二元阴阳离子表面活性剂法合成介孔氧化硅囊泡

以十二烷基磺酸钠(SDS)和十六烷基三甲基溴化铵(CTAB)为表面活性剂, 在SDS与CTAB的摩尔比为1.0~2.3时, 以正硅酸乙酯(TEOS)为硅源, 在氨水-水体系中于68℃下合成介孔氧化硅囊泡. 通过透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 热重分析仪(TGA)和氮气吸附-脱附实验仪对合成的产物进行表征. 结果表明, 合成的产物为介孔氧化硅囊泡聚集体, 孔径约为4 nm, 样品的Brunauer-Emmett-Teller(BET)比表面积为826 m²/g. 对介孔氧化硅囊泡的形成机理做了初步探讨.     

有机/无机复合介孔膜的合成及其生物酶吸附行为研究

以正硅酸四乙酯(TEOS)为硅源、三嵌段共聚物(F127)为表面活性剂, 聚碳酸酯膜为硬模板, 并采用抽滤法在聚碳酸酯膜内的亚微米级孔道中组装介孔氧化硅从而制备出有机(聚碳酸酯)/无机(介孔氧化硅)复合介孔膜. 通过扫描电镜、能量分散光谱以及透射电镜等实验表征了该有机/无机复合介孔膜的组成、结构及形貌. 研究结果表明: 通过该方法可以在聚碳酸酯膜内孔道中形成长度为9 μm、直径为200 nm的一维氧化硅棒状材料, 且该棒状材料具有无序蠕虫状和有序体心立方的混合介孔结构, 有序体心立方介孔的平均孔径约为8.5 nm. 另外, 初步考察了该复合介孔膜对生物酶的物理吸附行为, 结果表明其对肌红蛋白酶的单位吸附负载量为5.85 mg/g.     

可用于色谱固定相的介孔氧化硅球材料的合成

采用非离子型嵌段高分子表面活性剂EO₂₀PO₃₀EO₂₀ (P65)为结构导向剂, 正硅酸乙酯为硅源, 在酸性介质中, 静置法制备了微米级介孔氧化硅球. 通过改变合成温度、反应时间或者无机盐KCl的加入量, 可以调节介孔氧化硅球的直径(9.0～17.6 μm); 加入1,3,5-三甲苯(TMB)或者调节水热温度, 可以调节介孔氧化硅球的孔径(2.3～4.8 nm). 采用X射线衍射(XRD)、N₂吸附-脱附、扫描电镜(SEM)、激光散射粒度分布和对溶菌酶的吸附等方法, 对介孔氧化硅球的结构、孔性质、形貌、吸附性质等进行了表征. 实验发现, 孔径较小的介孔氧化硅球(≤4.3 nm)对溶菌酶的吸附不明显(≤42 mg/g), 而孔径(4.8 nm)大于溶菌酶直径的材料对溶菌酶有较大的吸附量(192 mg/g), 说明孔径均匀可调的介孔氧化硅球材料可以很好地用作体积排阻色谱柱的固定相.     

香蒲基生物炭的活化及对VOCs吸附的应用

以香蒲为原料制备生物炭(Biochar), 并用不同试剂进行活化. 活化前的Biochar比表面积和孔体积很小, 分别为1.71 m²/g和0.00421 cm³/g, 而活化后的Biochar比表面积和孔容均增大, 其中经碳酸钠（Na₂CO₃）活化后的Biochar比表面积和孔容最大. 研究了Na₂CO₃与Biochar的质量比对其活化的影响, 确定了Na₂CO₃/Biochar最佳质量比为3∶1条件下, 得到的样品Biochar-Na₂CO₃-3具有最优的表面积和孔容, 分别为624 m²/g和0.211 cm³/g, 并具有优异的挥发性有机化合物(VOCs)吸附性能, 其正己烷、 甲苯和92号汽油的静态吸附容量分别为1.03, 0.814和0.751 g/g, 正己烷和甲苯的动态吸附容量分别为1.00和0.796 g/g, 且吸附稳定性相对较高, 优于商业用活性炭(AC)和硅胶(SG).     

