纳米碳酸钙/庚二酸复合成核剂对热致相分离法制备聚丙烯微孔膜的影响

以大豆油/邻苯二甲酸二丁酯(DBP)为混合稀释剂,采用热致相分离法(TIPS)制备聚丙烯(PP)微孔膜.研究了纳米碳酸钙成核剂、纳米碳酸钙/庚二酸复合成核剂对PP/大豆油/DBP(30/42/28,质量比)混合体系中PP结晶、熔融性能和PP微孔膜微观结构的影响.结果表明,单一纳米碳酸钙成核剂加入量为PP的0%~4%(质量百分率)时,PP/DBP/大豆油体系中PP熔融曲线上对应的峰值温度(Tpm)降到150.7~151.3℃,而纯PP的熔融峰值温度为165℃;DSC实验结果还显示加入1%~4%纳米碳酸钙和0.5%庚二酸后,导致PP的熔融曲线上出现了熔融双峰,说明纳米碳酸钙/庚二酸复合成核剂与单一成核剂相比有明显地促进β晶生成的作用,宽角X射线衍射(WAXD)实验进一步证实了β晶的存在.单一纳米碳酸钙成核剂对PP微孔膜的球晶结构和微观孔结构影响不大;加入纳米碳酸钙/庚二酸复合成核剂明显影响PP微孔膜的球晶结构和微观孔结构,其中0.5%庚二酸和1%纳米碳酸钙组成的复合成核剂制得的PP微孔膜的球晶结构明显,微孔膜孔径小且分布均匀;进一步增加纳米碳酸钙用量,PP微孔膜生成了许多细小的边界模糊的不规则结晶,微孔膜孔径不规则且尺寸较大,这与此时PP形成β晶结构有关.     

硅氧烷液晶共聚物作为β晶成核剂对等规聚丙烯结晶结构与形态的影响

采用广角X射线衍射(WAXD)与偏光显微镜(POM)等手段研究了硅氧烷液晶共聚物(LCP-O2)作为新型成核剂对聚丙烯(PP)共混样品结晶结构与形态的影响.结果表明,低浓度的LCP-O2在PP共混体系中起到异相成核的作用,使PP的晶核数目增多,球晶细化,并提高了结晶速度,同时也诱导出了β晶的形成.LCP-O2的成核效果主要依赖于其在PP中的相对含量、液晶的分子结构与结晶的热处理过程,且随着结晶温度或成核剂含量的增加,对应PP试样的β晶含量(Kβ)呈现先增加,后降低的趋势.当LCP-O2质量分数为1.0%,在130℃等温结晶1h,对应PP试样的Kβ最大,为58%.此外,属于单斜晶的α球晶呈现黑白颜色,晶束呈放射状生长,边界清晰;而属于三方晶的β球晶亮度要高于α球晶,其颜色艳丽多彩,束状晶片聚集体呈支化生长,内部排列比α晶疏散,边界相对模糊,且β晶与α晶的形态分别在157和171℃完全消失.     

聚丙烯/累托石纳米复合材料的非等温结晶动力学研究

在双螺杆挤出机上熔融共混制备了聚丙烯 (PP) 有机累托石 (OREC)纳米复合材料 ,采用广角X 射线衍射 (WAXD)定性地分析了PP OREC纳米复合材料及纯PP的结晶形态 ,由半峰宽定性地判断了对应晶面法向的晶粒的大小 .结果表明有机累托石没有改变聚丙烯的结晶晶型 (纳米复合材料主要还是α晶型 ) ,但是细化了晶粒的尺寸 .采用差示扫描量热法 (DSC)定量地研究了复合材料的非等温熔融结晶动力学 ,对所得数据分别用Jeziorny法的Mo法进行了处理 ,表明非等温结晶动力学参数Zc 及Avrami指数n随冷却速率的增加而增加 ,复合材料的Avrami指数n大于纯PP的n ;对相同配比的纳米复合材料 ,随着结晶度的增加 ,单位结晶时间里达到一定结晶度所需要的降温速率F(T)增大 ,对同一个设定的结晶度 ,纳米复合材料的F(T)比纯PP的小 ,说明需要的降温速率减小 .所有这些均说明有机累托石可作为聚丙烯的结晶成核剂 .     

GMA/苯乙烯多组分单体接枝聚丙烯结晶行为研究

使用差示扫描量热计 (DSC)研究了甲基丙烯酸缩水甘油酯 苯乙烯 (GMA St)多单体熔融接枝聚丙烯[PP g (GMA co St) ]的等温和非等温结晶行为 ,用偏光显微镜观察了结晶的形态 ,并利用Avrami方程对其结晶动力学进行了分析 .研究发现接枝聚丙烯的结晶模式与PP相似 ,属于异相成核控制的球晶三维生长 ;但接枝聚丙烯的结晶温度 (Tc)显著提高 ,幅度高达 16～ 19℃ ,总结晶速率与纯PP相比明显加快 .接枝聚丙烯上GMA co St支链的存在 ,降低了成核界面自由能 ,促进了聚丙烯结晶的异相成核 .在接枝率不太高的情况下 ,随着接枝率的提高 ,接枝聚丙烯的结晶温度升高 ,总结晶速率加快 .在高接枝率范围内 ,随着接枝率的提高 ,接枝PP的Tc 不再升高 ,且由于接枝链的增长严重阻碍了球晶生长 ,导致接枝PP的总结晶速率反而随接枝率的升高而下降     

