PEO基纳米复合聚合物电解质电化学性质的研究

以PEO8 LiClO4作母体,纳米SiO2为填料,制成PEO8 LiClO4 SiO2(x%)系列复合聚合物电解质,测定这该电解质的电导率、锂离子迁移数和电化学稳定窗口,并对其晶态结构作差热分析表征.结果表明,纳米SiO2的引入,显著提高了电解质的电导率,在22℃时达到4.3×10-5S·cm-1.此外,还探讨了填料对复合聚合物电解质电导率提高的影响机理.     

表面改性纳米SiO2复合聚合物电解质的制备及性能

通过化学方法将具有增塑效果的环状碳酸酯基团引入纳米SiO2表面,并用FTIR与TGA对改性纳米SiO2进行了表征.将改性纳米SiO2添加到以聚氧化乙烯(PEO)为基体的聚合物电解质中,制备了复合聚合物电解质.通过DSC和交流阻抗等方法对该聚合物电解质膜的热力学和电化学性能进行了研究.结果表明,掺杂改性纳米SiO2的聚合物电解质具有更高的离子电导率,室温最高离子电导率可达到1.84×10-5 S/cm;具有较高的锂离子迁移数,最高可达到0.49,且具有更好的界面稳定性.     

碱性纳米复合聚合物电解质研究

为了提高聚氧化乙烯(PEO)/KOH 基碱性聚合物电解质的电导率, 制电解质膜时分别将纳米 TiO2、纳米β-Al2O3和纳米 SiO2添加到 PEO/KOH 体系中, 制备出了兼顾电学和力学性能的碱性纳米复合聚合物电解质. 交流阻抗测试显示, 其室温(28 ℃)电导率可达到 10-3 S?cm-1数量级. 循环伏安研究表明, 制得的电解质膜在不锈钢惰性电极上的电化学稳定窗口约为 1.6 V. 分别研究了聚合物电解质膜中 KOH, H2O, 无机纳米粉末的含量以及温度对体系电导率的影响.     

纳米阻燃氢氧化镁/聚氧化乙烯复合聚合物电解质

合成了纳米氢氧化镁作为聚氧化乙烯(PEO)基聚合物电解质的增塑剂和阻燃剂,并对其进行X射线衍射(XRD)、透射电子显微镜(TEM)和热重(TG)分析研究.制得的氢氧化镁为片状六方晶体,尺寸在50-80nm之间,纳米氢氧化镁在340℃时开始热分解.对纳米氢氧化镁/PEO复合聚合物电解质的电化学研究结果显示:纳米氢氧化镁/PEO复合聚合物电解质的离子电导率随着添加纳米氢氧化镁的质量分数的增加先增大后减小,其在5%-10%之间时,复合聚合物电解质的离子电导率达到最大值.纳米氢氧化镁的添加使复合聚合物电解质的阳极氧化电位有一定程度的提高,纳米氢氧化镁具有改善PEO阳极抗氧化能力的作用.     

纳米SiO_2复合的梳状聚醚聚合物电解质的导电性能研究

于含锂盐的梳状聚醚聚合物电解质添加纳米S iO2制备复合聚合物电解质.并分别使用DSC和XRD研究S iO2对聚合物链段运动能力的影响.电导率测试表明,在相同的锂盐浓度下,加入5%的纳米S iO2后,聚合物电解质具有最高的离子电导率,30℃时为7.8×10-5S/cm,80℃时达到4.5×10-4S/cm.与未添加S iO2的聚合物电解质相比,电导率提高了30%~60%.TGA测定给出该聚合物的热分解温度为300℃左右,显示出良好的安全性能.     

用于聚合物镍氢电池的新型PVA/SiO2碱性微孔聚合物电解质（英文）

采用溶胶凝胶法,结合相转移法和碱液活化法制备了PVA/SiO2碱性微孔聚合物电解质,通过SEM、XRD、交流阻抗法和循环伏安法表征了电解质的结构与电化学性能.研究表明,PVA/5ωSiO2(ω为质量分数)共混膜上的微孔大小合适,聚合物电解质的离子电导率最大可达1.62×10-2 S cm-1,电化学稳定窗口2 V以上;将PVA/SiO2碱性微孔电解质组装成聚合物镁基镍氢电池,与传统镍氢电池相比,循环稳定性大大增加.     

用于聚合物镍氢电池的新型PVA/SiO2碱性微孔聚合物电解质

采用溶胶凝胶法,结合相转移法和碱液活化法制备了PVA/SiO2碱性微孔聚合物电解质,通过SEM、XRD、交流阻抗法和循环伏安法表征了电解质的结构与电化学性能.研究表明,PVA/5ωSiO2(ω为质量分数)共混膜上的微孔大小合适,聚合物电解质的离子电导率最大可达1.62×10-2 S·cm-1,电化学稳定窗口2V以上;将PVA/SiO2碱性微孔电解质组装成聚合物镁基镍氢电池,与传统镍氢电池相比,循环稳定性大大增加.     

