偶联剂原位改性SiO2提高PEO/LiClO4/SiO2电导率

偶联剂原位改性SiO2提高PEO/LiClO4/SiO2电导率;PEO;聚合物电解质;偶联剂;SiO2;电导率     

PEO-LiClO_4-ZSM5复合聚合物电解质II.ZSM-5对离子电导率的影响

通过XRD ,DSC ,FT IR和SEM等方法对PEO LiClO4 ZSM5复合电解质进行了研究 ,结果表明ZSM 5可以有效地降低PEO LiClO4 ZSM5复合电解质中PEO的结晶度和玻璃化温度 ,从而提高其低温区域的离子电导率 .温度高于PEO的结晶熔融温度后 ,复合电解质离子电导率的提高则是由于在ZSM 5表面形成了有利于Li离子迁移的导电通道所引起的 .较高的离子电导率和较宽的电化学稳定窗口表明PEO LiClO4 ZSM5复合电解质在全固态锂离子二次电池领域具有良好的应用前景 .     

PEO/LiClO_4纳米SiO_2复合聚合物电解质的电化学研究

将实验室制备的纳米二氧化硅和市售纳米二氧化硅粉末与PEO LiClO4复合 ,制得了复合PEO电解质 .它们的室温离子电导率可比未复合的PEO电解质提高 1～ 2个数量级 ,最高可以达到 1 2 4× 10 - 5S cm .离子电导率的提高有两方面的原因 :一是无机二氧化硅粉末的加入抑制了PEO的结晶 ,是二氧化硅粉末和聚合物电解质之间形成的界面对电导率的提高也有一定的作用 .在进一步加入PC EC(碳酸丙烯酯 碳酸乙烯酯 )混合增塑剂后制得的复合凝胶PEO电解质 ,可使室温离子电导率再提高 2个数量 ,达到 2× 10 - 3 S cm .用这种复合凝胶PEO电解质组装了Li|compositegelelectrolyte|Li半电池 ,并测量了该半电池的交流阻抗谱图随组装后保持时间的变化 ,实验观察到在保持时间为 144h以内钝化膜的交流阻抗迅速增大 ,但在随后的时间内逐渐趋于平稳 ,表明二氧化硅粉末的加入可以有效地抑制钝化膜的生长     

原位复合法制备(PEO)8LiClO4/TiO2聚合物电解质的研究

以聚氧化乙烯/高氯酸锂复合物[(PEO)8LiClO4]为基体,通过钛酸丁酯的水解缩合反应在其中原位生成TiO2,制备了(PEO)8LiClO4/TiO2复合聚合物电解质,采用SEM、DSC和交流阻抗方法研究了聚合物电解质的形态、玻璃化转变温度(Tg)、结晶度(Xc)和离子导电性能.结果表明原位生成的TiO2在基体中分散均匀,加入TiO2后聚合物电解质体系的Tg和Xc均有所降低,而电导率明显提高,当TiO2添加量为ω=0.05时电导率达到最大值5.5×10-5S·cm-1(20℃).     

碱性纳米复合聚合物电解质研究

为了提高聚氧化乙烯(PEO)/KOH 基碱性聚合物电解质的电导率, 制电解质膜时分别将纳米 TiO2、纳米β-Al2O3和纳米 SiO2添加到 PEO/KOH 体系中, 制备出了兼顾电学和力学性能的碱性纳米复合聚合物电解质. 交流阻抗测试显示, 其室温(28 ℃)电导率可达到 10-3 S?cm-1数量级. 循环伏安研究表明, 制得的电解质膜在不锈钢惰性电极上的电化学稳定窗口约为 1.6 V. 分别研究了聚合物电解质膜中 KOH, H2O, 无机纳米粉末的含量以及温度对体系电导率的影响.     

