环氧硅烷室温交联丙烯酸酯共聚无皂水溶胶的研究 Ⅰ.环氧硅氧烷微乳液的制备

环氧硅烷室温交联丙烯酸酯共聚无皂水溶胶的研究 Ⅰ.环氧硅氧烷微乳液的制备     

单体极性对甲基丙烯酸甲酯／丙烯酸丁酯／甲基丙烯酸钠无皂乳液共聚？…

研究了少量甲基丙烯酸钠存在下单体极性对甲基丙烯酸甲酯／丙烯酸丁酯无皂乳液共聚合的影响。单体极性降低，使粒径减小，聚合整编提高，乳液表面张力和粘度降低，粒子表面电荷密度增大，聚合物分子量提高。ＭＭＡ／ＮａＭＡ无皂乳液聚合物只呈现一个玻璃化温度Ｔｇ，ＢＡ／ＮａＭＡ无皂乳液聚合物呈现两个Ｔｇ，ＭＭＡ／ＢＡ比为２：１－１：２的ＭＭＡ／ＢＡ／ＮａＭＡ无皂乳液聚合物呈现四个Ｔｇ，这是由于粒子外机相对富含ＯＳＯ     

含氟丙烯酸酯共聚乳液的制备及表征

采用十二烷基硫酸钠和壬基酚聚氧乙烯醚(OP-10)混合乳化剂，制备了粒径为40-50nm的甲基丙烯酸全氟辛基乙酯(FMA8)-甲基丙烯酸丁酯(BMA)-甲基丙烯酸(MA)共聚物乳液。通过DSC、、FTIR、^1H-NMR等手段对共聚物进行了表征。考察了乳液的稳定性、乳胶膜的吸水性和耐溶剂性以及全氟单体的含量对聚合反应的影响。     

含氟丙烯酸酯共聚乳液及其膜表面特性的研究

以十二烷基硫酸钠 (SDS)和OP 10混合乳化剂 ,制备了甲基丙烯酸全氟辛基乙酯 (FMA8) 甲基丙烯酸丁酯 (BMA) 甲基丙烯酸 (MAA)共聚乳液 .通过DSC、FT IR、1 H NMR对共聚物的结构、组成进行了表征研究 .采用JZHY 180界面张力仪研究了共聚乳液膜表面的性质 ,结果表明 ,随着共聚物中全氟单体含量的增加 ,共聚物膜的表面能显著降低 ,当全氟单体的含量达到 2 5wt %时 ,其表面能降低到 19 74mJ m2 .X ray光电子能谱(XPS)对共聚物表面原子组成的分析结果表明 ,共聚物表面氟的含量远高于其平均含量 ,证明了含氟基团的趋表现象 .经退火处理 ,共聚物膜表面的氟含量增加 ,表面自由能降低     

丙烯酸酯-苯胺共聚乳液的制备及防腐蚀性能

采用两步乳液聚合法制备丙烯酸酯-苯胺共聚乳液.通过红外光谱(FT-IR)、X射线衍射(XRD)、热重分析(TGA)和透射电镜(TEM)等表征手段对产物的结构进行了研究.将共聚乳液涂覆在Q235低碳钢表面,利用电化学交流阻抗谱(EIS)、塔菲尔(Tafel)曲线和平衡开路电位(OCP)考察共聚乳液涂层对Q235低碳钢的腐蚀防护性能.结果表明:丙烯酸酯与苯胺之间形成了化学键,丙烯酸酯乳液有效地起到了掺杂酸的作用;共聚乳液具有良好的成膜性;共聚乳液涂层具有较高的交流阻抗值(3.0×105Ω·cm2),降低了金属的腐蚀电流密度(10-8 A/cm2),显著提高了腐蚀电位(-0.44 V),防腐蚀性能较好.     

环氧硅氧烷对丙烯酸酯类无皂涂料性能的影响

无皂乳液涂料;环氧硅氧烷对丙烯酸酯类无皂涂料性能的影响     

MMA/BA/AA/HEMA无皂乳液共聚物的力学性能研究

采用分步控温、结合种子乳液共聚法,合成了ＭＭＡ／ＢＡ／ＡＡ／ＨＥＭＡ无皂乳液共聚折。对共聚物的应力－应变行为和动态力学性能分别进行了研究。实验结果反映出ＭＭＡ／ＢＡ、ＡＡ、ＨＥＭＡ以及名加助剂含量对共聚物相结构、力学有显著的影响。随着ＭＭＡ含量增加,共聚物出现微相分离,断裂强度升高,伸长率降低。随着体系极性基团的增多,相分离趋势加大,这些实验结果揭示了共聚物宏观性能与微观结构间的内在联系。     

