Rh基催化剂上CO加氢制C2含氧化物的原位红外光谱研究

 用原位红外光谱考察了Rh-Mn-Li-Fe/SiO2和Rh/SiO2催化剂表面上CO的吸附态及CO加氢反应过程中吸附物种的变化. 结果表明,CO在Rh/SiO2催化剂上仅有线式吸附态存在,而CO在Rh-Mn-Li-Fe/SiO2催化剂上既有线式吸附态存在,又有孪生吸附态存在. 这说明Rh-Mn-Li-Fe/SiO2催化剂中Rh的分散度较高. 经CO加氢反应(3.0 MPa,593 K)后,在Rh-Mn-Li-Fe/SiO2催化剂上可观测到C2含氧化物前驱物种的吸收谱带,而在Rh/SiO2催化剂上未观测到相应的谱带; CO在这两种催化剂上主要以线式吸附态存在,孪生吸附态基本消失. 结合催化剂对CO加氢的催化性能,可以认为线式吸附的CO对生成C2含氧化物有贡献. Rh-Mn-Li-Fe/SiO2催化剂的高活性是由于助剂的存在削弱了其表面吸附CO的 C-O键,促进了CO的活化,从而有利于C2含氧化物前驱物的生成.     

Elucidating the Structural Composition of an Fe–N–C Catalyst by Nuclear‐ and Electron‐Resonance Techniques

Fe–N–C catalysts are very promising materials for fuel cells and metal–air batteries. This work gives fundamental insights into the structural composition of an Fe–N–C catalyst and highlights the importance of an in‐depth characterization. By nuclear‐ and electron‐resonance techniques, we are able to show that even after mild pyrolysis and acid leaching, the catalyst contains considerable fractions of α‐iron and, surprisingly, iron oxide. Our work makes it questionable to what extent FeN₄ sites can be present in Fe–N–C catalysts prepared by pyrolysis at 900 °C and above. The simulation of the iron partial density of phonon states enables the identification of three FeN₄ species in our catalyst, one of them comprising a sixfold coordination with end‐on bonded oxygen as one of the axial ligands.     

Catalytically Active Rh Sub‐Nanoclusters on TiO2 for CO Oxidation at Cryogenic Temperatures

The discovery that gold catalysts could be active for CO oxidation at cryogenic temperatures has ignited much excitement in nanocatalysis. Whether the alternative Pt group metal (PGM) catalysts can exhibit such high performance is an interesting research issue. So far, no PGM catalyst shows activity for CO oxidation at cryogenic temperatures. In this work, we report a sub‐nano Rh/TiO₂ catalyst that can completely convert CO at 223 K. This catalyst exhibits at least three orders of magnitude higher turnover frequency (TOF) than the best Rh‐based catalysts and comparable to the well‐known Au/TiO₂ for CO oxidation. The specific size range of 0.4–0.8 nm Rh clusters is critical to the facile activation of O₂ over the Rh–TiO₂ interface in a form of Rh?O?O?Ti (superoxide). This superoxide is ready to react with the CO adsorbed on TiO₂ sites at cryogenic temperatures.     

Non‐Oxidative Methane Conversion Using Lead‐ and Iron‐Modified Albite Catalysts in Fixed‐Bed Reactor

Raw and modified albite catalysts, including Pb/Albite and Fe/Albite catalysts, have been investigated for methane conversion to C₂ hydrocarbons under non‐oxidative conditions. Introduction of Pb to albite improved the activity and selectivity to non‐coke products. Based on characterization, it was found that Pb entered into the alkali and alkaline‐earth metal sites of albite, while partial Fe doped in the tetrahedron sites and the other loaded on the surface of albite. At the reaction temperature of 1073 K, methane gas hourly space velocity (GHSV) of 2 L·gcat^–1·h^–1, catalyst dosage of 0.25 g (300 mesh), the methane conversion catalyzed by raw albite in the fixed‐bed micro reactor exhibited a methane conversion of 3.32%. Notably, introducing a Pb content of 3.4 wt% into albite greatly enhanced the conversion of methane up to 8.19%, and the selectivity of C₂ hydrocarbons reached 99% without any coke under the same reaction conditions. While Fe‐doping could weakly heighten the methane conversion to 3.97%, and coke was formed. Thus, a comparison of Pb/Albite and Fe/Albite catalysts demonstrates that the catalytic activity of albite is mainly decided by alkali and alkaline‐earth metal sites, and lead‐modification can effectively improve the catalytic activity of albite.     

