热扩散法制备MoO3/SiO2催化草酸二甲酯和苯酚酯交换反应

采用热扩散法（TS）和等体积浸渍法制备了MoO₃/SiO₂催化剂用于草酸二甲酯和苯酚酯交换反应.结果表明,热扩散法制备的10%MoO₃/SiO₂-TS催化剂较等体积浸渍法制备的10%MoO₃/SiO₂-C催化剂具有更好的催化性能.运用X射线衍射、Raman光谱、X射线光电子能谱分析、吡啶吸附红外光谱、NH₃程序升温脱附等手段对催化剂进行了表征,发现虽然两种方法制备的催化剂都只有弱Lewis酸中心,钼均以氧化钼单体形式存在,未形成解离和聚合,但是10%MoO₃/SiO₂-TS催化剂较10%MoO₃/SiO₂-C催化剂表面钼含量更高且MoO₃分散得更好.在苯酚用量为0.2mol,10%MoO₃/SiO₂-TS催化剂用量为1.2g,反应温度为180℃,草酸二甲酯与苯酚的摩尔比为2,反应时间为4h的优化条件下,苯酚转化率可达70.9%,甲基苯基草酸酯和草酸二苯酯的收率分别达63.1%和7.7%.     

有机钛催化草酸二甲酯与苯酚酯交换反应

研究了几种有机钛化合物对草酸二甲酯(DMO)与苯酚酯交换反应的催化性能,发现催化活性及选择性顺序依次为二氯二茂钛钛酸四苯酯钛酸丁酯乙酰丙酮氧钛钛酸乙酯钛酸异丙酯,表明二氯二茂钛是一种性能较好的酯交换催化剂.在n(Cp2TiCl2)=0.001 mol、n(DMO)=0.3 mol、n(Phenol)=0.2 mol、T=180℃、t=2 h优化工艺条件下,苯酚转化率可达44.0%,甲基苯基草酸酯(MPO)和草酸二苯酯(DPO)收率分别达37.8%和6.1%,酯交换总选择性为99.8%.     

有机钛催化草酸二甲酯与苯酚酯交换反应

研究了几种有机钛化合物对草酸二甲酯(DMO)与苯酚酯交换反应的催化性能,发现催化活性及选择性顺序依次为二氯二茂钛＞钛酸四苯酯＞钛酸丁酯＞乙酰丙酮氧钛＞钛酸乙酯＞钛酸异丙酯,表明二氯二茂钛是一种性能较好的酯交换催化剂。在n(Cp2TiCl2) = 0.001 mol、n (DMO) =0.3mol、n (Phenol) = 0.2mol、T=180癈、t=2h优化工艺条件下,苯酚转化率可达44.0%,甲基苯基草酸酯(MPO)和草酸二苯酯(DPO)收率分别达37.8%和6.1%,酯交换总选择性为99.8%。     

苯酚和草酸二甲酯在不同分子筛催化下的酯交换反应

研究了以TS－1、H－ZSM－5、Hβ和H－丝光沸石等不同分子筛为催化剂，苯酚和草酸二甲酯酯交换合成草酸二苯酯反应。通过对催化剂进行吸附吡啶的红外光谱和NH3－TPD表征，考察了不同分子筛催化剂的酸性和酸强度对草酸二苯酯合成反应的影响，确定了催化剂上的弱酸中心是催化苯酚和草酸二甲酯酯交换合成草酸二苯酯反应的活性位，且催化剂的酸性中心越多，酸量越大，催化活性越好。催化剂上的强酸中心促进了副产物苯甲醚的生成。     

Zn(OAc)2·2H2O催化苯酚和草酸二甲酯酯交换合成草酸二苯酯

研究了以Zn(OAc2·2H2O为催化剂时苯酚和草酸二甲酯酯交换合成草酸二苯酯的反应.采用气相色谱/质谱联用仪对主、副产物进行了定性,确定了中间产物甲基苯基草酸酯,并对反应过程的模式进行了探讨.考察了催化剂的催化性能及影响反应的因素.采用XRD技术对催化剂进行了表征,探讨了其失活原因.     