基于PEO的复合聚合物电解质的研究进展

从填料对聚合物电解质性能的影响、复合聚合物电解质性能的影响因素、聚合物电解质的结构和复合聚合物电解质的应用四方面综述了基于聚氧化乙烯（PEO）的复合聚合物电解质研究的最新进展。聚合物中加入纳米级无机填料可提高聚合物电解质的机械强度、电导率和锂／电解质界面的稳定性。     

表面改性纳米SiO2复合聚合物电解质的制备及性能

通过化学方法将具有增塑效果的环状碳酸酯基团引入纳米SiO2表面,并用FTIR与TGA对改性纳米SiO2进行了表征.将改性纳米SiO2添加到以聚氧化乙烯(PEO)为基体的聚合物电解质中,制备了复合聚合物电解质.通过DSC和交流阻抗等方法对该聚合物电解质膜的热力学和电化学性能进行了研究.结果表明,掺杂改性纳米SiO2的聚合物电解质具有更高的离子电导率,室温最高离子电导率可达到1.84×10-5 S/cm;具有较高的锂离子迁移数,最高可达到0.49,且具有更好的界面稳定性.     

相态结构对聚氧化乙烯/丁二腈/高氯酸锂复合电解质室温电导率的影响

采用聚氧化乙烯(PEO)、丁二腈和高氯酸锂(LiClO4)的复合电解质体系, 制备了一系列不同配比的PEO/SN/LiClO4复合电解质, 对其室温电性能和相态结构进行了表征, 并探讨了相态结构对室温电导率的影响.     

纳米阻燃氢氧化镁/聚氧化乙烯复合聚合物电解质

合成了纳米氢氧化镁作为聚氧化乙烯(PEO)基聚合物电解质的增塑剂和阻燃剂,并对其进行X射线衍射(XRD)、透射电子显微镜(TEM)和热重(TG)分析研究.制得的氢氧化镁为片状六方晶体,尺寸在50-80nm之间,纳米氢氧化镁在340℃时开始热分解.对纳米氢氧化镁/PEO复合聚合物电解质的电化学研究结果显示:纳米氢氧化镁/PEO复合聚合物电解质的离子电导率随着添加纳米氢氧化镁的质量分数的增加先增大后减小,其在5%-10%之间时,复合聚合物电解质的离子电导率达到最大值.纳米氢氧化镁的添加使复合聚合物电解质的阳极氧化电位有一定程度的提高,纳米氢氧化镁具有改善PEO阳极抗氧化能力的作用.     

水蒸气沉淀法制备SiO2/偏氟乙烯-六氟丙烯共聚物复合微孔型聚合物电解质的研究

用水蒸气沉淀法制备了SiO2 偏氟乙烯 六氟丙烯共聚物 [P(VDF HFP) ]复合微孔型聚合物电解质 ,并研究了纳米SiO2 的加入对微孔结构及复合微孔型聚合物电解质性能的影响 .SEM观察发现当纳米SiO2 的添加量大于 0 1倍聚合物质量时 ,可以在微孔中观察到纳米粒子的严重团聚现象 .电导率的测量表明添加 0 0 5倍聚合物质量的纳米SiO2 后 ,微孔型聚合物电解质的电导率有明显提高 ,但进一步增大添加量后 ,电导率有所下降 .另外 ,实验发现添加纳米SiO2 可以明显提高微孔型聚合物电解质与锂金属电极之间的界面稳定性 ,特别是添加量为 0 0 5倍聚合物质量时的效果良好 .     

High ionic conductivity of all-solid polymer electrolytes based on polyorganophosphazenes

A series of all-solid polymer electrolytes were prepared by cross-linking new designed poly(organophosphazene) macromonomers. The ionic conductivities of these all-solid, dimensional steady polymer electrolytes were reported. The temperature dependence of ionic conductivity of the all-solid polymer electrolytes suggested that the ionic transport is correlated with the segmental motion of the polymer. The relationship between lithium salts content and ionic conductivity was discussed and investigated by Infrared spectrum. Furthermore, the polarity of the host materials was thought to be a key to the ionic conductivity of polymer electrolyte. The all-solid polymer electrolytes based on these poly(organophosphazenes) showed ionic conductivity of 10⁻⁴ S cm⁻¹ at room temperature.     

