催化动力学分析法测定痕量铜

研究了在氨性介质中，Ｃｕ（Ⅱ）催化Ｈ２Ｏ２氧化噻嗪红Ｒ的退色反应，据此建立了催化动力学光度测定Ｃｕ（Ⅱ）的新方法，方法的线性范围为０．００５－０．５μｇ／２５ｍｌ。曾应用于水、猪肝和小麦粉标准物质中痕量铜的测定，获得满意结果。     

离子对高效液相色谱－TPPS_4光度法测定痕量锰锌铜的研究

本实验用磺化四苯基卟啉作柱前衍生试剂，研究了在Ｈｇ（Ⅱ）催化下，于ｐＨ５．５时，ＴＰＰＳ_４与Ｍｎ（Ⅱ）、Ｚｎ（Ⅱ）、Ｃｕ（Ⅱ）的配位反应，提出了以苄基三乙基氯化铵作离子对试剂，反相离子对高效液相色谱－光度法分离和测定痕量Ｍｎ（Ⅱ）、Ｚｎ（Ⅱ）、Ｃｕ（Ⅱ）的新方法，检测下限（×１０~（－９）ｇ／ｍＬ）：Ｍｎ~（２＋）０．１５，Ｚｎ~（２＋）０．２０，Ｃｕ~（２＋）０．１１。所确立的方法用于茶汤中锰、锌、铜的测定，结果满意。     

催化还原褪色光度法测定粉煤灰中微量铜

在ＰＨ５．０的ＨＡｃ－ＮａＡｃ缓冲休系中,痕量Ｃｕ（Ⅱ）催化抗坏血酸还原偶氮胭脂红Ｂ的褪色反应,褪色程度与Ｃｕ（Ⅱ）量在一定范围内线性相关。建立了测定痕量Ｃｕ（Ⅱ）的光度法,检出限为３．５＊１０＾－１１ｇ／ｍＬ,褪色程度与Ｃｕ（Ⅱ）量在０．０－２．０μｇ／Ｌ范围内符合比耳定律。本法结合Ｎ５３０－Ｎ５１０混合萃取剂萃取分离,测定了粉煤灰中的微量铜。     

抗坏血酸-偶氮胭脂红B体系催化光度法测定痕量铜

１引言催化光度法测定铜已有很多篇报道．本文基于ＨＡｃ－ＮａＡｃ介质中，痕量Ｃｕ（Ⅱ）对抗坏血酸还原偶氮胭脂红Ｂ的褪色反应的催化作用，建立了催化光度法测定痕量铜的新方法。方法灵敏度为３．２６×１０－９ｇ／Ｌ；测定范围为０～２μｇ／ＬＣｕ２＋；对１０ｍＬ体积中１５ｎｇＣＵ２＋重复测定１１次的相对标准偏差为１．２８％。本法是目前同类方法中灵敏度最高，选择性和重现性最好的体系之一。应用于血清、面粉和白酒中痕量铜的测定，结果令人满意。２实验部分２．１主要仪器和试剂７２２型分光光度计。铜标准溶液用ＣＵＳＯ４…     

催化光度法测定煤矸石中微量铜的研究

在乙酸－乙酸钠介质中痕量铜对抗坏血酸还原二溴对甲基偶氮羟（２－Ｂｒ－ｐＭＡＣ）褪色反应有催化作用,催化程度与Ｃｕ（Ⅱ）量线性相关。借此建立了测定痕量Ｃｕ（Ⅱ）的分光光度法。实验表明,有色溶液所最大吸收波长为５８６ｎｍ,方法检出限为０．０４８μｇ／Ｌ,Ｃｕ（Ⅱ）量在０￣０．８μｇ／５０ｍＬ范围内符合比耳定律,可用于测定煤矸石中的微量铜。     