CO加氢制C2含氧化合物Rh基催化剂中常见助剂的作用

由煤、天然气或生物质出发,经合成气制乙醇等C2含氧化合物具有重要意义,负载型Rh基催化剂是实现该过程最有效的催化剂。助剂的选择尤其重要,其中Fe、Mn、Li的助催化作用最为显著,人们对此进行了长期而有效的研究,有关观点也很难统一,但相关总结性的报道不多。因此,本文系统综述了这三种常见助剂催化作用的研究进展。结果表明,这些助剂的作用与其所处的催化体系、制备方法等密切相关,后者直接影响了助剂-金属-载体间相互作用,使得催化剂各种组分表现出不同存在状态,进而影响它们在CO加氢各基元步骤中的催化作用。本文可为人们全面认识这些常用助剂的作用提供有益的参考。     

Metal‐Ion Metathesis in Metal–Organic Frameworks: A Synthetic Route to New Metal–Organic Frameworks

A porous metal–organic framework, Mn(H₃O)[(Mn₄Cl)₃(hmtt)₈] (POST‐65), was prepared by the reaction of 5,5′,10,10′,15,15′‐hexamethyltruxene‐2,7,12‐tricarboxylic acid (H₃hmtt) with MnCl₂ under solvothermal conditions. POST‐65(Mn) was subjected to post‐synthetic modification with Fe, Co, Ni, and Cu according to an ion‐exchange method that resulted in the formation of three isomorphous frameworks, POST‐65(Co/Ni/Cu), as well as a new framework, POST‐65(Fe). The ion‐exchanged samples could not be prepared by regular solvothermal reactions. The complete exchange of the metal ions and retention of the framework structure were verified by inductively coupled plasma–atomic emission spectrometry (ICP‐AES), powder X‐ray diffraction (PXRD), and Brunauer–Emmett–Teller (BET) surface‐area analysis. Single‐crystal X‐ray diffractions studies revealed a single‐crystal‐to‐single‐crystal (SCSC)‐transformation nature of the ion‐exchange process. Hydrogen‐sorption and magnetization measurements showed metal‐specific properties of POST‐65.     

Structural Characterization of Alumina‐Supported Rh Catalysts: Effects of Ceriation and Zirconiation by using Metal–Organic Precursors

The effects of the addition of ceria and zirconia on the structural properties of supported rhodium catalysts (1.6 and 4 wt % Rh/γ‐Al₂O₃) are studied. Ceria and zirconia are deposited by using two preparation methods. Method I involves the deposition of ceria on γ‐Al₂O₃ from Ce(acac)₃, and the rhodium metal is subsequently added, whereas method II is based on a controlled surface reaction technique, that is, the decomposition of metal–organic M(acac)_x (in which M=Ce, x=3 and M=Zr, x=4) on Rh/γ‐Al₂O₃. The structures of the prepared catalyst materials are characterized ex situ by using N₂ physisorption, transmission electron microscopy, high‐angle annular dark‐field scanning transmission election microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray photoelectron spectroscopy (XPS), and X‐ray absorption fine structure spectroscopy (XAFS). All supported rhodium systems readily oxidize in air at room temperature. By using ceriated and zirconiated precursors, a larger rhodium‐based metallic core fraction is obtained in comparison to the undoped rhodium catalysts, suggesting that ceria and zirconia protect the rhodium particles against extensive oxidation. XPS results indicate that after the calcination and reduction treatments, a small amount of chlorine is retained on the support of all rhodium catalysts. EXAFS analysis shows significant Rh? Cl interactions for Rh/Al₂O₃ and Rh/CeO_x/Al₂O₃ (method I) catalysts. After reaction with H₂/He in situ, for series of samples with 1.6 wt % Rh, the EXAFS first shell analysis affords a mean size of approximately 30 atoms. A broader spread is evident with a 4 wt % rhodium loading (ca. 30–110 atoms), with the incorporation of zirconium providing the largest particle sizes.     

