Elimination of 4‐chlorophenol in aqueous solution by the Novel Pd/MIL‐101(Cr)‐Hydrogen‐Accelerated catalytic fenton system

Excessive consumption of Fe (II) and massive generation of sludge containing Fe (III) from classic Fenton process remains a major obstacle for its poor recycling of Fe (III) to Fe (II). Therefore, the MHACF‐MIL‐101(Cr) system, by introducing H₂, Pd⁰ and MIL‐101(Cr) into Fenton reaction system, was developed at normal temperature and pressure. In this system, the reduction of Fe^III back to Fe^II by solid catalyst Pd/MIL‐101(Cr) for the storage and activation of H₂, was accelerated significantly by above 10‐fold and 5‐fold controlled with the H₂‐MIL‐101(Cr) system and H₂‐Pd⁰ system, respectively. However, the concentration of Fe (II) generated by the reduction of Fe (III) could not be detected with the only input of H₂ and without the addition of MOFs material. In addition, the apparent consumption of Fe (II) in MHACF‐MIL‐101(Cr) system was half of that in classical Fenton system, while more Fe (II) might be reused infinitely in fact. Accordingly, only trace amount of Fe (II) vs H₂O₂ concentration was needed and hydroxyl radicals through the detection of para‐hydroxybenzoic acid (p‐HBA) as the oxidative product of benzoic acid (BA) by·OH could be continuously generated for the effective degradation of 4‐chlorophenol(4‐CP). The effects of initial pH, concentration of 4‐CP, dosage of Fe²⁺, H₂O₂ and Pd/MIL‐101(Cr) catalyst, Pd content and H₂ flow were investigated, combined with systematic controlled experiments. Moreover, the robustness and morphology change of Pd/MIL‐101(Cr) were thoroughly analyzed. This study enables better understanding of the H₂‐mediated Fenton reaction enhanced by Pd/MIL‐101(Cr) and thus, will shed new light on how to accelerate Fe (III)/Fe (II) redox cycle and develop more efficient Fenton system.     

Magnetic Bistability of Isolated Giant‐Spin Centers in a Diamagnetic Crystalline Matrix

Polynuclear single‐molecule magnets (SMMs) were diluted in a diamagnetic crystal lattice to afford arrays of independent and iso‐oriented magnetic units. Crystalline solid solutions of an Fe₄ SMM and its Ga₄ analogue were prepared with no metal scrambling for Fe₄ molar fractions x down to 0.01. According to high‐frequency EPR and magnetic measurements, the guest SMM species have the same total spin (S=5), anisotropy, and high‐temperature spin dynamics found in the pure Fe₄ phase. However, suppression of intermolecular magnetic interactions affects magnetic relaxation at low temperature (40 mK), where quantum tunneling (QT) of the magnetization dominates. When a magnetic field is applied along the easy magnetic axis, both pure and diluted (x=0.01) phases display pronounced steps at evenly spaced field values in their hysteresis loops due to resonant QT. The pure Fe₄ phase exhibits additional steps which are firmly ascribed to two‐molecule QT transitions. Studies on the field‐dependent relaxation rate showed that the zero‐field resonance sharpens by a factor of five and shifts from about 8 mT to exactly zero field on dilution, in agreement with the calculated variation of dipolar interactions. The tunneling efficiency also changes significantly as a function of Fe₄ concentration: the zero‐field resonance is significantly enhanced on dilution, while tunneling at ±0.45 T becomes less efficient. These changes were rationalized on the basis of a dipolar shuffling mechanism and transverse dipolar fields, whose effect was analyzed by using a multispin model. Our findings directly prove the impact of intermolecular magnetic couplings on SMM behavior and disclose the magnetic response of truly isolated giant spins in a diamagnetic crystalline environment.     

Yolk–shell microspheres assembled from Preyssler‐type NaP5W30O11014− polyoxometalate and MIL‐101(Cr) metal–organic framework: A new inorganic–organic nanohybrid for fast and selective removal of cationic organic dyes from aqueous media