杂原子介孔Ce-MCM-41分子筛的制备及其吸附脱除甲硫醚性能

以十六烷基三甲基溴化铵为模板剂,正硅酸乙酯(TEOS)为硅源,硝酸铈为铈源,采用水热法合成了杂原子介孔分子筛Ce-MCM-41。XRD和FT-IR表征结果表明,当加入的Ce/Si物质的量比小于0.04时合成了规整有序的介孔结构,并将Ce原子引入到MCM-41骨架中。N₂吸附-脱附测试获得MCM-41和Ce-MCM-41(Ce/Si物质的量比为0.04)的平均孔径分别为2.82和2.46 nm,孔容分别为0.762 1和 0.689 4 m³/g,BET比表面积分别为986.42和756.8 m²/g。NH₃-TPD表征结果表明,Ce-MCM-41的酸性要明显强于MCM-41,但两种分子筛的酸性均较弱。利用合成的MCM-41和Ce-MCM-41吸附脱除甲硫醚浓度为58 μg(甲硫醚)/g的甲硫醚/氮气混合气中的甲硫醚。甲硫醚分子尺寸的模拟结果为0.464 8 nm,可以很容易地进入分子筛的介孔孔道中。由于Ce-MCM-41分子筛具有较多的酸量,其硫吸附容量7.52 mg(S)/g明显高于MCM-41的4.57 mg(S)/g。MCM-41和Ce-MCM-41都具有较好的再生性能,再生3次后硫吸附容量仍可恢复到初始容量的80%,分别为3.52和 5.86 mg(S)/g。     

囊泡状二氧化硅的合成及油气吸附性能

以正硅酸四甲酯(TMOS)为硅源,P123(EO20PO70EO20)为表面活性剂,在p H=6的磷酸缓冲体系中制备了囊泡状二氧化硅材料.利用乙醇萃取脱除模板剂P123,电镜观测结果表明所得二氧化硅具有大孔囊泡结构,N2吸附结果表明其具有高比表面积和大孔容.通过Boehm滴定法确定了硅羟基数量与吸水率呈正相关.用囊泡状二氧化硅材料与商业化活性炭(AC)和硅胶(SG)对水蒸气、正己烷和油气进行静态吸附.在自建的动态正己烷吸附装置上用对囊泡状二氧化硅材料和商业化AC和SG对正己烷进行动态吸附.吸附结果表明,囊泡状二氧化硅材料的静/动态吸附容量和稳定性都远高于商业化活性炭和硅胶.     

毫米级轻质高强度多孔二氧化硅球的制备与表征

以F127和十六烷基三甲基溴化铵(CTAB)为模板,正硅酸乙酯(TEOS)为硅源,在液体石蜡/水(W/O)体系中通过自组装合成了毫米级轻质高强度多孔二氧化硅球.采用激光粒度分析仪、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、氮气吸附-脱附分析仪及纳米压痕仪对合成的产物进行了表征.结果表明,合成产物是直径为(1.40±0.20)mm的球形颗粒,球内存在大量多级孔洞,从2 nm到几十纳米的多级孔径并存,样品的Brunauer-Emmett-Teller(BET)比表面积为498.00 m2/g.另外,毫米级多孔二氧化硅球的表观密度为0.44 g/cm3,硬度与弹性模量分别为549.00 MPa和9.19 GPa.     

