金核银壳纳米粒子薄膜的制备及SERS活性研究

采用柠檬酸化学还原法制备金溶胶, 通过自组装技术在石英片表面制备金纳米粒子薄膜, 在银增强剂混合溶液中反应获得金核银壳纳米粒子薄膜. 用紫外-可见吸收光谱仪和原子力显微镜(AFM)研究了不同条件下制备的金核银壳纳米粒子薄膜的光谱特性和表面形貌, 并以结晶紫为探针分子测量了金核银壳纳米粒子薄膜的表面增强拉曼光谱(SERS). 结果表明, 金纳米粒子薄膜的分布、银增强剂反应时间的长短对金核银壳纳米粒子薄膜的形成均有重要影响. 制备过程中, 可以通过控制反应条件获得一定粒径的、具有良好表面增强拉曼散射活性的金核银壳纳米粒子薄膜.     

FeOOH明胶复合纳米粒子的制备与表征

采用两步法制备具有弱磁性的FeOOH纳米粒子和FeOOH明胶复合纳米粒子. 透射电镜、扫描电镜、红外光谱、X射线衍射和磁滞回线等测量结果表明: 在一定FeCl₃/Fe₂(SO₄)₃/H₂O摩尔比条件下, 加入十二烷基苯磺酸钠(ABS)溶液, 可制备粒径为30～150 nm弱磁性FeOOH纳米粒子, 其磁性可达6.5×10^－6 emu/g. 弱磁性FeOOH纳米粒子可被明胶包裹. 随着FeCl₃/Fe₂(SO₄)₃摩尔比减小或明胶浓度增加, 纳米球粒径增大, 磁性降低. 随着固化时间增加, FeOOH明胶复合纳米粒子的粒径先增大后减小.     

嵌段聚合物修饰的金纳米粒子的制备及表征

通过RAFT合成聚(甲基丙烯酸缩水甘油酯)-b-聚(乙二醇甲基丙烯酸酯)嵌段共聚物(PGMA-bPMAPEG),再用半胱氨酸(Cys)使PGMA中的环氧基团开环,制备含有巯基的两亲水嵌段聚合物PMAPEG-bP(GMA-Cys)。并以其作为修饰剂,通过原位还原法使HAuCl4在NaBH4的还原下制备金/聚合物纳米复合粒子(Au@PMAPEG-b-P(GMA-Cys)NPs)。经FT-IR、UV-vis、TG、XRD、TEM和DLS表征,发现金纳米复合粒子呈均匀分散的球形,平均粒径约为10nm,在527nm处出现了金纳米粒子的表面等离子共振吸收峰,金约占总重量的49%。由于外层嵌段共聚物的修饰作用,金纳米复合粒子在室温下放置6个月未发生粒子间的聚集。     

电化学沉积法制备金（核）-铜（壳）纳米粒子阵列

以组装在有机分子自组装膜/金基底电极上的Au纳米粒子阵列为电化学沉积模板,制备了金(核)-铜 (壳)纳米粒子阵列.选用巯基十一胺（AUDT）和巯基癸烷（DT）混合自组装膜作为基底电极与Au纳米粒子的耦联层,可以在一定的电位下实现金属Cu在Au纳米粒子上的选择性沉积.将沉积电位控制在－0.03 V（vs SCE）时,沉积初期（t ≤ 15 s,沉积粒子粒径 ≤ 20 nm ）金(核)-铜 (壳)粒子具有良好的单分散性和近似球形,而且粒径实验值同计算值非常吻合.     

复合纳米材料Cu2O@Au对水体中罗丹明B的检测应用研究

制备了多面体Cu2 O纳米粒子,利用Cu2 O的还原性,在其表面原位生成了不同密度的Au纳米粒子,制备了Au、Cu共同增强拉曼信号的复合纳米粒子Cu2 O@Au.利用透射电镜(TEM)、扫描电镜(SEM)、X射线衍射(XRD)等对制备的Cu2 O和Cu2 O@Au的形貌、粒径、表面性能等进行了表征.研究了Cu2 O表面金纳米粒子的分布密度对水样中目标检测物罗丹明B的拉曼增强效果.结果表明,氯金酸浓度在1 mmol/L时制备的Cu2 O@Au表面均匀覆盖一层金纳米粒子,其表面增强拉曼效果最为显著,对水样中罗丹明B检测范围为1×10-2~5×10-6 mol/L.研究了此探针在PBS(1×)和酸性水溶液(0.01 mol/L HCl)中的稳定性,并将其用于沂河水样中靶标的检测实验,结果表明,其稳定性较好.     

