TiO2浓度对核-壳结构Ag/TiO2纳米复合粒子结构以及三阶非线性光学性质的影响

采用光还原方法制备了核-壳结构的Ag/TiO2纳米复合粒子, 通过TEM、UV-Vis光谱和XRD表征了不同TiO2浓度下Ag/TiO2纳米复合粒子的结构和光学性质. UV-Vis光谱证明了银颗粒的存在, 且复合粒子中的银粒径随着TiO2含量的增加而增加, 同时随着TiO2浓度的增加, 银的吸收峰出现明显的增强和展宽；从TEM照片 发现, Ag/TiO2纳米复合粒子是一种以Ag为核, 外面包覆一层TiO2的核-壳结构, TiO2浓度和Ag+浓度的增加, 使得复合粒子的银颗粒粒径增大. 用Z-扫描技术, 以锁模Ti:sapphire飞秒激光器发出的脉宽为130 fs激光做光源, 在790 nm波长的光作用下, 研究了0.5%(w)Ag+含量, 不同TiO2浓度的Ag/TiO2纳米复合粒子的非线性光学特性. 结果发现, 在790 nm激光作用下, 0.25%(w)TiO2样品膜有双光子吸收和自聚焦非线性折射现象; 而当TiO2浓度为0.70%(w)时, 样品膜的非线性吸收由反饱和吸收转变为饱和吸收.     

TiO_2/Ag_2NCN复合光催化剂的制备与可见光催化性能

利用银盐与单氰胺水溶液的沉淀反应,通过共混不同质量分数的纳米TiO2粒子制备了TiO2/Ag2NCN复合光催化剂.使用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、傅里叶变换红外(FTIR)光谱仪和紫外-可见(UV-Vis)吸收光谱仪对复合光催化剂的结构进行了表征.结果表明,锐钛矿相TiO2纳米颗粒沉积在Ag2NCN表面形成异质结构,二者间以弱的物理作用力相结合.TiO2的掺杂使得复合颗粒的UV-Vis吸收光谱发生红移,带隙变窄.以亚甲基蓝(MB)为光催化降解对象,研究了TiO2/Ag2NCN复合颗粒的可见光催化活性.结果表明,与单一Ag2NCN相比,复合颗粒表现出增强的光催化性能.对TiO2/Ag2NCN复合颗粒的光催化反应动力学过程及光催化机理进行了探讨.     

层状K4Ag2Sn3S9·2H2O的溶剂热合成与表征

用溶剂热法合成了K4Ag2Sn3S9·2H2O,通过单晶X射线衍射、DSC、TG、IR和紫外漫反射光谱等手段对其进行了表征.结果表明,K4Ag2Sn3S9·2H2O属单斜晶系,P21/m空间群,a=0.78071(2)nm,b=2.73508(1)nm,c=1.05008nm,α=90°,β=103.87(6)°,γ=90°,Z=4.其层状结构内具有一维孔道,钾离子分离在层间及层内孔道中.     

TiO2/LaFeO3微纳米纤维的可控制备及光催化性能简

利用静电纺丝技术及水热合成法制备了TiO2/LaFeO3异质结构. 采用场发射扫描电子显微镜(FE-SEM),X射线衍射(XRD),傅里叶变换红外(FTIR)光谱和紫外-可见漫反射光谱(UV-Vis)等手段对TiO2/LaFeO3微纳米纤维的结构和表面形态进行表征. 通过亚甲基蓝(MB)光降解反应研究了其光催化性能. 结果表明,不完全碳化TiO2纤维表面的缺陷位点是LaFeO3纳米粒子的有利生长点. TiO2/LaFeO3异质结材料的带隙明显窄于TiO2,光催化活性得到提高;经140 min紫外光照射后,TiO2/LaFeO3异质结催化剂对MB的降解率为65.34%,分析和探讨了其光催化机理.     

