On-column derivatization-capillary electrochromatography with o-phthalaldehyde/alkylthiol for assay of biogenic amines

The elution behaviors of the biogenic amines, histamine (HA) and its metabolite methyl histamine (MHA), were evaluated by means of on-column derivatization (OCD)-capillary electrochromatography (CEC) which employed a monolithic octadecylsilica (ODS) capillary column (20 cm of effective length x 50 microm of inner diameter). Five kinds of alkylthiols, e.g., 2- hydroxyethylthiol (or 2-mercaptoethanol (2-ME)), ethanethiol (ET), 1-propanethiol (1-PT), 2-methyl-1-propanethiol (2-MPT) and 1-butanethiol (1-BT) were separately presented at 5 mM each in the OCD-CEC separation run buffer consisting of 60% acetonitrile in 5 mM o-phthalaldehyde (OPA)-10 mM borate buffer (pH 10). When 2-ME was present in the run buffer solution, both derivatives corresponding to HA and MHA migrated separately, but closely together through the capillary column. Replacement of 2-ME with 1-BT in the run buffer solution caused a delay in their elution profiles on the electrochromatogram and the separation between those two peaks became remarkably improved. The elution times of HA and MHA followed the increase in alkyl chain length or hydrophobicity of thiol, 1-BT > 2-MPT > 1-PT > ET > 2-ME. Performance of on-line preconcentrations of HA and MHA was also evaluated by varying the electrokinetic injection voltage from 1 kV to 8 kV. The peak area counts corresponding to HA recorded about 50 times higher when 2 kV was applied for 240 s to a 0.1 mM HA solution than when 8 kV was applied for 5 s. This method was next applied to a sample of human urine spiked with HA and MHA at levels of 0.1 microM each. Although HA and MHA peaks were not identifiable among the peaks corresponding to the materials in the urine matrix when OPA/2-ME was employed in a run buffer for the OCD-CEC, the separation and identification of their peaks became possible by replacing 2-ME with 1-BT in the run buffer solution.     

Microemulsion electrokinetic chromatography versus capillary electrochromatography-UV-mass spectrometry for the analysis of flunitrazepam and its major metabolites

Benzodiazepines, namely flunitrazepam and its three major metabolites, were successfully separated by microemulsion electrokinetic chromatography. Separation was achieved using an untreated fused-silica capillary (48 cm (effective length 40 cm) x 50 num) at 25 kV; detection was performed by UV at 220 nm. The microemulsion system consisted of 70 mM octane, 800 mM 1-butanol, 80 mM sodium dodecyl sulfate (SDS) and 10 mM borate buffer, pH 9. Very high efficiencies (up to 400 000 plates) and resolution better than 3 were achieved. Since this technique is not compatible with mass spectrometry (MS) detection, a capillary electrochromatographic (CEC) method was developed to separate flunitrazepam and its metabolites. The effects of mobile phase composition and pH as well as voltage and temperature were systematically investigated. The optimized CEC method allowed the baseline separation of the investigated compounds. For the on-line coupling of CEC with electrospray ionization-mass spectrometry, the column was connected to a void fused-silica capillary using a Teflon connection. This configuration was found efficient and suitable for hyphenation of commercial CEC and MS instrumentation using commercially available CEC columns.     

Performance of throughout in-capillary derivatization capillary electrophoresis employing an on-line sample and run buffer loading device

We report on the effect on performance of varying the length of the capillary during throughout in-capillary derivatization (TICD) capillary electrophoresis (CE). Performance was evaluated by on-line coupling with a sample and CE runbuffer loading device that was newly introduced for this study. The device was assembled with a low cost using two 5 mm inner diameter (ID) disposable polyethylene syringes. First, a sequence was manually formed consisting of a 200 microL run buffer solution plug, a 100 microL sample plug and another 200 microL run buffer solution plug. Each plug was separated from its neighbor by a 100 microL air plug. When each plug reached the injection point where both a platinum-wire anode and the end of the separation capillary tube were located, 340 V/cm separation voltage (electrophoresis voltage) and 34 V/cm injection voltage were applied to the capillary for 3 s. Then the analytes were derivatized during migration in 50 microm ID capillaries filled with 2 mM o-phthalaldehyde (OPA)/N-acetylcysteine (NAC) in a 20 mM phosphate-borate buffer (pH 10), followed by separating and detecting of OPA derivatives by absorbance of 340 nm. Derivatization, separation, and detection were performed systematically using capillaries which varied in length from 5 to 80 cm. In the case of TICD-CE of a mixture containing 1 mM aspartic acid (Asp) and 20 mM m-nitorophenol (MNP) as a test solution, it was determined that peak area and peak width ratios of Asp to MNP did not depend on capillary length. Enantiomeric separations of DL-alanine (Ala) and Asp were examined using a run buffer consisting of a 45 microM beta-cyclodextrin (CD)-2 mM OPA/NAC-20 mM phosphate-borate buffer (pH 10). Even though the resolution of these enantiomeric pairs decreased with decreasing capillary length, as expected, the peaks corresponding to both enantiomeric amino acids were identified even when a 5 cm capillary was used. An 8-component amino acid mixture was also tested with 5 cm and 10 cm capillaries.     