二苯胺磺酸钠还原法制备粒径可控的金纳米粒子

采用二苯胺磺酸钠还原四氯合金酸的方法,在室温条件下,用SDS(十二烷基硫酸钠)、SDBS(十二烷基苯磺酸钠)作表面活性剂,成功地合成了金纳米粒子.分别讨论了还原剂二苯胺磺酸钠、表面活性剂(SDS、SDBS)及四氯台金酸的浓度等对金纳米粒子的粒径和形貌的影响.通过控制反应条件,可以合成出平均粒径大约为10、14、30、36nm的金纳米粒子.利用透射电镜(TEN)、紫外-可见(UV-Vis)吸收光谱对金纳米粒子进行了表征.研究结果表明不同的SDS或SDBS/HAuCl4的摩尔比,对金纳米粒子的尺寸大小有影响.     

Fe3O4表面原位引发可控/“活性”聚合制备磁性聚苯乙烯纳米粒子

采用化学共沉淀方法合成了Fe3O4纳米粒子, 用3-甲基丙烯酰氧基丙基三甲氧基硅烷(3-MPS)对其进行表面接枝修饰, 然后以苯乙烯(St)为单体, 过氧化苯甲酰(BPO)为引发剂, 4-羟基-2,2,6,6-四甲基哌啶-1-氧化物自由基(HTEMPO·)为稳定自由基介质, 采用可控/“活性”自由基聚合技术在修饰后的Fe3O4纳米粒子表面原位引发聚合, 制备了粒径小、分布窄、磁含量高的磁性聚苯乙烯（PS）纳米粒子. X射线衍射(XRD)研究表明, 所合成的Fe3O4粒子为尖晶石结构. 凝胶渗透色谱(GPC)分析表明, 聚苯乙烯的分子量与反应时间呈较好的线性关系. 透射电镜(TEM)观察表明, 所制备的磁性聚苯乙烯纳米粒子的粒径在20-30 nm之间. 热重(TG)分析得到磁性聚苯乙烯纳米粒子的磁含量为62.6%. 振动样品磁强计(VSM)测试结果表明, 磁性聚苯乙烯纳米粒子的比饱和磁化强度为31.7 emu·g-1, 呈现单磁畴结构.     

Papain/HA-Phe自组装复合纳米粒子及乳化性能

用L-苯丙氨酸乙酯(L-Phe)改性透明质酸(HA)双亲性生物大分子(HA-Phe)负载生物活性分子木瓜蛋白酶(papain),HA-Phe和Papain通过静电、氢键和疏水相互作用自组装形成生物基Papain/HA-Phe复合纳米粒子.用动态光散射(DLS)和透射电镜(TEM)对复合纳米粒子的尺寸和形貌进行表征.结果显示,形成的复合纳米粒子为球形结构,粒径约308 nm.以此复合纳米粒子为颗粒乳化剂稳定白油,形成水包油型Pickering乳液.乳液的扫描电镜(SEM)显示,复合纳米粒子吸附在油水界面,形成复合纳米粒子的吸附层以稳定乳液.详细研究了pH和盐浓度对复合纳米粒子性质和复合纳米粒子乳化性能的影响.结果表明,随着pH增加,复合纳米粒子在油滴表面的吸附数目减少,乳化性能降低;随着盐浓度增加,复合纳米粒子的形变能力增强,乳化性能提高.进一步研究了乳液中木瓜蛋白酶的活性及美白效果.研究表明,制备的乳液保留了一定的活性,且具有一定的美白效果.     