纳米SO42-/ZrO2的合成及其在酯交换反应中的催化性能

采用两步晶化-后浸渍法合成了纳米SO_4~(2-)/ZrO_2固体酸催化剂,并考察了其在植物油与甲醇酯交换反应中的催化性能。XRD、N2吸附-脱附和TEM等结果表明,经过600℃焙烧,催化剂仍保持单一四方相,粒径大小为5~10 nm,比表面积为137 m2·g~(-1),孔径为3.6 nm。NH3-TPD结果表明,随着焙烧温度升高,催化剂表面的酸含量和酸强度逐渐增加,超强酸含量的增加,更有利于反应在温和条件下进行。在酯交换反应中,当醇油物质的量之比为20∶1,反应温度为135℃,反应时间为6 h,600℃焙烧后催化剂用量为5%(w/w)时,植物油能够完全转化为脂肪酸甲酯。与传统的SO42-/Zr O2催化剂相比,该催化剂在低温反应条件下具有更高的催化性能和良好的重复使用性。     

一步法制备Bi2MoO6/CoMoO4绣花球结构及其光催化性能

以五水硝酸铋为铋源,采用简易的一步水热法合成出Bi_2MoO_6/CoMoO_4绣花球结构。通过X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶红外光谱(FT-IR)、紫外-可见漫反射光谱(UV-Vis DRS)、荧光光谱(PL)和电化学测试等表征对所制备催化剂的物相组成、微观形貌、光学性质以及光生电荷复合效率进行了分析。研究结果表明,引入Bi_2MoO_6之后,Bi_2MoO_6/CoMoO_4复合异质结的光吸收范围明显被拓宽,其光生电荷的分离率也得到了提升。以亚甲基蓝和头孢曲松钠为污染物来模拟废水,在可见光的条件下评估催化剂样品的光催化降解活性。在可见光下光照60 min后,Bi_2MoO_6负载量为30%(w/w)的复合物具有最佳的光催化性能,其降解速率常数约为纯CoMoO_4的2倍。基于实验的所有表征,进一步地研究了Bi_2MoO_6/CoMoO_4体系相应的光催化机理。     

CeO2掺杂RuO2/γ-Al2O3催化剂结构与湿式氧化降解苯酚的活性研究

采用浸渍法制备了RuO2/γ-Al2O3和RuO2-CeO2/γ-Al2O3催化剂,利用XRD,XPS和ESR分析了催化剂的结构,并研究了湿式氧化降解苯酚的活性.结果表明,两种催化剂表面RuO2均有良好的分散性,并且催化剂表面存在氧空位和化学吸附氧,CeO2的掺杂使催化剂表面氧空位和化学吸附氧数量增加.两种催化剂对湿式氧化降解苯酚具有良好的催化活性,当苯酚质量浓度为4200mg/L,在150℃和3MPa下,RuO2/γ-Al2O3催化剂湿式氧化降解苯酚反应150min后,苯酚全部被去除,RuO2-CeO2/γ-Al2O3催化剂反应60min后,苯酚的去除率为96%.     

TiO2-MoO3/SiO2催化碳酸二甲酯与乙酸苯酯酯交换合成碳酸二苯酯

采用分步等体积浸渍法制备了催化剂r%TiO2-q%MoO3/SiO2(1q-r)。以碳酸二甲酯(DMC)与乙酸苯酯(PA)酯交换合成碳酸二苯酯(DPC)为探针反应,考察了1的催化活性。优化反应条件为:PA 290 mmol,n(PA):n(DMC)=2:1,18-4 1.4 g,于180℃反应7 h。在优化反应条件下,DMC转化率77.5%,DPC选择性49.4%,碳酸甲苯酯和DPC的总选择性87.2%。催化剂重复使用时,活性下降很快,也很难通过高温焙烧再生。     

