纳米贵金属插入的粘土用于催化选择性加氢反应

 The use of clay minerals in the synthesis of nanosized noble metal particles to give increased catalytic activity was investigated. Nanosized platinum and ruthenium catalysts intercalated in clay (montmorillonite/hectorite) were synthesised and their catalytic activity was evaluated for the selective hydrogenation of three different α,β-unsaturated aldehydes, namely, crotonaldehyde, cinnamaldehyde, and citral, in a gas phase microreactor. The metal nano-sol was prepared by the chemical reduction of its precursor by the micellar technique in the presence of cetyl trimethyl ammonium bromide (CTAB), and the micelle stabilized metal particles were intercalated in the clay mineral by ion exchange. TEM micrographs of the catalyst particles showed that the metal particles were in the nanometre range. The average diameters of the particles were 1–25 nm. The effects of temperature, metal loading, and hydrogen flow rate on the catalytic activity and selectivity for α,β- unsaturated alcohol were studied. The results were correlated with the structural properties of the catalysts. The products formed in each reaction over the different catalysts showed that the catalysts were very active for hydrogenation, and the selectivity for the desired product, namely, α,β-unsaturated alcohol, was good. The metal catalysts intercalated in montmorillonite showed better selectivity than that in hectorite because of its higher acidity. Increased selectivity for α,β-unsaturated alcohol was observed with increased flow rate of hydrogen.     

Cu/ZrO2催化剂上乙醇水蒸气重整反应的研究: Ⅱ 反应条件的影响

采用沉淀法或醇凝胶法、浸渍法制备Cu/ZrO2催化剂，在常压微型固定床石英管反应器上进行乙醇水蒸气重整反应，采用程序升温还原（TPR）技术表征催化剂的还原特性。考察了催化剂还原温度、反应温度、水醇比、空速等对反应的影响以及催化剂的稳定性。结果表明，在300℃～500℃，随反应温度升高，乙醇转化率增大，H2选择性下降。不同还原温度对转化率的影响不是很大，对于H2选择性，300℃、400℃还原的催化剂优于500℃还原的催化剂。高水醇比有利于提高转化率和H2选择性。随空速增大，转化率和H2选择性呈现下降的趋势。8%Cu/ZrO2催化剂在400℃或450℃反应22h显示出良好的稳定性。     

膜反应器中Ni-Cu催化剂上CO加氢合成乙烯的研究

 将硅藻土－TiO2－聚乙烯（或聚丙烯）疏水复合膜反应器应用于\r\nCO加氢合成乙烯的反应过程，以Ni－Cu／TiSiO和Ni－Cu／MgSiO为催化\r\n剂，考察了反应温度、空速和进料组成等因素对CO转化率和乙烯选择性\r\n的影响．结果表明：膜催化反应的产物与常规催化反应相同，催化反应\r\n机理没有区别，在适宜条件下，膜催化反应的CO转化率和乙烯选择性较\r\n之常规催化反应提高了10％左右，二氧化碳和甲烷的选择性降低，而乙\r\n烷的选择性略有增加．     

木质素降解模型化合物愈创木酚及苯酚原位加氢制备环己醇

以Raney Ni为催化剂,研究了甲醇水相重整制氢与木质素降解模型化合物愈创木酚／苯酚加氢的耦合反应.考察了反应前冷压、反应温度、反应时间、物料配比等条件对木质素降解模型化合物原位加氢反应性能的影响,并对影响机制进行了讨论.结果表明,在反应温度为220 ℃、反应前冷压0 MPa(表压)、物料比水／甲醇／模型化合物为20∶5∶0.8的条件下,反应7 h后愈创木酚转化率与环己醇选择性分别达99.00％和93.74％,反应12 h后苯酚的转化率与环己醇选择性分别达90.50％和99.29％.采用原位加氢反应,木质素降解的酚类模型化合物转化率和选择性明显优于外部供氢反应的转化率和选择性,同时,避免了外部供氢反应存在的氢气制备、储存、传输及加氢条件苛刻等问题,为木质素解聚产物制备化工品提供了新思路与实验基础.     

