APPLICATION OF NONIONIC TEMPERATURE SENSITIVE HYDROGEL FOR CONCENTRATION OF PROTEIN AQUEOUS SOLUTION

Six different N-alkyl substituted acrylarnide nonionic hydrogels were prepared and their swelling characteristics were measured. Poly N-isopropyl acrylamide (PNIPA) and poly N-n-propyl-acrylamide (PNNPA) temperature sensitive hydrogels were chosen as the nonionic temperature sensitive hydrogels for concentration of very dilute aqueous protein solution. The separation properties of PNIPA and PNNPA hydr0gels with different network dimensions were studied and the modification of the hydrogels was surveyed in order to decrease their surface adsorption of protein molecules. The experimental results of the concentration of BSA (Bovin serum albumin) dilute aqueous solution by hydroxylpropyl methacrylate (HPMA) copolymerized PNIPA hydrogel were given. The value and the limitation of concentration of dilute aqueous protein solution by this method was evaluated.     

Effect of surface charge on adsorption of bovine serum albumin 2. Interaction of protein molecules with an anionic monolayer,as studied by ellipsometry,radiotracer and surface tension measurements

The adsorption of bovine serum albumin (BSA) onto an anionic monolayer of sodium docosylsulfate (SDocS) spread at the air/water interface was studied by ellipsometry. The adsorption behavior of BSA was estimated from the observed changes in phase differences and in the ratio of reflection coefficients. The dynamic process of BSA adsorption was measured after the injection of BSA solution into the aqueous substrate of SDocS monolayer. The gentle stirring of the substrate solution for 10 min was found to be enough to make the solution homogeneous without damaging the monolayer. The adsorption characteristics of BSA onto a negatively charged surface was compared with that onto a positively charged surface previously reported.The amount of adsorption depended on time and showed a maximum with an initial rapid rise, followed by gradual decrease toward the ultimate equilibrium value. The amount and time of the maximum adsorption depended on the concentration of BSA added to the aqueous substrate.Separate radiotracer measurement, using³⁵S-labeled SDocS monolayer, which is insoluble by itself, revealed that SDocS is solubilized into the bulk solution when BSA is added to the aqueous substrate.     

牛血清白蛋白在医用聚氨酯弹性体表面的吸附

制备了具有较好机械性能的异佛尔酮二异氰酸酯(IPDI)型聚氨酯弹性体胶片, 并进行表面肝素化处理, 得到抗凝血医用导管材料. 将聚氨酯胶片浸泡在牛血清白蛋白(BSA)水溶液中, 利用稀溶液黏度法研究了牛血清白蛋白在聚氨酯胶片表面的动态吸附情况, 并采用界面校正黏度方程计算溶液浓度变化. 研究发现, 牛血清白蛋白分子能迅速吸附到聚氨酯胶片表面, 但达到吸附平衡需要较长时间. 牛血清白蛋白在聚氨酯表面吸附后的溶液中分子构象发生变化.     

Competitive adsorption of collagen and bovine serum albumin—effect of the surface wettability

The competitive adsorption of collagen and bovine serum albumin (BSA) on surfaces with varied wettability was investigated with imaging ellipsometry, and ellipsometry. Silane modified silicon surfaces were used as substrates. The results showed that surface wettability had an important effect on protein competitive adsorption. With the decrease of surface wettability, the adsorption of collagen from the mixture solution of collagen and BSA decreased, while the adsorption of BSA increased.     

A new temperature-sensitive polymer: Poly(ethoxypropylacrylamide)