Novel inorganic–organic yolk–shell microspheres based on Preyssler‐type NaP₅W₃₀O₁₁₀^14? polyoxometalate and MIL‐101(Cr) metal–organic framework (P₅W₃₀/MIL‐101(Cr)) were synthesized by reaction of K_12.5Na_1.5[NaP₅W₃₀O₁₁₀], Cr(NO₃)₃·9H₂O and terephthalic acid under hydrothermal conditions at 200°C for 24 h. The as‐prepared yolk–shell microspheres were fully characterized using various techniques. All analyses confirmed the incorporation of the Preyssler‐type NaP₅W₃₀O₁₁₀^14? polyoxometalate into the three‐dimensional porous MIL‐101(Cr) metal–organic framework. The results revealed that P₅W₃₀/MIL‐101(Cr) demonstrated rapid adsorption of cationic methylene blue (MB) and rhodamine B (RhB) with ultrahigh efficiency and capacity, as well as achieving rapid and highly selective adsorption of MB from MB/MO (MO = methyl orange), MB/RhB and MB/RhB/MO mixtures. The P₅W₃₀/MIL‐101(Cr) adsorbent not only exhibited a high adsorption capacity of 212 mg g^?1, but also could quickly remove 100% of MB from a dye solution of 50 mg l^?1 within 8 min. The effects of some key parameters such as adsorbent dosage, initial dye concentration and initial pH on dye adsorption were investigated in detail. The equilibrium adsorption data were better fitted by the Langmuir isotherm. The adsorption kinetics was well modelled using a pseudo‐second‐order model. Also, the inorganic–organic hybrid yolk–shell microspheres could be easily separated from the reaction system and reused up to four times without any change in structure or adsorption ability. The stability and robustness of the adsorbent were confirmed using various techniques.     

Solvato Modulation of the Magnetic Memory in Isotopically Enriched Erbium Polyoxometalate

Single-Molecule Magnet (SMM) property is by essence molecular, while commonly measured in solid crystalline state. Solvent crystallization molecules are usually neglected in the analysis and interpretation of solid-state properties. The solvation/desolvation process in the polyoxometalate(POM)-based Na₉[Er(W₅O₁₈)₂] ⋅ 35 H₂O SMM demonstrates that the dehydrated form relaxes more than 1000 times faster than the initial state, while the rehydration process allows the quasi complete recovering of the initial magnetic behaviour. This dehydration process is monitored by thermogravimetric analysis (TGA) and temperature-dependent X-ray powder diffraction, and rationalized by periodic quantum chemical calculations evidencing the tremendous role of the labile water molecules in the stability of the edifice. Ab-initio calculations highlight that sodium ions localization in the structure drive the magnetic responses. Isotopic enrichment with nuclear spin free (¹⁶⁶Er, I=0) Er^III ions shows that the relaxation dynamics in the quantum regime depends on the nuclear spin.     

One‐step synthesized magnetic MIL‐101(Cr) for effective extraction of triazine herbicides from rice prior to determination by liquid chromatography‐tandem mass spectrometry

The magnetic metal‐organic framework MIL‐101(Cr) material‐based solid‐phase extraction method coupled with high‐performance liquid chromatography and tandem mass spectrometry was applied to extract seven triazine herbicides in rices. Fe₃O₄/MIL‐101(Cr) was synthesized using reduction‐precipitation method, in which steps including pre‐synthesis and modification of Fe₃O₄ nanoparticles were by‐passed. Various parameters including extraction solvent type and volume, ultrasonic extraction time, amount of Fe₃O₄/MIL‐101(Cr) microspheres, adsorption time, desorption volume and time were investigated. Under optimal conditions, the proposed method had the limit of detection (S/N = 3) and the limit of quantification (S/N = 10) of 1.08–18.10 and 3.60–60.20 pg/g, respectively. Relative standard deviations calculated for all herbicides with concentrations of 2 and 20 ng/g were in the range of 0.5 to 13% (n = 3). In addition, at the two above‐mentioned concentrations, the method achieved relative recoveries percentages of 79.3 to 116.7% when applied to determine the triazine herbicides in real samples spiked. This rapid, green, non‐polluting, pre‐concentrated extraction method was successfully developed and applied to analyze herbicides in rice samples.     

Long‐Term Photostability in Terephthalate Metal–Organic Frameworks

Prolonged (weeks) UV/Vis irradiation under Ar of UiO‐66(Zr), UiO66 Zr‐NO₂, MIL101 Fe, MIL125 Ti‐NH₂, MIL101 Cr and MIL101 Cr(Pt) shows that these MOFs undergo photodecarboxylation of benzenedicarboxylate (BDC) linker in a significant percentage depending on the structure and composition of the material. Routine characterization techniques such as XRD, UV/Vis spectroscopy and TGA fail to detect changes in the material, although porosity and surface area change upon irradiation of powders. In contrast to BCD‐containing MOFs, zeolitic imidazolate ZIF‐8 does not evolve CO₂ or any other gas upon irradiation.     