Aqueous-phase catalytic hydrogenation of furfural to cyclopentanol over Cu-Mg-Al hydrotalcites derived catalysts: Model reaction for upgrading of bio-oil

A series of Cu-Mg-Al hydrotalcites derived oxides with a (Cu+Mg)/Al mole ratio of 3 and varied Cu/Mg mole ratio (from 0.07 to 0.30) were prepared by co-precipitation and calcination methods, then they were introduced to the hydrogenation of furfural in aqueous-phase. Effects of Cu/Mg mole ratio, reaction temperature, initial hydrogen pressure, reaction time and catalyst amount on the conversion rate of furfural as well as the selectivity toward desired product cyclopentanol were systematically investigated. The conversion of furfural over calcined hydrotalcite catalyst with a Cu/Mg mole ratio of 0.2 was up to 98.5% when the reaction was carried out under 140 °C and the initial hydrogen pressure of 4 MPa for 10 h, while the selectivity toward cyclopentanol was up to 94.8%. The catalysts were characterized by XRD and SEM. XRD diffraction of all the samples showed characteristic pattern of hydrotalcite with varied peak intensity as a result of different Cu content. The catalytic activity was improved gradually with the increase of Cu component in the hydrotalcite.     

甲醇水蒸气重整制氢Cu/ZnO/Al2O3催化剂的研究

燃料电池作为一种无污染、高效率的能源引起世界各大汽车公司的广泛关注[1,2]。用于燃料电池的燃料目前研究较多的是氢气,用氢气作燃料存在储存、安全、运输等问题,寻求合适贮氢方法或替代燃料,实现车载制氢是解决问题的办法。甲醇作为液体燃料,因具有高能量密度,低碳含量,以及运输和贮存等优势成为车载制氢的理想燃料,甲醇水蒸气重整制氢反应也成为研究的热点[3～10]。车载制氢对甲醇水蒸气重整制氢反应体系中的产氢速率,氢气和CO的含量都有一定的要求。尤其对CO含量要求更为苛刻,因CO易引起燃料电池阳极催化剂中毒[11,12]。因此,开…     

Kinetics of hydrogen production of methanol reformation using Cu/ZnO/Al2O3 catalyst

The catalytic performance of methanol reformation using Cu/ZnO/Al2O3 was investigated at low temperature. The operation conditions, such as composition of Cu, Zn, and Al, temperature, molar ratio of H2O/CH3OH, weight hourly space velocity, catalyst weight, and kind and flow rate of carrier gas (helium and air), were evaluated to obtain the optimum reaction condition. The catalysts were prepared by oxalic coprecipitation, coprecipitation, and polyol method. The weight composition of Cu, Zn, and Al prepared by oxalic coprecipitation was 15:15:5 by high-throughput screening of combinatorial chemistry method, which was the best Cu/ZnO/Al2O3 catalyst. The prepared catalysts showed high activity and selectivity towards hydrogen formation. The methanol conversion, production rate, and volumetric percentage of hydrogen using this best catalyst were larger than 95%, 0.65 mol/h x g and 59%, respectively, and the CO volumetric percentage was smaller than 0.22% when the reaction temperature was 240 degrees C. The size and dispersity of copper, and the activity and turnover frequency of the catalyst were calculated as well.     

Mn-Al和Cu-Mn-Al复合氧化物催化苯甲醇选择氧化反应

用溶胶-凝胶法制备了不同组成的Mn-Al和Cu-Mn-Al复合氧化物两组催化剂,用于苯甲醇选择氧化反应.用X射线衍射(XRD)、N2物理吸附(BET)、扫描电镜(SEM)、H_2程序升温还原(H_2-TPR)、O_2程序升温脱附(O_2-TPD)和X射线光电子能谱(XPS)技术对催化剂进行了结构表征,考察了催化剂组成对催化活性的影响.结果表明:以甲苯为溶剂,O_2为氧化剂,353 K反应5 h,Mn_2Al和Cu_(0.3)Mn_(0.7)Al_2催化剂上的苯甲醇转化率分别为36.6%和40.9%,苯甲醛选择性均为100%.进一步研究表明:催化剂活性与其H2还原性和O_2吸附性有关,高活性的催化剂吸附氧多,生成的活性氧易参与反应.     