Ion conducting properties of poly(ethylene oxide)-based electrolytes incorporating amorphous silica attached with imidazolium salts

Poly(ethylene oxide) (PEO)-based polymer electrolytes containing amorphous silica attached ionic liquid (IL) were studied in order to improve electrochemical and interfacial properties. An imidazolium salt such as IL was attached to modified ceramic fillers. The modified ceramic fillers were amorphous silica with the immobilized 1-methyl-3-propyl-imidazolium bromide (MPIm-AS). PEO-based polymer electrolytes were prepared by using the solution casting technique. In order to investigate the ionic conductivity, studies on the modified filler addition effects on the ion-conducting behavior of polymer electrolytes having specific amounts of MPIm-AS were carried out. The addition of MPIm-AS in polymer electrolytes has resulted in higher ionic conductivity at room temperature. The structure, crystallinity, and morphology of the solid polymer electrolytes were evaluated using X-ray diffraction, differential scanning calorimetry, and scanning electron microscope measurement. The ionic conductivity was measured by an AC impedance method. The enhanced conductivity was dependent on the decreased crystallinity and the changed morphologies of composites.     

聚合物固体电解质中的离子状态与导电机理的研究

制备得到了一种新颖的聚氨酯和丙烯酸酯复合梳形交联聚合物 (Combcross linkedpolymer) ,并以此聚合物为基体加入不同含量的高氯酸锂盐制得一系列聚合物固体电解质 ,其室温电导率可以达到 3 4× 10 - 5S·cm- 1 .通过Raman、DSC、SEM及电性能等研究了电解质中的盐浓度与离子存在状态及离子电导率之间的关系 .结果显示随着盐浓度的增加 ,聚合物固体电解质中离子对的比例和电导率都迅速增加 ,说明离子对 (由多个醚氧原子、阴离子和阳离子组成 )对体系导电起着积极的作用 .     

含硅氢键聚二硅氧烷/聚醚共混聚合物电解质 II. PSEMH对PEO结晶性能及离子电导率的影响

通过Raman,DSC和XRD等方法对PEO-PSEMH-LiClO4全固态共混聚合物电解质进行了研究,结果表明PSEMH能够显著地降低PEO-LiClO4电解质体系的PEO的结晶性和玻璃化转变温度,同时PSEMH分子的二硅醚链节中氧原子与Li+间具有配位作用,从而大幅提高x%PEO-y%PSEMH-LiClO4电解质在低温区的离子电导率。而当PSEMH交联硫化之后,虽然降低了PEO的结晶度和Tg,但是由于PSEMH的交联网络限制了聚合物链段的运动性,使得电解质的离子电导率在低温区高于100%PEO-LiClO4(约为12倍),而在高温区则低于100%PEO-LiClO4,充分证明了PSEMH对电解质的离子电导率的具有显著的贡献作用。     

Polymer electrolytes based on room temperature ionic liquid: 2,3-dimethyl-1-octylimidazolium triflate

Room temperature ionic liquid (DMOImTf) based upon 2,3-dimethyl-1-octylimidazolium cation and trifluoromethanesulfonate or triflate (CF(3)SO(3))(-) anion has been synthesized and shows conductivity of 5.68 mS/cm and viscosity of 26.4 cP at 25 degrees C. Ion conducting polymer electrolytes based on polymers (poly(ethylene oxide) (PEO) and polyvinylidenefluoride-co-hexafluoropropylene (PVdF-HFP)) and ionic liquid (DMOImTf) were prepared in film form by the casting technique. The conductivity of polymer electrolytes containing 0.5 M LiCF(3)SO(3) in PEO:DMOImTf taken in equal weight ratio increases with the addition of propylene carbonate (PC) while its mechanical stability improved by dispersing nanosize fumed silica. However, polymer electrolytes containing PVdF-HFP and ionic liquid show a high value of conductivity (10(-4)-10(-3) S/cm) alongwith better mechanical stability.     