Dodecatungstocobaltate heteropolyanion encapsulation into MIL‐101(Cr) metal–organic framework scaffold provides a highly efficient heterogeneous catalyst for methanolysis of epoxides

A heterogeneous catalyst was synthesized by encapsulation of a Keggin‐type heteropolytungstate, potassium dodecatungstocobaltate trihydrate, K₅[CoW₁₂O₄₀]·(Co‐POM), into chromium(III) terephthalate (MIL‐101). Encapsulation was achieved via a ‘build bottle around ship’ strategy in aqueous media, following a hydrothermal method. The structure of the resulting crystalline solid was characterized using X‐ray diffraction, correlated with Fourier transform infrared and UV–visible spectroscopy. The metal content was analysed using optical emission spectroscopy. Transmission electron microscopy was used to measure particle size and N₂ adsorption in a Brunauer–Emmett–Teller instrument to characterize the specific surface area. The catalytic activity was investigated using methanolysis of epoxides under mild conditions as a test reaction. The turnover frequency of the heterogeneous Co‐POM@MIL‐101 catalyst was more than 20 times higher than that of the homogeneous Co‐POM catalyst. The Co‐POM@MIL‐101 catalyst was reused several times with negligible leaching of Co‐POM and with no considerable loss of its initial efficiency. The simplicity of preparation, extraordinary stability and high reactivity make Co‐POM@MIL‐101 an exceptional catalytic matrix that is easily separable from reaction media.     

Encapsulation of a Porous Organic Cage into the Pores of a Metal–Organic Framework for Enhanced CO2 Separation

We present a facile approach to encapsulate functional porous organic cages (POCs) into a robust MOF by an incipient‐wetness impregnation method. Porous cucurbit[6]uril (CB6) cages with high CO₂ affinity were successfully encapsulated into the nanospace of Cr‐based MIL‐101 while retaining the crystal framework, morphology, and high stability of MIL‐101. The encapsulated CB6 amount is controllable. Importantly, as the CB6 molecule with intrinsic micropores is smaller than the inner mesopores of MIL‐101, more affinity sites for CO₂ are created in the resulting CB6@MIL‐101 composites, leading to enhanced CO₂ uptake capacity and CO₂/N₂, CO₂/CH₄ separation performance at low pressures. This POC@MOF encapsulation strategy provides a facile route to introduce functional POCs into stable MOFs for various potential applications.     

Comparisons of glyphosate adsorption properties of different functional Cr‐based metal–organic frameworks

A Cr‐based metal–organic framework, namely, MIL‐101(Cr), was modified with amino (NH₂–) and urea (UR₂–) groups, and the materials were evaluated as adsorbents for glyphosate, and a comparison with commercial activated carbon was also discussed. The effects of the adsorption factors, such as adsorbent concentration, adsorption time, pH and ionic strength were mainly investigated. The results showed that a pseudo‐second‐order rate equation described the adsorption kinetics mechanisms well, while the Langmuir model and the Freundlich model fitted different adsorption isotherms, respectively. Among the adsorbents we studied, NH₂‐MIL‐101(Cr) showed the maximum adsorbing capacity, which is 64.25 mg/g when pH = 3.0, while UR₂‐MIL‐101(Cr) did not reach the best adsorption performance due to the steric hindrance. The work opens up a new way for the modification of metal–organic frameworks for adsorption process.     

Incorporating Polyoxometalates into a Porous MOF Greatly Improves Its Selective Adsorption of Cationic Dyes

Various polyoxometalates (POMs) were successfully immobilized to the mesoporous coordination polymer MIL‐101 resulting in a series of POM–MOF composite materials POM@MIL‐101 (POM=K₄PW₁₁VO₄₀, H₃PW₁₂O₄₀, K₄SiW₁₂O₄₀). These materials were synthesized by a simple one‐pot reaction of Keggin POMs, tetramethylammonium hydroxide (TMAH), terephthalic acid (H₂bdc), and Cr³⁺ ions. XRD, FTIR, thermogravimetric analyses (TG), inductively coupled plasma (ICP) spectrometry, and energy‐dispersive X‐ray spectroscopy (EDX) collectively confirmed the successful combination of POMs and the porous framework. Further, these composites POM@MIL‐101 with different loading of POMs were achieved by variation of the POM dosage. Notably, the uptake capacity of MIL‐101 towards organic pollutants in aqueous solution was significantly improved by immobilization of hydrophilic POMs into cages of MIL‐101. An uptake capacity of 371 mg g^?1, comparable to that of the graphene oxide sponges, and much higher than that of the commercial activated carbon, was achieved at room temperature in 5 min when dipping 20 mg PW₁₁V@MIL‐101 in the methylene blue (MB) solution (100 mL of 100 mg L^?1 MB solution). Further study revealed that the POM@MIL‐101 composite materials not only exhibited a fast adsorption rate towards dye molecules, but also possessed of selective adsorption ability of the cationic dyes in wastewater. For example, the adsorption efficiency of PW₁₁V@MIL‐101 (10 mg) towards MB (100 mL of 10 mg L^?1) could reach 98 % in the initial 5 min, and it could capture MB dye molecules from the binary mixture of the MB and MO with similar size. Also, the POM@MIL‐101 materials could be readily recycled and reused, and no POM leached in the dye adsorption process.     