MCM-41介孔分子筛掺杂的微孔型聚合物电解质的制备与表征

以介孔分子筛MCM-41作填料,丙酮与二甲基甲酰胺混合液为溶剂,用直接造孔成膜的方法制备了微孔型聚合物电解质膜.该法避免使用造孔增塑剂,既简化了制膜工序,又减少电池中副反应的发生,使电池性能得以提高.MCM-41分子筛具有六方有序排列的单一柱状孔道结构和纳米级的粒子尺度,其骨架结构单元与一般聚合物电解质常用的纳米SiO2填料具有相同的化学成分,该分子筛堆积时形成的表面空隙及其独有的一维介孔孔道对聚合物电解质微孔的形成与连通、电导率的提高都具有重要作用,是一种极具实用价值的新型无机填料.     

聚合物/TiO2杂化纳米纤维微孔膜的制备及其在染料敏化太阳能电池中的应用

利用静电纺丝技术,制备了不同的聚合物/TiO2杂化纳米纤维微孔膜,吸附液体电解质后形成聚合物/TiO2杂化纳米纤维微孔膜准固态电解质,应用于制备准固态染料敏化太阳能电池(DSSCs).测试了电纺聚合物纳米纤维微孔膜电解质的吸液率、孔隙率、离子电导率等参数,研究了纳米纤维微孔膜准固态电解质DSSCs的光伏性能.结果显示,TiO2的掺入可提高聚合物/TiO2杂化纳米纤维微孔膜对液态电解质的浸润扩散性能,从而提高纳米纤维微孔膜对液态电解质的吸附能力.组装的DSSCs的光电转换效率可达液态电解质的90%以上,并具有较好的长期工作稳定性.     

TiO_2/SiO_2纳米薄膜的光催化活性和亲水性

通过 sol-gel工艺在钠钙玻璃表面制备了均匀透明的 TiO2/SiO2复合纳米薄膜 .实验结果表明 : 当 SiO2添加量较高时 , TiO2/SiO2复合纳米薄膜的光催化活性明显降低 ;当 SiO2添加量较低时 ,TiO2/SiO2复合薄膜的光催化活性无明显变化 .在 TiO2薄膜中添加 SiO2,可以抑制薄膜中 TiO2晶粒的长大 ,同时薄膜表面的羟基含量增加 , 水在复合薄膜表面的润湿角下降 , 亲水能力增强 .当 SiO2含量为 10％－ 20％（摩尔分数）时获得了润湿角为 0°的超亲水性薄膜 .     

Effect of nanoscale CeO<Subscript>2</Subscript> on PVDF-HFP-based nanocomposite porous polymer electrolytes for Li-ion batteries

New poly (vinylidenefluoride-co-hexafluoro propylene) (PVDF-HFP)/CeO₂-based microcomposite porous polymer membranes (MCPPM) and nanocomposite porous polymer membranes (NCPPM) were prepared by phase inversion technique using N-methyl 2-pyrrolidone (NMP) as a solvent and deionized water as a nonsolvent. Phase inversion occurred on the MCPPM/NCPPM when it is treated by deionized water (nonsolvent). Microcomposite porous polymer electrolytes (MCPPE) and nanocomposite porous polymer electrolytes (NCPPE) were obtained from their composite porous polymer membranes when immersed in 1.0 M LiClO₄ in a mixture of ethylene carbonate/dimethyl carbonate (EC/DMC) (v/v = 1:1) electrolyte solution. The structure and porous morphology of both composite porous polymer membranes was examined by scanning electron microscope (SEM) analysis. Thermal behavior of both MCPPM/NCPPM was investigated from DSC analysis. Optimized filler (8 wt% CeO₂) added to the NCPPM increases the porosity (72%) than MCPPM (59%). The results showed that the NCPPE has high electrolyte solution uptake (150%) and maximum ionic conductivity value of 2.47 × 10⁻³ S cm⁻¹ at room temperature. The NCPPE (8 wt% CeO₂) between the lithium metal electrodes were found to have low interfacial resistance (760 Ω cm²) and wide electrochemical stability up to 4.7 V (vs Li/Li⁺) investigated by impedance spectra and linear sweep voltammetry (LSV), respectively. A prototype battery, which consists of NCPPE between the graphite anode and LiCoO₂ cathode, proves good cycling performance at a discharge rate of C/2 for Li-ion polymer batteries.     