Bimetallic Co–Ni/TiO<Subscript>2</Subscript> catalysts for selective hydrogenation of cinnamaldehyde

Bimetallic Co–Ni catalysts in the composition range Co_(1?x)Ni_x with x?=?0.0, 0.2, 0.3, 0.4, 0.5, 0.6, 0.8 and 1.0, with total metal loading of 15% w/w and supported on TiO₂-P25, have been prepared by chemical reduction of the metal acetates by glucose in aqueous alkaline medium and characterized by XRD, TEM, TPR, XPS and H₂-TPD techniques. Selective hydrogenation of cinnamaldhyde (CAL) to hydrocinnamaldehyde (HCAL), cinnamyl alcohol (COL) and hydrocinnamyl alcohol (HCOL) has been investigated at 20 bar pressure, in the temperature range 120–140 °C. Co/Ni crystallite sizes in the range 6.0?±?1 nm are observed by TEM. TPR and XPS results indicate the formation of nanoscale Co–Ni alloys, which tend to weaken M–H bond strength, as revealed by H₂-TPD measurements. Ni/TiO₂ displays very high conversion of CAL (86.9%) with high selectivity (78.7%) towards HCAL formation at 140 °C. Co/TiO₂, on the other hand, exhibits relatively lower CAL conversion (55%) and higher selectivity (61.3%) for COL formation at the same temperature. However, bi-metallic Co–Ni catalysts in the composition range x?=?0.3–0.6 display very high conversion (>?98%) due to alloy formation and weakening of M–H bonds. Bimetallic Co_0.7Ni_0.3 catalyst displays high conversion of CAL (98.1%) and high selectivity (82.9%) towards HCOL. Overall CAL hydrogenation activity at 140 °C, when expressed as TOF, displays a maximum value at the composition Co_0.5Ni_0.5. Activity and selectivity patterns have been rationalized based on the reaction pathways observed on the catalysts and the influence of Co–Ni alloy formation and M–H bond strength. Thus, a synergetic effect, originating from an appropriate composition of base metal catalysts and reaction conditions, could result in hydrogenation activity comparable with noble metal based catalysts.     

Ni-Fe/蒙脱土催化剂催化乙醇水蒸气重整制氢的研究

采用浸渍法制备了一系列Ni-Fe/蒙脱土(MMT)催化剂,并应用于乙醇水蒸气重整制氢反应(ESR)。采用X射线衍射(XRD)、N_2吸附脱附分析和H_2-程序升温还原(H_2-TPR)表征手段对催化剂的物理化学性质、还原性能、碳沉积等进行了研究。结果表明,Ni-Fe/MMT催化剂中,Ni、Fe高度分散在载体MMT层间及表面,而且Fe的加入降低了Ni颗粒的粒径,增强了Ni~(2+)与载体的相互作用力。以10Ni5Fe/MMT为催化剂,在反应温度为500℃、水醇比为3∶1、空速为12 h~(-1),反应进行30 h后,乙醇转化率为100%,氢气选择性仍保持72%,副产物CO和CH_4含量明显降低。这是因为催化助剂Fe的引入,一方面,提高了Ni的分散度,使得ESR低温活性较好;另一方面,减小了Ni颗粒粒径,小颗粒的Ni有利于抑制甲烷的生成,并且Fe的加入加强了甲烷重整和水煤气变换反应,提高产物中氢气的选择性。     

焙烧温度对CuMgAl催化剂催化糠醛气相加氢制糠醇性能的影响

采用分步沉淀过程制得质量比m(CuO)∶m(MgO)∶m(Al_2O_3)为25∶26∶49的CuMgAl类水滑石前驱体,经过不同温度焙烧制得CuMgAl-t催化剂。通过BET、热重、XRD、H_2-TPR和CO_2-TPD对催化剂进行表征,在固定床中考察CuMgAl-t催化剂催化糠醛气相加氢制糠醇的性能。结果表明,焙烧温度影响催化剂活性、稳定性及对产物的选择性,低温焙烧的催化剂经还原后可获得较多活性中心,高温焙烧的催化剂表面具有更多的碱性位,CuMgAl催化剂经450℃焙烧表面存在适宜的活性中心和碱性位。在常压、反应温度180℃、氢醛物质的量比5∶1、糠醛体积空速0.3h~(-1)的条件下,CuMgAl-450催化剂上糠醛的转化率和糠醇的选择性分别达到98.64%和97.66%。     