1，2－亚丙基双（草酰胺根）桥联的线性三核铜（Ⅱ）配合物的合成与磁性

本文合成和表征了四种新的三核铜（Ⅱ）配合物｛［Ｃｕ（Ｌ）］２［Ｃｕ（ＣＨ３－ｅｂｏ）］｝（ＣｌＯ４）２（ＣＨ３ｅｂｏ表示１，２－亚丙基双（草酰胺根），Ｌ表示１，１０－菲咯啉（ｐｈｅｎ）（１），５－硝基－１，１０－菲咯琳（ＮＯ２－ｐｈｅｍ）（２），２，２’－联吡啶（ｂｐｙ）（３）和４，４’－二甲基－２，２’－联吡啶（Ｍｅ２ｐｙ）（４））．测定了四种配合物的变温磁化率（７７－３００Ｋ），求得交换参数分别为Ｊ１＝－２１９．６ｃｍ－１，Ｊ２＝－１９１．７ｃｍ－１，Ｊ３＝－２００．８ｃｍ－１，Ｊ４＝－１８５．５ｃｍ－１，表明Ｃｕ（Ⅱ）－Ｃｕ（Ⅱ）离子间存在着强的反铁磁交换相互作用．     

新催化动力学光度法测定痕量铝

根据ＡＩ＾３对ＫＢｒＯ３氧化Ｂａｎｇ花青褪色的催化行为,建立了测定痕量铝的催化动力学动力学分析方法。本法线性范围为０～１６０ｎｇ．ｍＬ＾－１,检出限为１．０ｎｇ．ｍＬ＾－１。除Ｃｕ＾２＋、Ｆｅ＾３＋、Ｃｒ（Ⅵ）外,其余离子均不影响测定。Ｆｅ＾３＋和Ｃｕ＾２＋、Ｃｒ（Ⅵ）的干扰可分别有效消除。测定了人发、茶叶和不中的,加标回收率为９８．４％～１０２％,ＲＳＤ为１．３％～２．１％（ｎ＝６）。     

析相光度法测定铜（Ⅱ）的研究

本文研究了Ｃｕ（Ⅱ）－ＰＥＧ（聚乙二醇－２０００）－Ｚｉｎｃｏｎ（锌试剂）－（ＮＨ４）２ＳＯ４体系的析相光度法并应用于测定Ｃｕ（Ⅱ）。最宜酸度为ｐＨ５．５～８．５（ＫＨ２ＰＯ４－Ｋ２ＨＰＯ４）缓冲溶液）其络合物的最大吸收位于６１０ｎｍ，表观摩尔吸光系数为４．０×１０＾４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，Ｃｕ（Ⅱ）浓度在０～１．５ｍｇ／Ｌ范围内服从比尔定律，铜与Ｚｉｎｃｏｎ形式组成为１：２的稳定的蓝色络     

固相萃取预富集—液相色谱分离测定痕量钴,铜,汞的研究

本文报道了固相萃取预富集处理样品继以液相色谱分离测定痕量Ｃｏ（Ⅱ）、Ｃｕ（Ⅱ）和Ｈｇ（Ⅱ）的方法。用二乙基二硫代氨基甲酸钠作络合剂及乙醇作洗脱液的预富集系统能在线富集Ｃｏ（Ⅱ）、Ｃｕ（Ⅱ）和Ｈｇ（Ⅱ），富集倍数与富集时间成正比。对实验的最佳条件进行了探讨。用于测定合成水样中Ｃｏ（Ⅱ）、Ｃｕ（Ⅱ）和Ｈｇ（Ⅱ），回收率分别为９７．１％、９７．７％和９６．９％。相对标准偏差为３．５％、２．７％和２．６％     

金属离子与卟啉的嵌入反应动力学研究──Ⅶ．一元酸根催化Cu(Ⅱ)与溴化间－四(N－乙酸甲酯基－3－吡啶基)卟啉的配位反应

研究了在３５±０．１℃、离子强度０．５ｍｏｌ／Ｌ（ＫＣｌ）条件下，甲酸根、乙酸根、丙酸根和丁酸根分别催化Ｃｕ（Ⅱ）离子与四溴化间－四（Ｎ－乙酸甲酯基－３－吡啶基）卟啉（Ｈ２Ｔβ－Ｎ－ＡＣＭｓｐｙＰＢｒ４）的反应动力学及其机理，该类反应对卟啉和Ｃｕ（Ⅱ）离子均为一级反应，反应动力学方程为：ｄ［ＣｕＰ＾４＋］／ｄｔ＝ｋ｛１．０＋ｂ［Ａ＾－］）／（１．０＋Ｋ３，４．［Ｈ＾＋］＾２｝［Ｃｕ＾２＋］［Ｐ］Ｔ     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.