MCM-48分子筛的高效合成途径

以正硅酸乙酯(TEOS)为硅源,十六烷基三甲基溴化铵(CTAB)为模板剂,用水热合成法合成MCM-48,在合成过程中通过降低pH值等方法可以使得MCM-48的产率显著提高,当pH=7时,产率达到97%。XRD和物理吸附表明合成的介孔分子筛具有高比表面积(BET,～1000m^2/g)和规整的孔道结构且孔径集中在2.6nm左右。     

放射孔二氧化硅及其核壳结构的制备与表征

室温下以十六烷基三甲基溴化铵(CTAB)为模板剂, 正硅酸乙酯(TEOS)为硅源, 氨水(质量分数25%)为催化剂, 在水-乙醇-乙醚作共溶剂的体系中以氨基化的实心二氧化硅(NH₂-sSiO₂)为添加剂, 制备了放射孔二氧化硅及其核壳结构(sSiO₂@rSiO₂). 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、小角X射线衍射(XRD)、氮气吸附-脱附实验和孔径分布测定对其进行了表征和分析. 结果表明, 合成的产物为0.4~1 μm的球形粒子, 球上存在多级放射状孔道结构, 孔径从3 nm到几十纳米的多级孔径并存, 样品的Brunauer-Emmett-Teller(BET)比表面积为996 m²/g. 最后对放射孔二氧化硅的形成机理及核壳结构的影响因素进行了初步探讨.     

极稀溶液体系中自组装合成纳米介孔氧化硅及其铝修饰材料

在极稀溶液中, 通过改变反应溶剂去离子水的量或原料中铝源的量, 可控合成了不同粒径(20~70 nm)、形貌和孔道结构的纳米介孔氧化硅颗粒和纳米介孔铝掺杂氧化硅材料. 这种材料具有高比表面积(BET比表面积1000 m²/g)和较大的孔容(1.1~1.8 cm³/g). 反应物浓度降低或反应物中添加铝源后, 介孔材料的有序性下降, 粒径减小, 孔容增大, 并产生大量的间隙孔. 通过小角X射线衍射(SAXRD)、透射电镜和氮气吸附-脱附实验表征了样品.     

Silicalite-1 growth from clear solution: Effect of alcohol identity and content on growth kinetics

In situ small-angle X-ray scattering (SAXS) is used to investigate the influence of alcohol identity and content on silicalite-1 growth from clear solutions at 368 K. Several tetraalkyl orthosilicates (Si(OR)4, R = Me, Pr, and Bu) are used to synthesize silicalite-1 from clear solution mixtures comparable to those previously investigated (i.e. 1:0.36:20 TEOS:TPAOH:H2O (TEOS = tetraethyl orthosilicate; TPAOH = tetrapropylammonium hydroxide), 368 K). All TPAOH-organosiloxane mixtures studied form silica nanoparticles after aging at room temperature for 24 h. Full-profile fitting analysis of the SAXS data indicates the particles are ellipsoidal and is inconsistent with the presence of "nanoslabs" or "nanoblocks". Synthesis using TEOS as the silica source have an induction period of approximately 7.5 h and a growth rate of 1.90 +/- 0.10 nm/h at 368 K. Changing the silica source to tetramethyl orthosilicate (TMOS) does not change the induction period; however the particle growth rate is decreased to 1.65 +/- 0.09 nm/h at 368 K. Variable-temperature SAXS measurements for syntheses with TEOS and TMOS show the activation energy for silicalite-1 growth is 60.0 +/- 2.9 and 73.9 +/- 2.8 kJ/mol, respectively, indicating the alcohol identity does influence the growth rate. By mixing tetrapropyl orthosilicate (TPOS) with TEOS (1.6:1.0 molar ratio) as the silica source, the precursor solution shows a shorter induction period (6.0 h) and a faster particle growth rate (2.16 +/- 0.06 nm/h). The alcohol identity effect is more pronounced when other organocations (e.g. alkyltripropylammonium cations) are used to make silicalite-1 at 368 K. Removing ethanol from the precursor solution decreases the induction period to approximately 4.5 h and increases the particle growth rate to 2.99 +/- 0.13 nm/h. Mixtures with 2 equiv of ethanol have an induction period and particle growth rate of 6.0 h and 2.04 +/- 0.03 nm/h, respectively. The results demonstrate the alcohol identity and content influence silicalite-1 growth kinetics. One possible explanation is varying the alcohol identity and content changes the strength of the hydrophobic hydration of the structure-directing agent and the water-alcohol interaction, resulting in less efficient interchange between clathrated water molecules and solvated silicate species.     