Ultrahigh‐Loading Zinc Single‐Atom Catalyst for Highly Efficient Oxygen Reduction in Both Acidic and Alkaline Media

Atomically dispersed Zn–N–C nanomaterials are promising platinum‐free catalysts for the oxygen reduction reaction (ORR). However, the fabrication of Zn–N–C catalysts with a high Zn loading remains a formidable challenge owing to the high volatility of the Zn precursor during high‐temperature annealing. Herein, we report that an atomically dispersed Zn–N–C catalyst with an ultrahigh Zn loading of 9.33 wt % could be successfully prepared by simply adopting a very low annealing rate of 1° min^?1. The Zn–N–C catalyst exhibited comparable ORR activity to that of Fe–N–C catalysts, and significantly better ORR stability than Fe–N–C catalysts in both acidic and alkaline media. Further experiments and DFT calculations demonstrated that the Zn–N–C catalyst was less susceptible to protonation than the corresponding Fe–N–C catalyst in an acidic medium. DFT calculations revealed that the Zn–N₄ structure is more electrochemically stable than the Fe–N₄ structure during the ORR process.     

A DFT study of DMC formation on Rh‐doped Cu/AC surfaces

The activity and selectivity of heterogeneous catalysts can be significantly improved by dispersion of another active component in the metal substrate. The impact of Rh promoter on the formation of dimethyl carbonate (DMC) via oxidative carbonylation of methanol on Cu–Rh/AC (activated carbon) catalyst was investigated by density functional theory calculations. The most stable configurations of reacting species (CO, OH, CH₃O, monomethyl carbonate, and DMC) adsorbed on the Cu⁰(zero‐valent copper)/AC and Cu–Rh/AC surfaces were determined on the basis of the calculated results. The reaction energy and activation energy of the rate‐limiting steps on the Cu–Rh/AC and Cu⁰/AC surfaces were compared. The activation energies of the rate‐limiting step of CO insertion into dimethoxide are 206.3 and 304.8 kJ mol^?1 on the Cu–Rh/AC and Cu⁰/AC surfaces, respectively. The activation energies of the rate‐limiting step of CO insertion into methoxide are 78.5 and 92.7 kJ/mol on the Cu–Rh/AC and Cu⁰/AC surfaces, respectively. The calculated results indicate that the addition of Rh atom has a significant effect on decreasing the active energy the main pathway for DMC formation. © 2015 Wiley Periodicals, Inc.     

Co-doping a metal (Cr,Mn, Fe,Co, Ni,Cu, and Zn) on Mn/ZSM-5 catalyst and its effect on the catalytic reduction of nitrogen oxides with ammonia

Selective catalytic reduction (SCR) of NO_x by NH₃ over a series of Mn–M/Z catalysts (M = Cr, Mn, Fe, Co, Ni, Cu, Zn, and Z = the ZSM-5 Zeolite) synthesized by wet impregnation method was investigated. Mn–Fe/Z, Mn–Co/Z, and Mn–Cu/Z catalysts exhibited approximately 100 % NO_x conversion over a wide temperature range (200–360 °C) in a defined atmospheric condition, which was noticeably greater than that of Mn–Cr/Z (340–360 °C). Furthermore, the effect of addition of second metal oxide species to the initial Mn/Z catalyst on the structure of catalysts was studied by several characterization techniques. BET measurements revealed high surface area and pore volume of the Mn–Cu/Z catalyst. In addition, the XRD and UV–Vis DR results showed that addition of co-doped metal oxide species improved the dispersion of metal ions and inhibited crystallization of metal oxides. UV–Vis studies also were in good accordance with DTA/TG results confirming the formation of cobalt oxide and copper oxide clusters in Mn–Co/Z and Mn–Cu/Z catalysts, respectively. The FTIR spectra of pyridine adsorption, in addition, suggested the Mn–Cu/Z catalyst contained the most Lewis acid sites leading to more NO_x adsorption capacity.     