Cross-linking copolymers of acrylates’ gel electrolytes with high conductivity for lithium-ion batteries

The cross-linking gel copolymer electrolytes containing alkyl acrylates, triethylene glycol dimethacrylate, and liquid electrolyte were prepared by in situ thermal polymerization. The gel polymer electrolytes containing 15 wt% polymer content and 85 wt% liquid electrolyte content with sufficient mechanical strength showed the high ionic conductivity around 5?×?10^?3 Scm^?1 at room temperature. The gel electrolytes containing different polymer matrices were prepared, and their physical observation and conductivity were discussed carefully. The cross-linking copolymer gel electrolytes of alkyl acrylates with other monomers were designed and synthesized. The results showed that copolymerization can improve the mechanical properties and ionic conductivities of the gel electrolytes. The polymer matrices of gels had excellent thermal stability and electrochemical stability. The scanning electron microscope analysis showed the gel electrolyte was the homogeneous structure, and the cross-linking polymer host was the porous three-dimensional network structure, which demonstrated the high conductivity of the gel electrolytes. The gel polymer Li-ion battery was prepared by this in situ thermal polymerization. The cell exhibited high charge-discharge efficiency at 0.1 C. The results of LiFePO4-PEA-Li cell and graphite-PEA-Li cell showed that gel polymer electrolytes have good compatibility with the battery electrodes materials.     

层层纳米自组装锆基色谱填料的表面性质研究

硅胶具备了许多色谱载体应具有的合适的表面物理化学参数.但硅基填料可使用的pH值范围较窄及其表面裸露的硅羟基对碱性物质和含N生物大分子的不可逆吸附等缺点限制了其在一些重要领域中的应用.氧化锆由于其优异的化学稳定性,特别是对碱性化合物和生物大分子的分离适应性而在色谱应用方面受到极大的关注[1,2],极有可能成为通用的色谱基质填料之一[3].本文旨在制备具有良好表面性质的锆基色谱填料,结合硅胶和氧化锆的优点,采用层层纳米自组装方法(LbL)[4]在微米硅胶球模板表面包覆多层纳米氧化锆颗粒,制备了新型氧化锆基质填料ZrO2/SiO2,…     

Novel ferrocene-containing amphiphilic block copolymer nanoparticles as high-capacity charge carriers in aqueous redox flow systems

Size-exclusion polymer electrolytes are promising charge carriers to diminish the crossover and allowing commercially available low-cost porous membranes in redox flow batteries. Boosting the solubility in water and maximizing the number of redox sites to enhance the capacity of these polymeric systems is challenging. New highly water dispersed amphiphilic diblock copolymers are reported here, with an average concentration value of 1.7 10^?3 mmol of Ferrocene (Fc)-linked moieties per mg of polymer, determined by total X-ray reflection fluorescence. These redox amphiphilic block copolymers are stabilized in water as spherical nanoparticles (20 nm) by using a simple phase solvent inversion procedure. We evidence a maximum polymer dispersibility value of 6 g/L in water, for long-term stable polymer nanoparticle suspensions, yielding a theoretical capacity value of 4.78 mAh at 10.5 mM Fc. Further adjustment of the ionic conductivity and pH of these stable redox block copolymer suspensions has rendered a conductivity value of 44.5 mS/cm at pH values close to a neutral one, by adding a variety of salt supports. Studies using a 3-electrode configuration cell reveal an efficient charge transport between each of the Fc motifs in the polymer nanoparticle. A capacity value of 3.1 mAh with no transient of the polymer nanoparticles crosswise the cheap porous membrane is evidenced when cycled as polycatholyte material in a Zn hybrid aqueous redox flow battery. The particle size and electronic changes of these novel amphiphilic redox block copolymer electrolytes during consecutive redox cycles have also been monitored by dynamic light scattering and ultraviolet-visible spectroscopy, respectively. The analysis of the results enables the understanding of the main mechanisms behind their non-fully reversible capacity. Among them, aggregation and sedimentation, along with retention inside the graphite felt electrode acting the latter as a filter. These insights will aid the design of future polymer electrolyte materials and redox flow battery components with better performance and cost.     

