不锈钢钝化膜耐蚀性与半导体特性的关联研究

通过极化曲线、交流阻抗谱和钝化膜半导体特性等电化学测量，研究了经电化学阳极氧化处理的不锈钢钝化膜在0.5 mol•L^-1 NaCl溶液中耐蚀性能与其半导体特性的关系，进一步探索电化学改性处理不锈钢钝化膜的耐蚀机理. 结果表明，不锈钢钝化膜在负于平带电位范围表现为p型半导体，在高于平带电位范围表现为n型半导体，这主要与组成钝化膜的Fe和Cr氧化物半导体性质有关. 与自然条件下形成的不锈钢钝化膜比较，发现经过电化学阳极氧化后不锈钢钝化膜具有较低的施主与受主浓度，平带电位负移，说明阴离子在钝化膜表面发生吸附. 低的施主与受主浓度及钝化膜表面负电荷的增强，可有效排斥侵蚀性Cl^－在钝化膜表面的特性吸附，有利于提高不锈钢的耐局部腐蚀性能.     

聚吡咯/聚苯胺复合型导电聚合物防腐蚀性能

采用循环伏安法,在含吡咯和苯胺的0.3 mol/L草酸水溶液中制备了聚吡咯/聚苯胺(PPy/Pani)的复合型导电聚合膜。采用红外光谱、极化曲线、自腐蚀电位-时间曲线、扫描电子显微镜和电化学阻抗谱研究了共聚膜的防腐蚀性能。结果表明,在1 mol/L H2SO4中,PPy、Pani与不锈钢基体发生氧化还原反应,促进不锈钢表面发生钝化;当苯胺与吡咯浓度比为1∶3时,制备得到的复合型导电聚合膜所保护的不锈钢自腐蚀电流最小,自腐蚀电位最高,保护时间最长。PPy、Pani及其共聚膜在3.5%NaCl溶液中电化学阻抗谱表明,所制备的PPy、Pani及其共聚物膜与不锈钢基体发生氧化还原反应,使其表面钝化;当Cl-到达不锈钢表面时,破坏钝化膜导致不锈钢腐蚀。     

非晶Fe40Ni40P14B6合金阳极钝化膜的电子能谱研究

应用表面分析技术XPS和AES（包括深度分布）分析了非晶Fe40Ni40P14B6合金在H3BO3－Na2B4O7（pH＝9．20）缓冲溶液中不同钝化势或不同钝化时间形成的阳极钝化膜的元素化学状态、结构和化学组成，探讨了加入Ⅲ、Ⅴ族B、P对非晶FeNi基合金钝化成膜的影响，并给出了阳极钝性成膜的一种机制．     

探究铁和铝在浓硫酸和浓硝酸中的电化学行为

铁和铝在冷的浓硫酸和浓硝酸中都因被钝化而阻止其进一步被腐蚀,通过用Fe、Al做原电池的电极材料,考察其在浓硫酸、浓硝酸中的钝化情况：Fe、Al的钝化快慢、钝化后金属表面氧化膜的致密程度、酸液温度等对钝化的影响等均有所不同。     

690合金在300 ℃含硫模拟碱性水化学中的腐蚀行为

690 合金作为压水堆核电站蒸汽发生器传热管的一种关键材料, 其在碱性环境下还原态硫导致的钝化膜的腐蚀退化是引发应力腐蚀开裂的关键原因之一. 本文采用动电位极化曲线, 结合扫描电镜(SEM)、俄歇能谱(AES)、二次离子飞行时间质谱(ToF-SIMS)研究了690合金在300 ℃模拟碱性水化学中的腐蚀行为, 并分析了硫代硫酸根与硫酸根对钝化膜特性的影响. 实验结果表明: 300 ℃碱性溶液中690合金表面钝化膜为外层的多孔层与内层的紧密层组成的双层结构, 所加入的硫酸盐种类对690合金的耐蚀性有较大影响; 硫代硫酸根使690合金钝化电流密度增加, 过钝化电位降低, 即钝化膜的耐蚀性降低; 此外, 硫代硫酸根使钝化膜中的Cr含量降低而Ni 含量提高, 硫代硫酸根会在合金表面电化学还原成为更低价态的硫进入钝化膜, 使钝化膜中的硫化物增多也是导致钝化膜防护性能变差的原因; 而硫酸根与钝化膜的作用较弱, 对钝化膜的影响较小.     