富氧条件下Cu/Al2O3催化剂上C3H6选择性还原NO的研究

以Cu/Al2O3为催化剂,对富氧条件下C3H6为还原剂选择性催化还原NO反应进行了研究.活性评价结果表明,与高活性的Ag/Al2O3催化剂相比,Cu/Al2O3催化剂选择性还原NO的活性较低,NO的最高转化率仅为40%.在所考察的温度范围(473～723K)内,红外谱图中不存在有机含氮化合物(R—ONO和R—NO2)的特征振动吸收峰.作为反应中间体—NCO的前驱体,有机含氮化合物在Cu/Al2O3催化剂表面难以生成是造成催化剂选择性还原NO活性低的直接原因.在Cu/Al2O3催化剂上,NO2吸附能够优先发生,并以NO3-物种的形式覆盖在大部分催化剂表面.动态原位红外光谱实验发现,这种NO3-表面物种与C3H6的反应性较差,使生成有机含氮化合物的关键反应难以发生,但此时的催化剂表面有利于C3H6和O2的完全氧化反应,这是导致Cu/Al2O3催化剂选择性较低的根本原因.     

Cr2(WO4)3和Cr2(MoO4)3的负热膨胀特性研究

用液相反应-前驱物烧结法制备了Cr₂(WO₄)₃和Cr₂(MoO₄)₃粉体。298～1 073 K的原位粉末X射线衍射数据表明Cr₂(WO₄)₃和Cr₂(MoO₄)₃的晶胞体积随温度的升高而增大, 本征线热膨胀系数分别为(1.274±0.003)×10^-6 K^-1和(1.612±0.003)×10^-6 K^-1。用热膨胀仪研究了Cr₂(WO₄)₃和Cr₂(MoO₄)₃在静态空气中298～1 073 K范围内热膨胀行为，即开始表现为正热膨胀，随后在相转变点达到最大值，最后表现为负热膨胀，其负热膨胀系数分别为(-7.033±0.014)×10^-6 K^-1和(-9.282±0.019)×10^-6 K^-1。     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

草酸盐共沉淀法制备Y1.84La0.16O3纳米粉体

Nanopowder of Y_1.84La_0.16O₃ was prepared by oxalate co-precipitation method. The powder was characterized by TG-DTA, XRD and TEM. The results show that the precursor is Re₂(NO₃)₂(C₂O₄)₂·2H₂O (Re=Y, La), and the Y_1.84La_0.16O₃ nanopowders produced by calcining the precursor at 1 000 ℃ for 4 h are 20～40 nm spherical particles and well dispersed. The powders were with high sintering activity and could be fabricated to transparent ceramic without additive at 1 450～1 550 ℃ in H₂ atmosphere for 3 hours. The total transmission of the transparent ceramic could reach 80%.     

Eu0.5RE0.5Fe0.5Mn0.5O3的57Fe Msosbauer谱研究

利用固相反应合成了Eu0.5RE0.5Fe0.5Mn0.5O3(RE=La,Pr,Nd,Sm,Eu,Gd,Tb,Dy,Ho,Er,Tm,Yb,Y)等化合物。测量了其XRD谱及57FeMssbauer谱。实验发现,随着RE原子序数的增加,样品的晶胞体积减小,Fe在化合物中处于Fe3+的高自旋状态,57Fe的四极裂矩与样品的畸变参数D成线性关系。     

可见光响应的Co3(PO4)2/Ag3PO4纳米复合光催化剂的制备及表征

采用简单的化学偏聚法合成出Ag₃PO₄纳米颗粒、磷酸钴（Co₃（PO₄）₂,CoP）纳米片以及它们两者的纳米复合结构（CoP/Ag₃PO₄）,同时还比较了它们的可见光催化活性. 采用场发射扫描电镜（FESEM）、X 射线衍射（XRD）、紫外-可见（UV-Vis）吸收光谱以及光致发光谱等手段对其形貌、结构、光学以及可见光催化性能等进行表征. 结果表明,CoP/Ag₃PO₄复合纳米结构的可见光降解甲基橙（MO）的速率和循环稳定性均明显优于其它两种物质. 这表明CoP应该起着共催化剂的作用,它能够抑制光生电子与空穴之间的复合,并且提供大量高活性的光生空穴. 此外,我们还发现CoP/Ag₃PO₄降解另一种阳离子型染料——罗丹明B（RhB）的能力则远不如纯Ag₃PO₄,这可能是与光催化剂的表面性质发生改变有关,造成更低的RhB吸附能力. 本文提供了一种廉价制备高效可见光催化剂的新方法.     