SiO2 /Au核壳结构纳米粒子的制备及表征

通过以金纳米粒子为表面晶种和壳生长的方法制备了金纳米壳包覆二氧化硅的复合纳米粒子。采用TEM 和UV-Vis对复合粒子进行了表征和研究，结果表明所得到的复合粒子粒径均匀、金纳米壳光滑完整，且壳厚度可通过反应物的用量来控制。当核半径与壳厚度之比在4到13之间变化时,复合粒子的光学共振峰在可见光区到近红外光区范围内可发生大于500 nm波长的移动。     

链霉亲和素-异硫氰酸荧光素偶联核壳型Fe_3O_4/Au纳米晶的合成及性质

采用改进的Polyol合成法,以PEO-PPO-PEO为表面活性剂制备了链霉亲和素-异硫氰酸荧光素偶联的Fe3O4/Au纳米粒子;利用透射电镜和X射线衍射仪分析证实了Fe3O4/Au的核壳型纳米结构,确定了其粒径和分布;采用紫外-可见吸收光谱仪和荧光光谱仪测定了所制备的纳米粒子的光学活性和荧光特性,并采用振动样品磁强计(VSM)测量了其磁化率.结果表明,所制备的Fe3O4/Au纳米粒子具有光学活性和荧光特性,以及优异的磁性.     

Preparation and electrorheological characteristic of CdS/Polystyrene composite particles

Cadmium sulfide/polystyrene (CdS/PS) hybrid particles were synthesized and their physical characteristics including electrorheology were examined. Monodisperse CdS/PS nanocomposite particles with diameters of 2 μm were obtained via dispersion polymerization. To form cadmium sulfide nanoparticles onto the PS surface, 2-(dimethylamino)ethyl methacrylate was used as a functional monomer for coordinating with Cd²⁺ ions. Finally, cadmium sulfide nanoparticles with size < 10 nm were formed with the release of S²⁻ ions from thioacetamide. The morphology of the as-prepared CdS/PS nanocomposite particles clearly showed that the CdS particles are present on the surface of the PS. The optical properties were also studied. In addition, their electrorheological characteristics were confirmed by using optical microscopy with applied electrical field. Recently, dielectric properties of CdS nanoparticles were already reported; however, electrorheological characteristics of CdS/PS nanocomposite particles were investigated for the first time.     

New preparation method of gold nanoparticles on SiO2

It is shown that adsorption of the [Au(en)(2)](3+) cationic complex can be successfully employed for the deposition of gold nanoparticles (1.5 to 3 nm) onto SiO(2) with high metal loading, good dispersion, and small Au particle size. When the solution pH increases (from 3.8 to 10.5), the Au loading in the Au/SiO(2) samples increases proportionally (from 0.2 to 5.5 wt %), and the average gold particle size also increases (from 1.5 to 2.4 nm). These effects are explained by the increase in the amount of negatively charged sites present on the SiO(2) surface, namely, when the solution pH increases, a higher number of [Au(en)(2)](3+) species can be adsorbed. Extending the adsorption time from 2 to 16 h gives rise to an increase in the gold loading from 3.3 to 4.0 wt % and in the average particle size from 1.8 to 2.9 nm. Different morphologies of gold nanoparticles are present as a function of the particle size. Particles with a size of 3-5 nm show defective structure, some of them having a multiple twinning particle (MTP) structure. At the same time, nanoparticles with an average size of ca. 2 nm exhibit defect-free structure with well-distinguishable {111} family planes. TEM and HAADF observations revealed that Au particles do not agglomerate on the SiO(2) support: gold is present on the surface of SiO(2) only as small particles. Density functional theory calculations were employed to study the mechanisms of [Au(en)(2)](3+) adsorption, where neutral and negatively charged silica surfaces were simulated by neutral cluster Si(4)O(10)H(4) and negatively charged cluster Si(4)O(10)H(3), respectively. The calculation results are totally consistent with the suggestion that the deposition of gold takes place according to a cationic adsorption mechanism.     