TiO2电极表面氰基吡啶吸附的电化学SERS光谱

采用基于核壳纳米粒子的壳层隔绝纳米粒子增强拉曼(SHINERS)以及Au纳米粒子增强技术, 对比研究了4-氰基吡啶(4-CNPy)在TiO2表面的吸附行为. 结果表明, 采用2种技术所获得的光谱存在明显的差别. 利用前者得到了4-CNPy在TiO2电极上随电极电位变化的吸附方式. 在电位为0时, 分子以吡啶环上的N垂直吸附; 随电位负移, 部分分子变为倾斜吸附, 且在电位为-1.0 V时倾斜角度变大. 在正电位区间, 分子始终以吡啶环上的N垂直吸附. 而采用Au纳米粒子滴加在TiO2电极上的方式, 则得到吸附在TiO2, Au及TiO2/Au复合结构上的总光谱信息.     

可见光响应的LaVO4/TiO2 纳米管的合成、表征及对气相甲苯的光催化性能

通过水热方法合成了可见光响应的LaVO4/TiO2纳米管, 采用XRD, TEM, 氮气吸附-脱附以及表面光电压谱对样品进行了表征. 以气相甲苯为典型污染物, 研究了制备样品在可见光(λ＞420 nm)条件下的光催化性能. 实验结果表明, LaVO4的复合使TiO2的粒径减小, 比表面积增大, 光响应范围向可见光偏移. 光催化实验结果表明, 在可见光条件下, LaVO4/TiO2纳米管降解甲苯的效率比其它样品高, 与纯TiO2纳米管相比, 降解效率提高了47%.     

纳米复合材料Ag/TiO_2-ZrO_2的制备及其微波增强光催化降解甲基橙

采用EO20PO70EO20(P123)作模板剂,通过溶胶-凝胶-程序升温溶剂热一步法,并经萃取处理制备了具有光催化活性的纳米复合材料Ag/TiO2-ZrO2.用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、N2吸附-脱附测定和扫描电子显微镜配合X射线能量色谱仪(SEM-EDS)等测试手段对其组成、结构及形貌等进行了表征.结果表明,复合材料Ag/TiO2-ZrO2中Ag以单质形式存在,材料具有双孔结构,颗粒分布较均匀,结构也较规整,平均孔径约为3.6和9.0nm.通过微波增强光催化降解染料甲基橙的实验,对复合材料Ag/TiO2-ZrO2的光催化活性进行了探究.实验结果表明,微波辅助光催化效果优于紫外辐射,并且萃取后的合成产物Ag/TiO2-ZrO2在90min内对甲基橙的降解率可达81.5%,其活性高于市售P25以及TiO2-ZrO2.     

高活性Ag修饰TiO2空心八面体光催化剂的简易模板诱导合成

贵金属修饰的TiO2空心纳米光催化材料由于具有大的比表面积、低的质量密度、良好的表面渗透性、强的光吸收能力以及界面电荷的快速转移,因而表现出优异的光催化性能.为了制备结构可控且精良的贵金属修饰TiO2空心纳米光催化材料,人们先后采用湿化学法、高温固相法、声化学法及光化学沉积法等.由于在制备过程中涉及多种异相材料的合成和结构控制,因此上述合成方法通常需要复杂且多步过程(有些过程甚至很容易导致结构破坏),从而限制了其在光催化领域的实际应用.本文开发了一种简单的模板诱导法,成功制备了Ag纳米粒子修饰的TiO2空心八面体光催化剂.合成过程包括模板指导沉积和原位模板溶解.以Ag2O八面体为模板, TiF4水溶液为前驱体,首先通过TiF4水解形成TiO2纳米粒子沉积在Ag2O模板表面,而TiF4水解产生的酸性HF水溶液可原位溶解碱性的Ag2O模板,从而一步制得TiO2空心八面体.同时,利用Ag2O以及Ag+离子的光敏特性,在光照条件下使Ag2O和Ag+离子生成Ag纳米颗粒,直接沉积在TiO2空心八面体的内外表面,得到Ag/TiO2光催化剂.由此可见,该合成方法具有明显的步骤少的优点.扫描电镜、透射电镜、能量散射和紫外-可见光谱等表征结果表明成功制得内外Ag纳米粒子修饰的TiO2空心八面体光催化剂,其中TiO2空心八面体的壁厚约为25 nm,边长约为1μm,而修饰在其表面的Ag纳米粒子尺寸仅为5–10 nm.此外,通过控制TiF4前驱体浓度,还可制备核壳结构的Ag2O@TiO2八面体以及不同壁厚Ag修饰的TiO2空心八面体,表明该方法在Ag/TiO2形貌合成上的多样性和可控性.为了获得良好的光催化活性,对制备的Ag纳米粒子修饰的TiO2空心八面体光催化剂进行了不同温度的热处理. X射线衍射结果表明,即使在600 oC高温下,制备的Ag/TiO2空心八面体光催化剂依然能够保持原有的特殊形貌和锐钛矿TiO2晶型.该温度明显高于TiO2从锐钛矿向金红石转变的温度.这说明合成的Ag/TiO2能在保持高活性锐钛矿相的同时获得更好的结晶性.这可能是由于分散在TiO2原始晶粒周围的Ag纳米粒子能阻止其进一步长大,从而抑制了其晶型转变.不同样品光催化降解甲基橙的结果表明,经600oC高温热处理的样品表现出最高的光催化活性,相应的反应速率常数为0.11 min？1.这应得益于该光催化剂具有以下三个特点：(1) TiO2空心八面体的薄壁结构能够缩短光照条件下光生电子和空穴从内部扩散到表面的距离;(2)由于贵金属Ag纳米粒子沉积在TiO2薄壁的内外两个表面以及TiO2和Ag形成肖脱基势垒,因此在它们接触的界面上能够发生更快的界面电荷转移;(3)高温处理导致TiO2良好的晶化以及高活性锐钛矿TiO2晶型的保持.     