Multi-walled carbon nanotube composites with polyacrylate prepared for open-tubular capillary electrochromatography

A new phase containing immobilized carbon nanotubes (CNTs) was synthesized by in situ polymerization of acid-treated multi-walled CNTs using butylmethacrylate (BMA) as the monomer and ethylene dimethacrylate as the crosslinker on a silanized capillary, forming a porous-layered open-tubular column for CEC. Incorporation of CNT nanomaterials into a polymer matrix could increase the phase ratio and take advantage of the easy preparation of an OT-CEC column. The completed BMA-CNT column was characterized by SEM, ATR-IR, and EOF measurements, varying the pH and the added volume organic modifier. In the multi-walled CNTs structure, carboxylate groups were the major ionizable ligands on the phase surface exerting the EOF having electroosmotic mobility, 4.0 × 10(4) cm2 V(-1)1 S(-1)1, in the phosphate buffer at pH 2.8 and RSD values (n=5), 3.2, 4.1, and 4.3%, for three replicate capillaries at pH 7.6. Application of the BMA-CNT column in CEC separations of various samples, including nucleobases, nucleosides, flavonoids, and phenolic acids, proved satisfactory upon optimization of the running buffers. Their optima were found in the borate buffers at pH 9.0/50 mM, pH 9.5/10 mM/50% v/v ACN, and pH 9.5/30 mM/10% v/v methanol, respectively. The separations could also be used to assess the relative contributions of electrophoresis and chromatography to the CEC mechanism by calculating the corresponding velocity and retention factors. Discussions about interactions between the probe solutes and the bonded phase included the π-π interactions, electrostatic repulsion, and hydrogen bonding. Furthermore, a reversed-phase mode was discovered to be involved in the chromatographic retention.     

A macrocyclic polyamine as an anion receptor in the capillary electrochromatographic separation of carbohydrates

An analytical approach of the 32-membered macrocyclic polyamine, 1,5,9,13,17,21,25,29-octaazacyclodotriacontane ([32]ane-N8) was described for the capillary electrochromatographic (CEC) separation of derivatized mono- and disaccharides. The column displayed reversal electroosmotic flow (EOF) at pH below 7.0, while a cathodic EOF was shown at pH above 7.0. The reductive amination of saccharides was carried out with p-aminobenzoic acid. Some parameters that affect the CEC separations were investigated. Several competitive ligands, such as Tris, EDTA and phosphate were also examined for the effect on the performance. We achieved a complete separation of all compounds as well as the excess derivatizing agent by using borate buffer (pH 9.0) in a mode of concentration gradient (60 mM inlet side and 70 mM outlet side). The relative standard deviation of the retention time measured for each sample was less than 4% in six continuous runs, suggesting that the bonded phase along with the gradient formed inside the column was quite stable. With the mixing modes of anion coordination, anion exchange, and shape discrimination, the interaction adequately accomplishes the separation of carbohydrates which are epimers or have different glycosidic linkage, although the electrophoretic migration is also involved in the separation mechanism.     