磷酸铈对磷化镍催化苯酚转移加氢的促进作用

通过氢气原位程序升温还原法制备了一系列不同Ce/Ni摩尔比的CePO₄-Ni₃P及Ni₃P催化剂, 考察了其在苯酚催化转移加氢反应的催化性能. 研究了Ce/Ni摩尔比、 供氢溶剂、 反应温度和反应时间对催化剂性能的影响, 并初步考察了苯酚转移加氢的反应动力学. 研究结果表明, CePO₄的加入能显著提升体相Ni₃P催化苯酚转移加氢的转化率, 且Ce/Ni摩尔比为0.2时促进作用最显著; 在所考察的供氢溶剂中异丙醇展现出最好的性能; 使用CePO₄(0.2)-Ni₃P作为反应催化剂, 异丙醇作为供氢溶剂, 220 ℃下反应6 h, 苯酚转化率和环己醇选择性分别可达93.1%和92.0%.     

还原剂对Au-Pd/CeO2催化剂甲醇部分氧化性能的影响

以PVP为保护剂,乙醇(ER)、乙二醇(GR)和水合肼(HR)为还原剂制备了一系列Au-Pd/CeO2催化剂,考察了还原剂对甲醇部分氧化性能的影响,并运用XRD、TPD和TPR等手段对催化剂进行了表征。结果表明,Au-Pd/CeO2(ER)催化剂具有较大的比表面积,形成的AuxPdy量较多、粒径较小、分散度较高、活性组分与载体的相互作用较强,同时对甲醇的吸附量较大和吸附温度较低。因此,该催化剂具有较高的催化活性和氢气选择性以及较低的CO质量分数。     

Influence of alkali metal doping on surface properties and catalytic activity/selectivity of CaO catalysts in oxidative coupling of methane

Surface properties （viz. surface area, basicity/base strength distribution, and crystal phases） of alkali metal doped CaO （alkali metal/Ca= 0.1 and 0.4） catalysts and their catalytic activity/selectivity in oxidative coupling of methane （OCM） to higher hydrocarbons at different reaction conditions （viz. temperature, 700 and 750 ℃; CH4/O2 ratio, 4.0 and 8.0 and space velocity, 5140-20550 cm^3 ·g^-1·h^-1） have been investigated. The influence of catalyst calcination temperature on the activity/selectivity has also been investigated. The surface properties （viz. surface area, basicity/base strength distribution） and catalytic activity/selectivity of the alkali metal doped CaO catalysts are strongly influenced by the alkali metal promoter and its concentration in the alkali metal doped CaO catalysts. An addition of alkali metal promoter to CaO results in a large decrease in the surface area but a large increase in the surface basicity （strong basic sites） and the C2＋ selectivity and yield of the catalysts in the OCM process. The activity and selectivity are strongly influenced by the catalyst calcination temperature. No direct relationship between surface basicity and catalytic activity/selectivity has been observed. Among the alkali metal doped CaO catalysts, Na-CaO （Na/Ca = 0.1, before calcination） catalyst （calcined at 750 ℃）, showed best performance （C2＋ selectivity of 68.8% with 24.7% methane conversion）, whereas the poorest performance was shown by the Rb-CaO catalyst in the OCM process.     

Selective Hydrogenation of Diethyl Disulfide to Ethanethiol in the Presence of Sulfide Catalysts

The gas-phase reaction of diethyl disulfide hydrogenation at atmospheric pressure in the presence of supported transition metal sulfides was studied. The reaction of diethyl disulfide with hydrogen at T = 200°C resulted in ethanethiol, and the selectivity to ethanethiol was no lower than 94%. The selectivity decreased at a higher temperature because of diethyl disulfide decomposition to ethylene and hydrogen sulfide. The reaction of diethyl disulfide in the presence of hydrogen occurred at a higher rate and selectivity than that in an atmosphere of helium. The activity of metal sulfides supported on aluminum oxide was higher than on the other studied supports—aluminosilicate, silica gel, and a carbon support. Metal sulfides supported on Al₂O₃ were arranged in the following order according to their activity: Rh > Ru > Mo Pd > Ni > W. Bimetallic catalysts were less active than monometallic catalysts. The activity of catalysts increased with the sulfide sulfur content; the partial reduction of metal sulfides also increased the catalytic activity.     