g-C3N4/Bi2O2CO32D纳米片复合材料的制备及可见光催化性能研究

采用自组装和化学沉淀法分别制得两种可见光驱动复合材料石墨相氮化碳/碳酸氧铋(g-C_3N_4/Bi_2O_2CO_3).采用X射线衍射光谱(XRD),紫外可见光谱、扫描电镜(SEM)、N_2吸附、电化学阻抗谱(EIS)和X射线光电子能谱(XPS)等分析手段对制备的催化剂进行了表征.结果表明,制备方法对纳米复合材料的晶相、形态及光学性能没有影响,但是影响g-C_3N_4和Bi_2O_2CO_3之间的相互作用力,导致光生电子-空穴对的分离速率存在显著差异.以可见光驱动苯酚和罗丹明B的降解实验为探针反应检测催化剂的光催化性能.实验结果表明自组装法得到的异质结催化剂中相互作用力更强,催化效果最高.O_2-是罗丹明B降解反应的主要活性物种,染料的光敏化、Bi_2O_2CO_3与g-C_3N_4综合效应,导致光生载流子电荷分离效率更高.     

Vibrational spectra of the peroxotantalates (NH4)3[Ta(O2)4], K3[Ta(O2)4], Rb3[Ta(O2)4] and Cs3[Ta(O2)4] and the crystal structure of Rb3[Ta(O2)4]

The compounds (NH₄)₃[Ta(O₂)₄], K₃[Ta(O₂)₄], Rb₃[Ta(O₂)₄] and Cs₃[Ta(O₂)₄] have been prepared and investigated by X-ray powder methods as well as Raman- and IR-spectroscopy. In the case of Rb₃[Ta(O₂)₄] the structure has been solved from single crystal data. It is shown that all these compounds are isotypic and crystallize in the K₃[Cr(O₂)₄] type (SG , No. 121). The infrared- and Raman spectra (recorded on powdered samples) are discussed with respect to the internal vibrations of the peroxo-group and the dodecahedral [Ta(O₂)₄]³⁻ ion. Symmetry coordinates for the [Ta(O₂)₄]³⁻ ion are given from which the vibrational modes of the O-O stretching vibrations of the O₂²⁻ groups, the Ta-O stretching vibrations and the Ta-O bending vibrations are deduced.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

A Structural Investigation of La2(GeO4)O and Alkaline-Earth-Doped La9.33(GeO4)6O2

The structures of the oxyorthogermanate La₂(GeO₄)O and the apatite-structured La_9.33(GeO₄)₆O₂ have been refined from powder neutron diffraction data. La₂(GeO₄)O crystallizes in a monoclinic unit cell (P2₁/c) and is cation stoichiometric in contrast to previous reports. La_9.33(GeO₄)₆O₂ crystallizes in a hexagonal unit cell (P6₃/m) and the powder diffraction data show anisotropic peak broadening that is observed in electron diffraction patterns as incommensurate diffuse spots at hkq reciprocal planes (with q=1.6-1.7) and can be attributed to a correlated disorder in the “apatite channels”. This compound was doped up to a nominal composition close to M₂La₈(GeO₄)₆O₂ with M=Ca, Sr, Ba. The dopant ions preferentially occupy the 4f sites as the number of La vacancies decreases. The measured ionic conductivity of La_9.33(GeO₄)₆O₂ is about 3 orders of magnitude larger than for La₂(GeO₄)O at high temperatures and decreases with increasing dopant content from the highest value of about 0.16 S cm⁻¹ at 1160 K.