In this study, a new temperature sensitive polymer was obtained by the solution polymerization of ethoxypropylacrylamide. The monomer, N-(3-ethoxypropyl)-acrylamide was synthesized by the nucleophilic substitution reaction of 3-ethoxy-propylamine and acryloyl chloride. The solution polymerization was performed in ethanol at 70 °C, by using azobisizobutyronitrile as the initiator. Poly(N-(3-ethoxypropyl)acrylamide), PEPA, exhibited a reversible phase transition by the temperature. The effects of polymer and salt concentrations on the lower critical solution temperature, (LCST) behaviour were investigated. LCST was found to be strongly dependent on the polymer concentration. The dynamic light scattering (DLS) measurements confirmed the formation of aggregates by the association of nucleated polymer chains at the temperatures higher than LCST. However an unusual behaviour, a marked decrease in the hydrodynamic diameter by the increasing PEPA concentration was observed below the LCST. The effect of salt concentration on the critical flocculation temperature of PEPA was reasonably similar to poly(isopropylacrylamide), PNIPA. In the ethanol-water media, the reversible phase transition behaviour was observed up the ethanol concentration of 30% v/v. This study indicated that PEPA was a new alternative thermally reversible material for PNIPA. With respect to the well-defined temperature-sensitive polymers like PNIPA, polymer concentration dependent LCST of PEPA can provide significant advantages in the applications like drug targeting, affinity separation and immobilization of bioactive agents.     

BSA和SDBS在水溶液与空气界面的相互作用

表面活性剂与蛋白质在界面处的相互作用在许多应用里都会遇到．如去污、药品或生物制剂的制备和提纯、某些开科手术等等[1]这常常涉及到表面活性剂与蛋白质在界面的吸附，蛋白质大分子在界面吸附层的取向和构象．对于这两种物质在界面处可能发生的相互作用的性质，是表面活性剂     

羟基磷灰石与牛血清白蛋白相互作用的原位红外光谱研究

应用原位(in situ)全反射红外光谱研究牛血清白蛋白在电化学法制备的羟基磷灰石表面的吸附和成键行为, 探索电化学法制备的HA生物材料/生物环境界面过程和生物相容性的微观本质.     

基于光波导分光光谱技术研究蛋白质与亚甲基蓝的竞争吸附行为

通过利用时间分辨光波导分光光谱技术原位测量从蛋白质-亚甲基蓝(MB)混合水溶液吸附到亲水玻璃光波导表面的MB可见光吸收谱,观测到在溶液pH值低于蛋白质等电点时MB与牛血清蛋白(BSA)以及MB与血红蛋白(Hb)存在竞争吸附行为,进一步测得这种竞争吸附行为对蛋白质浓度十分敏感,可以用于简单测定溶液中的蛋白质含量.基于Langmuir等温吸附理论推导出了两种分子竞争吸附的动力学方程,并利用该动力学方程对实验测得的吸光度随时间变化曲线进行了最佳拟合,揭示了玻璃表面吸附的MB分子个数在达到最大值后随时间呈指数衰减,同时得出拟合参数与蛋白质浓度呈准线性关系.     

The effect of surface coverage on conformation changes of bovine serum albumin molecules at the air-solution interface detected by sum frequency generation vibrational spectroscopy

The air-BSA solution interface has been investigated by various techniques for years. From these studies we know that BSA molecules segregate at the BSA solution-air interface, and the surface coverage increases with the increase of the bulk solution concentration. However, questions still remain as to whether the protein changes conformation, orientation, or a combination of the two upon adsorption. In this paper, by using sum frequency generation (SFG) vibrational spectroscopy we found that the conformation of interfacial BSA molecules changes dramatically at the solution-air interface, compared to that of the native BSA in solution. The hydrophobic methyl groups of BSA molecules at this interface tend to align along the surface normal. The degree of such conformational changes of surface BSA molecules depend on the surface coverage, indicating that the protein-protein interaction plays a very important role in determining the conformation of interfacial protein molecules. At very low surface concentration, the adsorbed BSA molecules unfold substantially. Our results can provide a molecular interpretation of results obtained from other studies such as protein layer thickness and surface tension measurements of protein solution.     