模拟混凝土孔溶液中钢筋钝化膜的光电化学方法研究

利用光电化学方法研究了钢筋在模拟混凝土孔溶液中钝化膜的电子性质，结果表明，钢筋在该溶液中形成的钝化膜是一种无定形的ｎ－型半导体成相膜，膜由多种铁氧化物组成，其组成受溶液中的离子、ＰＨ值、成膜电位影响，腐蚀抑制ＮａＮＯ２影响钝化膜的组成和生长过程，从而提高钢筋的抗氯离子点蚀能力。     

含镓、锡的铝合金在碱性溶液中的阳极行为

铝的电极电位负,为一1．66V（VS．SHE）,电化当量高（298Ah／g）是一种理想的阳板材料．但是由于铝在空气和水中表面形成一层致密的氧化膜,使其在中性溶液中处于钝化状态．而在酸性或碱性溶液中铝表面氧化膜就会被溶解破坏,与水直接反应,腐蚀中途难以中止．这一直是影响铝作为阳板材料应用和深入研究的障碍,特别是对铝阳极活化溶解机理的研究进展缓慢．虽然目前人们在铝中添加Ga、In、11、Zn、Sn、Mg、Hg等元素,研制出各种铝合金阳极,提高了铝阳极活化性能,但是这些研究本质上仍属于经验性的．到1983年Despic等人提出了“场…     

铝阳极氧化膜在中性NaCl溶液中的亚稳态点蚀研究

使用动电位极化法,电化学噪声和扫描电镜技术研究了工业纯铝L2经不同电流密度阳极氧化和不同方法封闭后于1mol/LNaCl中性溶液中的腐蚀行为.结果表明,阳极氧化能大大提高L2的耐蚀性,但当氧化膜较薄或氧化膜经长时间在溶液中浸泡后,试样表面仍能发生亚稳态点蚀,并在极化曲线上出现电流振荡和电位振荡.扫描电镜观察则表明,这些亚稳态点蚀孔径一般小于10μm,主要产生在膜中的金属间化合物周围.若氧化膜厚度增加或使用沸水和重铬酸盐封闭,均可有效地抑制亚稳态点蚀的发生.     

非晶态Fe—W合金镀层的表面改性

将Ｆｅ－Ｗ非晶态镀层在铬酸盐钝化液中进行化学钝化与电化学钝化，使之形成含多种钝化膜。阳极极化曲线说明，反镀层的孔蚀电位向正向移动了１．６８Ｆ；Ｆｅ－Ｗ非晶镀层在氯化钠溶液中浸泡近１ｈ表面发生严重腐蚀，而经钝化处理的镀层浸泡１个月，表面无变化，仍具有金属光泽。     

碳钢在N-甲基二乙醇胺介质中的电化学阻抗谱研究

应用电化学阻抗谱(EIS)研究碳钢在N-甲基二乙醇胺(MDEA)介质中的腐蚀行为.实验表明,未经预阴极活化处理的碳钢表面存在氧化膜,溶解氧促使它腐蚀速率增大,经活化处理去除氧化膜后则相反.在不含热稳定性盐(HSS)的MDEA溶液中,碳钢的腐蚀性随MDEA浓度的增加呈先上升后下降趋势;而在HSS高含量的溶液中,其腐蚀性则随MDEA浓度的增加而单调下降.在含有HSS模拟溶液中,碳钢的阳极极化EIS随极化电位由低到高分别出现感抗、负阻抗以及Warburg阻抗响应等特征,对应于孔蚀、活化状态向钝化状态过渡以及进入钝化的趋势,腐蚀反应的阴极过程表现为电化学反应和扩散传质混合控制,阳极过程为电化学反应控制.     