Development of an Improved Rhodium Catalyst for Z‐Selective Anti‐Markovnikov Addition of Carboxylic Acids to Terminal Alkynes

To develop more active catalysts for the rhodium‐catalyzed addition of carboxylic acids to terminal alkynes furnishing anti‐Markovnikov Z enol esters, a thorough study of the rhodium complexes involved was performed. A number of rhodium complexes were characterized by NMR, ESI‐MS, and X‐ray analysis and applied as catalysts for the title reaction. The systematic investigations revealed that the presence of chloride ions decreased the catalyst activity. Conversely, generating and applying a mixture of two rhodium species, namely, [Rh(DPPMP)₂][H(benzoate)₂] (DPPMP=diphenylphosphinomethylpyridine) and [{Rh(COD)(μ₂‐benzoate)}₂], provided a significantly more active catalyst. Furthermore, the addition of a catalytic amount of base (Cs₂CO₃) had an additional accelerating effect. This higher catalyst activity allowed the reaction time to be reduced from 16 to 1–4 h while maintaining high selectivity. Studies on the substrate scope revealed that the new catalysts have greater functional‐group compatibility.     

On the Influence of Oxygen on the Degradation of Fe‐N‐C Catalysts

Fe‐N‐C catalysts containing atomic FeN_x sites are promising candidates as precious‐metal‐free catalysts for oxygen reduction reaction (ORR) in proton exchange membrane fuel cells. The durability of Fe‐N‐C catalysts in fuel cells has been extensively studied using accelerated stress tests (AST). Herein we reveal stronger degradation of the Fe‐N‐C structure and four‐times higher ORR activity loss when performing load cycling AST in O₂‐ vs. Ar‐saturated pH 1 electrolyte. Raman spectroscopy results show carbon corrosion after AST in O₂, even when cycling at low potentials, while no corrosion occurred after any load cycling AST in Ar. The load‐cycling AST in O₂ leads to loss of a significant fraction of FeN_x sites, as shown by energy dispersive X‐ray spectroscopy analyses, and to the formation of Fe oxides. The results support that the unexpected carbon corrosion occurring at such low potential in the presence of O₂ is due to reactive oxygen species produced between H₂O₂ and Fe sites via Fenton reactions.     

A practical innovative method for highly selective oxidation of alkenes and alkanes using Fe (III) and Mn (III) porphyrins supported onto multi‐wall carbon nanotubes as reusable heterogeneous catalysts

Functionalized multi‐walled carbon nanotubes were used for covalent immobilization of meso‐tetrakis(4‐carboxyphenyl) porphyrinatoiron (III) chloride [Fe (TCPP)Cl] and meso‐tetrakis(4‐carboxyphenyl) porphyrinatomanganese (III) acetate [Mn (TCPP)OAc]. The full characterization of the hybrid porphyrinic nanomaterials, by Fourier transform‐infrared and UV–Vis spectroscopy, transmission electron microscopy, thermogravimetry and flame atomic absorption spectrometry is described. The oxidation of alkenes and alkanes with molecular oxygen as green oxidant in the presence of Mn‐ and Fe‐catalysts has been studied in a comparative manner. The Fe‐catalyst was shown to have higher catalytic activity compared with the Mn‐catalyst. In addition, both separable solid catalysts can be recovered and reused at least 10 times along with good yields.     

High efficiency of Mn–Ce‐modified TiO2 catalysts for the low‐temperature oxidation of Hg0 under a reducing atmosphere

Manganese‐ and cerium oxide‐modified titania catalysts were prepared by the deposition precipitation for the removal of elemental mercury (Hg⁰) from simulated yellow phosphorus off‐gas at low temperature. In addition, these catalysts were characterized by X‐ray diffraction, Brunauer–Emmett–Teller measurements, X‐ray photoelectron spectroscopy and field‐emission scanning electron microscope to determine the surface morphology of the obtained compounds and explore their formation mechanism. The results revealed that a Mn–Ce loading and reaction temperature of 10% and 150 °C, respectively, as well as a Mn/Ce molar ratio of 2:1, led to an optimal efficiency for the oxidation of elemental mercury. Furthermore, the effects of flue gas components were investigated. The presence of O₂ clearly promoted the oxidation of Hg⁰. A CO atmosphere did not affect the Hg⁰ oxidation, when compared with N₂, whereas the presence of H₂S and water vapor inhibited the oxidation process. Furthermore, the X‐ray photoelectron spectroscopy spectra of Hg 4f revealed that the elemental mercury adsorbed by the catalyst is present as HgO. Finally, the Hg⁰ catalytic oxidation mechanism was discussed on the basis of the experimental results and characterization analysis.     