自交联型含氟丙烯酸酯共聚物的合成与表征

含氟丙烯酸酯;自交联;无皂乳液;接触角滞后     

全氟烷基乙基丙烯酸酯共聚物的制备和表面性质

皮革和纺织品等的防水防油处理一直是人们关注的课题 ,用普通防水剂处理皮革和纺织品只能防水不能防油 ,达不到彻底防污 .由于有机氟化物的表面能极低 ,而丙烯酸酯类高分子具有成膜性好、网络结构较为疏松的特点 ,因此通过在聚丙烯酸酯高分子侧链引入全氟烷基 [1～ 5] 制得的全氟烷基丙烯酸酯共聚物 ,具有优异的防水、防油和防污功能 ,并且可使处理的制品保持原有的色泽、手感和透气性等优点 .本文采用乳液共聚法制得了全氟烷基乙基丙烯酸酯共聚物 [6] ,通过测定接触角计算了共聚物的表面自由能为 0 .0 1 2 6J/m2 ,这比作为目前优良品种的…     

MMA/BA/双官能团单体无皂共聚乳液的稳定性

用马来酸酐和(聚)乙二醇合成了一系列双官能团共单体,将其用于MMA/BA无皂乳液共聚合.研究了共单体的空间效应、用量、加料方式对其无皂乳液稳定性的影响.用适当的共单体和半连续加料方式,可得到较稳定的乳液,粒径分布接近单分散.凝聚物的生成机理主要是失稳凝聚和架桥凝聚.     

Characterization of a low-wettable surface based on perfluoroalkyl acrylate copolymers

The low-wettable surfaces based on perfluoroalkyl acrylate (FA)/n-alkyl acrylate copolymers with various amounts of FA units were presented to analyze their surface properties. The FA copolymers were prepared by soap-free emulsion polymerization in the presence of sodium 2-acrylamide-2-methyl propanesulfonate (AMPSNa) used as a reactive surfactant. Low-wettability properties resulted from the self-assembly of fluorine-containing side chains, surface density and extent of orientation of perfluoroalkyl (R_F) groups. The wetting behavior of the low-wettable surfaces was discussed from a standpoint of dynamic contact angles measurement, which implied an enrichment of perfluoroalkyl groups on the topmost surface. Increased R_F surface densities and orientation, measured by attenuated total reflectance spectra of infrared (ATR-IR), X-ray photoelectron spectroscopy (XPS) and scanning force microscopy (SFM), respectively, were consistent with higher angles.     

Studies on the Preparation of Stable and High Solid Content Emulsifier-Free Poly(MMA/BA/HEA) Latex with the Addition of AMPS and Characterization of the Obtained Copolymers

The 2-acrylamido -2-methylpropane sulfonic acid (AMPS) was used as a reactive comonomer for the methyl methacrylate (MMA), n-butyl acrylate (BA) and 2-hydroxyethyl acrylate (HEA) emulsifier-free emulsion copolymerization system to obtain latices of stable and high-solid content (50 wt%).The polymerization and storage process is very stable, and the emulsion could store at room temperature for more than six months with the addition of AMPS. Properties of the latices, such as stability, flow behavior, particles diameter and morphology were studied. In addition, physical properties of the obtained copolymers, such as water resistance, glass transition temperature (T_g) were also investigated. The final size of the latex particles is 200～300 nm in diameter. Compared with the copolymers that were prepared by surfactant emulsion polymerization water resistance is greatly improved.     

Hydrophobic and Oleophobic Epoxy Surfaces Prepared by a Facile Process with Fluorosilicone Copolymer and SiO2 Nano-Particle

Hydrophobic and oleophobic surfaces with multi-scale structures were prepared on epoxy coating surfaces by using a facile process with fluorosilicone copolymer and SiO₂ nano-particles. The fluorosilicone copolymers were synthesized using perfluoroalkyl acrylate (FA), vinyltriethoxysilane (VTES) and styrene (St) as comonomers via radical emulsion polymerization. In this paper, the surface properties of epoxy coating modified by fluorosilicone copolymer and SiO₂ nano-particles were analyzed by using the contact angle measurement. The results showed that the modified epoxy coating surface exhibited not only excellent hydrophobicity but also oleophobicity, the water contact angle reached as high as 149° and the oil (atoleine) contact angle 101°, respectively.     

不饱和端基超支化聚合物/丙烯酸酯共聚乳液的研究

利用Si—H加成反应制得了以CC为端基的超支化含硅聚合物,并将其与丙烯酸酯类单体进行乳液共聚,对聚合反应机理及所得聚合物的性能进行了测试分析.结果表明,含有大量CC端基的超支化含硅聚合物能与丙烯酸酯类单体稳定聚合,制得了平均粒径小于100nm高度交联的乳胶粒子.共聚物的红外光谱证实,超支化聚合物的不饱和端基已全部反应,形成了以超支化聚合物为多臂交联点的交联型乳胶粒子.随聚合体系中超支化聚合物用量的增加,乳液聚合反应速率增大,乳胶粒粒径减小,共聚物热稳定性显著提高.     