Modes of conformational changes of proteins adsorbed on a planar hydrophobic polymer surface reflecting their adsorption behaviors

Infrared spectra of hen egg white lysozyme and bovine serum albumin (BSA) adsorbed on a solid poly tris(trimethylsiloxy)silylstyrene (pTSS) surface in D2O solution were measured using attenuated total reflection (ATR) Fourier transform infrared spectroscopy. From the area and shape of the amide I' band of each spectrum, the adsorption amount and the secondary structure were determined simultaneously, as a function of adsorption time. We could show that the average conformation for all the adsorbed lysozyme molecules was solely determined by the adsorption time, and independent of the bulk concentration, while the adsorption amount increased with the bulk concentration as well as the adsorption time. These results suggest that lysozyme molecules form discrete assemblies on the surface, and that the surface assemblies grow over several hours to have a definite architecture independent of the adsorption amount. As for BSA, the extent of the conformational change was solely determined by the adsorption amount, regardless of the bulk concentration and the adsorption time. These differences in the adsorption properties of lysozyme and BSA may reflect differences in their conformational stabilities.     

Properties of protein adsorption onto pore surface during microfiltration: Effects of solution environment and membrane hydrophobicity

Properties of bovine serum albumin (BSA) adsorption onto pore surface during the filtration of BSA containing solution with the Sirasu porous glass membrane with a pore size of 0.1 μm were studied. The effects of pH, ionic strength, and surface modification on the flux decline and breakthrough curves were observed. The adsorption properties of BSA were estimated quantitatively by using the internal fouling model, which relates the filtration performance to the adsorption interaction, the adsorption capacity, and the thickness of the adsorption layer. The electrostatic interaction between BSA and pore surface was estimated by the streaming potential measurement. The BSA adsorption involved a rapid adsorption in the early stage of filtration followed by a slow multilayer adsorption that dominates the long-term filtration performance. The electrostatic repulsive force reduced the overall adsorption interaction but the electrostatic attractive force did not affect the adsorption interaction. The effect of ionic strength on the BSA adsorption could be explained in terms of the shift of the IEP of BSA toward lower pH with the increase in ionic strength. The hydrophobicity of membrane did not affect the adsorption properties except for the adsorption interaction in the early stage of the filtration.     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶的合成及表征;N-异丙基丙烯酰胺;水凝胶;温敏性;快速响应     

Profiling protein-surface interactions of multicomponent suspensions via flow cytometry

This study presents the use of flow cytometry as a high-throughput quantifiable technique to study multicomponent adsorption interactions between proteins and surfaces. Flow cytometry offers the advantage of high-throughput analysis of multiple parameters on a very small sampling scale. This enables flow cytometry to distinguish between individual adsorbent particles and adsorbate components within a suspension. As a proof of concept study, the adsorption of three proteins--bovine serum albumin (BSA), bovine immunoglobulin gamma (IgG) and fibrinogen--onto five surface-modified organosilica microsphere surfaces was used as a model multicomponent system for analysis. By uniquely labeling each protein and solid support type with spectrally distinguishable fluorescent dyes, the adsorption process could be "multiplexed" allowing for simultaneous screening of multiple adsorbate (protein) and adsorbent (particle surface) interactions. Protein adsorption experiments quantified by flow cytometry were found to be comparable to single-component adsorption studies by solution depletion. Quantitative distribution of the simultaneous competitive adsorption of BSA and IgG indicated that, at concentrations below surface saturation, both proteins adsorbed onto the surface. However, at concentrations greater than surface saturation, BSA preferentially adsorbed. Multiplexed particle suspensions of optically encoded particles were modified to produce a positively and negatively charged surface, a grafted 3400 MW poly(ethylene glycol) layer, or a physisorbed BSA or IgG layer. It was observed that adsorption was rapid and irreversible on all of the surfaces, and preadsorbed protein layers were the most effective in preventing further protein adsorption.     

Macroporous Poly(N-isopropylacrylamide) hydrogels with adjustable size "cut-off" for the efficient and reversible immobilization of biomacromolecules