Titanium dioxide nanoparticles-coated column for capillary electrochromatographic separation of oligopeptides

A novel column made through the condensation reaction of TiO2 nanoparticles (TiO2 NPs) with silanol groups of the fused-silica capillary is described. EOF measurements under various buffer constitutions were used to monitor the completion of reactions. The results indicated that the EOF was dependent on the interactions between buffers and the bonded TiO2 NPs. With formate/Tris buffer, EOF reversal at pH below 5 and cathodic EOF at pH above 5 were indicated. The pI of the bonded TiO2 NPs was found at approximately ph 5. Only cathodic EOF was illustrated by substituting the mobile phase with either glutamate or phosphate buffer. It was elucidated that both glutamate and phosphate buffer yield a negative charge layer on the surface of TiO2 NPs attributable to the formation of a titanium complex. The CEC performance of the column was tested with angiotensin-type oligopeptides. Some parameters that would affect the retention behavior were investigated. The interactions between the bonded phases and the analytes were explicated by epitomized acid-base functional groups of the oligopepetides and the speciation of the surface oxide in different pH ranges. The average separation efficiencies of 3.1 x 10(4) plates/m is readily achieved with a column of 70 cm (50 cm) x 50 mum ID under an applied voltage of 15 kV, phosphate buffer (pH 6.0, 40 mM), and UV detection at 214 nm.     

Post-column derivatization capillary electrochromatography for detection of biogenic amines in tuna-meat

A system to perform post-column derivatization capillary electrochromatography (CEC) was developed for the first time. The system mainly included a 4-microm (O.D.) silica packed column (200 mm effective length x 0.1 mm inner diameter I.D.) with micro-magnetic particles (MMPs) frits, a T-junction connector, an in-line fluorescence detector and a high-voltage power supply. The system was evaluated by using histamine (HA) as a standard biogenic amine for this study. A 5 microM HA solution was loaded at the anodic site of the capillary column by applying 3 kV for 5s. Then, HA was electrophoretically eluted with a 20mM phosphate buffer (pH 7) by applying 3 kV, and was derivatized with 3mM o-phthalaldehyde (OPA)/N-acetylcysteine (NAC) in 100 mM borate (pH 10), which was continuously delivered through the reagent-loading capillary tube by gravity into the T-junction connector. HA derivative was finally detected with the in-line fluorescence detector (lambda(Ex)=340 nm, lambda(Em)=450 nm) at 9.7 min after sample loading. To test the utility of this system, it was next employed for its ability to detect the presence of HA and other kinds of biogenic amines, including cadaverine (Cad), spermidine (Spm) and tyramine (Tyr) in tuna-meat, once the validity of the method had been confirmed.     

Capillary electrochromatography with zwitterionic stationary phase on the lysine-bonded poly(glycidyl methacrylate-co-ethylene dimethacrylate) monolithic capillary column

A polymer-based neutral monolithic capillary column was prepared by radical polymerization of glycidyl methacrylate and ethylene dimethacrylate in a 100 mum id fused-silica capillary, and the prepared monolithic column was subsequently modified based on a ring opening reaction of epoxide groups with 1 M lysine in solution (pH 8.0) at 75 degrees C for 10 h to produce a lysine chemically bonded stationary phases in capillary column. The ring opening reaction conditions were optimized so that the column could generate substantial EOF. Due to the zwitterionic functional groups of the lysine covalently bonded on the polymer monolithic rod, the prepared column can generate cathodic and anodic EOF by varying the pH values of running buffer during CEC separation. EOF reached the maximum of -2.0 x 10(-8) m2v(-1)s(-1) and 2.6 x 10(-8) m2v(-1)s(-1) with pH of the running buffer of 2.25 and 10, respectively. As a consequence, neutral compounds, ionic solutes such as phenols, aromatic acids, anilines, and basic pharmaceuticals were all successfully separated on the column by CEC. Hydrophobic interaction is responsible for separation of neutral analytes. In addition, the electrostatic and hydrophobic interaction and the electrophoretic migration play a significant role in separation of the ionic or ionizable analytes.     

Capillary electrochromatography of 1-phenyl-3-methyl-5-pyrazolone derivatives of some mono-and disaccharides

Summary A packing procedure was adopted for capillary electrochromatography (CEC) that produces capillary columns with high separation efficiencies. The columns were fully packed, 50 cm long, with UV detection being performed through the packed section 30 cm from the inlet end. The CEC experiments were run at ambient pressure, with no additional pressure applied to the ends of the column. The stationary phase (octadecyl silica (ODS), 5 μm) promoted a high velocity electroosmotic flow (EOF), enabling rapid and efficient separation of a hydrocarbon test mixture. Some 1-phenyl-3-methyl-5-pyrazolone (PMP) derivatives of mono- and disaccharides were baseline separated, using a 5 mM NaH₂PO₄ in 80% acetonitrile and 20% water (v/v) buffer solution. CEC shows promise for future applications in carbohydrate analysis. Presented at Balaton Symposium on High Performance Separation Methods, Siófok, Hungary, September 1–3, 1999     

Cyclodextrin-mediated micellar electrokinetic chromatography and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry for the enantiomer separation of racemorphan in human urine.