非晶Fe40Ni40P14B6合金阳极钝化膜的电子能谱研究

应用表面分析技术ＸＰＳ和ＡＥＳ（包括深度分布）分析了非晶Ｆｅ４０Ｎｉ４０Ｐ１４Ｂ６合金在Ｈ３ＢＯ３－Ｎａ２Ｂ４Ｏ７（ＰＨ＝９．２０）缓冲溶液中不同钝化时间形成的阳极钝化膜的元素化学状态、结构和化学组成，探讨了加入Ⅲ、Ｖ族Ｂ、Ｐ对非晶ＦｅＮｉ基合金钝化金钝化成膜的影响，并给出了阳极钝性成膜的一种机制。     

Thousand fold concentration of an alkaloid in capillary zone electrophoresis by micelle to solvent stacking

In this paper, the co-solvent of methanol-water was used to facilitate the sodium dodecyl sulfate (SDS) micelles collapse, thereby inducing the on-line sample focusing technique of micelle to solvent stacking (MSS). To demonstrate this stacking method, the mechanism of micelles collapse in co-solvent was discussed. The details of the required conditions were investigated and the optimized conditions were: running buffer, 20mM H(3)BO(3) and 20mM NaH(2)PO(4) solution (pH 4.0); micellar sample matrix, 20mM SDS, 20mM H(3)BO(3) and 20mM NaH(2)PO(4) solution (pH 4.0); co-solvent buffer, 20mM H(3)BO(3) and 20mM NaH(2)PO(4) in methanol/water (90:10, v/v). The validity of the developed method was tested using cationic alkaloid compounds (ephedrine and berberine) as model analytes. Under the optimized conditions, this proposed method afforded limits of detection (LODs) of 0.5 and 1.1ng/mL with 300 and 1036-fold improvements in sensitivity for ephedrine and berberine, respectively, within 15min.     

Reactivity of M(II) metal-substituted derivatives of pig purple acid phosphatase (uteroferrin) with phosphate

The Fe(II) of the binuclear Fe(II)Fe(III) active site of pig purple acid phosphatase (uteroferrin) has been replaced in turn by five M(II) ions (Mn(II), Co(II), Ni(II), Cu(II), and Zn(II)). An uptake of 1 equiv of M(II) is observed in all cases except that of Cu(II), when a second more loosely bound Cu(II) is removed by treatment with edta. The products have been characterized by different analytical procedures and by UV-vis spectrophotometry. At 25 degrees C, I = 0.100 M (NaCl), the nonenzymatic reactions with H(2)PO(4)(-) give the mu-phosphato product, and formation constants K/M(-1) show an 8-fold spread at pH 4.9 of 740 (Mn), 165 (Fe), 190 (Co), 90 (Ni), 800 (Cu), 380 (Zn). The variations in K correlate well with stability constants for the complexing of H(2)PO(4)(-) and (CH(3)O)HPO(3)(-) with M(II) hexaaqua ions. At pH 4.9 with [H(2)PO(4)(-)] > or = 3.5 mM rate constants k(obs) decrease, and an inhibition process in which a second [H(2)PO(4)(-)] coordinates to the dinuclear center is proposed. The mechanism considered accounts for most but not all of the features displayed. Thus K(1) values for the coordination of phosphate to M(II) are in the range10-60 M(-1), whereas K(2) values for the bridging of the phosphate to Fe(III) are in the narrower range 7.8-12.4. From the fits described K(i) approximately 10(3) M(-1) for the inhibition step, which is independent of the identity of M(II). Values of k(obs) decrease with increasing pH, giving pK(a) values which are close to 3.8 and independent of M(II) (Fe(II), Zn(II), Mn(II)). The acid dissociation process is assigned to Fe(III)-OH(2) to Fe(III)-OH(-), where OH(-) is less readily displaced by phosphate.     