Insight into the Mechanism of Hydrogenation of Amino Acids to Amino Alcohols Catalyzed by a Heterogeneous MoOx‐Modified Rh Catalyst

Hydrogenation of amino acids to amino alcohols is a promising utilization of natural amino acids. We found that MoO_x‐modified Rh/SiO₂ (Rh–MoO_x/SiO₂) is an efficient heterogeneous catalyst for the reaction at low temperature (323 K) and the addition of a small amount of MoO_x drastically increases the activity and selectivity. Here, we report the catalytic potential of Rh–MoO_x/SiO₂ and the results of kinetic and spectroscopic studies to elucidate the reaction mechanism of Rh–MoO_x/SiO₂ catalyzed hydrogenation of amino acids to amino alcohols. Rh–MoO_x/SiO₂ is superior to previously reported catalysts in terms of activity and substrate scope. This reaction proceeds by direct formation of an aldehyde intermediate from the carboxylic acid moiety, which is different from the reported reaction mechanism. This mechanism can be attributed to the reactive hydride species and substrate adsorption caused by MoO_x modification of Rh metal, which results in high activity, selectivity, and enantioselectivity.     

Iron Carbide Nanoparticles Encapsulated in Mesoporous Fe‐N‐Doped Carbon Nanofibers for Efficient Electrocatalysis

Exploring low‐cost and high‐performance nonprecious metal catalysts (NPMCs) for oxygen reduction reaction (ORR) in fuel cells and metal–air batteries is crucial for the commercialization of these energy conversion and storage devices. Here we report a novel NPMC consisting of Fe₃C nanoparticles encapsulated in mesoporous Fe‐N‐doped carbon nanofibers, which is synthesized by a cost‐effective method using carbonaceous nanofibers, pyrrole, and FeCl₃ as precursors. The electrocatalyst exhibits outstanding ORR activity (onset potential of ?0.02 V and half‐wave potential of ?0.140 V) closely comparable to the state‐of‐the‐art Pt/C catalyst in alkaline media, and good ORR activity in acidic media, which is among the highest reported activities of NPMCs.     

Polymerization of 3‐ethynylthiophene with homogeneous and heterogeneous Rh catalysts

3‐Ethynylthiophene (3ETh) was polymerized with Rh(I) complexes: [Rh(cod)acac], [Rh(nbd)acac], [Rh(cod)Cl]₂, and [Rh(nbd)Cl]₂ (cod is η²:η²‐cycloocta‐1,5‐diene and nbd η²:η²‐norborna‐2,5‐diene), used as homogeneous catalysts and with the last two complexes anchored on mesoporous polybenzimidazole (PBI) beads: [Rh(cod)Cl]₂/PBI and [Rh(nbd)Cl]₂/PBI used as heterogeneous catalysts. All tested catalyst systems give high‐cis poly(3ETh). In situ NMR study of homogeneous polymerizations induced with [Rh(cod)acac] and [Rh(nbd)acac] complexes has revealed: (i) a transformation of acac ligands into free acetylacetone (Hacac) occurring since the early stage of polymerization, which suggests that this reaction is part of the initiation, (ii) that the initiation is rather slow in both of these polymerization systems, and (iii) a release of cod ligand from [Rh(cod)acac] complex but no release of nbd ligand from [Rh(nbd)acac] complex during the polymerization. The stability of diene ligand binding to Rh‐atom in [Rh(diene)acac] catalysts remarkably affects only the molecular weight but not the yield of poly(3ETh). The heterogeneous catalyst systems also provide high‐cis poly(3ETh), which is of very low contamination with catalyst residues since a leaching of anchored Rh complexes is negligible. The course of heterogeneous polymerizations is somewhat affected by limitations arising from the diffusion of monomer inside catalyst beads. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2776–2787, 2008     