表面接枝改性纳米二氧化硅填充聚丙烯的结晶行为

应用差示扫描量热方法研究了纳米二氧化硅 (SiO2 )及其表面接枝改性对聚丙烯 (PP)结晶过程、等温与非等温结晶动力学的影响 ,并研究了上述等温结晶的熔融行为和平衡熔点 .研究发现纳米SiO2 具有明显的异相成核效应 ,能够提高PP的结晶温度、熔融温度、结晶度和结晶速率 ,但降低聚丙烯结晶的完善程度 .粒子的表面接枝处理 ,因改善了粒子与基体的亲和性而有利于粒子成核效应的提高 ,而且此效应尚与粒子的分散相关     

自成核对等规聚丙烯结晶行为和性能的影响

结晶聚合物的结晶动力学影响其形态结构 ,而形态结构的变化对材料的性能有着重要的影响 [1] .成核剂能有效地降低聚合物的球晶尺寸 ,提高材料的性能 [2 ] ,因此被广泛地应用于工业生产中 .自成核 (self- seeding nucleation)是指聚合物自身的微小晶粒作为晶核而诱导结晶生长的一种成核方式 [3 ,4 ] ,它具有很高的成核效率 ,并能有效地降低球晶尺寸 .本文研究了等规聚丙烯的自成核过程、结晶行为、形态结构及其对材料性能的影响 .1　实验部分1 .1　样品的制备　等规聚丙烯 (i PP)为广东茂名石油化学工业公司产品 ,牌号为 T3 6 F.将 i PP粒…     

丙烯酸及其接枝物对纳米CaCO3/PP结晶与熔融行为的影响

制备了丙烯酸(AA)及其接枝聚丙烯(PP—g-AA)改性的纳米CaC03／PP复合材料。用DSC研究了纳米CaCO3对PP、PP-g-A和AA对纳米CaCO3／PP中PP结晶与熔融行为的影响。结果表明：随纳米CaCO3用量增加，PP结晶与熔融温度提高，PP—g—AA加入使PP结晶温度进一步提高，PP的结晶温度也随从用量增加而提高；在过氧化二异丙苯(DCP)存在下，少量AA能明显提高PP的结晶温度，但增加从用量对结晶温度的影响较小；WAXD证实纳米CaCO3／PP复合材料中存在β晶。     

多壁碳纳米管/聚丙烯复合材料的晶型及非等温结晶动力学

采用熔融共混法制备了多壁碳纳米管/聚丙烯(MWNT/PP)复合材料,利用X射线衍射法(XRD)、差示扫描量热法(DSC)分别研究了纯聚丙烯(PP)及MWNT/PP复合材料的晶型和非等温结晶动力学行为,并运用Mo法研究了纯PP及MWNT/PP复合材料的非等温结晶动力学行为。结果表明,多壁碳纳米管(MWNT)的加入使PP发生了由β晶型向α晶型的转变。MWNT在结晶过程中具有异相成核效应,提高了PP的结晶温度和结晶速率。MWNT/PP复合材料的结晶活化能均明显高于纯PP。MWNT的加入使PP在单位时间内达到一定结晶度所需的降温速率减小。     

月桂酸碱金属离子盐/芳基杂环磷酸铝盐复配体诱导等规聚丙烯结晶成核作用

以芳基杂环磷酸铝盐(AHP-Al OH)作为成核主体,分别含有Li+、Na+、K+3种碱金属离子的月桂酸盐(alkali metal salt of lauric acid,AMSLA)为配体,研究了该类复配体系协效诱导等规聚丙烯(i PP)成核作用规律.通过偏光显微观察、示差扫描量热分析、力学性能测试、光学性能测试以及耐热性能表征等手段,研究不同碱金属离子对复合材料结晶结构、结晶行为以及力学性能、光学性能、耐热性的影响.结果表明,Li L、Na L和KL对i PP的成核作用较差,对球晶尺寸的细化不明显,平均尺寸为161μm,与纯i PP在球晶尺度在同一数量级,结晶温度提高小于6.5℃,成核有效性低于20%,对复合材料力学性能、光学性能及耐热性的改善非常有限;APH-Al OH对i PP的成核作用达到中等水平,晶体尺寸比纯i PP减小了1个数量级,达到16μm,结晶温度提高13.7℃,成核有效性提高到45.4%,力学性能,光学性能及耐热性同样达到中等水平;Li L、Na L和KL与APH-Al OH复配后对i PP的球晶尺度迅速减小至5μm以下,比纯i PP球晶尺寸小2个数量级,结晶峰值温度可提高20℃以上,成核有效性高达60%以上,拉伸强度、弯曲强度、弯曲模量平均分别提高15.0%、44.2%、64.0%.雾度值平均下降72.8%,透光率平均增加13.9%,热变形温度平均升高53.8%.AMSLA和APH-Al OH之间表现出极强的协效成核作用,AMSLA中碱金属阳离子对复配体之间的协效成核作用影响对不同性能之间有不同表现,其对结晶峰值温度,力学性能、耐热性能方面的影响表现为Na+K~+Li~+,而对光学性能方面表现为Li~+Na~+K~+.     

等规聚丙烯自成核的等温结晶动力学

近年来 ,有关等规聚丙烯 (i PP)的自成核研究已引起了人们的关注 [1 ] ,但有关其结晶动力学的报道并不多见 .Carfagna等 [2 ]用膨胀计法研究了 i PP在未完全熔融重结晶情况下的等温结晶动力学 ,得到的 Avrami指数远远小于 3 .张新远等[3 ] 研究了 i PP未完全熔融情况下的非等温结晶动力学 .到目前为止 ,i PP自成核的熔体降温等温结晶动力学尚未见报道 .本文在 i PP自成核研究的基础上 [4] ,用 DSC方法研究了 i PP自成核在较高温度下的等温结晶动力学 ,讨论了结晶机理 .结果表明 ,在本实验的自成核条件下 ,i PP依然是三维球晶生长 ,…     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.