广泛关注. 光催化材料中光生电荷的数目与氧化还原能力直接影响光催化反应效率, 在许多光催化反应中, 光生空穴氧化反应被认为速控步骤. 以光催化分解水为例, 质子的还原是单电子过程, 水氧化产生氧气则涉及四个电子. 空穴的高能量不仅可赋予其高的氧化能力,还能提高其迁出表面的能力, 因此具有重要研究价值.我们组的前期工作表明, 以TiB2作为前驱体, 采用水热合成和焙烧两步法可制备出间隙硼掺杂的金红石相或锐钛矿相TiO2, 间隙硼掺杂可显著降低价带顶, 提升光催化氧化水产氧性能. 然而, 在已有的结果中, 间隙硼掺杂浓度在TiO2中均呈现从内向外逐渐增加的梯度分布, 这意味着硼掺杂浓度有限, 且表层更低的价带顶不利于体相光生空穴向表面迁移, 因此亟需实现TiO2中均相的间隙硼掺杂.本文以湿化的氩气为水解环境, 将水解过程限域在TiB2的表面以减少硼原子流失; 同时提高水解温度, 使残留的硼原子形成间隙掺杂, 避免其在二次焙烧时扩散, 从而在TiB2核的表面所形成的TiO2壳层中实现均相间隙硼掺杂, 显著提高了光催化氧化水产氧活性. 多种表征结果表明, 直径约为6-10 μm的TiB2核表面形成了厚约400 nm的TiO2壳层, 在TiO2/TiB2中TiO2壳层重量比约为30%, TiO2壳层中锐钛矿相TiO2占比为65 wt%, 金红石相TiO2占比为35 wt%. TiO2壳层中间隙硼为均相分布, 硼掺杂显著降低了价带顶位置, 提高了光生空穴的氧化能力, 从而使得TiB2/TiO2展现出比未掺杂的金红石、锐钛矿相及两者混合相的TiO2均具有更高的光催化氧化水产氧的能力.     

光电流法研究TiO2薄膜表面吸附氧对光催化活性的影响

采用溶胶-凝胶法制备了锐钛矿型和金红石型TiO2薄膜, 利用光电流和XPS技术研究了薄膜表面吸附氧对不同晶型TiO2光催化活性的影响. 并通过降解纯的环己烷溶液的实验来评估不同晶型TiO2的光催化活性. 结果表明, 在相同条件下, 锐钛矿型TiO2比金红石型具有明显的光催化活性. 这是由于锐钛矿型TiO2比金红石型TiO2具有较强的吸附氧的能力, 同时其光生电子与空穴的复合率相对较小所致.     

离子掺杂改性纳米TiO_2光催化剂的研究进展

以纳米TiO2为代表的纳米半导体光催化材料是目前研究的热点。纳米TiO2为宽禁带半导体,需紫外光激发;而且,产生的光生电子-空穴对极易复合,限制了其实际应用。将纳米TiO2进行离子掺杂改性是解决上述问题的有效途径。目前离子掺杂改性纳米TiO2光催化剂的研究进展表明,采用两种离子共掺杂改性纳米TiO2时,离子之间会产生协...     

具有高光催化活性的黑色TiO2（B）/锐钛矿双晶TiO2-x纳米纤维

高效TiO2基光催化材料的开发一直是催化领域的研究热点,主要的策略是如何有效地分离光生载流子.制备多晶相的TiO2材料可引入异质/相结结构使电子与空穴朝不同方向移动,从而避免电子与空穴复合;另外,在TiO2中掺杂其他金属或非金属也可以有效地降低电子与空穴的复合率,掺杂的元素作为电子捕获阱俘获光生电子,以实现电子空穴的有效分离.近些年,作为一种全新的掺杂剂,氧空穴可以有效改善TiO2的光催化活性,所制TiO2具有可见光的全光谱吸收能力,因此该类TiO2呈现出黑色.通过上述方法均可以制备出高活性TiO2基光催化材料,如果能够将这些方法耦合一起,则可能制备出活性更高的光催化剂.因此,本文将异相结结构和空穴掺杂耦合起来,用多孔钛酸盐衍生物在H2中高温焙烧制得一种全新的黑色TiO2(B)/锐钛矿双晶TiO2–x纳米纤维.不同于其他TiO2基光催化材料,该样品仅由Ti和O元素组成,通过Ti和O元素的组合,形成了双晶结构和空穴掺杂两种特殊的结构,借助场发射(FESEM)、拉曼光谱(Raman)、氮气物理吸脱附、X射线光电子能谱(XPS)、热重(TG)、紫外可见漫反射光谱(UV-Vis)和荧光光谱(PL)等表征分析了样品的结构及其光催化性能间构效关系. FESEM结果显示,黑色TiO2(B)/锐钛矿双晶TiO2–x为长1–5mm、宽0.2mm的纤维结构, Raman结果表明,锐钛矿相在特征波段(140 cm–1左右)和TiO2(B)的特征波段(220–260 cm–1)均发生蓝移,说明该两相中均存在氧空穴;该样表面未检测到Ti3+,因此氧空穴可能分散在TiO2(B)和锐钛矿相的体相中.根据黑色TiO2(B)/锐钛矿双晶TiO2–x和白色TiO2(B)/锐钛矿双晶TiO2的失重差,估算出前者的O/Ti原子比为1.97.光催化降解甲基橙实验结果显示,黑色TiO2(B)/锐钛矿双晶TiO2–x的光催化活性是白色双晶TiO2的4.2倍,锐钛矿TiO2的10.5倍,且连续反应10次后未出现失活现象,显示出了良好的光催化稳定性.前期,我们已经证明了白色TiO2(B)/锐钛矿双晶TiO2由于具有TiO2(B)和锐钛矿的异相结结构,致使其电子空穴有效地分离,从而表现出优异的光催化活性;本文的PL结果显示,由于氧空穴的引入,异相结与氧空穴两者共同作用,进一步促进了黑色TiO2(B)/锐钛矿双晶TiO2–x电子与空穴的有效分离,因此黑色TiO2(B)/锐钛矿双晶TiO2–x表现出高的光催化活性.由于其特殊的结构,黑色TiO2(B)/锐钛矿双晶TiO2–x纳米纤维将在环境与能源领域表现出良好的应用前景.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.