Self‐Assembly of a Giant Tetrahedral 3 d–4 f Single‐Molecule Magnet within a Polyoxometalate System

A giant tetrahedral heterometallic polyoxometalate (POM) [Dy₃₀Co₈Ge₁₂W₁₀₈O₄₀₈(OH)₄₂(OH₂)₃₀]^56?, which shows single‐molecule magnet (SMM) behavior, is described. This hybrid contains the largest number of 4f ions of any polyoxometalate (POM) reported to date and is the first to incorporate two different 3d–4f and 4f coordination cluster assemblies within same POM framework.     

Dispersive magnetic solid‐phase extraction of phthalate esters from water samples and human plasma based on a nanosorbent composed of MIL‐101(Cr) metal–organic framework and magnetite nanoparticles before their determination by GC–MS

In this study, a magnetic metal–organic framework was synthesized simply and utilized in the dispersive magnetic solid‐phase extraction of five phthalate esters followed by their determination by gas chromatography with mass spectrometry. First, MIL‐101(Cr) was prepared hydrothermally in water medium without using highly corrosive hydrofluoric acid, utilizing an autoclave oven heat supply. Afterward, Fe₃O₄ nanoparticles were decorated into the matrix of MIL‐101(Cr) to fabricate magnetic MIL‐101 nanocomposite. The nanocomposite was characterized by various techniques. The parameters affecting dispersive magnetic solid‐phase extraction efficiency were optimized and obtained as: a sorbent amount of 15 mg; a sorption time of 20 min; an elution time of 5 min; NaCl concentration, 10% w/v; type and volume of the eluent 1 mL n‐hexane/acetone (1:1 v/v). Under the optimum conditions detection limits and linear dynamic ranges were achieved in the range of 0.08–0.15 and 0.5–200 μg/L, respectively. The intra‐ and interday RSD% values were obtained in the range of 2.5–9.5 and 4.6–10.4, respectively. Ultimately, the applicability of the method was successfully confirmed by the extraction and determination of the model analytes in water samples, and human plasma in the range of microgram per liter and satisfactory results were obtained.     

Polyplatinayne/polyoxometalate composite Langmuir‐Blodgett films: Preparation,structural characterization,and potential optoelectronic applications

A new family of organometallic/inorganic composite Langmuir‐Blodgett (LB) films consisting of rigid‐rod polyplatinayne polymer ([Pt‐T(OMe‐Fl)T]_∞ or [Pt‐T(F‐Fl)T]_∞, where the triplet bonds are abbreviated by T, and fluorene ring by Fl) as the π‐conjugated organometallic molecule, polyoxometalate (POM, POM = K₃PMo₁₂O₄₀, H₃PW₁₂O₄₀, or H₆P₂W₁₈O₆₂) of the Keggin and Dawson structures as the inorganic component, and dimethyldioctadecylammonium bromide (DODA) or a mixture of octadecanoic acid (OA) and docosanoic acid (DA) as the auxiliary film‐forming agent were prepared and characterized by π–A isotherms, UV–Vis absorption spectra, photoluminescence spectra, atomic force microscopy imaging, scanning tunneling microscopy, and low‐angle X‐ray diffraction. Our experimental results indicate that steady, even, and ordered Langmuir and LB films are formed in pure water and polyoxometalate subphases. It was shown that the POM molecules are probably embedded inside the polyplatinayne molecules in the LB film structure and they can quench the luminescence of the Pt polyyne. These Pt‐polyyne based LB films display interesting electric conductivity behavior. [Pt‐T(OMe‐Fl)T]_∞/DODA/HPW₁₂ monolayer film shows a good electrical conductivity, and the tunneling current amounts to ±100 nA when the voltage is set at ±8 V. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3193–3206, 2008     