Porous Cyclodextrin Polymer Enables Dendrite-Free and Ultra-Long Life Solid-State Zn-I2 Batteries

Zn-I₂ batteries have attracted attention due to their low cost, safety, and environmental friendliness. However, their performance is still limited by the irreversible growth of Zn dendrites, hydrogen evolution reactions, corrosion, and shuttle effect of polyiodide. In this work, we have prepared a new porous polymer (CD-Si) by nucleophilic reaction of β-cyclodextrin with SiCl₄, and CD-Si is applied to the solid polymer electrolyte (denoted PEO/PVDF/CD-Si) to solve above-mentioned problems. Through the anchoring of the CD-Si, a conductive network with dual transmission channels was successfully constructed. Due to the non-covalent anchoring effect, the ionic conductivity of the solid polymer electrolytes (SPE) can reach 1.64×10⁻³ S cm⁻¹ at 25 °C. The assembled symmetrical batteries can achieve highly reversible dendrite-free galvanizing/stripping (stable cycling for 7500 h at 5 mA cm⁻² and 1200 h at 20 mA cm⁻²). The solid-state Zn-I₂ battery shows an ultra-long life of over 35,000 cycles at 2 A g⁻¹. Molecular dynamics simulations are performed to elucidate the working mechanism of CD-Si in the polymer matrix. This work provides a novel strategy towards solid electrolytes for Zn-I₂ batteries.     

Nano-encapsulation of LiCoO2 cathodes by a novel polymer electrolyte and its influence on thermal safeties of Li-ion batteries

A new approach enabling the target control of exothermic reaction between delithiated LiCoO₂ and liquid electrolytes has been presented, which is based on the nano-encapsulation of LiCoO₂ by cPVA (cyanoethyl polyvinylalcohol)-based gel polymer electrolytes. This novel morphology and the possible formation of coordinated complexes between the cyano (–CN) groups of cPVA and the cobalt cations of LiCoO₂ are considered as key factors to significantly suppress the exothermic reaction in the delithiated LiCoO₂. Such an improved thermal stability of the cPVA-modified LiCoO₂ has led to a noticeable achievement in the hot-oven safety behavior of cells. Meanwhile, it was observed that both the excellent ionic conductivity of cPVA-based gel polymer electrolytes and the well-preserved porous structure of modified cathodes contribute to the satisfactory C-rate capability and the cyclability of cells.     

硅氧烷基聚合物电解质*

聚合物锂离子电池的核心技术是研制高离子传导率、适宜机械性能以及化学和电化学性能稳定的聚合物电解质材料。在众多寻求高性能聚合物电解质的研究工作中,由于硅氧烷基聚合物电解质具有灵活多样的分子结构设计、易于合成实施、优异的电化学性能和室温电导率等特点,一直是人们关注的热点领域。本文综述了近年来新型硅氧烷基聚合物电解质的设计与合成的研究工作,重点介绍了采用聚硅氧烷嵌段、接枝聚合物通过共混、互穿网络结构、交联网络结构以及无机-有机复合等方法开展的相关聚合物电解质的研究工作。同时也介绍了聚硅氧烷电解质的研究方法和基于聚硅氧烷电解质的应用研究进展。     

Effect of surface area and heteroatom of porous carbon materials on electrochemical capacitance in aqueous and organic electrolytes

A series of porous carbon materials with wide range of specific surface areas and different heteroatom contents had been prepared using polyaniline as carbon precursor and KOH as an activating agent. Effect of surface area and heteroatom of porous carbon materials on specific capacitance was investigated thoroughly in two typical aqueous KOH and organic 1-butyl-3- methylimidazolium tetrafluoroborate/acetonitirle electrolytes. The different trends of capacitance performance were observed in these two electrolytes. Electrochemical analyses suggested that the presence of faradaic interactions on heteroatom-enriched carbon materials in organic environment is less significant than that observed in aqueous electrolytes. Thus, in aqueous electrolyte, a balance between surface area and heteroatom content of activated porous carbon would be found to develop a supercapacitor with high energy density. In organic electrolyte, the capacitance performance of porous carbon is strongly dependent on the surface area. The results may be useful for the design of porous carbon-based supercapacitor with the desired capacitive performance in aqueous and organic electrolytes.     

P(VAc-MMA)为基体的聚合物电解质研究

以醋酸乙烯酯(VAc)和甲基丙烯酸甲酯(MMA)为单体, 采用半连续种子乳液聚合法制备了无规共聚物聚(醋酸乙烯酯-甲基丙烯酸甲酯)[P(VAc-MMA)], 并以此聚合物为基体制备了聚合物电解质. 用红外光谱(FTIR)、核磁共振氢谱(¹H NMR)、扫描电镜(SEM)、差热/热重分析(DSC/TG)、X射线衍射(XRD)、机械性能测试和电化学交流阻抗等方法对聚合物和聚合物电解质的性质进行了研究. 测试结果表明: VAc和MMA聚合生成P(VAc-MMA); 聚合物膜含有大量微孔结构, 利于离子传输; 聚合物电解质膜具有优良的热稳定性和机械强度; 25 ℃下, 最高的离子电导率达到了1.27× 10^－3 S•cm^－1; 离子电导率随着温度的升高而迅速增加, 电导率-温度曲线符合Arrhenius方程.