Micellar electrokinetic chromatography (MEKC) was successfully and conveniently applied to the chiral separation with the addition of cyclodextrins (CDs) as chiral selector to the running buffer. Chiral separation depended on the type of CD; in particular, beta-CD was effective for the chiral separation of racemorphan. We investigated the optimal conditions of type and concentration of CD as chiral selector for the routine enantiomeric separation of racemorphan with good reproducibility. The effects of other parameters such as buffer pH and detection wavelength were also investigated to obtain the optimum conditions for the enantiomeric separation of racemorphan. Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry was used for confirmation of racemorphan. The optimal conditions for enantiomeric separation of the racemorphan were as follows: 50 mM borate buffer at pH 9.4 with 50 mM SDS, 10 mM beta-CD and 20% 1-propanol, 57 cm x 50 microns fused-silica capillary column, and UV detection at 192 nm. Based on the developed method, racemorphan in human urine was also separated and determined using solid-phase extraction and MEKC.     

Capillary electrochromatography of biologically relevant flavonoids

Flavonoids were separated utilizing CEC technique. Baseline separation of biologically relevant flavonoids was obtained using a 100 microm ID fused-silica capillary filled with 3 microm Silica-C18 material and an optimized mobile phase comprising of 20 mM Tris-HCl (pH 6.5), ACN and water at a ratio of 10/40/50 v/v/v. Separations were carried out at 25 kV and a column temperature of 25 degrees C. The influence of relevant parameters for the CEC separation, such as buffer concentration, pH, separation voltage, and ACN concentration, was investigated and optimized. Dependencies of the electroendoosmotic flow (EOF) on these parameters and effects on the resolution of the analytes were studied. During analyses the solvents used for dissolving the samples turned out to have significant effects on the separation of flavonoids. The optimized system was then successfully used for the separation of the flavonoids epicatechin, myricetin, quercetin, naringenin, and hesperetin. CEC turned out to be a useful complementary tool for the economic analysis of flavonoids in addition to common HPLC, muHPLC, and CE methodologies. This method can be used for real applications in phytomics.     

藏药蕨麻多糖水解单糖的毛细管区带电泳分离研究

以1-萘基-3-甲基-5-吡唑啉酮(NMP)为柱前衍生试剂,探讨了毛细管区带电泳模式下对藏药蕨麻多糖水解液中单糖的分离条件。实验采用58.5 cm×50μm i.d.毛细管(有效长度50 cm),55 mmol/L硼酸盐缓冲溶液(pH=9.46),柱温20℃,分离电压22 kV,进样10 s。该法不加任何添加剂,9种单糖可高效、快速基线分离,实现了对藏药蕨麻多糖水解液中单糖的分离和定量分析,结果令人满意。     

糖类衍生物在毛细管区带电泳下的分离研究

以新合成的1-萘基-3-甲基-5-吡唑啉酮(NMP)为柱前衍生试剂,采用毛细管区带电泳模式考察并优化了糖类衍生物的分离条件。实验采用58.5cm×50μmi.d.毛细管(有效柱长50cm),55mmol/L硼酸盐缓冲溶液(pH9.46),柱温20℃,分离电压22kV,进样10s,在不加任何添加剂的情况下,高效、快速地实现了9种糖的基线分离,并在最优化条件下进行了唐古特白刺实际样品的分离分析,结果令人满意。     

Determination of sulfonamide residues in cultured sea cucumber by pre-column derivatization capillary electrophoresis with fluorescence detection

A simple and mild method for the separation of sulfonamide residues based on a condensation reaction with O-phthalaldehyde solution (OPA) as labeling reagent with capillary electrophoresis has been developed. A 58.5 cm × 50 μm i.d. (50 cm effective length) untreated fused-silica capillary was used. To optimize the separation conditions, the background electrolyte concentration, pH, column temperature, voltage and other factors were evaluated. The optimal separation conditions were as follows: 20 mmol L^?1 borate buffer; pH 9.1; column temperature 20 °C; separation voltage 18 kV, pressure 50 mbar and injection time 8 s. Under the optimal conditions, 10 kinds of sulfonamide derivatives could be well-separated within 8 min, and the linear ranges were 0.35–100 μg kg^?1. The detection limit (at a signal-to-noise ratio of 3) was in the range of 0.12–0.25 μg kg^?1, and the quantification limit (at a signal-to-noise ratio of 10) was in the range of 0.35–0.70 μg kg^?1. The sulfonamide residues from cultured sea cucumber samples were determined under the optimal conditions with satisfactory results.     