原位限域生长策略制备有序介孔碳负载的超小MoO3纳米颗粒

采用原位限域生长策略制备了一系列有序介孔碳负载的超小MoO₃纳米颗粒复合物(OMC-US-MoO₃). 其中, 有序介孔碳被用作基质来原位限域MoO₃纳米晶的生长. 依此方法制备的MoO₃纳米晶具有超小的晶粒尺寸(<5 nm), 并在介孔碳骨架内具有良好的分散度. 制得的OMC-US-MoO₃复合物具有可调的比表面积(428~796 m²/g)、 孔容(0.27~0.62 cm³/g)、 MoO₃质量分数(4%~27%)和孔径(4.6~5.7 nm). 当MoO₃纳米晶的质量分数为7%时, 所得样品OMC-US-MoO₃-7具有最大的孔径、 最小的孔壁厚度和最规整的介观结构. 该样品作为催化剂时, 表现出优异的环辛烯选择性氧化性能.     

氨水诱导硅核自组装制备介孔SiO_2

在无模板剂的条件下,通过控制氨水用量,利用正硅酸乙酯水解制备了粒径约20 nm的SiO2初级粒子;随后用过量氨水诱导SiO2初级粒子交联生长,得到孔径在10~50 nm、孔容达2.05 cm3.g-1的介孔SiO2;考察了介孔SiO2的吸附性能.结果表明,所制备的介孔SiO2具有优良的吸附性能.     

一种可精确控制粒径的SiO2微球合成方法

用改进的种子法合成SiO2微球. 微球生长过程中连续缓慢添加正硅酸乙酯,使用动态光散射法实时监控微球粒径的增长过程,调节正硅酸乙酯的添加,实现对粒径的精确控制. 为制备禁带位置位于1000 nm 的光子晶体,合成粒径为446 nm的SiO2微球,微球粒径在4 h内从193 nm 增长到446 nm,远远快于传统种子法,微球粒径与目标粒径偏差为±5 nm. 制得的SiO2微球被组装为光子晶体,其禁带位置恰好位于1000 nm.     

Femtosecond dynamics of electron transfer in a neutral organic mixed-valence compound

In this article we report a femtosecond time-resolved transient absorption study of a neutral organic mixed-valence (MV) compound with the aim to gain insight into its charge-transfer dynamics upon optical excitation. The back-electron transfer was investigated in five different solvents, toluene, dibutyl ether, methyl-tert-butyl ether (MTBE), benzonitrile and n-hexane. In the pump step, the molecule was excited at 760 nm and 850 nm into the intervalence charge-transfer band. The resulting transients can be described by two time constant. We assign one time constant to the rearrangement of solvent molecules in the charge-transfer state and the second time constant to back-electron transfer to the electronic ground state. Back-electron transfer rates range from 1.5 × 10¹² s⁻¹ in benzonitrile through 8.3 × 10¹¹ s⁻¹ in MTBE, around 1.6 × 10¹¹ s⁻¹ in dibutylether and toluene and to 3.8 × 10⁹ s⁻¹ in n-hexane.     

