二甲基亚砜在锂二次电池中的应用

采用二甲基亚砜(DMSO)作为锂二次电池的电解液, 研究了锂在DMSO中的沉积形貌和循环效率. 比较了六氟磷酸锂(LiPF₆)在DMSO、 碳酸丙烯酯(PC)和1,3-二氧环戊烷(DOL)3种溶剂中的沉积形貌和循环效率, 并研究了LiPF₆、 四氟硼酸锂(LiBF₄)、 高氯酸锂(LiClO₄)和二(三氟甲基磺酰)亚胺锂(LiTFSI)4种锂盐在DMSO中的沉积形貌和循环效率. 结果表明, 锂在DMSO中沉积得到的表面光滑平整且致密均匀, 循环效率在前10周要高于在PC中的, 溶剂DMSO有望用于金属锂二次电池中.     

亲锂电解液在LiNi0.6Mn0.2Co0.2O2／Li二次锂金属电池中的电化学性能

金属锂电池被认为是具有良好前景的下一代高能量密度电池。然而,传统的碳酸酯类电解液与锂的亲和性差,在循环过程中由于锂枝晶的生长和固体电解质膜（SEI）的不稳定导致金属锂电池性能快速衰减。采用1.2 mol／L六氟磷酸锂（LiPF₆）／二氟草酸硼酸锂（LiDFOB）／氟代碳酸乙烯酯（FEC）／碳酸二乙酯（DEC）,并添加了双三氟甲磺酰亚胺锂（LiTFSI）作为电解液,对其在LiNi_0.6Mn_0.2Co_0.2O₂／40 μm-Li（单位面积上负／正极材料的实际容量的比N／P＝2.85）电池中的电化学性能进行了研究。LiNi_0.6Mn_0.2Co_0.2O₂／40 μm-Li电池表现出优异的循环稳定性（循环120圈后,容量保持率>93%）和倍率性能（3C倍率下放电比容量为110 mA·h／g）。良好的电化学性能主要归因于该电解液可以在金属锂表面形成致密且稳定的SEI,并抑制锂枝晶的产生。     

高浓度锂盐电解液

基于1 mol ·dm^-3 LiPF₆/EC的传统非水型电解液已在锂离子电池中应用了20年。高功率、高比能锂离子电池以及锂金属电池（如Li-O₂和Li-S）的发展,对电解液提出了更高的要求,使得电解液的研究与开发到了一个革新换代的阶段。研究者们已经在离子液体、聚合物电解质和无机固态电解质等新型体系研究方面取得一定的研究成果,但是这些新体系存在的本征问题使其商业化应用面临一定的困难。研究者们也开始重新审视已优化的常规液态电解液体系,高浓度锂盐电解液（>3 mol ·dm^-3）再次引起广泛关注。本文综述了高浓度锂盐电解液的发展历程、溶液结构特征、分类标准及其特殊的物理化学性能、锂离子传输性质和电解液/电极相容性;对高浓度锂盐电解液存在的主要问题进行了简要分析,提出了相应的改进措施,展望了高浓度锂盐电解液未来的发展方向,为新型电解液的开发提供了一条新思路。     

一种双锂盐梳状聚合物电解质的制备及电化学性能

将聚乙二醇单甲醚(MPEG)接枝在聚(异丁烯-alt-马来酸酐)(PIAMA)上合成梳状锂单离子导体PIAMA-g-MPEG, 并与双(三氟甲基磺酰)亚胺锂(LiTFSI)复合制成双锂盐梳状聚合物电解质薄膜. 用核磁共振波谱 (¹H NMR)、 热重分析(TG)、 扫描电子显微镜(SEM)、 电化学阻抗(EIS)和电池充放电测试等方法对聚合物基体和电解质的物化性质和电化学性能进行了研究.结果表明, 设计的双锂盐梳状聚合物电解质能够有效解离并传输锂离子, 70 ℃下离子迁移数(t_Li⁺)为0.32, 离子电导率(σ)为1.5×10^-4 S/cm, 电化学稳定窗口为0~4.9 V (vs. Li/Li⁺). 组装Li|PIAMA-g-MPEG|Li电池并进行70 ℃恒电流充放电电压极化测试, 结果表明, 电解质与金属锂负极兼容性较好, 能够有效抑制锂枝晶的生长.组装LiFePO₄|PIAMA-g-MPEG|Li电池进行70 ℃长循环及倍率性能测试, 电解质表现出了优异的高温性能.     