The role of pore size and structure on the thermal stability of gold nanoparticles within mesoporous silica

Highly dispersed gold particles (<2 nm) were synthesized within the pores of mesoporous silica with pore sizes ranging from 2.2 to 6.5 nm and different pore structures (2D-hexagonal, 3D-hexagonal, and cubic). The catalysts were reduced in flowing H2 at 200 degrees C and then used for CO oxidation at temperatures ranging from 25 to 400 degrees C. The objective of this study was to investigate the role of pore size and structure in controlling the thermal sintering of Au nanoparticles. Our study shows that sintering of Au particles is dependent on pore size, pore wall thickness (strength of pores), and pore connectivity. A combination of high-resolution TEM/STEM and SEM was used to measure the particle size distribution and to determine whether the Au particles were located within the pores or had migrated to the external silica surface.     

Aerosol assisted chemical vapor deposition using nanoparticle precursors: a route to nanocomposite thin films

Gold nanoparticle and gold/semiconductor nanocomposite thin films have been deposited using aerosol assisted chemical vapor deposition (CVD). A preformed gold colloid in toluene was used as a precursor to deposit gold films onto silica glass. These nanoparticle films showed the characteristic plasmon absorption of Au nanoparticles at 537 nm, and scanning electron microscopic (SEM) imaging confirmed the presence of individual gold particles. Nanocomposite films were deposited from the colloid concurrently with conventional CVD precursors. A film of gold particles in a host tungsten oxide matrix resulted from co-deposition with [W(OPh)(6)], while gold particles in a host titania matrix resulted from co-deposition with [Ti(O(i)Pr)(4)]. The density of Au nanoparticles within the film could be varied by changing the Au colloid concentration in the original precursor solution. Titania/gold composite films were intensely colored and showed dichromism: blue in transmitted light and red in reflected light. They showed metal-like reflection spectra and plasmon absorption. X-ray photoelectron spectroscopy and energy-dispersive X-ray analysis confirmed the presence of metallic gold, and SEM imaging showed individual Au nanoparticles embedded in the films. X-ray diffraction detected crystalline gold in the composite films. This CVD technique can be readily extended to produce other nanocomposite films by varying the colloids and precursors used, and it offers a rapid, convenient route to nanoparticle and nanocomposite thin films.     

纳米金-钛酸纳米管复合材料的合成与表征

以氯金酸和钛酸钠米管(NTA)为原料,柠檬酸三钠为稳定剂,硼氢化钠为还原剂,于室温条件下合成了一种金纳米颗粒-钛酸纳米管(GNPs-NTA)复合纳米材料;利用红外光谱仪、透射电镜、X射线粉末衍射仪等分析了产物的化学键合特征、微结构及相组成,并考察了产物对辣根过氧化酶(HRP)结构和生理活性的影响.结果表明,合成的纳米金颗粒粒径(平均5.3nm)分布窄,且均匀分布于钛酸纳米管表面.此外,HRP与GNPs-NTA复合纳米材料充分振荡混合后仍能保持其二级结构不变,有利于保持其生理活性.     

Crystallization of Liquid Gold Nanoparticles by Molecular Dynamics Simulation

Molecular dynamics simulation of the crystallization behavior of liquid gold (Au) nanoparticles, with 1, 2, 3, 4, 5 and 6 nm in diameter, on cooling has been carried out based on the embedded-atom-method potential. With decreasing cooling time, the final structure of the particle changes from amorphous to crystalline structure. We showed that the structure of the fully crystallized particle is polycrystalline face-centered cubic (FCC). The FCC structure of the gold nanoparticle is proved energetically the most stable form. And the final structure of nanoparticles is affected by cooling time and size of nanoparticles. We also showed that the melting point of particles is affected by size of nanoparticles.     

Polypyrrole-palladium nanocomposite coating of micrometer-sized polymer particles toward a recyclable catalyst