Study on the morphological regulation mechanism of hollow silica microsphere prepared via emulsion droplet template

The morphology regulation of hollow silica microspheres is significant for their properties and applications. In this paper, hollow silica microspheres were formed through the hydrolysis and condensation reaction of tetraethyl orthosilicate (TEOS) at the interface of the emulsion droplet templates composed of liquid paraffin and TEOS, followed by dissolving paraffin with ethanol. The effects of various factors including the emulsifier structure and content, TEOS content, catalyst type, and the ethanol content in the continuous water phase on the particle size, shell thickness and morphology of the prepared hollow silica microspheres were studied in detail. The results show that the diffusion and contact of TEOS and water molecules as well as the hydrolysis condensation reaction of TEOS at the oil-water interface are two critical processes for the synthesis and morphological regulation of hollow silica microspheres. Cationic emulsifier with a hydrophobic chain of appropriate length is the prerequisite for the successful synthesis of hollow silica microspheres. The ethanol content in water phase is the dominant factor to determine the average diameter of hollow microspheres, which can vary from 96 nm to 660 nm with the increase of the volume ratio of alcohol-water from 0 to 0.7. The silica wall thickness varies with the content and the hydrophobic chain length of the emulsifier, TEOS content, and the activity of the catalyst. The component of the soft template will affect the morphology of the silica wall. When the liquid paraffin is replaced by cyclohexane, hollow microspheres with fibrous mesoporous silica wall are fabricated. This work not only enriches the basic theory of interfacial polymerization in the emulsion system, but also provides ideas and methods for expanding the morphology and application of hollow silica microspheres.     

反相微乳液法制备纳米SiO2的研究

在壬基酚聚氧乙烯5醚(NP-5)/环己烷/氨水的反相微乳液体系中，进行正硅酸乙酯(TEOS)的水解、缩合反应，得到粒径在30～50 nm的单分散纳米SiO₂胶体。红外光谱法(FTIR)及透射电子显微镜(TEM)观察证明了纳米SiO₂粒子的生成。反相微乳液体系相图的研究表明，水相为氨水比纯水有较窄的W/O型微乳区。氨水微乳液是碱催化TEOS水解、缩合制备纳米SiO₂粒子的适宜体系。当体系中TEOS的浓度增大时，粒子的粒径随之增大。降低NP-5     

多形貌中空介孔SiO2的可控合成及复合物对Cu2+的吸附还原

以间苯二酚/甲醛(RF)树脂为软模板, 正硅酸乙酯(TEOS)为硅源, 十六烷基三甲基溴化铵(CTAB)为制孔剂, 采用一锅溶胶-凝胶法制备了多形貌中空介孔二氧化硅微球(HMSM). 通过改变甲醛用量调控软模板RF树脂的结构, 可以获得一系列不同形貌及结构的HMSM, 随着甲醛用量的增加, HMSM结构表现为单层壳空心球、 蛋黄壳空心球、 双层壳空心球等结构. 其中具有蛋黄壳空心球结构的HMSM比表面积可达691 m ²/g, 孔体积达2.23 cm ³/g, 孔径均匀(3.5 nm). 以硝酸铈铵为引发剂, 在具有蛋黄壳空心球结构的HMSM中引发丙烯腈自由基聚合, 并将支链聚丙烯腈上的氰基偕胺肟化, 制得HMSM接枝聚偕胺肟(HMSM-g-PAO). 以100 mg/L的CuCl₂溶液为目标溶液, 在pH=4.0时测试合成的HMSM-g-PAO对Cu ²⁺的吸附效果, 发现吸附平衡时Cu ²⁺吸附量达134 mg/g.     

Synthesis of silica hollow spheres assisted by ultrasound

A simple and effective method for synthesizing silica hollow spheres is presented. The synthesis utilizes vesicles from oppositely charged surfactants sodium dodecyl sulfate (SDS) and tetrapropylammonium bromide (TPAB) aqueous solution as template for the silica growth. Tetraethyl orthosilicate (TEOS) is added to the vesicular template as a precursor for the silica formation. Ultrasound was employed to accelerate the formation of vesicles template. The morphology of the silica spheres is uniform and well-defined (diameter: 200 nm-5 microm, wall thickness: 50 nm). The product was also characterized by FTIR, TG-DTA, N2 adsorption. TEM images reveal that the spheres have structure stability after calcinations at 550 degrees C.