氧化铝担载的贵金属铱基催化剂的制备及其对甲醇裂解反应的催化性能

 以ZrO2, La2O3或MgO为助剂制备了氧化铝担载型铱基催化剂,考察了其对甲醇裂解反应的催化性能,并用X射线光电子能谱、程序升温还原、 H2程序升温脱附和CO程序升温脱附等技术对催化剂进行了表征. 结果表明, ZrO2, La2O3和MgO助剂的引入均能提高主产物氢气和CO的选择性. ZrO2是甲醇裂解反应的优良助剂,可以显著提高甲醇的转化率和氢气的收率. 氧化铝担载型贵金属铱基催化剂上存在强的氢溢流现象,这使催化剂具有良好的反应性能,同时有利于产物的脱附,氧化物助剂的加入能够进一步促进氢的溢流.     

微波辅助的金属氯化物Lewis酸催化纤维素水解

研究了微波辐射下四种金属氯化物Lewis酸的催化纤维素酸水解反应性能,发现CuCl₂的催化性能最好。反应温度、反应时间、微波功率、催化剂用量和酸种类对纤维素水解转化率、葡萄糖和5-羟甲基糠醛(5-HMF)的选择性均有明显影响。与传统热反应相比,微波辐射明显加快纤维素酸水解速率,提高葡萄糖的选择性。0.5g纤维素和15g水,在微波功率800W,温度到达225℃时立即停止反应的条件下,当CuCl₂用量为0.05mmol时,纤维素转化率和葡萄糖选择性达72.6%和62.3%;当CuCl₂用量为0.15mmol时,5-HMF的选择性最高为13.2%;当CuCl₂用量为0.30mmol时,纤维素的转化率高达90.6%,但葡萄糖选择性只有6.7%。     

Pd/C和Raney Ni催化剂的制备及其催化活性比较

制备了Pd/C和Raney Ni催化剂,其结构和性能经XRD,BET和SEM表征。并以呋喃加氢制备四氢呋喃为探针反应,对两种催化剂的催化活性进行了比较,探讨了反应温度、反应压力和催化剂用量对转化率和选择性的影响,结果表明:Raney Ni的催化活性优于Pd/C。     

复合氧化物负载的Ni基催化剂上愈创木酚加氢脱氧性能

分别以Al₂O₃-SiO₂,Al₂O₃-TiO₂,TiO₂-SiO₂和TiO₂-ZrO₂双金属氧化物为载体研究Ni基催化剂的愈创木酚加氢脱氧性能. 重点考察了催化剂载体、溶剂种类、反应温度和压力对愈创木酚转化率及产物选择性的影响,并对催化剂的抗积碳性能、重复利用性能和愈创木酚加氢脱氧反应机理进行了探讨. 通过BET（Brunauer-Emmett-Teller）比表面积、X射线衍射（XRD）、NH₃程序升温脱附（NH₃-TPD）和H₂程序升温还原（H₂-TPR）等表征手段对催化剂的比表面积、物相结构、表面酸性、可还原性能进行了表征. 结果表明,Ni/TiO₂-ZrO₂催化性能相对较优. 在300 ℃、初始氢压4 MPa、以十氢萘为溶剂的最佳反应条件下,愈创木酚的转化率为100%,环己烷选择性高达86.4%. 该催化剂还具有抗积碳性能,反应后的催化剂上仅检测到3.2%（质量分数）的积碳量.     

BiZrO_(x)/ZSM-5催化合成气直接芳构化的研究北大核心CSCD

使用超临界法制备纳米BiZrO_(x)金属氧化物与ZSM-5分子筛复合得到双功能催化剂用于合成气直接芳构化,研究了Bi/Zr比对BiZrO_(x)金属氧化物、BiZrO_(x)/ZSM-5双功能催化剂催化CO加氢反应性能的影响.结果表明,少量Bi掺杂在ZrO_(2)中显著促进了金属氧化物催化剂对H_(2)的吸附和解离,有利于合成气活化,同时有助于BiZrO_(x)金属氧化物表面获得高浓度和相对缺电子性的氧空位,提高了催化剂催化活性.合成气转化过程中,合成气转化能力与氧空位浓度呈正相关,Bi掺杂提高了CO的转化率和产物中芳烃的选择性.