以二甲亚砜水溶液为反应介质低温合成纳米级磷酸亚铁锂

采用二甲亚砜水溶液为反应介质, 在常压和108 ℃条件下, 经短时间的液相反应直接制备出橄榄石结构的纳米级LiFePO₄. IR分析表明, 液相法直接制得的LiFePO₄晶体结构中含有少量的Fe^3＋. 将液相直接制备的样品与少量葡萄糖混合后在600 ℃下焙烧3 h得到类球形的LiFePO₄/C材料. 电化学测试结果表明, 这种纳米级LiFePO₄/C材料在0.2 C 倍率下放电容量达到157.2 mAh/g, 并且具有较好的放电平台. 5 C和10 C放电容量仍能达到126.1和103.4 mAh/g, 且循环200次后容量没有明显衰减, 表现出优异的倍率放电特性和循环性能.     

新型导电盐(三氟甲基磺酰)(三氟乙氧基磺酰)亚胺锂及其非水电解液的制备与性能

制备了一种新型含氟磺酰亚胺锂盐(三氟甲基磺酰)(三氟乙氧基磺酰)亚胺锂{Li[(CF₃SO₂)·(CF₃CH₂OSO₂)N], Li[TFO-TFSI]}及其与碳酸乙烯酯(EC)/碳酸甲乙酯(EMC)混合溶剂(3∶7, 体积比)组成的非水电解液. 采用核磁共振波谱(NMR)、 红外光谱(IR)、 质谱(MS)、 元素分析(EA)和离子色谱(IC)等手段对合成锂盐Li[TFO-TFSI]进行了结构表征及纯度分析. 通过差示量热扫描(DSC)和热重分析(TG)对Li[TFO-TFSI]及其电解液1.0 mol/L Li[TFO-TFSI]-EC/EMC(3∶ 7)的热学性质进行了表征. 采用交流阻抗(EIS)、 循环伏安(CV)、 计时安培法及扫描电子显微镜(SEM)等对Li[TFO-TFSI]/碳酸酯电解液的基础物化和电化学性质进行了表征. 结果表明, Li[TFO-TFSI]/碳酸酯电解液具有较好的电化学稳定性; 在4.2 V(vs. Li/Li⁺)以下Al箔不发生腐蚀; 室温下基于Li[TFO-TFSI]/碳酸酯电解液的Li/人造石墨和人造石墨/LiCoO₂电池均保持较好的循环性能, 特别是人造石墨/LiCoO₂锂离子电池循环100周后, 其比容量保持率明显高于相应的基于LiPF₆/碳酸酯电解液体系的电池.     

二氟二草酸硼酸锂对LiFePO4/石墨电池高温性能的影响

研究了二氟二草酸硼酸锂(LiODFB)作为锂盐加入到碳酸丙烯酯(PC)+碳酸乙烯酯(EC)+碳酸甲乙酯(EMC)(质量比为1:1:3)混合溶剂中对LiFePO4/石墨电池高温(60 ℃)循环性能的影响. 用线性扫描伏安法(LSV)测试了电解液的电化学窗口. 通过等离子发射光谱(ICP)和能量散射光谱(EDS)对LiFePO4材料高温条件下在不同电解液中的稳定性进行了研究; 并用扫描电镜(SEM)和电化学交流阻抗谱(EIS)分析了石墨负极表面的固体电解液相界面(SEI)膜的热稳定性. 结果表明: 一方面LiODFB基电解液能抑制LiFePO4材料在高温条件下Fe(II)的溶解, 防止溶解的Fe(II)在石墨上还原, 有效地降低电池阻抗; 另一方面, 在LiODFB基电解液中形成的石墨负极表面SEI膜具有更好的热稳定性, 能显著提高LiFePO4/石墨电池的高温循环性能.     