Electrochemical Behavior and Multilayer Assembly Films with Fine Functional Activities of the Sandwich‐Type Polyoxometallate [Sb2W20Fe2O70(H2O)6]8−

The iron‐substituted sandwich‐type polyoxometalate (POM), comprised of the main group element Sb(III) as the central heteroatom, [Sb₂W₂₀Fe₂O₇₀(H₂O)₆]^8? (Sb₂W₂₀Fe₂), is one of the Krebs‐type derivatives. For the first time, the POMs' redox electrochemistry has been elucidated under acidic conditions employing cyclic voltammetry. It exhibited what is believed to be a bielectronic redox couple associated with the two Fe(III) centers followed by four‐electron and two‐electron redox processes, respectively, with these being attributed to redox processes of the tungsten‐oxo framework. The oxidized form of this POM was found to be stable from pH 1.5 to pH 6. Release of the iron centers from the complex, namely demetallization, was observed upon reduction of the Fe(III) sites at room temperature, with an influence of the solution pH being observed. Through the technique of layer‐by‐layer (LBL) assembly, the POM was successfully immobilized on both quartz and glassy carbon electrode (GCE) surfaces by alternate deposition with the polyelectrolyte poly(diallydimethylammonium chloride) (PDDA). Thus‐prepared multilayer films have been characterized by cyclic voltammetry (CV), UV‐vis spectroscopy (UV‐vis) and XPS. The electrocatalytic activities of the multilayer films containing Sb₂W₂₀Fe₂ have been investigated towards the reduction of NO₃^? and IO₃^?. With an increase in the number of Sb₂W₂₀Fe₂ monolayers within the assembly, the catalytic current towards the reduction of IO₃^? was enhanced.     

Fe3O4/MIL‐101(Fe) nanocomposite as an efficient and recyclable catalyst for Strecker reaction

A highly porous metal‐organic framework, MIL‐101(Fe), was prepared by a solvothermal method in the presence of amino‐modified Fe₃O₄@SiO₂ nanoparticles, in order to achieve Fe₃O₄/MIL‐101(Fe) nanocomposite, which was characterized by XRD, FT‐IR, SEM, TEM, BET, and VSM. This hybrid magnetic nanocomposite was employed as heterogeneous catalyst for α‐amino nitriles synthesis through three‐component condensation reaction of aldehydes (ketones), amines, and trimethylsilyl cyanide in EtOH, at room temperature. The recoverability and reusability was admitted for the heterogeneous magnetic catalyst; no significant reduction of catalytic activity was observed even after five consecutive reaction cycles.     

Coordination Polymer Nanobamboos of {FexIn1−x}‐MIL‐88B: Induced Formation of a Virtual In‐MIL‐88B

A precise fabrication of nanobamboo structures made from hybrid coordination polymers of the type {Fe_xIn_1?x}‐MIL‐88B is demonstrated. The compositions of the hybrid coordination polymer nanobamboos of {Fe_xIn_1?x}‐MIL‐88B (x=0.06, 0.19, or 0.75) are regulated by altering the amount of metal ions used in the reactions. Interestingly, the formation of a virtual In‐MIL‐88B (precise structure, {Fe_0.06In_0.94}‐MIL‐88B), which cannot be created in a typical reaction, is induced by the assistance of a Fe‐MIL‐88B structure. The a and c cell parameters of {Fe_0.06In_0.94}‐MIL‐88B are calculated at 10.95 and 19.86 Å, respectively. These values of {Fe_0.06In_0.94}‐MIL‐88B are larger than those of pure Fe‐MIL‐88B owing to the large ionic size of In³⁺ within the framework.     

Sustainable Catalysis: Rational Pd Loading on MIL‐101Cr‐NH2 for More Efficient and Recyclable Suzuki–Miyaura Reactions