Ag修饰的Fe_3O_4/TiO_2复合磁性纳米纤维的制备及光催化性能

通过静电纺丝法制备了含有Fe3O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见光谱(UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B(Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构,Fe3O4纳米粒子均匀分布在TiO2纤维中,Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外,Fe3O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.     

ZnIn2S4/TiO2/Ag复合光催化剂的制备及分解水制氢性能

首先采用溶剂热法将1D TiO_2纳米带均匀地穿插到片层结构组装而成的3D ZnIn_2S_4微球中,所形成的异质结构能有效抑制光生电子-空穴对。其次利用光沉积法将0D Ag纳米粒子负载在3D ZnIn_2S_4/1D TiO_2异质结构上。得益于0D Ag纳米粒子的等离子体效应及电子助催化剂作用,三元3D ZnIn_2S_4/1D TiO_2/0D Ag复合光催化剂在分解水制氢方面表现出优异的性能。在模拟太阳光照射下,ZnIn_2S_4/TiO_2/Ag复合光催化剂的产氢速率达到715μmol·g~(-1)·h~(-1),相对于ZnIn_2S_4/TiO_2、ZnIn_2S_4/P25、ZnIn_2S_4、TiO_2和P25分别提高了2.7倍、3.3倍、3.8倍、184倍和518倍。同时借助于X射线衍射、扫描电子和透射电子显微镜、X射线光电子能谱和紫外可见漫反射光谱等表征手段进一步论证了复合催化剂的优异性能。     

Crystallization and photovoltaic properties of titania-coated polystyrene hybrid microspheres and their photocatalytic activity

The hybrid microspheres with polystyrene core coated by titania nanoparticles were prepared by miniemulsion polymerization, and the as-prepared samples were characterized by SEM, XRD, TG-DTA, XPS, and SPS techniques. TiO2 nanoparticles experienced two processes of phase transition, i.e., amorphous to anatase and anatase to rutile at the calcining temperature range from 400 to 1000 degrees C. The phase transformation temperature of TiO2 hybrid microspheres from anatase to rutile was increased by about 300 degrees C due to the blocking function of calcined polymer remainder. SPS results present that the band-gap of hybrid microspheres is 3.2-3.4 eV, which is larger than that of pure TiO2. The maximum intensity of the SPS signal is about 3 times larger for the hybrid material as compared to the pure TiO2. In addition, the photocatalytic degradation rate of TiO2 hybrid microspheres was 15% faster than that of pure TiO2 in the experiment of the photocatalytic degradation of methyl orange.     