Poly(N-isopropylacrylamide) (PNIPA) hydrogels with varied degree of crosslinking (DC) were synthesized by using poly(ethylene glycol) (PEG) as an additive. A phase separated ("macroporous") morphology was formed when using PEG contents of > or = 20 wt.-%. Temperature-dependent degrees of swelling had been measured, and average mesh sizes of the swollen polymer network had been calculated. The loading of the hydrogels with labelled dextrans with various molar masses and bovine serum albumin (BSA)-via swelling of the shrunken gel in a cold solution-and their subsequent unloading-via immersion in hot water-were studied in detail. The loading efficiencies were close to zero for PNIPA prepared at PEG contents of < or = 10 wt.-%, and they increased sharply to about 100% for PNIPA prepared with PEG contents of > or = 20 wt.-%. A complete unloading was achieved as well. For macroporous PNIPA prepared at 40 wt.-% PEG content, the loading efficiency was a function of the DC, and the "cut-off" observed as a function of dextran or protein size correlated with the mesh size of the hydrogel. The function of these "smart" hydrogels can be explained by the temperature-induced "pumping" of the solution into the gel bulk via the permanent pores, along with an uptake into the adjacent hydrogel network. Those materials could be used as matrices for the efficient and reversible immobilization of (bio)macromolecules.     

Effect of electrostatic interaction on the adsorption of globular proteins on octacalcium phosphate crystal film

The electrostatic effect on the adsorption of globular proteins, such as bovine serum albumin (BSA), hen egg white lysozyme (LZM), and beta-lactoglobulin (beta-Lg), on octacalcium phosphate (OCP)-like crystal thin films was investigated. A poorly crystalline thin film was synthesized on a tissue culture polystyrene (TCP) surface and used as a model surface in this study. The solution pH clearly affected the electrostatic properties of both proteins and surface. The adsorbed amounts obtained at quasi-steady state were readily related to the solution pH for each protein. The adsorption rate is fast during the initial period and levels off gradually. The maximum adsorbed mass occurred at pH 7 for BSA and at pH 9 for LZM. beta-Lg adsorbed similar amounts at pHs lower than 9, but the adsorbed mass decreased at pHs higher than 9 where electrostatic repulsion exists. The pH values where the maximum adsorbed mass occurred may be considered as the conditions where electrostatic attraction is most favorable. The adsorbed mass of beta-Lg was the greatest among the proteins of interest while BSA adsorbed the least despite its greater molecular mass. LZM falls into the intermediate region. According to these observations, BSA has undergone conformational changes that prevent further adsorption to a greater extent than the others. A simple relationship between the adsorption rate and the electrostatic properties was not established. However, the order of magnitude of the adsorption rate at the initial period tends to be the same as that of maximum adsorbed mass for each protein.     

Responsive hybrid self-assemblies in aqueous media

Responsive copolymers have been prepared by grafting onto a poly(acrylamide-co-sodium acrylate) backbone [PAM-co-PANa] poly(N-isopropylacrylamide) stickers [PNIPA] characterized by a lower critical solution temperature (LCST) in water. From adsorption isotherms and DSC studies performed on PNIPA/silica mixtures, it was shown that PNIPA chains irreversibly interact with silica particles and that at low coverage they partially lose their responsiveness with temperature. When PNIPA is grafted onto a PAM-co-PANa backbone, which has no specific attraction to silica surfaces (only electrostatic repulsions), their binding process remains very similar to the one analyzed with PNIPA chains alone. Above critical copolymer and silica concentrations (Cp congruent with 1 g/L and CSi congruent with 30 g/L), hybrid networks can be formed following the rules of percolation theory. The viscoelastic properties of these networks are controlled by the concentration of inorganic cross links and the fraction of PNIPA grafts participating in bridges between particles, the others being involved in inelastic loops or pendant chains. For all of the mixtures investigated, an optimum weight ratio of RSi/PNIPA = 10-15 was found for the viscoelastic properties, in agreement with the saturation of silica beads by the copolymer. Because of the responsive behavior of PNIPA in aqueous solutions, graft copolymers are able to self-assemble with temperature, giving rise to a sol/gel transition upon heating. In the presence of added silica, hybrid aggregates (silica/PNIPA) coexist at high temperature with organic ones (PNIPA/PNIPA) with synergistic or antagonistic effects on the elastic properties depending on the proportion of PNIPA grafts per silica particle.     