UV laser ablation of GdCa4O(BO3)3 (GdCOB) investigated by Fourier transform ion cyclotron resonance mass spectrometry

The ions generated by laser ablation (LA) of calcium and gadolinium oxoborate GdCa4O(BO3)3 (GdCOB) were investigated by Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS), a powerful tool for the characterization of ionic species produced by laser interaction with solid material. In order to better understand the matter transfer and the mechanism of thin film growth by pulsed-laser deposition (PLD), cationic and anionic clusters generated by UV laser ablation of GdCOB bulk material were studied. Laser ablation of GdCOB leads to the formation of various cluster ions which result from association of CaO, BO and B2O3 building blocks (BB) with different charge carriers (CC): H+, BO+, GdO+ in positive ion mode, and BO2-, OK-, OH-, Cl-, WO3- in negative ion mode. LA-FTICRMS investigations allow us to assign a valence state to each metallic atom included in each BB. A +II chemical state may be associated with calcium and +II and +III ones to boron. UV laser ablation of GdCOB therefore induces reduction processes of boron species in the gas phase. The oxygen reactive atmosphere used during PLD experiments allows the growth of stoichiometric thin films by fixation of oxygen on the ablated species.     

A spectrofluorimetric method for cysteine and glutathione using the fluorescence system of Zn(II)-8-hydroxyquinoline-5-sulphonic acid complex.

The addition of thiol compounds to the fluorescence system of Zn(II)-8-hydroxyquinoline-5-sulphonic acid complex (Zn(II)-HQS) in H3BO3-Na2B4O7 buffer (pH 8.50) solution led to immediate fluorescence inhibition, which was proportional to their amounts. Based on this finding, a novel spectrofluorimetric method for the determination of cysteine (Cys) and reduced glutathione (GSH) has been developed. The detection limits were 17 ng ml(-1) and 0.6 microg ml(-1), respectively. Most amino acids had no interference at high concentrations. The proposed method has been applied to the determination of Cys in protein hydrolysate and cystine electrolyte, and GSH in human blood serum with recoveries of 95.6-104.5%.     

Synthesis and structural characterization of 0D vanadium borophosphate [Co(en)(3)](2)[V(3)P(3)BO(19)][H(2)PO(4)].4H(2)O and 1D vanadium oxides [Co(en)(3)][V(3)O(9)].H(2)O and [Co(dien)(2)][V(3)O(9)].H(2)O templated by cobalt complexes: cooperative organization of the complexes and the inorganic networks

A 0D vanadium borophosphate [Co(en)(3)](2)[V(3)P(3)BO(19)][H(2)PO(4)].4H(2)O (1) and two 1D vanadium oxides [Co(en)(3)][V(3)O(9)].H(2)O (2) and [Co(dien)(2)][V(3)O(9)].H(2)O (3) have been synthesized hydrothermally from the reaction mixture of V(2)O(5)-H(3)PO(4)-H(3)BO(3)-CoCl(2)-R-H(2)O at 110 degrees C (R: en or dien). The complex cations Co(en)(3)(3+) and Co(dien)(2)(3+) are cooperatively organized in the reaction medium to play a structure-directing role in the formation of the inorganic clusters and chains. The structures are determined by single-crystal X-ray diffraction analysis and further characterized by X-ray powder diffraction, ICP, and TG analyses. The structure of 1 contains isolated [V(3)P(3)BO(19)](5)(-) cluster anions, H(2)PO(4)(-) anions, racemic Co(en)(3)(3+) cations, and H(2)O molecules, which form a complex H-bond network. 2 and 3 both contain chains of corner-sharing VO(4) tetrahedra running along the 2(1) screw axis. The complex cations located in the interchain region interact with the chains through H-bonds. 2 is crystallized in an enantiomorphic space group and only one enantiomer of Co(en)(3)(3+) is involved in the structure. Crystal data: 1, monoclinic, C2/c, a = 32.8492(14) A, b = 11.9601(3) A, c = 22.6001(7) A, beta = 108.9630(8) degrees, Z = 8; 2, orthorhombic, P2(1)2(1)2(1), a = 8.1587(16) A, b = 12.675(3) A, c = 18.046(4) A, Z = 4; 3, monoclinic, P2(1)/c, a = 16.1663(10) A, b = 8.7028(3) A, c = 13.9773(5) A, beta = 103.1340(18) degrees, Z = 4.     