A range of near-monodisperse, multimicrometer-sized polymer particles has been coated with ultrathin overlayers of polypyrrole-palladium (PPy-Pd) nanocomposite by chemical oxidative polymerization of pyrrole using PdCl(2) as an oxidant in aqueous media. Good control over the targeted PPy-Pd nanocomposite loading is achieved for 5.2 μm diameter polystyrene (PS) particles, and PS particles of up to 84 μm diameter can also be efficiently coated with the PPy-Pd nanocomposite. The seed polymer particles and resulting composite particles were extensively characterized with respect to particle size and size distribution, morphology, surface/bulk chemical compositions, and conductivity. Laser diffraction studies of dilute aqueous suspensions indicate that the polymer particles disperse stably before and after nanocoating with the PPy-Pd nanocomposite. The Fourier transform infrared (FT-IR) spectrum of the PS particles coated with the PPy-Pd nanocomposite overlayer is dominated by the underlying particle, since this is the major component (>96% by mass). Thermogravimetric and elemental analysis indicated that PPy-Pd nanocomposite loadings were below 6 wt %. The conductivity of pressed pellets prepared with the nanocomposite-coated particles increased with a decrease of particle diameter because of higher PPy-Pd nanocomposite loading. "Flattened ball" morphologies were observed by scanning/transmission electron microscopy after extraction of the PS component from the composite particles, which confirmed a PS core and a PPy-Pd nanocomposite shell morphology. X-ray diffraction confirmed the production of elemental Pd and X-ray photoelectron spectroscopy studies indicated the existence of elemental Pd on the surface of the composite particles. Transmission electron microscopy confirmed that nanometer-sized Pd particles were distributed in the shell. Near-monodisperse poly(methyl methacrylate) particles with diameters ranging between 10 and 19 μm have been also successfully coated with PPy-Pd nanocomposite, and stable aqueous dispersions were obtained. The nanocomposite particles functioned as an efficient catalyst for the aerobic oxidative homocoupling reaction of 4-carboxyphenylboronic acid in aqueous media for the formation of carbon-carbon bonds. The composite particles sediment in a short time (相似文献   

交联核壳结构PBA/PS和PBA/PMMA纳米微球的制备与应用

考察了聚丙烯酸丁酯/聚苯乙烯(PBA/PS)以及聚丙烯酸丁酯/聚甲基丙烯酸甲酯(PBA/PMMA)交联核壳结构纳米高分子微球的制备方法,并对其在尼龙复合材料中的应用进行了初步研究.结果表明,通过交联剂的引入使粒子核层和壳层内部均形成了高度交联的结构,可以限制亲水性较小的聚苯乙烯(PS)壳层向粒子内部迁移的趋势;制备出的微球平均粒径为40~50 nm,粒径分布很窄.采用饥饿态加料方式加入第二单体不仅可以使微球具有较高的产率和凝胶率,而且可以使其具有更理想的核壳结构和更窄的粒径分布.此外,将合成出的PBA/PMMA核壳粒子对尼龙6基体进行复合的结果表明,由于该微球表面与尼龙6基体之间具有较强的界面相互作用且微球具有较大的形变能力,可以在基体中形成良好的分散,在保持材料强度的同时有效地提高了其刚性和韧性.     

Binary Au/MWCNT and Ternary Au/ZnO/MWCNT Nanocomposites: Synthesis,Characterisation and Catalytic Performance

Gold nanoparticles of 10–24 and 5–8 nm in size were obtained by chemical citrate reduction and UV photoreduction, respectively, on acid‐treated multiwalled carbon nanotubes (MWCNTs) and on ZnO/MWCNT composites. The shape and size of the deposited Au nanoparticles were found to be dependent upon the synthetic method used. Single‐crystalline, hexagonal gold particles were produced in the case of UV photoreduction on ZnO/MWCNT, whereas spherical Au particles were deposited on MWCNT when the chemical citrate reduction method was used. In the UV photoreduction route, n‐doped ZnO serves as the e^? donor, whereas the solvent is the hole trap. All materials were fully characterised by UV/Vis spectroscopy, scanning electron microscopy, transmission electron microscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy and BET surface analysis. The catalytic activity of the composites was studied for the selective hydrogenation of α,β‐unsaturated carbonyl compound 3,7‐dimethyl‐2,6‐octadienal (citral). The Au/ZnO/MWCNT composite favours the formation of unsaturated alcohols (selectivity=50 % at a citral conversion of 20 %) due to the presence of single‐crystalline, hexagonal gold particles, whereas saturated aldehyde formation is favoured in the case of the Au/MWCNT nanocomposite that contains spherical gold particles.