P(VAc-MA)/PMMA为基体的聚合物电解质制备及其在电致变色器件中的应用

以醋酸乙烯酯(VAc)和丙烯酸甲酯(MA)为单体, 采用半连续种子乳液聚合法制备了无规共聚物P(VAc-MA), 以PMMA与P(VAc-MA)的共混物为基体制备了聚合物电解质. 用红外光谱(FTIR)、X射线衍射(XRD)、热重分析(TG)、紫外光谱(UV)、力学性能测试及电化学交流阻抗等方法研究了聚合物、聚合物膜和聚合物电解质的性质. 结果表明, VAc与MA通过打开各自的CC键聚合生成P(VAc-MA); P(VAc-MA)与PMMA共混后结晶状态发生了变化, 增加了无定形相区, 降低了链段运动的能量壁垒, 提高了热稳定性和拉伸强度. 以P(VAc-MA)/PMMA为基体的聚合物电解质膜具有很高的透明性, 最大室温电导率达到1.17×10-3 S/cm; 离子电导率随着温度的升高而迅速增加, 电导率-温度曲线符合Arrhenius方程; 将此电解质用于全固态电致变色显示器件显示出优良的性能.     

Ionic liquids to the rescue? Overcoming the ionic conductivity limitations of polymer electrolytes

Polymer electrolytes – solid polymeric membranes with dissolved salts – are being intensively studied for use in all-solid-state lithium-metal-polymer (LMP) batteries to power consumer electronic devices. The low ionic conductivity at room temperature of existing polymer electrolytes, however, has seriously hindered the development of such batteries for many applications. The incorporation of salts molten at room temperature (room temperature ionic liquids or RTILs) into polymer electrolytes may be the necessary solution to overcoming the inherent ionic conductivity limitations of ‘dry’ polymer electrolytes.     

Conductive networked polymer gel electrolytes composed of poly(meth)acrylate,lithium salt,and ionic liquid

Self‐standing films of (meth)acrylate‐based polymer gel electrolytes with high ionic liquid content (80 wt %) were prepared by in situ thermally or photo induced radical copolymerization of mono‐functional and di‐functional (meth)acrylates in an ionic liquid in the presence/absence of a lithium salt. Their ionic conductivity, thermal property, mechanical property, and flammability were examined. 1‐Ethyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide (EMImTFSI) or 1‐ethyl‐3‐methylimidazolium bis(fluorosulfonyl)imide (EMImFSI) was used as the ionic liquid, and lithium bis(trifluoromethanesulfonyl)imide LiTFSI was used as the lithium salt. The obtained films were semitransparent and flexible with good to moderate thermal stability and mechanical strength with high ionic conductivity. The EMImFSI‐containing gel electrolytes showed higher ionic conductivity than the corresponding EMImTFSI‐containing gel electrolytes. The ionic conductivity in the acrylate‐based gel electrolytes was slightly increased by addition of lithium salt, while that in the corresponding methacrylate‐based electrolytes was decreased significantly. The flame test showed the ionic liquid containing networked polymer gel electrolytes to have low if any flammability and was therefore confirmed to be highly safe. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Safety-enhanced Polymer Electrolytes with High Ambient-temperature Lithium-ion Conductivity Based on ABA Triblock Copolymers

Liquid electrolytes used in lithium-ion batteries suffer from leakage,flammability,and lithium dendrites,making polymer electrolyte a potential alternative.Herein,a series of ABA triblock copolymers(ABA-x)containing a mesogen-jacketed liquid crystalline polymer(MJLCP)with a polynorbornene backbone as segment A and a second polynorbornene-based polymer having poly(ethylene oxide)(PEO)side chains as segment B were synthesized through tandem ring-opening metathesis polymerizations.The block copolymers can self-assemble into ordered morphologies at 200℃.After doping of lithium salts and ionic liquid(IL),ABA-x self-assembles into cylindrical structures.The MJLCP segments with a high glass transition temperature and a stable liquid crystalline phase serve as physical crosslinking points,which significantly improve the mechanical performance of the polymer electrolytes.The ionic conductivity of ABA-x/lithium salt/IL is as high as 10-3 S·cm-1 at ambient temperature owing to the high IL uptake and the continuous phase of conducting PEO domains.The relationship between ionic conductivity and temperature fits the Vogel-Tamman-Fulcher(VTF)equation.In addition,the electrolyte films are flame retardant owing to the addition of IL.The polymer electrolytes with good safety and high ambient-temperature ionic conductivity developed in this work are potentially useful in solid lithium-ion batteries.