Ag／TiO2复合纳米催化剂的制备和表征及其光催化活性

 采用光还原沉积贵金属法，制备了Ag／TiO2复合纳米催化剂．通过调节溶液的pH值控制TiO2表面负载银的形貌，利用AAS，XRD，TEM和XPS等手段对样品进行了表征．以苯胺氧化为模型反应，考察了Ag／TiO2复合纳米催化剂样品的光催化活性以及银沉积量和沉积形貌对催化剂活性的影响．结果表明，通过调控光还原沉积条件，可在平均粒径为24nm左右的TiO2颗粒上获得3nm左右均匀分散的银粒子；在TiO2上沉积适量的具有较高分散度的金属Ag，能有效提高TiO2对苯胺氧化反应的光催化活性．     

Control of TiO2 structures from robust hollow microspheres to highly dispersible nanoparticles in a tetrabutylammonium hydroxide solution

A new process for controlling the structure of TiO2 from hollow microspheres to highly dispersible nanoparticles has been developed by altering the concentration of tetrabutylammonium hydroxide (TBAH) in the solvothermal reaction of titanium isopropoxide. Robust and size-controllable hollow TiO2 microspheres, constructed by the assembly of 18 nm TiO2 nanoparticles, were synthesized at relatively high TBAH concentration. The diameters of hollow spheres, with a shell thickness of approximately 250 nm, were controlled to 1.5-4 microm by varying the concentration of TBAH in the range of 0.1-0.5 M. After calcination at 450 degrees C, the hollow microspheres were not appreciably deformed and were still floating on the surface of the water. However, highly dispersible TiO2 nanoparticles with an average diameter of 13 nm were obtained at a low TBAH concentration such as 9.2 mM. The colloidal particle size of TiO2 in an aqueous suspension at pH 2 was 12.5-13.5 nm, which indicates that the each nanoparticle is completely separated. The overall procedure is simple and highly reproducible, and large-scale synthesis is available at low cost.     

Preparation of highly uniform Ag/TiO2 and Au/TiO2 supported nanoparticle catalysts by photodeposition

Photodeposition of Ag nanoparticles on commercial TiO2 particles and nanoparticles was performed in order to provide direct visualization of the spatial distribution of photoactive sites on sub-micrometer-scale and nanoscale TiO2 particle surfaces and to create materials for potential catalytic applications. HRTEM (high-resolution transmission electron microscopy) and HAADF-STEM (high-angle annular dark-field scanning transmission electron microscopy) were used to characterize these materials. The size and spatial distributions of the Ag nanoparticles on the commercial TiO2 were not uniform; the concentration of Ag was higher on grain boundaries and at the edges of these submicrometer particles. In the case of TiO2 nanoparticles, the size distribution of the Ag nanoparticles deposited was relatively uniform and independent of irradiation time and photon energy. The amount of Ag deposited on TiO2 nanoparticles was at least 6 times higher than that on the commercial samples for comparable irradiation conditions. Compared to the case of Ag photodeposition, the difference in the amount of Au photodeposited on TiO2 particles and nanoparticles was even greater, especially at low precursor concentrations. Photodeposition on TiO2 nanoparticles is suggested as a potential method for the preparation of Au/TiO2 catalysts, as loadings in excess of 10 wt % of uniform 1 nm metal particles were achieved in this work.     

WO3/TiO2纳米材料的制备及光催化性能

采用溶胶-凝胶法制备WO3/TiO2复合纳米光催化剂,掺入WO3、TiO2锐钛矿101峰的相对强度、平均晶粒直径与颗粒直径均减小,比表面积增大;WO3掺入摩尔比分别为2%、5%、8%时,新的LRS峰位分别出现在797、967及969cm-1;在380-460nm范围内,WO3/TiO2的反射率减小,XPS分析表明,WO3/TiO2晶体中存在W6+、W5+、W4+、和Ti4+、Ti3+。以亚甲基兰的光催化降解为反应模型,掺入WO3后,光催化活性增强,掺入摩尔比为2%时,WO3/TiO2的光催化活性最高。还讨论了光催化活性与性质的关系。     

Kinetic and DFT studies on the Ag/TiO2-photocatalyzed selective reduction of nitrobenzene to aniline.