Influence of pH of the BSA solutions on velocity of the rising bubbles and stability of the thin liquid films and foams

Influence of pH of the BSA solutions on velocity of the rising bubbles, stability of foams, and properties of single foam and wetting films was studied. It was found that the solution pH affected significantly the BSA surface activity and properties of the protein adsorption layer under dynamic and static conditions. At pH close to the isoelectric point (pH_IEP=4.8) the BSA showed the highest surface activity. The equilibrium microscopic foam films of thicknesses of 64–80 nm, depending on the BSA concentration, were obtained at pH=5.8. Under dynamic conditions the bubble rising velocity was reduced in a highest degree and the foam formed were most stable at the solutions pH-5.8 and 4.8. Lowering the bubble velocity shows that the BSA adsorption layer was formed, which retarded fluidity of the bubble surface. When the solution pH was significantly lower (pH=3.9) or much higher (pH=10) than the pH_IEP then the BSA practically had no influence on the bubble velocity and the foam stability was drastically reduced. Moreover, the pH variations affected also the time of the three-phase contact (TPC) formation on mica surface covered by the BSA adsorption layers. These pH dependent changes in the BSA surface activity indicate that the BSA linear conformers, existing at pH far away from the pH_IEP, have much higher affinity to aqueous phase resulting from higher net electrical charge present over the extended BSA molecule conformers.     

Synthesis of Temperature-Sensitive Poly(N-isopropylacrylamide) Hydrogel with Improved Surface Property

A new PNIPA hydrogel was synthesized by carrying out the polymerization in the gelated corn starch aqueous solution. This PNIPA hydrogel has an improved surface property and does not form the disadvantageous bubbles during the shrinking process. This change is due to the hydrogen bonds between the corn starch and the hydrophilic side groups of the PNIPA chains, which let the starch act as the long graft-like chains of the PNIPA hydrogel. During the reswelling process, this PNIPA hydrogel exhibits a sigmoidal swelling pattern. This hydrogel with improved surface property may be very useful for the potential applications of the temperature-sensitive hydrogel. Copyright 2000 Academic Press.     

牛血清白蛋白在超薄纳米二氧化钛膜表面的印迹与吸附

基于溶胶凝胶分子印迹方法,以溶胶二氧化钛TiO2为基质印迹了牛血清白蛋白分子。用1%的NaOH溶液可有效地除去纳米TiO2印迹膜中的模板分子。采用石英晶体微天平现场技术,研究了牛血清白蛋白在超薄纳米TiO2膜表面的吸附行为。研究表明,牛血清白蛋白在印迹膜和非印迹膜上的吸附量都随溶液浓度增加而增大,印迹膜具有吸附的特异性和可再生性,其吸附量是非印迹膜的3~5倍;在非印迹膜上的吸附符合Langmuir吸附模型,而在印迹膜上的吸附符合allosteric吸附模型;牛血清白蛋白在非印迹膜上的吸附量先随pH升高而增大,当pH为5左右时达到最大值,随后吸附量又随pH的增大而减小;而在印迹膜上其吸附量仅随pH增大而增大。     

Macroporous chitosan layer coated on non-porous silica gel as a support for metal chelate affinity chromatographic adsorbent

A new immobilized metal affinity chromatography (IMAC) matrix was prepared by coordinating Cu2+ with cross-linked chitosan coated on non-porous silica gel (Cu-CTS-SiO2). Macroporous structure could be formed on the coated layer by imprinting polyethylene glycol (PEG) in chitosan film. The surface morphology changes on Cu-CTS-SiO2 bead prepared in different condition were confirmed by scanning electron microscopy (SEM). Effects of chitosan and PEG content in coating solution, the molecular mass of PEG on the surface macropore formation and adsorption capacity of bovine serum albumin (BSA) were investigated. Results indicated that coating solution with 2% chitosan and 10% PEG 20000 was optimal. Batch experiments were also conducted for elucidating the optimal pH, the adsorption isotherm and adsorption kinetics of BSA. Adsorption isotherm of trypsin on the same adsorbent was also performed. Results showed that the support itself had low non-specific interaction with both BSA and trypsin. The maximum adsorption capacity for BSA and trypsin on the prepared IMAC adsorbent could reach 192 mg and 5000 IU, respectively calculated by every gram of chitosan. The binding and eluting condition for BSA were tested on column filled with the adsorbent. Crude BSA sample could be purified on the IMAC column.