Electrochemical synthesis of Zn-Al layered double hydroxide (LDH) films

A new electrodeposition condition to produce Zn-Al LDH films was developed using nitrate solutions containing Zn (2+) and Al (3+) ions. Deposition was achieved by reducing nitrate ions to generate hydroxide ions on the working electrode. This elevates the local pH on the working electrode, resulting in precipitation of Zn-Al LDH films. The effect of deposition potential, pH of the plating solution, and the Zn (2+) to Al (3+) ratio in the plating solution on the purity and crystallinity of the LDH films deposited was systematically studied using X-ray diffraction and energy dispersive spectroscopy (EDS). The optimum deposition potential to deposit pure and well-ordered Zn-Al LDH films was E = -1.65V versus a Ag/AgCl in 4 M KCl reference electrode at room temperature using a solution containing 12.5 mM Zn(NO 3) 2.6H 2O and 7.5 mM Al(NO 3) 3.9H 2O with pH adjusted to 3.8. The resulting film contained 39 atomic %Al (3+) ions replacing Zn (2+) ions, leading to a composition of Zn 0.61Al 0.39(OH) 2(NO 3) 0.39. xH 2O. Increasing or decreasing the aluminum concentration in the plating solution resulted in the formation of aluminum- or zinc-containing impurities, respectively, instead of varying aluminum content incorporated into the LDH phase. Choosing an optimum deposition potential was important to obtain LDH as a pure phase in the film. When the potential more negative than the optimum potential is used, zinc metal or zinc hydroxide was deposited as a side product, whereas making the potential less negative than the optimum potential resulted in the formation of zinc oxide as the major phase. The pH condition of the plating solution was also critical, as increasing pH destabilizes the formation of the LDH phase while decreasing pH promoted deposition of other impurities.     

Corrosion resistances of passive films on low‐Cr steel and carbon steel in simulated concrete pore solution

The passive ranges of carbon steel rebar and 3Cr steel rebar in saturated Ca(OH)₂‐simulated concrete pore solution with pH 12.6 were determined by means of cyclic voltammetry and potentiodynamic polarization curves. Chronopotentiometry was used to obtain steady‐state conditions for the formation of passive films on rebar samples at different anodic potentials. Electrochemical impedance spectroscopy, Mott–Schottky and X‐ray photoelectron spectrometer curves were employed to compare the formed passive films at different potentials. Additionally, cyclic polarization curves were used to compare the corrosion resistances of formed passive films on the two rebars in saturated Ca(OH)₂‐simulated concrete pore solution with different concentration of Cl^?. The results show that the passive ranges of the two rebars are all between ?0.15 and +0.6 V, and more stable passive films can be formed on both rebars at the anodic potential of +0.3 V. In the absence of Cl^?, the stability and corrosion resistance of the passive film formed on the 3Cr rebar are better than those of CS rebar. The passive film of 3Cr steel has the relatively better pitting corrosion resistance than carbon steel in saturated Ca(OH)₂‐simulated concrete pore solution that contains different concentration of Cl^?. Copyright © 2016 John Wiley & Sons, Ltd.     

Modelling the formation and growth of anodic passive films on metals in concentrated acid solutions

Two model approaches to the formation of passive films as adsorbed layers during the active anodic dissolution of a metal in acid and their subsequent growth are presented. The first depicts passivation as proceeding in parallel to active dissolution. Adsorption of water on active surface sites leads to passivation, whereas adsorption of acid leads to active dissolution of the metal. The model is consistent with the impedance response during passivation of Fe and an Fe-20%Mo alloy in concentrated H₃PO₄. The second model is an updated version of the so-called surface charge approach to the mechanism of conduction of anodic passive films. It is based on the assumptions that oxygen vacancies are the main ionic charge carriers and the field strength in the barrier layer is constant. A negative surface charge built up at the film/solution interface via accumulation of metal vacancies accelerates oxygen vacancy transport, thus explaining the pseudoinductive behaviour of the metal/film/electrolyte system under small amplitude a.c. perturbation. The model describes the growth of thin anodic films on Fe, Mo and an Fe-20%Mo alloy in concentrated H₃PO₄. Received: 24 January 1997 / Accepted: 18 April 1997