Single‐Atom Cr−N4 Sites Designed for Durable Oxygen Reduction Catalysis in Acid Media

Single‐atom catalysts (SACs) are attracting widespread interest for the catalytic oxygen reduction reaction (ORR), with Fe?N_x SACs exhibiting the most promising activity. However, Fe‐based catalysts suffer serious stability issues as a result of oxidative corrosion through the Fenton reaction. Herein, using a metal‐organic framework as an anchoring matrix, we for the first time obtained pyrolyzed Cr/N/C SACs for the ORR, where the atomically dispersed Cr is confirmed to have a Cr?N₄ coordination structure. The Cr/N/C catalyst exhibits excellent ORR activity with an optimal half‐wave potential of 0.773 V versus RHE. More excitingly, the Fenton reaction is substantially reduced and, thus, the final catalysts show superb stability. The innovative and robust active site for the ORR opens a new possibility to circumvent the stability issue of the non‐noble metal ORR catalysts.     

Development of a Continuous‐Flow System for Asymmetric Hydrogenation Using Self‐Supported Chiral Catalysts

Well‐designed, self‐assembled, metal–organic frameworks were constructed by simple mixing of multitopic MonoPhos‐based ligands ( 3 ; MonoPhos=chiral, monodentate phosphoramidites based on the 1,1′‐bi‐2‐naphthol platform) and [Rh(cod)₂]BF₄ (cod=cycloocta‐1,5‐diene). This self‐supporting strategy allowed for simple and efficient catalyst immobilization without the use of extra added support, giving well‐characterized, insoluble (in toluene) polymeric materials ( 4 ). The resulting self‐supported catalysts ( 4 ) showed outstanding catalytic performance for the asymmetric hydrogenation of a number of α‐dehydroamino acids ( 5 ) and 2‐aryl enamides ( 7 ) with enantiomeric excess (ee) ranges of 94–98 % and 90–98 %, respectively. The linker moiety in 4 influenced the reactivity significantly, albeit with slight impact on the enantioselectivity. Acquisition of reaction profiles under steady‐state conditions showed 4 h and 4 i to have the highest reactivity (turnover frequency (TOF)=95 and 97 h^?1 at 2 atm, respectively), whereas appropriate substrate/catalyst matching was needed for optimum chiral induction. The former was recycled 10 times without loss in ee (95–96 %), although a drop in TOF of approximately 20 % per cycle was observed. The estimation of effective catalytic sites in self‐supported catalyst 4 e was also carried out by isolation and hydrogenation of catalyst–substrate complex, showing about 37 % of the Rh^I centers in the self‐supported catalyst 4 e are accessible to substrate 5 c in the catalysis. A continuous flow reaction system using an activated C/ 4 h mixture as stationary‐phase catalyst for the asymmetric hydrogenation of 5 b was developed and run continuously for a total of 144 h with >99 % conversion and 96–97 % enantioselectivity. The total Rh leaching in the product solution is 1.7 % of that in original catalyst 4 h .     

One‐Pot Cooperation of Single‐Atom Rh and Ru Solid Catalysts for a Selective Tandem Olefin Isomerization‐Hydrosilylation Process

Realizing the full potential of oxide‐supported single‐atom metal catalysts (SACs) is key to successfully bridge the gap between the fields of homogeneous and heterogeneous catalysis. Here we show that the one‐pot combination of Ru₁/CeO₂ and Rh₁/CeO₂ SACs enables a highly selective olefin isomerization‐hydrosilylation tandem process, hitherto restricted to molecular catalysts in solution. Individually, monoatomic Ru and Rh sites show a remarkable reaction specificity for olefin double‐bond migration and anti‐Markovnikov α‐olefin hydrosilylation, respectively. First‐principles DFT calculations ascribe such selectivity to differences in the binding strength of the olefin substrate to the monoatomic metal centers. The single‐pot cooperation of the two SACs allows the production of terminal organosilane compounds with high regio‐selectivity (>95 %) even from industrially‐relevant complex mixtures of terminal and internal olefins, alongside a straightforward catalyst recycling and reuse. These results demonstrate the significance of oxide‐supported single‐atom metal catalysts in tandem catalytic reactions, which are central for the intensification of chemical processes.