A capillary zone electrophoresis for determination of thiolic peptides in biological samples

A new method to improve the analyses of thiolic peptides (cysteine, γGlu-Cys, glutathione, phytochelatins and desglycyl-phytochelatins) derivatized with monobromobimane (mBrB) in complex biological samples by CZE is described. The method involves a SPE using Sep-Pak Light C18 Cartridges after derivatization and a later CZE analysis. Elution of mBrB-thiols was achieved with 10 mM HCl + 70% methanol v/v in deionised water. Electrophoretic parameters, such as BGE pH and concentration, different organic additives (methanol and trifluoroethanol), applied voltage and capillary length were studied in order to establish suitable analytical conditions. Optimum separation of the mBrB-thiolic peptides was obtained with 100 mM sodium borate buffer at pH 7.60. The electrophoretic conditions were +15 kV, capillary length of 90 cm from inlet to detector (98 cm total length, 50 μm ID), samples were loaded into the capillary by hydrodynamic injection (50 mbar, 20 s) and detection was performed at 390 nm. The improved method showed good reproducibility, linearity and sensitivity. The LODs and LOQs estimated using a standard of GSH were 1.41 and 4.69 μM respectively.     

Efficient capillary electrophoresis separation and determination of free amino acids in beer samples

Simultaneous detection of various o‐phthalaldehyde (OPA)‐labeled amino acids (AAs) in food samples was reported based on CE separation. Ionic liquid was used for the first time for CE analysis of AAs with in‐capillary derivatization. Several other additives, including SDS, α/β‐CD, and ACN, as well as key parameters for CE separation (buffer pH value, separation voltage), were also investigated. Our results show that the multiple additive strategy exhibits good stable and repeatable character for CE analysis of OPA‐labeled AAs, for either in‐capillary derivatization or CE separation, and allows simultaneous quantification of different OPA‐labeled AAs in a large concentration range of 50 μM to 3.0 mM with LOD down to 10 μM. Seventeen OPA‐labeled AAs, except for two pairs of AAs (His/Gln and Phe/Leu), which were separated with resolutions of 1.1 and 1.2, respectively, were baseline separated and identified within 23 min using the present multiple additive strategy. The method was successfully applied for simultaneous analysis of AAs in seven beer samples and as many as eleven trace‐amount AAs were detected and quantified, indicating the valuable potential application of the present method for food analysis.     

Comparision of succinate- and phthalate-functionalized etched silica hydride phases for open-tubular capillary electrochromatography

Two open-tubular (OT) capillary electrochromatographic (CEC) columns were prepared by chemically bonding ionizable mono-(2-(methacryloyloxy)ethyl) succinate (MES) and phthalate-functionalized (MEP) ligands onto silica hydride-based phases through surface etching, silanization, and hydrosilation reactions, starting with a bare fused-silica tube. An analysis of the effect of performance of electrophoretic flow (EOF) on the changes in pH values, ionic strength, and the amount of acetonitrile modifiers helped to reveal that some silanol groups remained in the surface composite of the modified capillaries and to prove that MEP capillaries actually exerted greater EOF than MES ones. To explore the potential utilization of these two columns in various fields, three categories of samples, which spanned a wide range of polarities, were prepared and analyzed through many systematic trials of optimizing CEC conditions. For the separation of a mixture of nucleosides and thymine, guanine and adenine with purine uncleobases, which exhibit greater aromaticity than pyrimidine nucleobases, performed a higher retention in the MEP capillary through a π–π interaction than in the MES capillary. While four steroids were used as test samples, their migration order revealed that the MES stationary phase is hydrophilic in comparison with the MEP. An addition of methanol modifier (30%, v/v) into 10 mM borate buffer (pH 9.55 for MEP; pH 10.0 for MES) was necessary to accomplish a baseline separation of nine flavonoids in the MEP and MES capillaries. Studies on the elution order of these solutes revealed the presence of chromatographic activity in addition to electrophoretic migration. Especially in the MEP capillary, hydrophobic characteristics and π–π interactions with aromatic solutes were found and further improved to resolve an enantiomeric pair, catechin and epicatechin. Overall, the hydride-based stationary phases with ionizable ligands were successfully applied to the OT-CEC separations, and these results confidently propose an ideal route to the synthesis of a novel OT-CEC column.     