Palladium nanoparticles have been immobilized into an amino‐functionalized metal–organic framework (MOF), MIL‐101Cr‐NH₂, to form Pd@MIL‐101Cr‐NH₂. Four materials with different loadings of palladium have been prepared (denoted as 4‐, 8‐, 12‐, and 16 wt %Pd@MIL‐101Cr‐NH₂). The effects of catalyst loading and the size and distribution of the Pd nanoparticles on the catalytic performance have been studied. The catalysts were characterized by using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier‐transform infrared (FTIR) spectroscopy, powder X‐ray diffraction (PXRD), N₂‐sorption isotherms, elemental analysis, and thermogravimetric analysis (TGA). To better characterize the palladium nanoparticles and their distribution in MIL‐101Cr‐NH₂, electron tomography was employed to reconstruct the 3D volume of 8 wt %Pd@MIL‐101Cr‐NH₂ particles. The pair distribution functions (PDFs) of the samples were extracted from total scattering experiments using high‐energy X‐rays (60 keV). The catalytic activity of the four MOF materials with different loadings of palladium nanoparticles was studied in the Suzuki–Miyaura cross‐coupling reaction. The best catalytic performance was obtained with the MOF that contained 8 wt % palladium nanoparticles. The metallic palladium nanoparticles were homogeneously distributed, with an average size of 2.6 nm. Excellent yields were obtained for a wide scope of substrates under remarkably mild conditions (water, aerobic conditions, room temperature, catalyst loading as low as 0.15 mol %). The material can be recycled at least 10 times without alteration of its catalytic properties.     

Highly efficient oxidative cleavage of alkenes and cyanosilylation of aldehydes catalysed by magnetically recoverable MIL‐101

The catalytic activity of magnetically recoverable MIL‐101 was investigated in the oxidation of alkenes to carboxylic acids and cyanosilylation of aldehydes. MIL‐101 was treated with Fe₃O₄ and the prepared catalyst was characterized using Fourier transform infrared spectroscopy, X‐ray diffraction, N₂ adsorption measurements, field emission scanning electron microscopy, energy‐dispersive X‐ray spectroscopy and inductively coupled plasma analysis. The catalytic active sites in this heterogeneous catalyst are Cr³⁺ nodes of the MIL‐101 framework. This heterogeneous catalyst has the advantages of excellent yields, short reaction times and reusability several times without significant decrease in its initial activity and stability in both oxidation and cyanosilylation reactions. Its magnetic property allows its easy separation using an external magnetic field.     

Enhancing photocatalytic activity of titanium dioxide through incorporation of MIL‐53(Fe) toward degradation of organic dye

Photocatalytic activity of titanium(IV) oxide (TiO₂) can be enhanced through modification of its surface‐active sites. Here, iron(III) carboxylate [MIL‐53[Fe]]‐incorporated TiO₂ (as MIL‐53(Fe)/TiO₂) was prepared using a hydrothermal method. This material was then calcined at 500°C to obtain a MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ photocatalyst. A photocatalytic study of MIL‐53(Fe)/TiO₂ and MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ toward cationic methylene blue (MB) and anionic methyl orange (MO) showed that MIL‐53(Fe)/TiO₂ (0.25 wt%) and MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ (0.75 wt%) resulted the best degree of dye degradation. The MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ (0.75 wt%) composite for instance is capable of degrading almost 100% of 20‐ppm MB and MO, respectively, within 6 hr. Photocatalytic degradation of MB and MO was well fitted to the Langmuir‐Hinshelwood pseudo‐first order kinetics model, which indicates physisorption as the key partway that facilitates dye decomposition on the surface of a photocatalyst under UV‐A irradiation. This study provides new insights into the exploration of MILs/TiO₂ materials for the environmental remediation and pollution control.     

Incorporation of metal‐organic framework amino‐modified MIL‐101 into glycidyl methacrylate monoliths for nano LC separation

Metal‐organic frameworks consisting of amino‐modified MIL‐101(M: Cr, Al, and Fe) crystals have been synthesized and subsequently incorporated to glycidyl methacrylate monoliths to develop novel stationary phases for nano‐liquid chromatography. Two incorporation approaches of these materials in monoliths were explored. The metal‐organic framework materials were firstly attached to the pore surface through reaction of epoxy groups present in the parent glycidyl methacrylate‐based monolith. Alternatively, NH₂‐MIL‐101(M) were admixed in the polymerization mixture. Using short time UV‐initiated polymerization, monolithic beds with homogenously dispersed metal‐organic frameworks were obtained. The chromatographic performance of embedded UV‐initiated composites was demonstrated with separations of polycyclic aromatic hydrocarbons and non‐steroidal anti‐inflammatory drugs as test solutes. In particular, the incorporation of the NH₂‐MIL‐101(Al) into the organic polymer monoliths led to an increase in the retention of all the analytes compared to the parent monolith. The hybrid monolithic columns also exhibited satisfactory run‐to‐run and column‐to‐column reproducibility.