TiO2 particles loaded with silver nanoparticles with a mean diameter of 1.5 nm exhibit a high photocatalytic activity (84 % conversion after 1 h irradiation) for the reduction of nitrobenzene to aniline with 100 % selectivity in the presence of CH3OH (concentration=100 mM). High-resolution transmission electron microscopic studies of Pt-photodeposited Ag/TiO2 demonstrate that the Ag nanoparticles act as reduction sites in the photocatalytic reaction. Both spectroscopic measurements and density functional theory (DFT) calculations reveal that nitrobenzene is selectively adsorbed onto the Ag surfaces of Ag/TiO2 via partial electron transfer from Ag to nitrobenzene, whereas the interaction between aniline and Ag/TiO2 is weak. The kinetic analysis indicates that the recombination between the electrons flowing into the Ag nanoparticle and the holes left in the TiO2 valence band is significantly suppressed, particularly in the presence of CH3OH. The high activity and selectivity in the present Ag/TiO2-photocatalyzed reduction are rationalized in terms of the charge separation efficiency, the selective adsorption of the reactants on the catalyst surfaces, and the restriction of the product readsorption.     

ZnO纳米粒子的表面光电压谱和光催化性能

采用焙烧前驱物碱式碳酸锌的方法制备了不同粒径的ZnO纳米粒子，而用粒径 最小的作为光催化剂，通过光还原过程分别得了贵金属质量分数为0.5%和0.75%的 Pd/ZnO或Ag/ZnO复合纳米粒子。利用XRD，TEM，XPS，SPS和EFISPS等测试技术对样 品进行了表征，并通过光催化氧化气相正庚烷评估了样品的光催化活性，考察了微 晶尺寸和贵金属Pd或Ag的沉积对ZnO纳米粒子表面光电压信号以及光催化活性的影 响，探讨了样品表面光电压谱与其光催化活性的关系，说明了可以通过表面光电压 谱的测试来初步地评估纳米粒子的光催化活性。结果表明：随着ZnO纳米微晶尺寸 的减小，其SPS信号强度逐渐变弱，而光催化活性逐渐升高；沉积适量的贵金属Pd 或Ag后，ZnO纳米粒子的SPS信号强度明显下降，而其光催化活性却有所升高。此外 ，对ZnO纳米粒子光催化剂的失活机理进行了分析。     

Spontaneous formation of core/shell bimetallic nanoparticles: a calorimetric study

We showed recently that low entropy core/shell structured nanoparticles form spontaneously from the physical mixture of a dispersion of Ag nanoparticles and that of another noble metal (Rh, Pd, or Pt) at room temperature. Here we use isothermal titration calorimetry (ITC) and show that the initial step of such a spontaneous process is strongly exothermic. When the alcohol dispersion of poly(N-vinyl-2-pyrrolidone) (PVP)-protected Rh nanoparticles (average diameter 2.3 nm) was titrated into the alcoholic dispersion of PVP-protected Ag nanoparticles, a strong exothermic enthalpy change, DeltaH, was observed: DeltaH = -908 kJ/mol for Ag(S) nanoparticle (average diameter 10.8 nm) and -963 kJ/mol for Ag(L) nanoparticles (average diameter 22.5 nm). The strength of interaction increases in the order of Rh/Ag > Pd/Ag > Pt/Ag. This strong exothermic interaction is considered as a driving force to from low entropy bimetallic nanoparticles by simple mixing of two kinds of monometallic nanoparticles. We show also that exothermic interactions occur between a pair of noble metal nanoparticles themselves by using ITC.     

TiO2晶型对Au/TiO2上光催化分解臭氧的影响

以不同晶型TiO2为载体,采用沉积-沉淀法制备了Au/TiO2光催化剂,并用紫外-可见漫反射光谱、X射线光电子能谱(XPS)和表面光电压谱(SPS)等手段进行了催化剂表征,详细考察了Ti O2晶型对Au/TiO2光催化分解臭氧活性的影响.结果表明,光催化分解臭氧的活性顺序为Au/P25>Au/Anatase>Au/Rutile,这与不同的单一Ti O2对光催化臭氧分解的活性顺序是一致的.但在TiO2上沉积金后,其对光催化臭氧的分解活性有了显著的提高.由催化剂的Au4fXPS分析发现,不同晶型Ti O2上的电荷向金簇迁移的能力有明显差异,加之载体本身对光催化臭氧分解活性不同,两者协同作用导致负载金催化剂光催化分解臭氧活性的不同.SPS信号强度与催化剂光催化活性有很好的对应关系,SPS信号越强,光生电子和空穴分离效率越高,光催化活性越好.