Determination of histamine and histidine by capillary zone electrophoresis with pre-column naphthalene-2,3-dicarboxaldehyde derivatization and fluorescence detection

A rapid and sensitive method was developed for the simultaneous determination of histamine and histidine by capillary zone electrophoresis with lamp-induced fluorescence detection. A fluoregenic derivatization reagent, naphthalene-2,3-dicarboxaldehyde (NDA) was successfully applied to label the histamine and histidine respectively. The derivatization conditions and separation parameters including pH and concentration of electrolyte and sample injection were optimized in detail. The optimal derivatization reaction was performed with 1.0 mM NDA, 20 mM NaCN, and 20 mM borate buffer, pH 9.1 for 15 min. The separation of NDA-tagged histamine and histidine could be achieved in less than 200 s with 40 mM phosphate buffer (pH 5.8) as the running buffer. The detection limits for histamine and histidine were 5.5 x 10(-9) and 3.8 x 10(-9) M, respectively (S/N = 3). The relative standard derivations for migration time and peak height of derivatives were less than 1.5 and 5.0%, respectively. The method was successfully applied to the analysis of histamine and histidine in the P815 mastocytoma cells and the beer samples.     

Zirconia nanoparticles-coated column for the capillary electrochromatographic separation of iron-binding- and phosphorylated-proteins

A ZrO(2) nanoparticles (ZrO(2)NPs)-coated column was prepared through a sol-gel process using zirconium(iv) oxychloride, which reacted with silanol groups of the fused-silica capillary. The condensation reaction was carried out at 350 °C for 8 h. Electroosmotic flow (EOF) measurements and scanning electron microscopy (SEM) images were used to characterize the ZrO(2)NPs fabricated on the inner wall of the capillary. Below the pI value (pH 5-6), cathodic EOF elucidated that the phosphate buffer adsorbs tightly on the zirconia surface, resulting in a negatively charged surface. In this work, iron-binding proteins, phosphorylated proteins and glycoproteins were selected as the model compounds. The effects of pH, concentration, buffer type and the organic modifier were studied to optimize the separation efficiency. Iron-binding proteins exhibited a retention time for myoglobin (Mb) < hemoglobin (Hb), which corresponded to the binding constants for ZrO(2)NPs. The α- and β-subunit of Hb could be separated in borate buffer (20 mM, pH 9.0) with MeOH (20%, v/v). Greater affinity of α-casein and bovine serum albumin (BSA) for the stationary phase as the pH decreased was found by comparison with that of conalbumin (ConA) and transferrin (Tf). Interestingly, 14 peaks for glycoisoforms of ovalbumin (OVA) were observed using borate buffer (40 mM, pH 9.0). The established method was also applied to the determination of analytes in the egg whites of chicken and duck eggs.     

Capillary electrophoresis of nonprotein and protein amino acids without derivatization

An efficient separation of eleven nonprotein amino acids (NPAAs) and three protein amino acids containing aromatic moieties was achieved by capillary electrophoresis without derivatization. The fourteen amino acids were well separated with a 100 mM sodium phosphate run buffer (pH 2.0) using a 57 cm fused-silica capillary (50 microm ID, 50 cm effective length) at 20 degrees C. With an electric field of 351 V/cm, the time needed for the separation was less than 20 min. Under optimum conditions, excellent linear responses were obtained in the concentration range of 5-100 microM, with the linear correlation coefficient ranging from 0.9785 or greater. The relative standard deviations of the migration times and the corrected peak areas were found to be 1.5-3.9% and 8.0-11.5%, respectively. In order to improve the limit of detection (LOD), simple stacking and large volume stacking using an EOF pump (LVSEP) methods were used. Improved LODs were about 300 nM in stacking and below 15 nM for five small NPAAs in LVSEP.