Effect of different surfactants on colloidal and polymer properties of fluorinated acrylate latex

Fluorinated acrylate latex was successfully prepared by semi-continuous seeded emulsion polymerization of dodecafluoroheptyl methacrylate (DFMA) with butyl acrylate (BA), methyl methacrylate (MMA) initiated by potassium persulfate in the water. The resultant latexes and their films are characterized with Fourier transform infrared (FTIR) spectrometry, contact angle determinator, dynamic light scattering detector and surface tension determinator. Effect of different surfactants on colloidal and polymer properties of fluorinated acrylate latex was studied. Results show that the latex prepared with sodium dodecyl benzene sulfonate surfactant has the smallest particle size and contact angle but the moderate surface tension. The latex prepared with perfluorooctanesulfonic acid potassium surfactant has the smallest surface tension, moderate particle size but the biggest contact angle. The latex prepared with sodium 2-hydroxy-3-(methacryloyloxy) prop- ane-1-sulfonate surfactant has the biggest particle size and surface tension but moderate contact angle. In addition, the latex prepared with sodium 2-hydroxy-3-(methacryloyloxy) prop- ane-1-sulfonate has higher electrolyte stability.     

Suspended Emulsion Copolymerization of Acrylonitrile with Methyl Acrylate: Effects of Reaction Parameters on the Polymerization

Acrylonitrile/methyl acrylate copolymers were synthesized by suspended emulsion polymerization with water as dispersed phase and monomers as continuous phase, potassium peroxydisulphate (KPS) as initiator, Span-80 as emulsifier, and poly(vinyl alcohol) (PVA) as suspending agent. Effects of reaction parameters such as water/monomer mass ratio, concentration of initiator, polymerization temperature and agitation rate on polymerization conversion and the particle size distribution of acrylonitrile/methyl acrylate copolymers were studied. It was found that polymerization conversion increased with an increase of water/monomer mass ratio, concentration of initiator and polymerization temperature, while the agitation rate had no significant effect on the polymerization conversion. Particle size distribution became narrower with an increase of water/monomer mass ratio and agitation rate. Under the same initiator concentration and polymerization temperature, particle size distribution became wider along with polymerization time. The differential scanning calorimetry (DSC) results indicated that the peak temperature of the copolymers decreased with increasing MA content.     

Stability of Emulsion Polymerization of New Fluorinated Acrylate Emulsion and Its Characterization

The new fluorinated acrylate emulsion was synthesized by using the intermediate perfluorous nonene and 2-hydroxyethyl methacrylate as the staring reactants via semi-continuous seeded emulsion polymerization. The structures, glass transition temperature, thermal property and water repellency of the fluorinated acrylate emulsion were characterized with FTIR, differential scanning calorimetry, thermal analysis, and contact angle meter. Influences of many factors such as the theoretical solid content, the temperature of the emulsion polymerization on the stability of the emulsion polymerization, the added amount of emulsifiers and the added amount of the initiator were studied. Results show that the stability of the emulsion polymerization is fairly good when the theoretical solid content is below 30% and the reaction temperature is 80°C and the added amount of emulsifiers and the initiator are 6.0–8.0% and 2.0% respectively. In comparison with the acylate emulsion, the thermal stability of the fluorinated acrylate emulsion is decreased but the water repellency of the fluorinated acrylate emulsion is greatly increased.     

光致变色含氟丙烯酸酯涂层的制备及性能

选取十二烷基硫酸钠(SDS),辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,过硫酸钾(KPS)为引发剂,将2-(全氟己基)乙基甲基丙烯酸酯(PFM)与丙烯酸酯类单体采用预乳化-半连续种子乳液聚合法进行乳液共聚,再将羟基螺吡喃(SPOH)与乳液进行物理共混,制得光致变色含氟丙烯酸酯乳液。 通过多种表征手段研究丙烯酸正丁酯(n-BA)和甲基丙烯酸甲酯(MMA)软硬单体的质量比,SPOH的用量对聚合反应和乳胶膜性能的影响。 结果表明,加入含氟单体后乳胶膜与水、油的接触角提高,热稳定性提高;加入SPOH的质量分数为1.25%时,乳胶膜具有较好的光致变色性能。     

Preparation of MMA－BA－DMAEMA Nanosized Latex

The terpolymer latex of methyl methacrylate (MMA)/butyl acrylate (BA)/ dimethyl aminoethyl methacrylate (DMAEMA) with diameter of less than 100 nm was prepared by seeding semi-continuous emulsion copolymerization using APS (ammonium pcrsulfate) / TMEDA (N,N,N,N-tetramethylethylenediamine) as the redox initiators and SDS (sodium dodecylsulfate) and OP (P-octylpolyethylene glycol phenylether) as co-emulsifiers. The factors that influenced the process stability of the copolymerization and the particle size of the latex were investigated. The addition of aqueous ammonia as coagulation inhibitor provided better process stability of the copoly- merization. The addition of acetic acid as the acidification agent caused a remarkable reduction of the latex particle size.