锂钠合金的原位电化学制备及“锂+钠”共储特性

锂钠合金相较于单一锂或者单一钠具有更优异的性能,以钠金属为正极、锂金属为负极,以LiPF₆、NaClO₄以及锂钠混合离子电解液作为电解液,组装成纽扣电池,在梯度电流密度下进行充放电,成功实现了锂钠合金的原位电化学制备。得益于锂、钠双电化学活性离子的协同效应,不同钠含量的锂钠合金为负极的锂钠混合离子电容器均呈现良好的电化学性能。尤其是低钠量的锂钠合金负极,添加NaClO₄电解液时,活化的柠檬酸钾衍生碳（SCDC-活化）正极在1 A/g电流密度下循环300圈时仍能保持238 mA·h/g的比容量和99%的容量保持率。高钠量的锂钠合金负极,添加锂钠混合离子电解液时,SCDC-活化呈现了319 mA·h/g的比容量,并在循环1040圈时仍能保持93 mA·h/g的高比容量和98%的容量保持率。     

层状锰酸锂衍生物的阳离子价态与锂电池的电化学性能研究

采用溶胶-凝胶法, 通过锂盐、镍盐、钴盐与锰盐生成锂镍钴锰氧化合物的前驱体, 随后采用高温固相法合成了Li(Mn_1/3Co_1/3Ni_1/3)O₂. 借助于X射线光电子能谱(XPS)、X射线衍射(XRD)、循环伏安(CV)及充放电测试等现代测试手段研究了材料的晶型结构、离子价态及电化学性能. 前驱体经950 ℃煅烧可获得晶体结构完整、晶胞参数为a＝0.2864 nm, c＝1.4235 nm的六方层状Li(Mn_1/3Co_1/3Ni_1/3)O₂化合物; XPS结果表明Li(Mn_1/3Co_1/3Ni_1/3)O₂化合物表面上的Mn, Ni和Co分别以Mn^4＋, Ni^2＋和Co^3＋存在; 材料的高温放电比容量比室温要高, 在55 ℃下, 在2.5～4.6 V电压范围内, 电流密度为28 mA/g时材料首次放电容量195 mAh/g, 循环10次后容量保持在170 mAh/g; 循环伏安曲线上3.7 V和4.4 V的氧化还原过程对应于Ni^2＋/4＋和Co^3＋/4＋氧化还原电对的反应.     

“Water-in-salt”聚合物电解质制备及其电化学性能研究

为提高柔性锂离子电池安全性和循环稳定性能,本实验以自由基聚合结合冷冻干燥得到的聚丙烯酰胺膜为电解质载体,引入21 mol·kg^-1 LiTFSI 高浓度电解液,得到“water-in-salt”聚合物电解质。通过聚合物膜的形貌和孔道结构表征,红外光谱分析,离子电导率及电化学稳定窗口测试等对其基本物化特性进行了研究。冷冻干燥得到的聚丙烯酰胺膜内部具有大量微孔结构,有利于电解液的载入。将该吸附了电解液的聚合物电解质膜与锰酸锂(LiMn₂O₄)正极和磷酸钛锂(LiTi₂(PO₄)₃)负极组装全电池进行充放电性能测试。结果表明,制得的柔性聚合物电解质具有良好的拉伸性能,高离子电导率(20°C,4.34 mS·cm^-1)和宽电化学稳定窗口(3.12 V)。以“water-in-salt”聚合物电解质为隔膜组装的LiMn₂O₄||LiTi₂(PO₄)₃ 全电池表现出优异的倍率性能和长循环稳定性。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。